| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The current logic to put interface into VLAN Promiscous mode is not correct.
We should increment "adapter->vlans_added" before calling be_vid_config().
Also removed some unwanted log messages.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver does not check value returned by dma_map_page. The patch
fixes this.
v2: Removed the bugfix for non-bug ;-) (thanks Sathya)
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <Sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch cleans-up wake-on-lan code in the following ways:
1) Removes some driver hacks in be_cmd_get_acpi_wol_cap() that were based
on incorrect assumptions.
2) Uses the adapter->wol_en and wol_cap variables for checking if WoL
is supported and enabled on an interface instead of referring to the
exclusion list via the macro be_is_wol_supported()
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The use of NTKW_MAC_QUERY cmd has been deprecated for Skyhawk-R.
Replace the last remaining usage in be_vfs_mac_query() routine.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead, use the tail of the RXQ to pick the associated RXQ entry
This fix is required in preparation for supporting RXQ lengths greater than 1K.
For such queues, the frag index in the RX-compl entry is not valid as it is only a 10 bit entry not capable of addressing RXQs longer than 1K.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As be2net is used even by the 40Gbps Skyhawk-R chip
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An earlier commit (f25b119c "Fix error messages while driver load for VFs")
incorrectly set the adapter->cmd_privileges value for VFs (in a
multi-channel config) to MAX_PRIVILEGES. This causes FW cmd failures
and avoidable error logs when certian cmds are issued by a VF.
Also, move the multi-channel hack to be_cmds.c inside
be_cmd_get_fn_privileges() routine.
Fixes: f25b119c "Fix error messages while driver load for VFs"
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An ndo_set_mac_addr() call may be issued for a mac-addr that is already
active on an interface. If so, silently ignore the request. Sending such
a request to the FW, causes a "mac collision" error. The error is harmless
but is avoidable noise in the kernel log.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skyhawk-R FW does not support SET/GET_EXT_FAT_CAPABILITIES cmds via which
FW logging level can be controlled. Also, the hack used in BE3 to control
FW logging level via the ethtool interface is not needed in Skyhawk-R.
This patch also cleans up this code by moving be_set/get_fw_log_level()
routines to be_cmds.c where they belong.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
remove new line
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the GET_HSW_CONFIG cmd, the "pport" field must be set only while
querying the switch mode. When the "pport" field is set, the
"interface_id" field must be set to the port number, otherwise, it
must be set to adapter->if_handle.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently this cmd is used only for Lancer.
MCC_CREATE_EXT_V1 supports larger CQ-ids and additional event codes for the
async_event_bitmap field.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver wrongly assumes 16 EQs/vectors are available for each BE3 PF.
When SR-IOV is enabled, a BE3 PF can support only a max of 8 EQs.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The loopback test FW cmd may need upto 15 seconds to complete on
certain PHYs. This patch also fixes the name of the completion variable
used to synchronize FW cmd completions as it not used by the flashing
cmd alone anymore.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When *only* the default RXQ is used, the RSS policy must be disabled so
that all IP and no-IP traffic is placed into the default RXQ. If not,
IP traffic is dropped.
Also, issue the RSS_CONFIG cmd only if FW advertises RSS capability for
the interface.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During suspend-resume and lancer error recovery we will cleanup and
re-initialize the resources through be_clear() and be_setup() respectively.
During re-initialisation in be_setup(), if be_get_config() fails, we'll again
call be_clear() which will cause a NULL pointer dereference as adapter->pmac_id is
already freed.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Firmware update would be detected by looking at the sliport_error1/
sliport_error2 register values(0x02/0x00). If its not a FW reset the current
messaging would take place. If the error is due to FW reset, log a message to
user that "Firmware update in progress" and also do not log sliport_status and
sliport_error register values.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent be2net commit 6384a4d (adds a support for busy polling)
introduces a regression that results in kernel crash. It incorrectly
modified be_close() so napi_disable() is called only for the first queue.
