| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is occasional suspend error from e1000e which blocks the
system from further suspending. And the issue was found on
a WhiskeyLake-U platform with I219-V:
[ 20.078957] PM: pci_pm_suspend(): e1000e_pm_suspend+0x0/0x780 [e1000e] returns -2
[ 20.078970] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x170 returns -2
[ 20.078974] e1000e 0000:00:1f.6: PM: pci_pm_suspend+0x0/0x170 returned -2 after 371012 usecs
[ 20.078978] e1000e 0000:00:1f.6: PM: failed to suspend async: error -2
According to the code flow, this might be caused by broken MDI read/write
to PHY registers. However currently the code does not tell us which
register is broken. Thus enhance the debug information to print the
offender PHY register. So the next the issue is reproduced, this
information could be used for narrow down.
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220308172030.451566-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TC flower does not support matching on user specified
outer MAC address for tunnels. For ADQ tunnels, the driver
adds outer destination MAC address as lower netdev's
active unicast MAC address to filter out packets with
unrelated MAC address being delivered to ADQ VSIs.
Example:
- create tunnel device
ip l add $VXLAN_DEV type vxlan id $VXLAN_VNI dstport $VXLAN_PORT \
dev $PF
- add TC filter (in ADQ mode)
$tc filter add dev $VXLAN_DEV protocol ip parent ffff: flower \
dst_ip $INNER_DST_IP ip_proto tcp dst_port $INNER_DST_PORT \
enc_key_id $VXLAN_VNI hw_tc $ADQ_TC
Note: Filters with wild-card tunnel ID (when user does not
specify tunnel key) are also supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 9610bd988df9 ("ice: optimize XDP_TX workloads") introduced Tx IRQ
cleaning routine dedicated for XDP rings. Currently it is impossible to
call ice_clean_tx_irq() against XDP ring, so it is safe to drop
ice_ring_is_xdp() calls in there.
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In the case where the link is owned by manageability, the firmware is
not allowed to set the link state, so an error code is returned.
This however is non-fatal and there is nothing the operator can do,
so instead of confusing the operator with messages they can do nothing
about hide this message behind the debug log level.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement callbacks to check for stats and fetch port representor stats.
Stats are taken from RX/TX ring corresponding to port representor and show
the number of bytes/packets that were not offloaded.
To see slow path stats run:
ifstat -x cpu_hits -a
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Enable support for adding TC rules that filter on the inner
EtherType field of tunneled packet headers.
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Change curr_link_speed advertised speed, due to
link_info.link_speed is not equal phy.curr_user_speed_req.
Without this patch it is impossible to set advertised
speed to same as link_speed.
Testing Hints: Try to set advertised speed
to 25G only with 25G default link (use ethtool -s 0x80000000)
Fixes: 48cb27f2fd18 ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_misc_intr() is an irq handler. It should not sleep.
Use GFP_ATOMIC instead of GFP_KERNEL when allocating some memory.
Fixes: 348048e724a0 ("ice: Implement iidc operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a bonded interface is destroyed, .ndo_change_mtu can be called
during the tear-down process while the RTNL lock is held. This is a
problem since the auxiliary driver linked to the LAN driver needs to be
notified of the MTU change, and this requires grabbing a device_lock on
the auxiliary_device's dev. Currently this is being attempted in the
same execution context as the call to .ndo_change_mtu which is causing a
dead-lock.
Move the notification of the changed MTU to a separate execution context
(watchdog service task) and eliminate the "before" notification.
Fixes: 348048e724a0e ("ice: Implement iidc operations")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_vc_send_msg_to_vf function has logic to detect "failure"
responses being sent to a VF. If a VF is sent more than
ICE_DFLT_NUM_INVAL_MSGS_ALLOWED then the VF is marked as disabled.
Almost identical logic also existed in the i40e driver.
This logic was added to the ice driver in commit 1071a8358a28 ("ice:
Implement virtchnl commands for AVF support") which itself copied from
the i40e implementation in commit 5c3c48ac6bf5 ("i40e: implement virtual
device interface").
Neither commit provides a proper explanation or justification of the
check. In fact, later commits to i40e changed the logic to allow
bypassing the check in some specific instances.
