summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/intel/igc
AgeCommit message (Collapse)AuthorFilesLines
2020-09-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2-12/+27
Two minor conflicts: 1) net/ipv4/route.c, adding a new local variable while moving another local variable and removing it's initial assignment. 2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes. One pretty prints the port mode differently, whilst another changes the driver to try and obtain the port mode from the port node rather than the switch node. Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09igc: Fix not considering the TX delay for timestampsVinicius Costa Gomes1-0/+19
When timestamping a packet there's a delay between the start of the packet and the point where the hardware actually captures the timestamp. This difference needs to be considered if we want accurate timestamps. This was done on the RX side, but not on the TX side. Fixes: 2c344ae24501 ("igc: Add support for TX timestamping") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-09-09igc: Fix wrong timestamp latency numbersVinicius Costa Gomes1-12/+8
The previous timestamping latency numbers were obtained by interpolating the i210 numbers with the i225 crystal clock value. That calculation was wrong. Use the correct values from real measurements. Fixes: 81b055205e8b ("igc: Add support for RX timestamping") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-08-26net: Take common prefetch code structure into a functionTariq Toukan1-8/+2
Many device drivers use the same prefetch code structure to deal with small L1 cacheline size. Take this code into a function and call it from the drivers. Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-14igc: Fix PTP initializationVinicius Costa Gomes2-5/+2
Right now, igc_ptp_reset() is called from igc_reset(), which is called from igc_probe() before igc_ptp_init() has a chance to run. It is detected as an attempt to use an spinlock without registering its key first. See log below. To avoid this problem, simplify the initialization: igc_ptp_init() is only called from igc_probe(), and igc_ptp_reset() is only called from igc_reset(). [ 2.736332] INFO: trying to register non-static key. [ 2.736902] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input10 [ 2.737513] the code is fine but needs lockdep annotation. [ 2.737513] turning off the locking correctness validator. [ 2.737515] CPU: 8 PID: 239 Comm: systemd-udevd Tainted: G E 5.8.0-rc7+ #13 [ 2.737515] Hardware name: Gigabyte Technology Co., Ltd. Z390 AORUS ULTRA/Z390 AORUS ULTRA-CF, BIOS F7 03/14/2019 [ 2.737516] Call Trace: [ 2.737521] dump_stack+0x78/0xa0 [ 2.737524] register_lock_class+0x6b1/0x6f0 [ 2.737526] ? lockdep_hardirqs_on_prepare+0xca/0x160 [ 2.739177] ? _raw_spin_unlock_irq+0x24/0x50 [ 2.739179] ? trace_hardirqs_on+0x1c/0xf0 [ 2.740820] __lock_acquire+0x56/0x1ff0 [ 2.740823] ? __schedule+0x30c/0x970 [ 2.740825] lock_acquire+0x97/0x3e0 [ 2.740830] ? igc_ptp_reset+0x35/0xf0 [igc] [ 2.740833] ? schedule_hrtimeout_range_clock+0xb7/0x120 [ 2.742507] _raw_spin_lock_irqsave+0x3a/0x50 [ 2.742512] ? igc_ptp_reset+0x35/0xf0 [igc] [ 2.742515] igc_ptp_reset+0x35/0xf0 [igc] [ 2.742519] igc_reset+0x96/0xd0 [igc] [ 2.744148] igc_probe+0x68f/0x7d0 [igc] [ 2.745796] local_pci_probe+0x3d/0x70 [ 2.745799] pci_device_probe+0xd1/0x190 [ 2.745802] really_probe+0x15a/0x3f0 [ 2.759936] driver_probe_device+0xe1/0x150 [ 2.759937] device_driver_attach+0xa8/0xb0 [ 2.761786] __driver_attach+0x89/0x150 [ 2.761786] ? device_driver_attach+0xb0/0xb0 [ 2.761787] ? device_driver_attach+0xb0/0xb0 [ 2.761788] bus_for_each_dev+0x66/0x90 [ 2.765012] bus_add_driver+0x12e/0x1f0 [ 2.765716] driver_register+0x8b/0xe0 [ 2.766418] ? 0xffffffffc0230000 [ 2.767119] do_one_initcall+0x5a/0x310 [ 2.767826] ? kmem_cache_alloc_trace+0xe9/0x200 [ 2.768528] do_init_module+0x5c/0x260 [ 2.769206] __do_sys_finit_module+0x93/0xe0 [ 2.770048] do_syscall_64+0x46/0xa0 [ 2.770716] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 2.771396] RIP: 0033:0x7f83534589e0 [ 2.772073] Code: 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 2e 2e 2e 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 80 24 0d 00 f7 d8 64 89 01 48 [ 2.772074] RSP: 002b:00007ffd31d0ed18 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 [ 2.774854] RAX: ffffffffffffffda RBX: 000055d52816aba0 RCX: 00007f83534589e0 [ 2.774855] RDX: 0000000000000000 RSI: 00007f83535b982f RDI: 0000000000000006 [ 2.774855] RBP: 00007ffd31d0ed60 R08: 0000000000000000 R09: 00007ffd31d0ed30 [ 2.774856] R10: 0000000000000006 R11: 0000000000000246 R12: 0000000000000000 [ 2.774856] R13: 0000000000020000 R14: 00007f83535b982f R15: 000055d527f5e120 Fixes: 5f2958052c58 ("igc: Add basic skeleton for PTP") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-27igc: Fix static checker warningSasha Neftin1-1/+1
