| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In my test setup, I had a SAMA5D27 device configured with ip forwarding, and
second device with usb ethernet (r8152) sending ICMP packets. If the packet
was larger than about 220 bytes, the SAMA5 device would "oops" with the
following trace:
kernel BUG at net/core/skbuff.c:1863!
Internal error: Oops - BUG: 0 [#1] ARM
Modules linked in: xt_MASQUERADE ppp_async ppp_generic slhc iptable_nat xt_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 can_raw can bridge stp llc ipt_REJECT nf_reject_ipv4 sd_mod cdc_ether usbnet usb_storage r8152 scsi_mod mii o
ption usb_wwan usbserial micrel macb at91_sama5d2_adc phylink gpio_sama5d2_piobu m_can_platform m_can industrialio_triggered_buffer kfifo_buf of_mdio can_dev fixed_phy sdhci_of_at91 sdhci_pltfm libphy sdhci mmc_core ohci_at91 ehci_atmel o
hci_hcd iio_rescale industrialio sch_fq_codel spidev prox2_hal(O)
CPU: 0 PID: 0 Comm: swapper Tainted: G O 5.9.1-prox2+ #1
Hardware name: Atmel SAMA5
PC is at skb_put+0x3c/0x50
LR is at macb_start_xmit+0x134/0xad0 [macb]
pc : [<c05258cc>] lr : [<bf0ea5b8>] psr: 20070113
sp : c0d01a60 ip : c07232c0 fp : c4250000
r10: c0d03cc8 r9 : 00000000 r8 : c0d038c0
r7 : 00000000 r6 : 00000008 r5 : c59b66c0 r4 : 0000002a
r3 : 8f659eff r2 : c59e9eea r1 : 00000001 r0 : c59b66c0
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c53c7d Table: 2640c059 DAC: 00000051
Process swapper (pid: 0, stack limit = 0x75002d81)
<snipped stack>
[<c05258cc>] (skb_put) from [<bf0ea5b8>] (macb_start_xmit+0x134/0xad0 [macb])
[<bf0ea5b8>] (macb_start_xmit [macb]) from [<c053e504>] (dev_hard_start_xmit+0x90/0x11c)
[<c053e504>] (dev_hard_start_xmit) from [<c0571180>] (sch_direct_xmit+0x124/0x260)
[<c0571180>] (sch_direct_xmit) from [<c053eae4>] (__dev_queue_xmit+0x4b0/0x6d0)
[<c053eae4>] (__dev_queue_xmit) from [<c05a5650>] (ip_finish_output2+0x350/0x580)
[<c05a5650>] (ip_finish_output2) from [<c05a7e24>] (ip_output+0xb4/0x13c)
[<c05a7e24>] (ip_output) from [<c05a39d0>] (ip_forward+0x474/0x500)
[<c05a39d0>] (ip_forward) from [<c05a13d8>] (ip_sublist_rcv_finish+0x3c/0x50)
[<c05a13d8>] (ip_sublist_rcv_finish) from [<c05a19b8>] (ip_sublist_rcv+0x11c/0x188)
[<c05a19b8>] (ip_sublist_rcv) from [<c05a2494>] (ip_list_rcv+0xf8/0x124)
[<c05a2494>] (ip_list_rcv) from [<c05403c4>] (__netif_receive_skb_list_core+0x1a0/0x20c)
[<c05403c4>] (__netif_receive_skb_list_core) from [<c05405c4>] (netif_receive_skb_list_internal+0x194/0x230)
[<c05405c4>] (netif_receive_skb_list_internal) from [<c0540684>] (gro_normal_list.part.0+0x14/0x28)
[<c0540684>] (gro_normal_list.part.0) from [<c0541280>] (napi_complete_done+0x16c/0x210)
[<c0541280>] (napi_complete_done) from [<bf14c1c0>] (r8152_poll+0x684/0x708 [r8152])
[<bf14c1c0>] (r8152_poll [r8152]) from [<c0541424>] (net_rx_action+0x100/0x328)
[<c0541424>] (net_rx_action) from [<c01012ec>] (__do_softirq+0xec/0x274)
[<c01012ec>] (__do_softirq) from [<c012d6d4>] (irq_exit+0xcc/0xd0)
[<c012d6d4>] (irq_exit) from [<c0160960>] (__handle_domain_irq+0x58/0xa4)
[<c0160960>] (__handle_domain_irq) from [<c0100b0c>] (__irq_svc+0x6c/0x90)
Exception stack(0xc0d01ef0 to 0xc0d01f38)
1ee0: 00000000 0000003d 0c31f383 c0d0fa00
1f00: c0d2eb80 00000000 c0d2e630 4dad8c49 4da967b0 0000003d 0000003d 00000000
1f20: fffffff5 c0d01f40 c04e0f88 c04e0f8c 30070013 ffffffff
[<c0100b0c>] (__irq_svc) from [<c04e0f8c>] (cpuidle_enter_state+0x7c/0x378)
[<c04e0f8c>] (cpuidle_enter_state) from [<c04e12c4>] (cpuidle_enter+0x28/0x38)
[<c04e12c4>] (cpuidle_enter) from [<c014f710>] (do_idle+0x194/0x214)
[<c014f710>] (do_idle) from [<c014fa50>] (cpu_startup_entry+0xc/0x14)
[<c014fa50>] (cpu_startup_entry) from [<c0a00dc8>] (start_kernel+0x46c/0x4a0)
Code: e580c054 8a000002 e1a00002 e8bd8070 (e7f001f2)
---[ end trace 146c8a334115490c ]---
The solution was to force nonlinear buffers to be cloned. This was previously