The "logic" for this seems to be that error responses somehow indicate a
malicious VF. This is not really true. The PF might be sending an error
for any number of reasons such as lack of resources, etc.
Additionally, this causes the PF to log an info message for every failed
VF response which may confuse users, and can spam the kernel log.
This behavior is not documented as part of any requirement for our
products and other operating system drivers such as the FreeBSD
implementation of our drivers do not include this type of check.
In fact, the change from dev_err to dev_info in i40e commit 18b7af57d9c1
("i40e: Lower some message levels") explains that these messages
typically don't actually indicate a real issue. It is quite likely that
a user who hits this in practice will be very confused as the VF will be
disabled without an obvious way to recover.
We already have robust malicious driver detection logic using actual
hardware detection mechanisms that detect and prevent invalid device
usage. Remove the logic since its not a documented requirement and the
behavior is not intuitive.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The i40e_vc_send_msg_to_vf_ex (and its wrapper i40e_vc_send_msg_to_vf)
function has logic to detect "failure" responses sent to the VF. If a VF
is sent more than I40E_DEFAULT_NUM_INVALID_MSGS_ALLOWED, then the VF is
marked as disabled. In either case, a dev_info message is printed
stating that a VF opcode failed.
This logic originates from the early implementation of VF support in
commit 5c3c48ac6bf5 ("i40e: implement virtual device interface").
That commit did not go far enough. The "logic" for this behavior seems
to be that error responses somehow indicate a malicious VF. This is not
really true. The PF might be sending an error for any number of reasons
such as lacking resources, an unsupported operation, etc. This does not
indicate a malicious VF. We already have a separate robust malicious VF
detection which relies on hardware logic to detect and prevent a variety
of behaviors.
There is no justification for this behavior in the original
implementation. In fact, a later commit 18b7af57d9c1 ("i40e: Lower some
message levels") reduced the opcode failure message from a dev_err to a
dev_info. In addition, recent commit 01cbf50877e6 ("i40e: Fix to not
show opcode msg on unsuccessful VF MAC change") changed the logic to
allow quieting it for expected failures.
That commit prevented this logic from kicking in for specific
circumstances. This change did not go far enough. The behavior is not
documented nor is it part of any requirement for our products. Other
operating systems such as the FreeBSD implementation of our driver do
not include this logic.
It is clear this check does not make sense, and causes problems which
led to ugly workarounds.
Fix this by just removing the entire logic and the need for the
i40e_vc_send_msg_to_vf_ex function.
Fixes: 01cbf50877e6 ("i40e: Fix to not show opcode msg on unsuccessful VF MAC change")
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In some cases overloaded flag IAVF_FLAG_REINIT_ITR_NEEDED
which should indicate that interrupts need to be completely
reinitialized during reset leads to RTNL deadlocks using ethtool -C
while a reset is in progress.
To fix, it was added a new flag IAVF_FLAG_REINIT_MSIX_NEEDED
used to trigger MSI-X reinit.
New combined setting is fixed adopt after VF reset.
This has been implemented by call reinit interrupt scheme
during VF reset.
Without this fix new combined setting has never been adopted.
Fixes: 209f2f9c7181 ("iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 negotiation")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Modify netdev->features for vlan stripping based on virtual
channel messages received from the PF. Change is needed
to synchronize vlan strip status between PF sysfs and iavf ethtool.
Fixes: 5951a2b9812d ("iavf: Fix VLAN feature flags after VFR")
Signed-off-by: Norbert Ciosek <norbertx.ciosek@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add possibility to disable link state if it is administratively
disabled in PF.
It is part of the general functionality that allows the PF driver
to control the state of the virtual link VF devices.
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The 82599 PF driver disable VF driver after a special MDD event occurs.
Adds the option for administrators to control whether VFs are
automatically disabled after several MDD events.
The automatically disabling is now the default mode for 82599 PF driver,
as it is more reliable.
This addresses CVE-2021-33061.
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add support for ndo_set_vf_link_state the Network Device Option that
allows the PF driver to control the virtual link state of the VF devices.
Without this change a VF cannot be disabled/enabled by the administrator.
In the implementation the auto state takes over PF link state to
VF link setting, the enable state is not supported, the disable state
shut off the VF link regardless of the PF setting.