drivers/net/ethernet/intel/igc/igc_mac.c:424 igc_check_for_copper_link() error: uninitialized symbol 'link'. This patch come to fix this warning and initialize the 'link' symbol. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 707abf069548 ("igc: Add initial LTR support") Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-27igc: Clean up the hw_stats structureSasha Neftin4-13/+0
Remove ictxptc, ictxatc, cbtmpc, cbrdpc, cbrmpc and htcbdpc fields from the hw_stats structure. Accordance to the i225 device specification these fields not in use. This patch come to clean up the driver code. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-27igc: Clean up the mac_info structureSasha Neftin1-5/+0
collision_delta, tx_packet_delta, txcw, adaptive_ifs and has_fwsm fields not in use. This patch come to clean up the driver code. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-27igc: Remove ledctl_ fields from the mac_info structureSasha Neftin1-3/+0
LED control currently not implemented. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-27igc: Fix registers definitionSasha Neftin4-20/+0
IGC_ICTXPTC and IGC_ICTXATC are already defined elsewhere, remove this double definition. Also, remove unneeded registers as they are not applicable to i225 devices. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-27igc: Remove unneeded ICTXQMTC registerSasha Neftin4-5/+0
Tx Queue Min Threshold Count register no applicable for the i225 device. This patch comes to clean up it. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-27igc: Add Receive Descriptor Minimum Threshold Count to clear HW countersSasha Neftin1-0/+1
The statistics of this register are being tracked, however, the register was inadvertently missed when implementing igc_clear_hw_cntrs_base(). The register is clear on read, so add it to the function so that the register is cleared when requested so the tracked count is accurate. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-27igc: Remove unneeded variableSasha Neftin4-5/+0
Though we are populating and tracking ictxqec, the value is not being used for anything so remove it altogether and save the register read. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-01ethernet/intel: Convert fallthrough code commentsJeff Kirsher2-15/+6
Convert all the remaining 'fall through" code comments to the newer 'fallthrough;' keyword. Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-06-29igc: Remove checking media type during MAC initializationSasha Neftin1-5/+3
i225 device support only copper mode. There is no point to check media type in the igc_config_fc_after_link_up() method. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Remove unneeded check for copper media typeSasha Neftin1-2/+1
PHY of the i225 device support only copper mode. There is no point to check media type in the igc_power_up_link() method. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Refactor the igc_power_down_link()Sasha Neftin1-13/+3
Currently the implementation of igc_power_down_link() method was just calling igc_power_down_phy_copper_base() method. We can just call igc_power_down_phy_copper_base() method directly. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Remove TCP segmentation TX fail counterSasha Neftin3-3/+0
TCP segmentation TX context fail counter is not applicable for i225 devices. This patch comes to clean up this counter. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown<aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Add LPI countersSasha Neftin2-0/+4
Add EEE TX LPI and EEE RX LPI counters. A EEE TX LPI event occurs when the transmitter enters EEE (IEEE 802.3az) LPI state. A EEE RX LPI event occurs when the receiver detect link partner entry into EEE(IEEE 802.3az) LPI state. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Fix Rx timestamp disablingAndre Guedes1-37/+17