reported by Klaus Doth (https://www.spinics.net/lists/netdev/msg556937.html)
but never formally submitted as a patch.
This is the third revision, hopefully the formatting is correct this time!
Suggested-by: Klaus Doth <krnl@doth.eu>
Fixes: 653e92a9175e ("net: macb: add support for padding and fcs computation")
Signed-off-by: Mark Deneen <mdeneen@saucontech.com>
Link: https://lore.kernel.org/r/20201030155814.622831-1-mdeneen@saucontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds support for 10GBASE-R interface to the linux driver for
Cadence's ethernet controller.
This controller has separate MAC's and PCS'es for low and high speed paths.
High speed PCS supports 100M, 1G, 2.5G, 5G and 10G through rate adaptation
implementation. However, since it doesn't support auto negotiation, linux
driver is modified to support 10GBASE-R instead of USXGMII.
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Link: https://lore.kernel.org/r/1603975627-18338-1-git-send-email-pthombar@cadence.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The at91rm9200 variant used by a few chips including the MSC313 supports
two Tx descriptors (one frame being serialized and another one queued).
However the driver only implemented a single one, which adds a dead time
after each transfer to receive and process the interrupt and wake the
queue up, preventing from reaching line rate.
This patch implements a very basic 2-deep queue to address this limitation.
The tests run on a Breadbee board equipped with an MSC313E show that at
1 GHz, HTTP traffic on medium-sized objects (45kB) was limited to exactly
50 Mbps before this patch, and jumped to 76 Mbps with this patch. And tests
on a single TCP stream with an MTU of 576 jump from 10kpps to 15kpps. With
1500 byte packets it's now possible to reach line rate versus 75 Mbps
before.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-4-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RM9200 supports one frame being sent while another one is waiting in
queue. This avoids the dead time that follows the emission of a frame
and which prevents one from reaching line speed.
Right now the driver supports only a single skb, so we'll first replace
the rm9200-specific skb info with an array of two macb_tx_skb (already
used by other drivers). This patch only moves the skb_length to
txq[0].size and skb_physaddr to skb[0].mapping but doesn't perform any
other change. It already uses [desc] in order to minimize future changes.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-3-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Transmit Buffer Register Empty replaces TXERR on RM9200 and signals the
sender may try to send again becase the last queued frame is no longer
in queue (being transmitted or already transmitted).
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-2-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
struct macb_platform_data is only used by macb_pci to register the platform
device, move its definition to cadence/macb.h and remove platform_data/macb.h
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A couple of drivers had a "generic documentation" section that
would trigger a "can't understand" message from W=1 compiles.
Fix by using correct DOC: tags in the generic sections.
Fixed Warnings:
drivers/net/ethernet/arc/emac_arc.c:4: info: Scanning doc for c
drivers/net/ethernet/cadence/macb_pci.c:3: warning: missing initial short description on line:
* Cadence GEM PCI wrapper.
drivers/net/ethernet/cadence/macb_pci.c:3: info: Scanning doc for Cadence
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PAE bit of NCFGR register, when set, pauses transmission
if a non-zero 802.3 classic pause frame is received.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
I just recently noticed that ethernet does not work anymore since v5.5
on the GARDENA smart Gateway, which is based on the AT91SAM9G25.