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Pragma unroll was introduced around GCC 8, whereas current xsk code in
ice that prepares loop_unrolled_for macro that is based on mentioned
pragma, compares GCC version against 4, which is wrong and Stephen
found this out by compiling kernel with GCC 5.4 [0].
Fix this mistake and check if GCC version is >= 8.
[0]: https://lore.kernel.org/netdev/20220307213659.47658125@canb.auug.org.au/
Fixes: 126cdfe1007a ("ice: xsk: Improve AF_XDP ZC Tx and use batching API")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20220307231353.56638-1-maciej.fijalkowski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-03-03
Jacob Keller says:
This series refactors the ice networking driver VF storage from a simple
static array to a hash table. It also introduces krefs and proper locking
and protection to prevent common use-after-free and concurrency issues.
There are two motivations for this work. First is to make the ice driver
more resilient by preventing a whole class of use-after-free bugs that can
occur around concurrent access to VF structures while removing VFs.
The second is to prepare the ice driver for future virtualization work to
support Scalable IOV, an alternative VF implementation compared to Single
Root IOV. The new VF implementation will allow for more dynamic VF creation
and removal, necessitating a more robust implementation for VF storage that
can't rely on the existing mechanisms to prevent concurrent access
violations.
The first few patches are cleanup and preparatory work needed to make the
conversion to the hash table safe. Following this preparatory work is a
patch to migrate the VF structures and variables to a new sub-structure for
code clarity. Next introduce new interface functions to abstract the VF
storage. Finally, the driver is actually converted to the hash table and
kref implementation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ice driver stores VF structures in a simple array which is allocated
once at the time of VF creation. The VF structures are then accessed
from the array by their VF ID. The ID must be between 0 and the number
of allocated VFs.
Multiple threads can access this table:
* .ndo operations such as .ndo_get_vf_cfg or .ndo_set_vf_trust
* interrupts, such as due to messages from the VF using the virtchnl
communication
* processing such as device reset
* commands to add or remove VFs
The current implementation does not keep track of when all threads are
done operating on a VF and can potentially result in use-after-free
issues caused by one thread accessing a VF structure after it has been
released when removing VFs. Some of these are prevented with various
state flags and checks.
In addition, this structure is quite static and does not support a
planned future where virtualization can be more dynamic. As we begin to
look at supporting Scalable IOV with the ice driver (as opposed to just
supporting Single Root IOV), this structure is not sufficient.
In the future, VFs will be able to be added and removed individually and
dynamically.
To allow for this, and to better protect against a whole class of
use-after-free bugs, replace the VF storage with a combination of a hash
table and krefs to reference track all of the accesses to VFs through
the hash table.
A hash table still allows efficient look up of the VF given its ID, but
also allows adding and removing VFs. It does not require contiguous VF
IDs.
The use of krefs allows the cleanup of the VF memory to be delayed until
after all threads have released their reference (by calling ice_put_vf).
To prevent corruption of the hash table, a combination of RCU and the
mutex table_lock are used. Addition and removal from the hash table use
the RCU-aware hash macros. This allows simple read-only look ups that
iterate to locate a single VF can be fast using RCU. Accesses which
modify the hash table, or which can't take RCU because they sleep, will
hold the mutex lock.
By using this design, we have a stronger guarantee that the VF structure
can't be released until after all threads are finished operating on it.
We also pave the way for the more dynamic Scalable IOV implementation in
the future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
net/batman-adv/hard-interface.c
commit 690bb6fb64f5 ("batman-adv: Request iflink once in batadv-on-batadv check")
commit 6ee3c393eeb7 ("batman-adv: Demote batadv-on-batadv skip error message")
https://lore.kernel.org/all/20220302163049.101957-1-sw@simonwunderlich.de/
net/smc/af_smc.c
commit 4d08b7b57ece ("net/smc: Fix cleanup when register ULP fails")
commit 462791bbfa35 ("net/smc: add sysctl interface for SMC")
https://lore.kernel.org/all/20220302112209.355def40@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before we switch the VF data structure storage mechanism to a hash,
introduce new accessor functions to define the new interface.