When Rx timestamping is enabled, we set the timestamp bit in SRRCTL register for each queue, but we don't clear it when disabling. This patch fixes igc_ptp_disable_rx_timestamp() accordingly. Also, this patch gets rid of igc_ptp_enable_tstamp_rxqueue() and igc_ptp_enable_tstamp_all_rxqueues() and move their logic into igc_ptp_enable_rx_timestamp() to keep the enable and disable helpers symmetric. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Refactor igc_ptp_set_timestamp_mode()Andre Guedes1-50/+53
Current igc_ptp_set_timestamp_mode() logic is a bit tangled since it handles many different hardware configurations in one single place, making it harder to follow. This patch untangles that code by breaking it into helper functions. Quick note about the hw->mac.type check which was removed in this refactoring: this check it not really needed since igc_i225 is the only type supported by the IGC driver. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Remove UDP filter setup in PTP codeAndre Guedes1-50/+1
As implemented in igc_ethtool_get_ts_info(), igc only supports HWTSTAMP_ FILTER_ALL so any HWTSTAMP_FILTER_* option the user may set falls back to HWTSTAMP_FILTER_ALL. HWTSTAMP_FILTER_ALL is implemented via Rx Time Sync Control (TSYNCRXCTL) configuration which timestamps all incoming packets. Configuring a UDP filter, in addition to TSYNCRXCTL, doesn't add much so this patch removes that code. It also takes this opportunity to remove some non-applicable comments. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Check __IGC_PTP_TX_IN_PROGRESS instead of ptp_tx_skbAndre Guedes1-9/+7
The __IGC_PTP_TX_IN_PROGRESS flag indicates we have a pending Tx timestamp. In some places, instead of checking that flag, we check adapter->ptp_tx_skb. This patch fixes those places to use the flag. Quick note about igc_ptp_tx_hwtstamp() change: when that function is called, adapter->ptp_tx_skb is expected to be valid always so we WARN_ON_ONCE() in case it is not. Quick note about igc_ptp_suspend() change: when suspending, we don't really need to check if there is a pending timestamp. We can simply clear it unconditionally. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Remove duplicate code in Tx timestamp handlingAndre Guedes1-19/+15
The functions igc_ptp_tx_hang() and igc_ptp_tx_work() have duplicate code which handles Tx timestamp timeouts. This patch does a trivial refactoring by moving that code to its own function and reusing it. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Clean up Rx timestamping logicAndre Guedes5-58/+5
Differently from I210, I225 doesn't report Rx timestamps via the TS bit Rx descriptor + RXSTMPL/RXSTMPH registers mechanism. Rx timestamps are reported in the packet buffer only, which is implemented by igc_ptp_rx_ pktstamp(). So this patch removes igc_ptp_rx_rgtstamp() and all code related to it, copied from igb driver. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Add initial LTR supportSasha Neftin5-0/+139
The LTR message on the PCIe inform the requested latency on which the PCIe must become active to the downstream PCIe port of the system. This patch provide recommended LTR parameters by i225 specification. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-29igc: Add initial EEE supportSasha Neftin8-0/+189
IEEE802.3az-2010 Energy Efficient Ethernet has been approved as standard (September 2010) and the driver can enable and disable it via ethtool. Disable the feature by default on parts which support it. Add enable/disable eee options. tx-lpi, tx-timer and advertise not supported yet. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Reviewed-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-06-25net/intel: remove driver versions from Intel driversJeff Kirsher3-8/+1
