| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of enabling/disabling clocks at several locations in the driver,
Use the runtime_pm framework. This consolidates the actions for runtime PM
In the appropriate callbacks and makes the driver more readable and mantainable.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message
creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is
initialized with zero in alloc_can_err_skb() anyway.
So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we
can remove the obsolete OR operation entirely.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187
the assignment of the error location in CAN error messages had some bit wise
overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines
a single value which points to a location inside the CAN frame on the wire.
This patch fixes the assignments for the error locations in error messages.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.
Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
in operating state
- A bus error condition occurs which activates EI interrupt, system is
still suspended which means EI interrupt will be not be handled nor
cleared.
If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.
By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
|
|
'spi/topic/omap-uwire', 'spi/topic/owner', 'spi/topic/pxa' and 'spi/topic/pxa2xx' into spi-next
|
|
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sizeof() is invoked on an incorrect variable, likely due to some
copy-paste error, and this might result in memory corruption. Fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: netdev@vger.kernel.org
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct at91_can_data was used to pass a callback to the driver, allowing it
to switch the transceiver on and off. As all at91 boards are now using DT,
this is not used anymore, remove that structure.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch change description of the module.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes a bug in arbitration error reporting
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
While new PEAK_PCIE_OEM_ID has been defined since 3.17, no corresponding
entry has been added in the peak_pci_tbl[] of the peak_pci CAN driver.
This patch enables now users of the PCAN-PCI Express OEM card to run the
peak_pci driver too.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch defers the writing of the interrupts bits of the CTRL register order
to enables all interrupts atomically at the the of the flexcan_chip_start()
function.
Suggested-by: Torsten Lang <torsten.lang@uweschneider.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch gives the member of flexcan_priv holding mailboxes a sensible name,
by renaming from "cantxfg" to "mb":
struct flexcan_priv::cantxfg -> struct flexcan_priv::mb
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
address space
This patch renames the pointer to the mmio address space from "base" to "regs"
and changes the type from "void __iomem *" to "struct flexcan_regs __iomem *".
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch renames the "features" member of struct flexcan_devtype_data to
"quirks". The corresponding defines are renamed too, to reflect what they
actually do.
FLEXCAN_HAS_V10_FEATURES -> FLEXCAN_QUIRK_DISABLE_RXFG
FLEXCAN_HAS_BROKEN_ERR_STATE -> FLEXCAN_QUIRK_BROKEN_ERR_STATE
FLEXCAN_HAS_MECR_FEATURES -> FLEXCAN_QUIRK_DISABLE_MECR
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch changes the order the individual bits of the mcr register in
flexcan_chip_start() are or'ed together to match the datasheet. The inline
documentation is adjusted accordingly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removes unused header files from the flexcan driver.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes up the coding style to make checkpatch happier. Some typos are
also fixed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Kernel module for Allwinner A10/A20 CAN controller.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
|
|
The CAN FD data bittiming constants are provided via netlink only when there
are valid CAN FD constants available in priv->data_bittiming_const.
Due to the indirection of pointer assignments in the peak_usb driver the
priv->data_bittiming_const never becomes NULL - not even for non-FD adapters.
The data_bittiming_const points to zero'ed data which leads to this result
when running 'ip -details link show can0':
35: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state STOPPED restart-ms 0
pcan_usb: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
: dtseg1 0..0 dtseg2 0..0 dsjw 1..0 dbrp 0..0 dbrp-inc 0 <== BROKEN!
clock 8000000
This patch changes the struct peak_usb_adapter::bittiming_const and struct
peak_usb_adapter::data_bittiming_const to pointers to fix the assignemnt
problems.
Cc: linux-stable <stable@vger.kernel.org> # >= 4.0
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This message isn't really helpful for the general reader of the kernel
logs, so should not be printed with info level. All other register
programming outputs in the flexcan driver already use the debug level.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This fixes typos in gs_usb.c where 'receive' is misspelled
as 'recieve'.
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The regulators power and transceiver are optional. If those are not
present, the pointer (or error pointer) is correctly handled by the
driver, hence we can use devm_regulator_get_optional safely, which
avoids regulators getting created.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If a valid power regulator or a dummy regulator is used (which
happens to be the case when no regulator is specified), restart_work
is queued no matter whether the device was running or not at suspend
time. Since work queues get initialized in the ndo_open callback,
resuming leads to a NULL pointer exception.
Reverse exactly the steps executed at suspend time:
- Enable the power regulator in any case
- Enable the transceiver regulator if the device was running, even in
case we have a power regulator
- Queue restart_work only in case the device was running
Fixes: bf66f3736a94 ("can: mcp251x: Move to threaded interrupts instead of workqueues.")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Anant Gole <anantgole@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Commit 514ac99c64b "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit 36c01245eb8 "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.
This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.
This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.
Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The previous change 3973c526ae9c (net: can: c_can: Disable pins when CAN
interface is down) causes a slight glitch on the pinctrl settings when used.
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
the device core will automatically set the default pins. This causes the pins
to be momentarily set to the default and then to the sleep state in
register_c_can_dev(). By adding an optional "enable" state, boards can set the
default pin state to be disabled and avoid the glitch when the switch from
default to sleep first occurs. If the "enable" state is not available
c_can_pinctrl_select_state() falls back to using the "default" pinctrl state.
[Roger Q] - Forward port to v4.2 and use pinctrl_get_select().
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
All the error messages in the driver but the ones from devm_clk_get() failures
use similar format. Make those two messages consitent with others.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Also print the error code when the request_irq() call fails in rcar_can_open(),
rewording the error message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix typo in the first error message printed by rcar_can_open().
Based on the original patch by Vladimir Barinov.
Fixes: 862e2b6af941 ("can: rcar_can: support all input clocks")
Reported-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Printing IRQ # using "%x" and "%u" unsigned formats isn't quite correct as
'ndev->irq' is of type *int*, so the "%d" format needs to be used instead.
While fixing this, beautify the dev_info() message in rcar_can_probe() a bit.
Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
rcar_can_probe() regards 0 as a wrong IRQ #, despite platform_get_irq() that it
calls returns negative error code in that case. This leads to the following
being printed to the console when attempting to open the device:
error requesting interrupt fffffffa
because rcar_can_open() calls request_irq() with a negative IRQ #, and that
function naturally fails with -EINVAL.
Check for the negative error codes instead and propagate them upstream instead
of just returning -ENODEV.
Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As reported by Manfred Schlaegl here
http://marc.info/?l=linux-netdev&m=143482089824232&w=2
commit 514ac99c64b "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
As net timestamping is influenced by several players (netstamp_needed and
netdev_tstamp_prequeue) Manfred missed a proper timestamp which leads to
CAN frame loss.
As skb timestamping became now mandatory for CAN related skbs this patch
makes sure that received CAN skbs always have a proper timestamp set.
Maybe there's a better solution in the future but this patch fixes the
CAN frame loss so far.
Reported-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