* ice_get_vf_by_id is a function used to obtain a reference to a VF from
the table based on its VF ID
* ice_has_vfs is used to quickly check if any VFs are configured
* ice_get_num_vfs is used to get an exact count of how many VFs are
configured
We can drop the old ice_validate_vf_id function, since every caller was
just going to immediately access the VF table to get a reference
anyways. This way we simply use the single ice_get_vf_by_id to both
validate the VF ID is within range and that there exists a VF with that
ID.
This change enables us to more easily convert the codebase to the hash
table since most callers now properly use the interface.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We maintain a number of values for VFs within the ice_pf structure. This
includes the VF table, the number of allocated VFs, the maximum number
of supported SR-IOV VFs, the number of queue pairs per VF, the number of
MSI-X vectors per VF, and a bitmap of the VFs with detected MDD events.
We're about to add a few more variables to this list. Clean this up
first by extracting these members out into a new ice_vfs structure
defined in ice_virtchnl_pf.h
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_for_each_vf macro is intended to be used to loop over all VFs.
The current implementation relies on an iterator that is the index into
the VF array in the PF structure. This forces all users to perform a
look up themselves.
This abstraction forces a lot of duplicate work on callers and leaks the
interface implementation to the caller. Replace this with an
implementation that includes the VF pointer the primary iterator. This
version simplifies callers which just want to iterate over every VF, as
they no longer need to perform their own lookup.
The "i" iterator value is replaced with a new unsigned int "bkt"
parameter, as this will match the necessary interface for replacing
the VF array with a hash table. For now, the bkt is the VF ID, but in
the future it will simply be the hash bucket index. Document that it
should not be treated as a VF ID.
This change aims to simplify switching from the array to a hash table. I
considered alternative implementations such as an xarray but decided
that the hash table was the simplest and most suitable implementation. I
also looked at methods to hide the bkt iterator entirely, but I couldn't
come up with a feasible solution that worked for hash table iterators.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When removing VFs, the driver takes a weird approach of assigning
pf->num_alloc_vfs to 0 before iterating over the VFs using a temporary
variable.
This logic has been in the driver for a long time, and seems to have
been carried forward from i40e.
We want to refactor the way VFs are stored, and iterating over the data
structure without the ice_for_each_vf interface impedes this work.
The logic relies on implicitly using the num_alloc_vfs as a sort of
"safe guard" for accessing VF data.
While this sort of guard makes sense for Single Root IOV where all VFs
are added at once, the data structures don't work for VFs which can be
added and removed dynamically. We also have a separate state flag,
ICE_VF_DEINIT_IN_PROGRESS which is a stronger protection against
concurrent removal and access.
Avoid the custom tmp iteration and replace it with the standard
ice_for_each_vf iterator. Delay the assignment of num_alloc_vfs until
after this loop finishes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_vc_send_msg_to_vf function is used by the PF to send a response
to a VF. This function has overzealous checks to ensure its not passed a
NULL VF pointer and to ensure that the passed in struct ice_vf has a
valid vf_id sub-member.
These checks have existed since commit 1071a8358a28 ("ice: Implement
virtchnl commands for AVF support") and function as simple sanity
checks.
We are planning to refactor the ice driver to use a hash table along
with appropriate locks in a future refactor. This change will modify how
the ice_validate_vf_id function works. Instead of a simple >= check to
ensure the VF ID is between some range, it will check the hash table to
see if the specified VF ID is actually in the table. This requires that
the function properly lock the table to prevent race conditions.
The checks may seem ok at first glance, but they don't really provide
much benefit.
In order for ice_vc_send_msg_to_vf to have these checks fail, the
callers must either (1) pass NULL as the VF, (2) construct an invalid VF
pointer manually, or (3) be using a VF pointer which becomes invalid
after they obtain it properly using ice_get_vf_by_id.
For (1), a cursory glance over callers of ice_vc_send_msg_to_vf can show
that in most cases the functions already operate assuming their VF
pointer is valid, such as by derferencing vf->pf or other members.
They obtain the VF pointer by accessing the VF array using the VF ID,
which can never produce a NULL value (since its a simple address
operation on the array it will not be NULL.
The sole exception for (1) is that ice_vc_process_vf_msg will forward a
NULL VF pointer to this function as part of its goto error handler
logic. This requires some minor cleanup to simply exit immediately when
an invalid VF ID is detected (Rather than use the same error flow as
the rest of the function).