As with other networking drivers, remove the unnecessary driver version from the Intel drivers. The ethtool driver information and module version will then report the kernel version instead. For ixgbe, i40e and ice drivers, the driver passes the driver version to the firmware to confirm that we are up and running. So we now pass the value of UTS_RELEASE to the firmware. This adminq call is required per the HAS document. The Device then sends an indication to the BMC that the PF driver is present. This is done using Host NC Driver Status Indication in NC-SI Get Link command or via the Host Network Controller Driver Status Change AEN. What the BMC may do with this information is implementation-dependent, but this is a standard NC-SI 1.1 command we honor per the HAS. CC: Bruce Allan <bruce.w.allan@intel.com> CC: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Alek Loktionov <aleksandr.loktionov@intel.com> CC: Kevin Liedtke <kevin.d.liedtke@intel.com> CC: Aaron Rowden <aaron.f.rowden@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Co-developed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com>
2020-06-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextLinus Torvalds16-1161/+1753
Pull networking updates from David Miller: 1) Allow setting bluetooth L2CAP modes via socket option, from Luiz Augusto von Dentz. 2) Add GSO partial support to igc, from Sasha Neftin. 3) Several cleanups and improvements to r8169 from Heiner Kallweit. 4) Add IF_OPER_TESTING link state and use it when ethtool triggers a device self-test. From Andrew Lunn. 5) Start moving away from custom driver versions, use the globally defined kernel version instead, from Leon Romanovsky. 6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin. 7) Allow hard IRQ deferral during NAPI, from Eric Dumazet. 8) Add sriov and vf support to hinic, from Luo bin. 9) Support Media Redundancy Protocol (MRP) in the bridging code, from Horatiu Vultur. 10) Support netmap in the nft_nat code, from Pablo Neira Ayuso. 11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina Dubroca. Also add ipv6 support for espintcp. 12) Lots of ReST conversions of the networking documentation, from Mauro Carvalho Chehab. 13) Support configuration of ethtool rxnfc flows in bcmgenet driver, from Doug Berger. 14) Allow to dump cgroup id and filter by it in inet_diag code, from Dmitry Yakunin. 15) Add infrastructure to export netlink attribute policies to userspace, from Johannes Berg. 16) Several optimizations to sch_fq scheduler, from Eric Dumazet. 17) Fallback to the default qdisc if qdisc init fails because otherwise a packet scheduler init failure will make a device inoperative. From Jesper Dangaard Brouer. 18) Several RISCV bpf jit optimizations, from Luke Nelson. 19) Correct the return type of the ->ndo_start_xmit() method in several drivers, it's netdev_tx_t but many drivers were using 'int'. From Yunjian Wang. 20) Add an ethtool interface for PHY master/slave config, from Oleksij Rempel. 21) Add BPF iterators, from Yonghang Song. 22) Add cable test infrastructure, including ethool interfaces, from Andrew Lunn. Marvell PHY driver is the first to support this facility. 23) Remove zero-length arrays all over, from Gustavo A. R. Silva. 24) Calculate and maintain an explicit frame size in XDP, from Jesper Dangaard Brouer. 25) Add CAP_BPF, from Alexei Starovoitov. 26) Support terse dumps in the packet scheduler, from Vlad Buslov. 27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei. 28) Add devm_register_netdev(), from Bartosz Golaszewski. 29) Minimize qdisc resets, from Cong Wang. 30) Get rid of kernel_getsockopt and kernel_setsockopt in order to eliminate set_fs/get_fs calls. From Christoph Hellwig. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits) selftests: net: ip_defrag: ignore EPERM net_failover: fixed rollback in net_failover_open() Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv" Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv" vmxnet3: allow rx flow hash ops only when rss is enabled hinic: add set_channels ethtool_ops support selftests/bpf: Add a default $(CXX) value tools/bpf: Don't use $(COMPILE.c) bpf, selftests: Use bpf_probe_read_kernel s390/bpf: Use bcr 0,%0 as tail call nop filler s390/bpf: Maintain 8-byte stack alignment selftests/bpf: Fix verifier test selftests/bpf: Fix sample_cnt shared between two threads bpf, selftests: Adapt cls_redirect to call csum_level helper bpf: Add csum_level helper for fixing up csum levels bpf: Fix up bpf_skb_adjust_room helper's skb csum setting sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf() crypto/chtls: IPv6 support for inline TLS Crypto/chcr: Fixes a coccinile check error Crypto/chcr: Fixes compilations warnings ...
