| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The cn10k hardware ptp timestamp format has been modified primarily
to support 1-step ptp clock. The 64-bit timestamp used by hardware is
split into two 32-bit fields, the upper one holds seconds, the lower
one nanoseconds. A new register (PTP_CLOCK_SEC) has been added that
returns the current seconds value. The nanoseconds register PTP_CLOCK_HI
resets after every second. The cn10k RPM block provides Rx/Tx timestamps
to the NIX block using the new timestamp format. The software can read
the current timestamp in nanoseconds by reading both PTP_CLOCK_SEC &
PTP_CLOCK_HI registers.
This patch provides support for new timestamp format.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Rakesh Babu Saladi <rsaladi2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PTP hardware block can be configured to utilize
the external clock. Also the current ptp timestamp
can be captured when external trigger is applied on
a gpio pin. These features are required in scenarios
like connecting a external timing device to the chip
for time synchronization. The timing device provides
the clock and trigger(PPS signal) to the PTP block.
This patch does the following:
1. configures PTP block to use external clock
frequency and timestamp capture on external event.
2. sends PTP_REQ_EXTTS events to kernel ptp phc susbsytem
with captured timestamps
3. aligns PPS edge to adjusted ptp clock in the ptp device
by setting the PPS_THRESH to the reminder of the last
timestamp value captured by external PPS
Signed-off-by: Yi Guo <yig@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The input clock frequency of PTP block is figured
out from hardware reset block currently. The firmware
data already has this info in sclk. Hence simplify
ptp driver to use sclk from firmware data.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed inconsistent license text across the RVU admin
function driver.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Precision Timestamping block found on Octeontx2
platform is an independent coprocessor and has
internal PTP hardware clock. Once configured PTP
runs independently and when a packet arrives
CGX hardware block gets the current timestamp
from PTP block and forwards the packet to NIX
by prepending timestamp to the packet.
This patch adds the pci driver for PTP block.
The driver gets registered by AF driver and does
initial configuration and exposes a mailbox function to
read and adjust PTP hardware clock. The mailbox function
is called by AF consumers like netdev drivers or
userspace drivers. Since PTP being a single block
in platform this driver helps in accessing PTP
block by any AF consumer.
Co-developed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
