| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 4 very similar PHYs:
0x600d84a1: BCM54210E (rev B0)
0x600d84a2: BCM54210E (rev B1)
0x600d84a5: B50212E (rev B0)
0x600d84a6: B50212E (rev B1)
that need setting master mode manually. It's because they run in slave
mode by default with Automatic Slave/Master configuration disabled which
can lead to unreliable connection with massive ping loss.
So far it was reported for a board with BCM47189 SoC and B50212E B1 PHY
connected to the bgmac supported ethernet device. Telling PHY driver to
setup PHY properly solves this issue.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allows the BCMA version of the bgmac driver to obtain MAC address
from the device tree. If no MAC address is specified there, then
the previous behavior (obtaining MAC address from SPROM) is
used.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM471X and BCM535X are of the same family (from what I can derive from
internal documents). Group them into the case statement together, which
results in more code reuse.
Also, use existing helper variables to make the code a little more
readable too.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 34a5102c3235 ("net: bgmac: allocate struct bgmac just once
& don't copy it") the mac_addr member of struct bgmac is no longer
necessary to pass the MAC address to bgmac_enet_probe(). Instead it can
directly be stored in netdev->dev_addr.
Also use eth_hw_addr_random() instead of eth_random_addr() in case a
random MAC is nedded. This will make sure netdev->addr_assign_type will
be properly set.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding struct bcma_mdio was a workaround for bcma code not having access
to the struct bgmac used in the core code. Now we don't duplicate this
struct we can just use it internally in bcma code.
This simplifies code & allows access to all bgmac driver details from
all places in bcma code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far were were allocating struct bgmac in 3 places: platform code,
bcma code and shared bgmac_enet_probe function. The reason for this was
bgmac_enet_probe:
1) Requiring early-filled struct bgmac
2) Calling alloc_etherdev on its own in order to use netdev_priv later
This solution got few drawbacks:
1) Was duplicating allocating code
2) Required copying early-filled struct
3) Resulted in platform/bcma code having access only to unused struct
Solve this situation by simply extracting some probe code into the new
bgmac_alloc function.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the bgmac driver to allow for phy's defined by the device tree
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All three conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM53573 is a new series of Broadcom's SoCs. It's based on ARM and can
be found in two packages (versions): BCM53573 and BCM47189. It shares
some code with the Northstar family, but also requires some new quirks.
First of all there can be up to 2 Ethernet cores on this SoC. If that is
the case, they are connected to two different switch ports allowing some
more complex/optimized setups. It seems the second unit doesn't come
fully configured and requires some IRQ quirk.
Other than that only the first core is connected to the PHY. For the
second one we have to register fixed PHY (similarly to the Northstar),
otherwise generic PHY driver would get some invalid info.
This has been successfully tested on Tenda AC9 (BCM47189B0).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was failing on successful registration returning meaningless errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes: 55954f3bfdac ("net: ethernet: bgmac: move BCMA MDIO Phy code into a separate file")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bcma portion of the driver has been split off into a bcma specific
driver. This has been mirrored for the platform driver. The last
references to the bcma core struct have been changed into a generic
function call. These function calls are wrappers to either the original
bcma code or new platform functions that access the same areas via MMIO.
This necessitated adding function pointers for both platform and bcma to
hide which backend is being used from the generic bgmac code.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