Debugging showed that the "GEM bits" in the NCFGR register are now
unconditionally accessed, which is incorrect for the !macb_is_gem()
case.
This patch adds the macb_is_gem() checks back to the code
(in macb_mac_config() & macb_mac_link_up()), so that the GEM register
bits are not accessed in this case any more.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reto Schneider <reto.schneider@husqvarnagroup.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3113e8b203b9debfb72d81e0f3dcace
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle the Wake-on-Lan interrupt for the Cadence MACB Ethernet
controller.
As we do for the GEM version, we handle of WoL interrupt in a
specialized interrupt handler for MACB version that is positionned
just between suspend() and resume() calls.
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adapt the Wake-on-Lan feature to the Cadence GEM Ethernet controller.
This controller has different register layout and cannot be handled by
previous code.
We disable completely interrupts on all the queues but the queue 0.
Handling of WoL interrupt is done in another interrupt handler
positioned depending on the controller version used, just between
suspend() and resume() calls.
It allows to lower pressure on the generic interrupt hot path by
removing the need to handle 2 tests for each IRQ: the first figuring out
the controller revision, the second for actually knowing if the WoL bit
is set.
Queue management in suspend()/resume() functions inspired from RFC patch
by Harini Katakam <harinik@xilinx.com>, thanks!
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is one RGMII check not using the phy_interface_mode_is_rgmii()
helper. This prevents the driver from configuring the MAC properly when
using a phy-mode that is not just rgmii, e.g. rgmii-rxid. This became an
issue on sama5d3 xplained since the ksz9031 driver is hadling phy-mode
properly and the phy-mode has to be set to rgmii-rxid.
Fixes: bcf3440c6dd78bfe ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All conflicts seemed rather trivial, with some guidance from
Saeed Mameed on the tc_ct.c one.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The calls to pm_runtime_force_suspend/resume() functions are only
relevant if the device is not configured to act as a WoL wakeup source.
Add the device_may_wakeup() test before calling them.
Fixes: 3e2a5e153906 ("net: macb: add wake-on-lan support via magic packet")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we now use the phylink call to phylink_stop() in the non-WoL path,
there is no need for this call to netif_carrier_off() anymore. It can
disturb the underlying phylink FSM.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keep previous function goals and integrate phylink actions to them.
phylink_ethtool_get_wol() is not enough to figure out if Ethernet driver
supports Wake-on-Lan.
Initialization of "supported" and "wolopts" members is done in phylink
function, no need to keep them in calling function.
phylink_ethtool_set_wol() return value is considered and determines
if the MAC has to handle WoL or not. The case where the PHY doesn't
implement WoL leads to the MAC configuring it to provide this feature.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the way the "magic-packet" DT property is handled in the
macb_probe() function, matching DT binding documentation.
Now we mark the device as "wakeup capable" instead of calling the
device_init_wakeup() function that would enable the wakeup source.
For Ethernet WoL, enabling the wakeup_source is done by
using ethtool and associated macb_set_wol() function that
already calls device_set_wakeup_enable() for this purpose.
That would reduce power consumption by cutting more clocks if
"magic-packet" property is set but WoL is not configured by ethtool.
Fixes: 3e2a5e153906 ("net: macb: add wake-on-lan support via magic packet")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the proper struct device pointer to check if the wakeup flag
and wakeup source are positioned.
Use the one passed by function call which is equivalent to
&bp->dev->dev.parent.
It's preventing the trigger of a spurious interrupt in case the
Wake-on-Lan feature is used.
Fixes: d54f89af6cc4 ("net: macb: Add pm runtime support")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove is_udp variable that is used in only one place and use
ip_hdr(skb)->protocol == IPPROTO_UDP check instead.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not initialize queue variable. It is already initialized in for loops.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use hweight32() to count set bits in queue_mask.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bit 0 of queue_mask is set at the beginning of
macb_probe_queues() function. Do not set it again after reading
DGFG6 but instead use "|=" operator.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DMA buffers were not freed on failure path of at91ether_open().
