Age | Commit message (Collapse) | Author | Files | Lines |
|
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
[1] https://standards.ieee.org/standard/802_3-2005.html
Fixes: c3168cabe1af ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TC-MATCHALL classifier offload with TC-POLICE action applied for
all outgoing traffic on the underlying interface. Split flow block
offload to support both egress and ingress classification.
For example, to rate limit all outgoing traffic to 1 Gbps:
$ tc qdisc add dev enp2s0f4 clsact
$ tc filter add dev enp2s0f4 egress matchall skip_sw \
action police rate 1Gbit burst 8Kbit
Note that skip_sw is important. Otherwise, both stack and hardware
will end up doing policing. Policing can't be shared across flow
blocks. Only 1 egress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Removed check to reject police offload if prio is not 1.
- Moved TC_SETUP_BLOCK code to separate function.
v3:
- Added check to reject police offload if prio is not 1.
- Assign block_shared variable only for TC_SETUP_BLOCK.
v2:
- Added check to reject flow block sharing for policers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix several spelling typos in comments in t4_hw.c.
Signed-off-by: Arkadiusz Drabczyk <arkadiusz@drabczyk.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8c0d3a02c130 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:6216:14:
warning: symbol 't4_get_tp_e2c_map' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 2391b0030e241386d710df10e53e2cfc3c5d4fc1 which has
introduced regression. Now SGE's BAR2 Doorbell/GTS Page Size is
interpreted correctly in the firmware itself by using actual host
page size. Hence previous commit needs to be reverted.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for validating hardware filter spec configured in firmware
before offloading exact match flows.
Use the new fw api FW_PARAM_DEV_FILTER_MODE_MASK to read the filter mode
and mask from firmware. If the api isn't supported, then fall-back to
older way of reading just the mode from indirect register.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hash (exact-match) filters used for offloading flows share the
same active region resources on the chip with upper layer drivers,
like iw_cxgb4, chcr, etc. Currently, only either Hash filters
or ULDs can use the active region resources, but not both. Hence,
use the new firmware configuration parameters (when available)
to allow both the Hash filters and ULDs to share the
active region simultaneously.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch advertises Forward Error Correction in ethtool
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of these macros were conflicting with global namespace,
hence prefixing them with CXGB4.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are rare cases where a PL_INT_CAUSE bit may end up getting
set when the corresponding PL_INT_ENABLE bit isn't set.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
T6 introduced a Timer Mechanism in SGE called the
SGE Doorbell Queue Timer. With this we can now configure
TX Queues to get CIDX Updates when:
Time(CIDX == PIDX) >= Timer
Previously we rely on TX Queue Status Page updates by hardware
for DMA completions. This will make Hardware/Firmware actually
deliver the CIDX Updates as Ingress Queue messages with
commensurate Interrupts.
So we now have a new RX Path component for processing CIDX Updates
and reclaiming TX Descriptors faster.
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) Speed should be supported by Physical Port Capabilities.
2) report Forward Error Correction mode which are available.
3) Added few comments.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5883:6:
warning: variable 'multitrc' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:8585:32:
warning: variable 'speed' set but not used [-Wunused-but-set-variable]
'multitrc' never used since introduction in
commit 8e3d04fd7d70 ("cxgb4: Add MPS tracing support")
'speed' never used since introduction in
commit c3168cabe1af ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the fw supports returning VIN/VIVLD in FW_VI_CMD save it
in port_info structure else retrieve these from viid and save
them in port_info structure. Do the same for smt_idx from
FW_VI_MAC_CMD
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SGE Host Page Size has nothing to do with the actual
Host Page Size. It's the SGE's BAR2 Doorbell/GTS Page Size
for interpreting the SGE Ingress/Egress Queue per Page values.
Firmware reads all of these things and makes all the
subsequent changes necessary. The Host Driver uses the SGE
Host Page Size in order to properly calculate BAR2 Offsets.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when 32 bit port capability is in use, use FW_PORT_ACTION_L1_CFG32
rather than FW_PORT_ACTION_L1_CFG.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not put host-endian 0 or 1 into big endian feild.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent commit updated vlan_cmd.dropnovlan_fm but failed to remove
the older assignment. Fix this by removing the former redundant
assignment.
Detected by CoverityScan, CID#1473290 ("Unused value")
Fixes: a89cdd8e7c74 ("cxgb4: impose mandatory VLAN usage when non-zero TAG ID")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a non-zero VLAN Tag ID is passed to t4_set_vlan_acl()
then impose mandatory VLAN Usage with that VLAN ID.
I.e any other VLAN ID should result in packets getting
dropped.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114777 ("Missing break in switch")
Addresses-Coverity-ID: 114778 ("Missing break in switch")
Addresses-Coverity-ID: 114779 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All conflicts were trivial overlapping changes, so reasonably
easy to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
t4_get_flash_params() fails in a fatal fashion if the FLASH part isn't
one of the recognized parts. But this leads to desperate efforts to update
drivers when various FLASH parts which we are using suddenly become
unavailable and we need to substitute new FLASH parts. This has lead to
more than one Customer Field Emergency when a Customer has an old driver
and suddenly can't use newly shipped adapters.