2020-05-28igc: Fix wrong register nameSasha Neftin2-2/+2
Accordance to the i225 datasheet this register address used by Host Transmit Discarded Packet by MAC counter and not by not applicable Carrier Extension Error counter. This patch comes to fix this wrong definition. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-28igc: Remove Sequence Error CounterSasha Neftin3-3/+0
Accordance to the i225 datasheet sequence error counter does not applicable to the i225 device. This patch comes to clean up this counter. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-28igc: Add Receive Error CounterSasha Neftin3-0/+3
Receive error counter reflect total number of non-filtered packets received with errors. This includes: CRC error, symbol error, Rx data error and carrier extend error. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-28igc: Remove symbol error counterSasha Neftin3-3/+0
Accordance to the i225 datasheet symbol error counter does not applicable to the i225 device. This patch comes to clean up this counter. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-28igc: Fix IGC_MAX_RXNFC_RULESAndre Guedes1-1/+4
IGC supports a total of 32 rules. 16 MAC address based, 8 VLAN priority based, and 8 Ethertype based. This patch fixes IGC_MAX_RXNFC_RULES accordingly. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-28igc: Reject NFC rules with multiple matchesAndre Guedes1-5/+4
The way Rx queue assignment based on mac address, Ethertype and VLAN priority filtering operates in I225 doesn't allow us to properly support NFC rules with multiple matches. Consider the following example which assigns to queue 2 frames matching the address MACADDR *and* Ethertype ETYPE. $ ethtool -N eth0 flow-type ether dst <MACADDR> proto <ETYPE> queue 2 When such rule is applied, we have 2 unwanted behaviors: 1) Any frame matching MACADDR will be assigned to queue 2. It doesn't matter the ETYPE value. 2) Any accepted frame that has Ethertype equals to ETYPE, no matter the mac address, will be assigned to queue 2 as well. In current code, multiple-match filters are accepted by the driver, even though it doesn't support them properly. This patch adds a check for multiple-match rules in igc_ethtool_is_nfc_rule_valid() so they are rejected. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-28igc: Remove unused flagsSasha Neftin1-4/+0
Transmit underrun, late and excess collision flags not in use. This patch comes to clean up these flags. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Remove unused descriptor's flagsSasha Neftin1-4/+0
Enable Tidv register, Report Packet Sent, Report Status and Ethernet CRC flags not in use. This patch comes to clean up these flags. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Remove igc_nfc_rule_exit()Andre Guedes1-14/+0
During igc_down(), we call igc_nfc_rule_exit() which traverse the NFC rule list disabling filters one by one. Later on in igc_down() flow we issue an hardware reset which also clear all filters. Since we already reset the hardware, we don't actually need to disable each filter manually. In order to simplify the code, this patch removes igc_nfc_rule() altogether. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Change adapter->nfc_rule_lock to mutexAndre Guedes3-20/+20
This patch changes adapter->nfc_rule_lock type from spin_lock to mutex so we avoid unnecessary busy waiting on lock contention. A closer look at the execution context of NFC rule API users shows that all of them run in process context. The API users are: ethtool ops, igc_configure(), called when interface is brought up by user or reset workequeue thread, igc_down(), called when interface is brought down, and igc_remove(), called when driver is unloaded. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Change return type from igc_disable_nfc_rule()Andre Guedes1-17/+9
None of igc_disable_nfc_rule() callers actually check its returning value. A closer look at why this function would fail shows that the only situation is when we try to delete an Ethertype or MAC filter that doesn't exist. That situation is very unlikely so we can change igc_del_etype_filter() and igc_del_mac_filter() logic to "if the filter doesn't exist, we are done", and keep the logic in igc_disable_nfc_rule() callers simple. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Fix NFC rule validationAndre Guedes1-3/+4
If we try to overwrite an existing rule with the same filter but different action, we get EEXIST error as shown below. $ ethtool -N eth0 flow-type ether dst <MACADDR> action 1 loc 10 $ ethtool -N eth0 flow-type ether dst <MACADDR> action 2 loc 10 rmgr: Cannot insert RX class rule: File exists The second command is expected to overwrite the previous rule in location 10 and succeed. This patch fixes igc_ethtool_check_nfc_rule() so it also checks the rules location. In case they match, the rule under evaluation should not be considered invalid. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Fix NFC rules leak when driver is unloadedAndre Guedes1-13/+16
If we have RFC rules in adapter->nfc_rule_list when the IGC driver is unloaded, all rules are leaked. This patch fixes the issue by introducing the helper igc_flush_nfc_rules() and calling it in igc_remove(). It also updates igc_set_features() so is reuses the new helper instead of re-implementing it. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Refactor igc_ethtool_update_nfc_rule()Andre Guedes3-166/+195