Along with changes for freeing the DMA buffers the enable/disable
interrupt instructions were moved to at91ether_start()/at91ether_stop()
functions and the operations on at91ether_stop() were done in
their reverse order (compared with how is done in at91ether_start()):
before this patch the operation order on interface open path
was as follows:
1/ alloc DMA buffers
2/ enable tx, rx
3/ enable interrupts
and the order on interface close path was as follows:
1/ disable tx, rx
2/ disable interrupts
3/ free dma buffers.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call pm_runtime_put_sync() on failure path of at91ether_open.
Fixes: e6a41c23df0d ("net: macb: ensure interface is not suspended on at91rm9200")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Undo previously done operation in case macb_phylink_connect()
fails. Since macb_reset_hw() is the 1st undo operation the
napi_exit label was renamed to reset_hw.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent change added a disable to NAPI into macb_open, this was
intended to only happen on the error path but accidentally applies
to all paths. This causes NAPI to be disabled on the success path, which
leads to the network to no longer functioning.
Fixes: 014406babc1f ("net: cadence: macb: disable NAPI on error")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
When the PHY is not working, the macb driver crash on a second try to
setup it.
[ 78.545994] macb e000b000.ethernet eth0: Could not attach PHY (-19)
ifconfig: SIOCSIFFLAGS: No such device
[ 78.655457] ------------[ cut here ]------------
[ 78.656014] kernel BUG at /linux-next/include/linux/netdevice.h:521!
[ 78.656504] Internal error: Oops - BUG: 0 [#1] SMP ARM
[ 78.657079] Modules linked in:
[ 78.657795] CPU: 0 PID: 122 Comm: ifconfig Not tainted 5.7.0-next-20200609 #1
[ 78.658202] Hardware name: Xilinx Zynq Platform
[ 78.659632] PC is at macb_open+0x220/0x294
[ 78.660160] LR is at 0x0
[ 78.660373] pc : [<c0b0a634>] lr : [<00000000>] psr: 60000013
[ 78.660716] sp : c89ffd70 ip : c8a28800 fp : c199bac0
[ 78.661040] r10: 00000000 r9 : c8838540 r8 : c8838568
[ 78.661362] r7 : 00000001 r6 : c8838000 r5 : c883c000 r4 : 00000000
[ 78.661724] r3 : 00000010 r2 : 00000000 r1 : 00000000 r0 : 00000000
[ 78.662187] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 78.662635] Control: 10c5387d Table: 08b64059 DAC: 00000051
[ 78.663035] Process ifconfig (pid: 122, stack limit = 0x(ptrval))
[ 78.663476] Stack: (0xc89ffd70 to 0xc8a00000)
[ 78.664121] fd60: 00000000 c89fe000 c8838000 c89fe000
[ 78.664866] fd80: 00000000 c11ff9ac c8838028 00000000 00000000 c0de6f2c 00000001 c1804eec
[ 78.665579] fda0: c19b8178 c8838000 00000000 ca760866 c8838000 00000001 00001043 c89fe000
[ 78.666355] fdc0: 00001002 c0de72f4 c89fe000 c0de8dc0 00008914 c89fe000 c199bac0 ca760866
[ 78.667111] fde0: c89ffddc c8838000 00001002 00000000 c8838138 c881010c 00008914 c0de7364
[ 78.667862] fe00: 00000000 c89ffe70 c89fe000 ffffffff c881010c c0e8bd48 00000003 00000000
[ 78.668601] fe20: c8838000 c8810100 39c1118f 00039c11 c89a0960 00001043 00000000 000a26d0
[ 78.669343] fe40: b6f43000 ca760866 c89a0960 00000051 befe6c50 00008914 c8b2a3c0 befe6c50
[ 78.670086] fe60: 00000003 ee610500 00000000 c0e8ef58 30687465 00000000 00000000 00000000
[ 78.670865] fe80: 00001043 00000000 000a26d0 b6f43000 c89a0600 ee40ae7c c8870d00 c0ddabf4
[ 78.671593] fea0: c89ffeec c0ddabf4 c89ffeec c199bac0 00008913 c0ddac48 c89ffeec c89fe000