This commit fixes this by simply assuming that the FLASH part is 4MB in
size if it can't be identified. Note that all Chelsio adapters will have
flash parts which are at least 4MB in size.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In highly constrained resources environments (like the 124VF
T5 and 248VF T6 configurations), PF4 may not have very many
resources at all and we need to adapt to whatever we've been
allocated, this patch adds support to get the provisioned
resources.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add FORCE_PAUSE bit to force local pause settings instead
of using auto negotiated values.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have a confusion of two different abstractions in the Common
Code: Physical Link (Port) and Logical Network Interface (Virtual
Interface), and we haven't been properly managing the state of the
intersection of those two abstractions.
On the one hand we have the Physical state of the Link -- up or down --
and on the other we have the logical state of the VI, enabled or not.
{ethN} refers to both the Physical and Logical State. In this case,
ifconfig only affects/interrogates the Logical State of a VI,
and ethtool only deals with the Physical State. And these are different.
So, just because we disable the VI, we don't really want to change the
Physical Link Up/Down state. Thus, the previous hack to set
"lc->link_ok = 0" when we disable a VI is completely incorrect.
Where we get into trouble is where the Physical Link State and the
Logical VI State cross swords. And that happens in
t4_handle_get_port_info() where we need to manage/safe the Physical
Link State, but we also need to know when the Logical VI State has
changed and pass that back up to the OS-dependent Driver routine
t4_os_link_changed() which is concerned about the Logical Interface.
So we enable a VI and that causes Firmware to send us a new Port
Information message, but if none of the Physical Link State
particulars have changed, we don't call t4_os_link_changed().
This fix uses the existing OS Contract APIs for the Common Code to
inform the OS-dependent portion of the Host Driver when the "Link" (really
Logical Network Interface) is "up" or "down". A new API
t4_enable_pi_params() is added which calls t4_enable_vi_params() and,
if that is successful, then calls back to the OS Contract API
t4_os_link_changed() notifying the OS-dependent layer of the
potential Link State change.
Original Work by : Casey Leedom <leedom@chelsio.com>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
newer SFPs like SFP28 and QSFP28 Transceiver Modules present
several new possibilities which we haven't faced before. Fix the
assumptions in the code reflecting the more limited capabilities
of previous Transceiver Module systems
Original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
trigger an L1 configure operation when a transceiver module
is inserted in order to cause current "sticky" options like
Requested Forward Error Correction to be reapplied.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MDI Port Capabilities bit definitions were inconsistent with
regard to the MDI enum values. 2 bits used to define MDI in
the port capabilities are not really separable, it's a 2-bit
field with 4 different values. Change the port capability bit
definitions to be "AUTO" and "STRAIGHT" in order to get them
to line up with the enum's.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for matching flows based on tunnel VNI value.
Introduces fw APIs for allocating/removing MPS entries related
to encapsulation. And uses the same while adding/deleting filters
for offloading flows based on tunnel VNI match.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for new 32MB and 64MB ISSI (Integrated Silicon
Solution, Inc.) FLASH parts.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depend on the firmware sending us link status changes,
rather than assuming that the link goes down upon L1
configuration.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HMA(Host Memory Access) maps a part of host memory for T6-SO memfree cards.
This commit does the following:
- Query FW to check if we have HMA support. If yes, the params will
return HMA size configured in FW. We will dma map memory based
on this size.
- Also contains changes to get HMA memory information via debugfs.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Michael Werner <werner@chelsio.com>
Signed-off-by: Ganesh GR <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TP Congestion Map entry for single-port T6 cards.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
We've run into a problem where our device is attached
to a Virtual Machine and the use of the new pci_set_vpd_size()
API doesn't help. The VM kernel has been informed that
the accesses are okay, but all of the actual VPD Capability
Accesses are trapped down into the KVM Hypervisor where it
goes ahead and imposes the silent denials.
The right idea is to follow the kernel.org
commit 1c7de2b4ff88 ("PCI: Enable access to non-standard VPD for
Chelsio devices (cxgb3)") which Alexey Kardashevskiy authored
to establish a PCI Quirk for our T3-based adapters. This commit
extends that PCI Quirk to cover Chelsio T4 devices and later.
The advantage of this approach is that the VPD Size gets set early
in the Base OS/Hypervisor Boot and doesn't require that the cxgb4
driver even be available in the Base OS/Hypervisor. Thus PF4 can
be exported to a Virtual Machine and everything should work.
Fixes: 67e658794ca1 ("cxgb4: Set VPD size so we can read both VPD structures")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rework logic to read EDC and MC. Do 32-bit reads at a time.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only contact firmware if it's alive _AND_ if use_bd (use backdoor
access) is not set when issuing FW_LDST_CMD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If firmware reports error, reset FW_OK flag.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
t4_wr_mbox_meat_timeout() can be called from both softirq
context and process context, hence protect the mbox with
spin_lock_bh() instead of simple spin_lock()
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
implement ndo_set_vf_vlan for mgmt netdevice to configure
the PCIe VF.
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ndo_udp_tunnel_add and ndo_udp_tunnel_del
to support vxlan tunnelling.
Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
commit 96ac18f14a5a ("cxgb4: Add support for new flash parts")
removed initialization of adapter->params.sf_fw_start causing issues
while flashing firmware to card. We no longer need sf_fw_start
in adapter->params as we already have macros defined for FW flash
addresses.
Fixes: 96ac18f14a5a ("cxgb4: Add support for new flash parts")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for new Backplane XLAUI port type.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RSS table is 4k for T6 and later cards, add check for the
same.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify PCIe Completion Timeout setting by using the
pcie_capability_clear_and_set_word() interface. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for ethtool get_module_info() and get_module_eeprom()
callbacks that will dump necessary information for a SFP.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|