This breaks a correct pairing of napi_enable/_disable for the rest
of event queues and causes a crash in subsequent be_open() call.
v2: Applied suggestions from Sathya
Fixes: 6384a4d ("be2net: add support for ndo_busy_poll")
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 55485e7b417b640870b14eceec4cfbcb2b3e7a92.
I applied the wrong version of this patch, the right one is coming up
next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent be2net commit 6384a4d (adds a support for busy polling)
introduces a regression that results in kernel crash. It incorrectly
modified be_close() so napi_disable() is called only for the first queue.
This breaks a correct pairing of napi_enable/_disable for the rest
of event queues and causes a crash in subsequent be_open() call.
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On BE3-R, the PF programs the initial MAC address for its VFs. Doing it again
in VF probe, causes a FW error which although harmless generates
an unnecessary error log message.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not being set currently. (This field is not applicable for Lancer)
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interrupts need to be enabled in be_resume, when adapter boots back up from D3cold.
disabling interrupts in be_suspend() just to be symmetric to be_resume().
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
|
|
Secondary unicast MAC addresses will get deleted only when the interface is UP.
When the interface is DOWN, though these secondary MAC addresses are unusable
and awaiting to be deleted, cause the firmware to believe that they are being used.
If the user intends to set a MAC address as primary MAC from one of these
secondary MAC addresses, the firmware returns a MAC address Collision error.
Delete these secondary MAC addresses during be_close.
The secondary MAC addresses list will be refreshed during interface open anyway.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently requests the firmware to enable rx_interface options
without considering if the interface was created with that capability.
This could cause commands to firmware to fail.
To avoid this, enable only those options on an interface if the interface
was created with that capability.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
|
|
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
|
|
In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.
The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.
This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.
Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.
Feedback would be appreciated!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function needn't to be public, so to make it as static.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interface type, which is being traced by "struct be_adapter::
if_type", isn't used currently. So we can remove that safely
according to Sathya's comments.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Includes:
- ndo_busy_poll implementation
- Locking between napi and busy_poll
- Fix rx_post_starvation (replenish rx-queues in out-of-mememory scenario)
logic to accomodate busy_poll.
v2 changes:
[Eric D.'s comment] call alloc_pages() with GFP_ATOMIC even in ndo_busy_poll
context as it is not allowed to sleep.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
old FW versions with latest driver
On very old FW versions < 4.0, the mailbox command to set interrupts
on the card succeeds even though it is not supported and should have
failed, leading to a scenario where interrupts do not work.
Hence warn users to upgrade to a suitable FW version to avoid seeing
broken functionality.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we log a message whenever pcie_enable_error_reporting fails.
The message clutters up logs, especially when we don't support it for VFs.
Instead enable this only for PFs and log a message when the call succeeds.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is a required field for all TX_CREATE cmd versions > 0.
This fixes a driver initialization failure, caused by recent SH-R Firmwares
(versions > 10.0.639.0) failing the TX_CREATE cmd when if_id field is
not passed.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SkyHawk-R can support RoCE. Add code to display RoCE specific
counters maintained in hardware.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moving to version 2 of GET_STATS command as SkyHawk-R supports
higher number of rings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the xmit path, the driver may drop some pkts due to reasons such as
DMA mapping errors, out of memory conditions or to protect HW from
unrecoverable errors. Add a counter in TX-stats for such drops.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current EQ delay calculation for AIC is based only on RX packet rate.
This fails to be effective when there's only TX and no RX.
This patch inclues:
- Calculating EQ-delay based on both RX and TX pps.
- Modifying EQ-delay of all EQs via one cmd, instead of issuing a separate
cmd for each EQ.
- A new structure to store interrupt coalescing parameters, in a separate
cache-line from the EQ-obj.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This cmd needs to be sent to FW when enabling VFs (currently used only
for Lancer.) Also, avoid calling the cmd when driver loads and finds that
VFs are already enabled from a previous load.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On BE3-R 1G ports (identified by port numbers 2 and 3) the FW cannot properly
support multiple TXQs. This also makes the number of RX and TX queues symmetric
as only a single RXQ is available on 1G ports.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