Current implementation of igc_ethtool_update_nfc_rule() is a bit convoluted since it handles too many things: rule lookup, deletion and addition. This patch breaks it into three functions so we simplify the code and improve code reuse. Code related to rule lookup is refactored out to a new function called igc_get_nfc_rule(). Code related to rule addition is refactored out to a new function called igc_add_nfc_rule(). This function enables the rule in hardware and adds it to the adapter's list. Code related to rule deletion is refactored out to a new function called igc_del_nfc_rule(). This function disables the rule in hardware, removes it from adapter's list, and deletes it. As a byproduct of this refactoring, igc_enable_nfc_rule() and igc_disable_nfc_rule() are moved to igc_main.c since they are not used in igc_ethtool.c anymore, and igc_restore_nfc_rules() and igc_nfc_rule_ exit() are moved around to avoid forward declaration. Also, since this patch already touches igc_ethtool_get_nfc_rule(), it takes the opportunity to remove the 'match_flags' check. Empty flags are not allowed to be added so no need to check that. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Fix NFC rules restorationAndre Guedes3-20/+19
When network interface is brought up, the driver re-enables the NFC rules previously configured. However, this is done in reverse order the rules were added and hardware filters are configured differently. For example, consider the following rules: $ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:AA queue 0 $ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:BB queue 1 $ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:CC queue 2 $ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:DD queue 3 RAL/RAH registers are configure so filter index 1 has address ending with AA, filter index 2 has address ending in BB, and so on. If we bring the interface down and up again, RAL/RAH registers are configured so filter index 1 has address ending in DD, filter index 2 has CC, and so on. IOW, in reverse order we had before bringing the interface down. This issue can be fixed by traversing adapter->nfc_rule_list in backwards when restoring the rules. Since hlist doesn't support backwards traversal, this patch replaces it by list_head and fixes igc_restore_nfc_rules() accordingly. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Fix NFC rules with multicast addressesAndre Guedes1-6/+0
Multicast MAC addresses are valid address for NFC rules but igc_add_mac_filter() is currently rejecting them. In fact, the I225 controller doesn't impose any constraint on the address value so this patch gets rid of the address validation check in MAC filter APIs. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Fix NFC rule overwrite casesAndre Guedes1-2/+1
When the 'loc' argument is passed in ethtool, the input rule overwrites any rule present in that location. In this situation we must disable the old rule otherwise it is left enabled in hardware. This patch fixes the issue by always calling igc_disable_nfc_rule() when deleting the old rule, no matter the value of 'input' argument. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Fix locking issue when retrieving NFC rulesAndre Guedes1-3/+16
Access to NFC rules stored in adapter->nfc_rule_list is protect by adapter->nfc_rule_lock. The functions igc_ethtool_get_nfc_rule() and igc_ethtool_get_nfc_rules() are missing to hold the lock while accessing rule objects. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Fix 'sw_idx' type in struct igc_nfc_ruleAndre Guedes2-9/+9
The 'sw_idx' field from 'struct igc_nfc_rule' is u16 type but it is assigned an u32 value in igc_ethtool_init_nfc_rule(). This patch changes 'sw_idx' type to u32 so they match. Also, it makes more sense to call this field 'location' since it holds the NFC rule location. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-22igc: Refactor igc_ethtool_add_nfc_rule()Andre Guedes1-58/+92
Current implementation of igc_ethtool_add_nfc_rule() is quite long and a bit convoluted so this patch does a code refactoring to improve the code. Code related to NFC rule object initialization is refactored out to the local helper function igc_ethtool_init_nfc_rule(). Likewise, code related to NFC rule validation is refactored out to another local helper, igc_ethtool_is_nfc_rule_valid(). RX_CLS_FLOW_DISC check is removed since it is redundant. The macro is defined as the max value fsp->ring_cookie can have, so checking if fsp->ring_cookie >= adapter->num_rx_queues is already sufficient. Finally, some log messages are improved or added, and obvious comments are removed. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-21igc: Change byte order in struct igc_nfc_filterAndre Guedes2-22/+13
Every time we access the 'etype' and 'vlan_tci' fields from struct igc_nfc_filter to enable or disable filters in hardware we have to convert them from big endian to host order so it makes more sense to simply have these fields in host order. The byte order conversion should take place in igc_ethtool_get_nfc_ rule() and igc_ethtool_add_nfc_rule(), which are called by .get_rxnfc and .set_rxnfc ethtool ops, since ethtool subsystem is the one who deals with them in big endian order. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-04-30 00:47:08 +0000