For (2), it is unexpected for a flow to construct a VF pointer manually
instead of accessing the VF array. Defending against this is likely to
just hide bad programming.
For (3), it is definitely true that VF pointers could become invalid,
for example if a thread is processing a VF message while the VF gets
removed. However, the correct solution is not to add additional checks
like this which do not guarantee to prevent the race. Instead we plan to
solve the root of the problem by preventing the possibility entirely.
This solution will require the change to a hash table with proper
locking and reference counts of the VF structures. When this is done,
ice_validate_vf_id will require locking of the hash table. This will be
problematic because all of the callers of ice_vc_send_msg_to_vf will
already have to take the lock to obtain the VF pointer anyways. With a
mutex, this leads to a double lock that could hang the kernel thread.
Avoid this by removing the checks which don't provide much value, so
that we can safely add the necessary protections properly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After removing all VFs, the driver clears the VFLR indication for VFs.
This has been in ice since the beginning of SR-IOV support in the ice
driver.
The implementation was copied from i40e, and the motivation for the VFLR
indication clearing is described in the commit f7414531a0cf ("i40e:
acknowledge VFLR when disabling SR-IOV")
The commit explains that we need to clear the VFLR indication because
the virtual function undergoes a VFLR event. If we don't indicate that
it is complete it can cause an issue when VFs are re-enabled due to
a "phantom" VFLR.
The register block read was added under a pci_vfs_assigned check
originally. This was done because we added the check after calling
pci_disable_sriov. This was later moved to disable SRIOV earlier in the
flow so that the VF drivers could be torn down before we removed
functionality.
Move the VFLR acknowledge into the main loop that tears down VF
resources. This avoids using the tmp value for iterating over VFs
multiple times. The result will make it easier to refactor the VF array
in a future change.
It's possible we might want to modify this flow to also stop checking
pci_vfs_assigned. However, it seems reasonable to keep this change: we
should only clear the VFLR if we actually disabled SR-IOV.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_mbx_clear_malvf function is used to clear the indication and
count of how many times a VF was detected as malicious. During
ice_free_vfs, we use this function to ensure that all removed VFs are
reset to a clean state.
The call currently is done at the end of ice_free_vfs() using a tmp
value to iterate over all of the entries in the bitmap.
This separate iteration using tmp is problematic for a planned refactor
of the VF array data structure. To avoid this, lets move the call
slightly higher into the function inside the loop where we teardown all
of the VFs. This avoids one use of the tmp value used for iteration.
We'll fix the other user in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We are planning to replace the simple array structure tracking VFs with
a hash table. This change will also remove the "num_alloc_vfs" variable.
Instead, new access functions to use the hash table as the source of
truth will be introduced. These will generally be equivalent to existing
checks, except during VF initialization.
Specifically, ice_set_per_vf_res() cannot use the hash table as it will
be operating prior to VF structures being inserted into the hash table.
Instead of using pf->num_alloc_vfs, simply pass the num_vfs value in
from the caller.
Note that a sub-function of ice_set_per_vf_res, ice_determine_res, also
implicitly depends on pf->num_alloc_vfs. Replace ice_determine_res with
a simpler inline implementation based on rounddown_pow_of_two. Note that
we must explicitly check that the argument is non-zero since it does not
play well with zero as a value.
Instead of using the function and while loop, simply calculate the
number of queues we have available by dividing by num_vfs. Check if the
desired queues are available. If not, round down to the nearest power of
2 that fits within our available queues.
This matches the behavior of ice_determine_res but is easier to follow
as simple in-line logic. Remove ice_determine_res entirely.
With this change, we no longer depend on the pf->num_alloc_vfs during
the initialization phase of VFs. This will allow us to safely remove it
in a future planned refactor of the VF data structures.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The VSI structure contains a vf_id field used to associate a VSI with a
VF. This is used mainly for ICE_VSI_VF as well as partially for
ICE_VSI_CTRL associated with the VFs.
This API was designed with the idea that VFs are stored in a simple
array that was expected to be static throughout most of the driver's
life.