[ 78.672324] fec0: befe6c50 ca760866 befe6c50 00008914 c89fe000 befe6c50 c8b2a3c0 c0dc00e4
[ 78.673088] fee0: c89a0480 00000201 00000cc0 30687465 00000000 00000000 00000000 00001002
[ 78.673822] ff00: 00000000 000a26d0 b6f43000 ca760866 00008914 c8b2a3c0 000a0ec4 c8b2a3c0
[ 78.674576] ff20: befe6c50 c04b21bc 000d5004 00000817 c89a0480 c0315f94 00000000 00000003
[ 78.675415] ff40: c19a2bc8 c8a3cc00 c89fe000 00000255 00000000 00000000 00000000 000d5000
[ 78.676182] ff60: 000f6000 c180b2a0 00000817 c0315e64 000d5004 c89fffb0 b6ec0c30 ca760866
[ 78.676928] ff80: 00000000 000b609b befe6c50 000a0ec4 00000036 c03002c4 c89fe000 00000036
[ 78.677673] ffa0: 00000000 c03000c0 000b609b befe6c50 00000003 00008914 befe6c50 000b609b
[ 78.678415] ffc0: 000b609b befe6c50 000a0ec4 00000036 befe6e0c befe6f1a 000d5150 00000000
[ 78.679154] ffe0: 000d41e4 befe6bf4 00019648 b6e4509c 20000010 00000003 00000000 00000000
[ 78.681059] [<c0b0a634>] (macb_open) from [<c0de6f2c>] (__dev_open+0xd0/0x154)
[ 78.681571] [<c0de6f2c>] (__dev_open) from [<c0de72f4>] (__dev_change_flags+0x16c/0x1c4)
[ 78.682015] [<c0de72f4>] (__dev_change_flags) from [<c0de7364>] (dev_change_flags+0x18/0x48)
[ 78.682493] [<c0de7364>] (dev_change_flags) from [<c0e8bd48>] (devinet_ioctl+0x5e4/0x75c)
[ 78.682945] [<c0e8bd48>] (devinet_ioctl) from [<c0e8ef58>] (inet_ioctl+0x1f0/0x3b4)
[ 78.683381] [<c0e8ef58>] (inet_ioctl) from [<c0dc00e4>] (sock_ioctl+0x39c/0x664)
[ 78.683818] [<c0dc00e4>] (sock_ioctl) from [<c04b21bc>] (ksys_ioctl+0x2d8/0x9c0)
[ 78.684343] [<c04b21bc>] (ksys_ioctl) from [<c03000c0>] (ret_fast_syscall+0x0/0x54)
[ 78.684789] Exception stack(0xc89fffa8 to 0xc89ffff0)
[ 78.685346] ffa0: 000b609b befe6c50 00000003 00008914 befe6c50 000b609b
[ 78.686106] ffc0: 000b609b befe6c50 000a0ec4 00000036 befe6e0c befe6f1a 000d5150 00000000
[ 78.686710] ffe0: 000d41e4 befe6bf4 00019648 b6e4509c
[ 78.687582] Code: 9a000003 e5983078 e3130001 1affffef (e7f001f2)
[ 78.688788] ---[ end trace e3f2f6ab69754eae ]---
This is due to NAPI left enabled if macb_phylink_connect() fail.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A call of the function macb_init() can fail in the function
fu540_c000_init. The related system resources were not released
then. use devm_platform_ioremap_resource() to replace ioremap()
to fix it.
Fixes: c218ad559020ff9 ("macb: Add support for SiFive FU540-C000")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Yash Shah <yash.shah@sifive.com>
Suggested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d1cbfd771ce8 ("ptp_clock: Allow for it to be optional") changed
all PTP-capable Ethernet drivers from `select PTP_1588_CLOCK` to `imply
PTP_1588_CLOCK`, "in order to break the hard dependency between the PTP
clock subsystem and ethernet drivers capable of being clock providers."
As a result it is possible to build PTP-capable Ethernet drivers without
the PTP subsystem by deselecting PTP_1588_CLOCK. Drivers are required to
handle the missing dependency gracefully.
Some PTP-capable Ethernet drivers (e.g., TI_CPSW) factor their PTP code
out into separate drivers (e.g., TI_CPTS_MOD). The above commit also
changed these PTP-specific drivers to `imply PTP_1588_CLOCK`, making it
possible to build them without the PTP subsystem. But as Grygorii
Strashko noted in [1]:
On Wed, Apr 22, 2020 at 02:16:11PM +0300, Grygorii Strashko wrote:
> Another question is that CPTS completely nonfunctional in this case and
> it was never expected that somebody will even try to use/run such
> configuration (except for random build purposes).