We plan on refactoring VF storage in a few key ways:
1) converting from a simple static array to a hash table
2) using krefs to track VF references obtained from the hash table
3) use RCU to delay release of VF memory until after all references
are dropped
This is motivated by the goal to ensure that the lifetime of VF
structures is accounted for, and prevent various use-after-free bugs.
With the existing vsi->vf_id, the reference tracking for VFs would
become somewhat convoluted, because each VSI maintains a vf_id field
which will then require performing a look up. This means all these flows
will require reference tracking and proper usage of rcu_read_lock, etc.
We know that the VF VSI will always be backed by a valid VF structure,
because the VSI is created during VF initialization and removed before
the VF is destroyed. Rely on this and store a reference to the VF in the
VSI structure instead of storing a VF ID. This will simplify the usage
and avoid the need to perform lookups on the hash table in the future.
For ICE_VSI_VF, it is expected that vsi->vf is always non-NULL after
ice_vsi_alloc succeeds. Because of this, use WARN_ON when checking if a
vsi->vf pointer is valid when dealing with VF VSIs. This will aid in
debugging code which violates this assumption and avoid more disastrous
panics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The code for supporting eswitch mode and port representors on VFs uses
an unwind based cleanup flow when handling errors.
These flows are used to cleanup and get everything back to the state
prior to attempting to switch from legacy to representor mode or back.
The unwind iterations make sense, but complicate a plan to refactor the
VF array structure. In the future we won't have a clean method of
reversing an iteration of the VFs.
Instead, we can change the cleanup flow to just iterate over all VF
structures and clean up appropriately.
First notice that ice_repr_add_for_all_vfs and ice_repr_rem_from_all_vfs
have an additional step of re-assigning the VC ops. There is no good
reason to do this outside of ice_repr_add and ice_repr_rem. It can
simply be done as the last step of these functions.
Second, make sure ice_repr_rem is safe to call on a VF which does not
have a representor. Check if vf->repr is NULL first and exit early if
so.
Move ice_repr_rem_from_all_vfs above ice_repr_add_for_all_vfs so that we
can call it from the cleanup function.
In ice_eswitch.c, replace the unwind iteration with a call to
ice_eswitch_release_reprs. This will go through all of the VFs and
revert the VF back to the standard model without the eswitch mode.
To make this safe, ensure this function checks whether or not the
represent or has been moved. Rely on the metadata destination in
vf->repr->dst. This must be NULL if the representor has not been moved
to eswitch mode.
Ensure that we always re-assign this value back to NULL after freeing
it, and move the ice_eswitch_release_reprs so that it can be called from
the setup function.
With these changes, eswitch cleanup no longer uses an unwind flow that
is problematic for the planned VF data structure change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit c685c69fba71 ("ixgbe: don't do any AF_XDP zero-copy transmit if
netif is not OK") addressed the ring transient state when
MEM_TYPE_XSK_BUFF_POOL was being configured which in turn caused the
interface to through down/up. Maurice reported that when carrier is not
ok and xsk_pool is present on ring pair, ksoftirqd will consume 100% CPU
cycles due to the constant NAPI rescheduling as ixgbe_poll() states that
there is still some work to be done.
To fix this, do not set work_done to false for a !netif_carrier_ok().
Fixes: c685c69fba71 ("ixgbe: don't do any AF_XDP zero-copy transmit if netif is not OK")
Reported-by: Maurice Baijens <maurice.baijens@ellips.com>
Tested-by: Maurice Baijens <maurice.baijens@ellips.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new ice_gnss.c file for holding the basic GNSS module functions.
If the device supports GNSS module, call the new ice_gnss_init and
ice_gnss_release functions where appropriate.
Implement basic functionality for reading the data from GNSS module
using TTY device.
Add I2C read AQ command. It is now required for controlling the external
physical connectors via external I2C port expander on E810-T adapters.
Future changes will introduce write functionality.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Sudhansu Sekhar Mishra <sudhansu.mishra@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove non-inclusive language from the iavf driver.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently there are functions in iavf_virtchnl.c for polling specific
virtchnl receive events. These are all assigning iavf_status values to
int values. Fix this and explicitly assign int values if iavf_status
is not IAVF_SUCCESS.
Also, refactor a small amount of duplicated code that can be reused by
all of the previously mentioned functions.
Finally, fix some spacing errors for variable assignment and get rid of
all the goto statements in the refactored functions for clarity.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Several functions in the iAVF core files take status values of the enum
iavf_status and convert them into integer values. This leads to
confusion as functions return both Linux errno values and status codes
intermixed. Reporting status codes as if they were "errno" values can
lead to confusion when reviewing error logs. Additionally, it can lead
to unexpected behavior if a return value is not interpreted properly.
Fix this by introducing iavf_status_to_errno, a switch that explicitly
converts from the status codes into an appropriate error value. Also
introduce a virtchnl_status_to_errno function for the one case where we
were returning both virtchnl status codes and iavf_status codes in the
same function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Return value directly instead of taking this in another redundant
variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use new type field of VIRTCHNL_OP_ADD_ETH_ADDR and
VIRTCHNL_OP_DEL_ETH_ADDR requests to indicate that
VF wants to change its default MAC address.
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In order to handle the capability exchange necessary for
VIRTCHNL_VF_OFFLOAD_VLAN_V2, the driver must send
a VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS message. This must occur prior to
__IAVF_CONFIG_ADAPTER, and the driver must wait for the response from
the PF.
To handle this, the __IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS state was
introduced. This state is intended to process the response from the VLAN
V2 caps message. This works ok, but is difficult to extend to adding
more extended capability exchange.
Existing (and future) AVF features are relying more and more on these
sort of extended ops for processing additional capabilities. Just like
VLAN V2, this exchange must happen prior to __IAVF_CONFIG_ADPATER.
Since we only send one outstanding AQ message at a time during init, it
is not clear where to place this state. Adding more capability specific
states becomes a mess. Instead of having the "previous" state send
a message and then transition into a capability-specific state,
introduce __IAVF_EXTENDED_CAPS state. This state will use a list of
extended_caps that determines what messages to send and receive. As long
as there are extended_caps bits still set, the driver will remain in
this state performing one send or one receive per state machine loop.
Refactor the VLAN V2 negotiation to use this new state, and remove the
capability-specific state. This makes it significantly easier to add
a new similar capability exchange going forward.
Extended capabilities are processed by having an associated SEND and
RECV extended capability bit. During __IAVF_EXTENDED_CAPS, the
driver checks these bits in order by feature, first the send bit for
a feature, then the recv bit for a feature. Each send flag will call
a function that sends the necessary response, while each receive flag
will wait for the response from the PF. If a given feature can't be
negotiated with the PF, the associated flags will be cleared in
order to skip processing of that feature.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Advanced link speed support was added long back, but adding AIM support was
missed. This patch adds AIM support for advanced link speed support, which
allows the algorithm to take into account 50G/100G link speeds. Also, other
previous speeds are taken into consideration when advanced link speeds are
supported.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Update MAC type check e1000_pch_tgp because for e1000_pch_cnp,
NVM checksum update is still possible.
Emit a more detailed warning message.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=1191663
Fixes: 4051f68318ca ("e1000e: Do not take care about recovery NVM checksum")
Reported-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Disable the OEM bit/Gig Disable/restart AN impact and disable the PHY
LAN connected device (LCD) reset during power management flows. This
fixes possible HW unit hangs on the s0ix exit on some corporate ADL
platforms.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214821
Fixes: 3e55d231716e ("e1000e: Add handshake with the CSME to support S0ix")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Suggested-by: Nir Efrati <nir.efrati@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Similar to "igc_read_phy_reg_gpy: drop premature return" patch.
igc_write_phy_reg_gpy checks the return value from igc_write_phy_reg_mdic
and if it's not 0, returns immediately. By doing this, it leaves the HW
semaphore in the acquired state.
Drop this premature return statement, the function returns after
releasing the semaphore immediately anyway.
Fixes: 5586838fe9ce ("igc: Add code for PHY support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reported-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
igc_read_phy_reg_gpy checks the return value from igc_read_phy_reg_mdic
and if it's not 0, returns immediately. By doing this, it leaves the HW
semaphore in the acquired state.
Drop this premature return statement, the function returns after
releasing the semaphore immediately anyway.