In my view, enabling a PTP-specific driver without the PTP subsystem is
a configuration error made possible by the above commit. Kconfig should
not allow users to create a configuration with missing dependencies that
results in "completely nonfunctional" drivers.
I audited all network drivers that call ptp_clock_register() but merely
`imply PTP_1588_CLOCK` and found five PTP-specific drivers that are
likely nonfunctional without PTP_1588_CLOCK:
NET_DSA_MV88E6XXX_PTP
NET_DSA_SJA1105_PTP
MACB_USE_HWSTAMP
CAVIUM_PTP
TI_CPTS_MOD
Note how these symbols all reference PTP or timestamping in their name;
this is a clue that they depend on PTP_1588_CLOCK.
Change them from `imply PTP_1588_CLOCK` [2] to `depends on PTP_1588_CLOCK`.
I'm not using `select PTP_1588_CLOCK` here because PTP_1588_CLOCK has
its own dependencies, which `select` would not transitively apply.
Additionally, remove the `select NET_PTP_CLASSIFY` from CPTS_TI_MOD;
PTP_1588_CLOCK already selects that.
[1]: https://lore.kernel.org/lkml/c04458ed-29ee-1797-3a11-7f3f560553e6@ti.com/
[2]: NET_DSA_SJA1105_PTP had never declared any type of dependency on
PTP_1588_CLOCK (`imply` or otherwise); adding a `depends on PTP_1588_CLOCK`
here seems appropriate.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d1cbfd771ce8 ("ptp_clock: Allow for it to be optional")
Signed-off-by: Clay McClure <clay@daemons.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit e6a41c23df0d, while trying to fix an issue,
("net: macb: ensure interface is not suspended on at91rm9200")
introduced a refcounting regression, because in error case refcounter
must be balanced. Fix it by calling pm_runtime_put_noidle() in error case.
While here, fix the same mistake in other couple of places.
Fixes: e6a41c23df0d ("net: macb: ensure interface is not suspended on at91rm9200")
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fixed-link nodes are treated as PHY nodes by of_mdiobus_child_is_phy().
We must check if the interface is a fixed-link before looking up for PHY
nodes.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the macb ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
at91ether_init was handling the phy mode and speed but since the switch to
phylink, the NCFGR register got overwritten by macb_mac_config(). The issue
is that the RM9200_RMII bit and the MACB_CLK_DIV32 field are cleared
but never restored as they conflict with the PAE, GBE and PCSSEL bits.
Add new capability to differentiate between EMAC and the other versions of
the IP and use it to set and avoid clearing the relevant bits.
Also, this fixes a NULL pointer dereference in macb_mac_link_up as the EMAC
doesn't use any rings/bufffers/queues.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because of autosuspend, at91ether_start is called with clocks disabled.
Ensure that pm_runtime doesn't suspend the interface as soon as it is
opened as there is no pm_runtime support is the other relevant parts of the
platform support for at91rm9200.
Fixes: d54f89af6cc4 ("net: macb: Add pm runtime support")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GEM_MAX_TX_LEN currently resolves to 0x3FF8 for any IP version supporting
TSO with full 14bits of length field in payload descriptor. But an IP
errata causes false amba_error (bit 6 of ISR) when length in payload
descriptors is specified above 16387. The error occurs because the DMA
falsely concludes that there is not enough space in SRAM for incoming
payload. These errors were observed continuously under stress of large
packets using iperf on a version where SRAM was 16K for each queue. This
errata will be documented shortly and affects all versions since TSO
functionality was added. Hence limit the max length to 0x3FC0 (rounded).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IP TSO implementation does NOT require the length to be a
multiple of 8. That is only a requirement for UFO as per IP
documentation. Hence, exit macb_features_check function in the
beginning if the protocol is not UDP. Only when it is UDP,
proceed further to the alignment checks. Update comments to
reflect the same. Also remove dead code checking for protocol
TCP when calculating header length.
Fixes: 1629dd4f763c ("cadence: Add LSO support.")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
This patch fix the issue with fixed link. With fixed-link
device opening fails due to macb_phylink_connect not
handling fixed-link mode, in which case no MAC-PHY connection
is needed and phylink_connect return success (0), however
in current driver attempt is made to search and connect to
PHY even for fixed-link.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Signed-off-by: Milind Parab <mparab@cadence.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch modify MDIO read/write functions to support
communication with C45 PHY.
Signed-off-by: Milind Parab <mparab@cadence.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