Fixes: 5586838fe9ce ("igc: Add code for PHY support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The setup of __IAVF_RESETTING state in watchdog task had no
effect and could lead to slow resets in the driver as
the task for __IAVF_RESETTING state only requeues watchdog.
Till now the __IAVF_RESETTING was interpreted by reset task
as running state which could lead to errors with allocating
and resources disposal.
Make watchdog_task queue the reset task when it's necessary.
Do not update the state to __IAVF_RESETTING so the reset task
knows exactly what is the current state of the adapter.
Fixes: 898ef1cb1cb2 ("iavf: Combine init and watchdog state machines")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver was queueing reset_task regardless of the netdev
state.
Do not queue the reset task in iavf_change_mtu if netdev
is not running.
Fixes: fdd4044ffdc8 ("iavf: Remove timer for work triggering, use delaying work instead")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There exists a missing mutex_unlock call on crit_lock in
iavf_reset_task call path.
Unlock the crit_lock before returning from reset task.
Fixes: 5ac49f3c2702 ("iavf: use mutexes for locking of critical sections")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When iavf_init_version_check sends VIRTCHNL_OP_GET_VF_RESOURCES
message, the driver will wait for the response after requeueing
the watchdog task in iavf_init_get_resources call stack. The
logic is implemented this way that iavf_init_get_resources has
to be called in order to allocate adapter->vf_res. It is polling
for the AQ response in iavf_get_vf_config function. Expect a
call trace from kernel when adminq_task worker handles this
message first. adapter->vf_res will be NULL in
iavf_virtchnl_completion.
Make the watchdog task not queue the adminq_task if the init
process is not finished yet.
Fixes: 898ef1cb1cb2 ("iavf: Combine init and watchdog state machines")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
iavf_virtchnl_completion is called under crit_lock but when
the code for VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is called,
this lock is released in order to obtain rtnl_lock to avoid
ABBA deadlock with unregister_netdev.
Along with the new way iavf_remove behaves, there exist
many risks related to the lock release and attmepts to regrab
it. The driver faces crashes related to races between
unregister_netdev and netdev_update_features. Yet another
risk is that the driver could already obtain the crit_lock
in order to destroy it and iavf_virtchnl_completion could
crash or block forever.
Make iavf_virtchnl_completion never relock crit_lock in it's
call paths.
Extract rtnl_lock locking logic to the driver for
unregister_netdev in order to set the netdev_registered flag
inside the lock.
Introduce a new flag that will inform adminq_task to perform
the code from VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS right after
it finishes processing messages. Guard this code with remove
flags so it's never called when the driver is in remove state.
Fixes: 5951a2b9812d ("iavf: Fix VLAN feature flags after VFR")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When init states of the adapter work, the errors like lack
of communication with the PF might hop in. If such events
occur the driver restores previous states in order to retry
initialization in a proper way. When remove task kicks in,
this situation could lead to races with unregistering the
netdevice as well as resources cleanup. With the commit
introducing the waiting in remove for init to complete,
this problem turns into an endless waiting if init never
recovers from errors.
Introduce __IAVF_IN_REMOVE_TASK bit to indicate that the
remove thread has started.
Make __IAVF_COMM_FAILED adapter state respect the
__IAVF_IN_REMOVE_TASK bit and set the __IAVF_INIT_FAILED
state and return without any action instead of trying to
recover.
Make __IAVF_INIT_FAILED adapter state respect the
__IAVF_IN_REMOVE_TASK bit and return without any further
actions.
Make the loop in the remove handler break when adapter has
__IAVF_INIT_FAILED state set.
Fixes: 898ef1cb1cb2 ("iavf: Combine init and watchdog state machines")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There exist races when port is being configured and remove is
triggered.
unregister_netdev is not and can't be called under crit_lock
mutex since it is calling ndo_stop -> iavf_close which requires
this lock. Depending on init state the netdev could be still
unregistered so unregister_netdev never cleans up, when shortly
after that the device could become registered.
Make iavf_remove wait until port finishes initialization.
All critical state changes are atomic (under crit_lock).
Crashes that come from iavf_reset_interrupt_capability and
iavf_free_traffic_irqs should now be solved in a graceful
manner.
Fixes: 605ca7c5c6707 ("iavf: Fix kernel BUG in free_msi_irqs")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
