| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In commit 88462d2a7830 ("can: flexcan: Remodel FlexCAN register r/w APIs
for big endian FlexCAN controllers.") the following logic was
implemented:
if the dt property "big-endian" is given or
the device is compatible to "fsl,p1010-flexcan":
use big-endian mode;
else
use little-endian mode;
This relies on commit d50f4630c2e1 ("arm: dts: Remove p1010-flexcan
compatible from imx series dts") which was applied a few commits later.
Without this commit (or an old device tree used for booting a new
kernel) the flexcan devices on i.MX25, i.MX28, i.MX35 and i.MX53 match
the 'the device is compatible to "fsl,p1010-flexcan"' test and so are
switched erroneously to big endian mode.
Instead of the check above put a quirk in devtype data and rely on
of_match_device yielding the most compatible match
Fixes: 88462d2a7830 ("can: flexcan: Remodel FlexCAN register r/w APIs for big endian FlexCAN controllers.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Gavin Schenk <g.schenk@eckelmann.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.16
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
|
|
The flexcan_start_xmit() function compares the frame length with data
register length to write frame content into data[0] and data[1]
register. Data register length is 4 bytes and frame maximum length is 8
bytes.
Fix the check that compares frame length with 3. Because the register
length is 4.
Signed-off-by: Luu An Phu <phu.luuan@nxp.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Small overlapping change conflict ('net' changed a line,
'net-next' added a line right afterwards) in flexcan.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for VF610 to report correct state
transitions.
Tested-by: Mirza Krak <mirza.krak@gmail.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The flexcan IP cores used on MX25 and MX35 do not generate Error Passive
IRQs. Update the IP core overview table in the driver accordingly.
Suggested-by: ZHU Yi (ST-FIR/ENG1-Zhu) <Yi.Zhu5@cn.bosch.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds platform specific details for NXP SOC LS1021A to the
flexcan driver code.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
controllers.
The FlexCAN driver assumed that FlexCAN controller is big endian for
powerpc architecture and little endian for other architectures.
But this may not be the case. FlexCAN controller can be little or big
endian on any architecture. For e.g. NXP LS1021A ARM based SOC has big
endian FlexCAN controller.
Therefore, the driver has been modified to add a provision for both
types of controllers using an additional device tree property. On a
"fsl,p1010-flexcan" device BE is default, on all other devices LE is.
Big Endian controllers should have "big-endian" set in the device tree.
check "Documentation/devicetree/bindings/net/can/fsl-flexcan.txt" for
usage.
This is the standard practice followed in linux. for more info check:
Documentation/devicetree/bindings/common-properties.txt
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Sakar Arora <Sakar.Arora@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Enable FLEXCAN_QUIRK_BROKEN_WERR_STATE and
FLEXCAN_QUIRK_BROKEN_PERR_STATE for p1010 to report correct state
transitions.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX28 to report correct
state transitions, especially to error passive.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX6 to report correct state
transitions.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add FLEXCAN_QUIRK_BROKEN_PERR_STATE for better description of the
missing error passive interrupt quirk.
Error interrupt flooding may happen if the broken error state quirk fix
is enabled. For example, in case there is singled out node on the bus
and the node sends a frame, then error interrupt flooding happens and
will not stop because the node cannot go to bus off. The flooding will
stop after another node connected to the bus again.
If high bitrate configured on the low end system, then the flooding
may causes performance issue, hence, this patch mitigates this by:
1. disable error interrupt upon error passive state transition
2. re-enable error interrupt upon error warning state transition
3. disable/enable error interrupt upon error active state transition
depends on FLEXCAN_QUIRK_BROKEN_WERR_STATE
In this way, the driver is still able to report correct state
transitions without additional latency. When there are bus problems,
flooding of error interrupts is limited to the number of frames required
to change state from error warning to error passive if the core has
[TR]WRN_INT connected (FLEXCAN_QUIRK_BROKEN_WERR_STATE is not enabled),
otherwise, the flooding is limited to the number of frames required to
change state from error active to error passive.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Rename FLEXCAN_QUIRK_BROKEN_ERR_STATE to FLEXCAN_QUIRK_BROKEN_WERR_STATE
for better description of the missing [TR]WRN_INT quirk.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Update state upon any interrupt to report correct state transitions in
case the flexcan core enabled the broken error state quirk fix.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes the typo "Disble" -> "Disable".
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch switches the imx6 and vf610 based SoCs from the hardware FIFO
to the timestamp based rx offloading.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The flexcan IP core has 64 mailboxes. For now they are configured for
RX as a hardware FIFO. This FIFO has a fixed depth of 6 CAN frames. In
some high load scenarios it turns out thas this buffer is too small.
In order to have a buffer larger than the 6 frames FIFO, this patch adds
support for timestamp based offloading via the generic rx-offload
infrastructure.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In order to receive RTR frames in the non HW FIFO mode the RSS and EACEN bits
of the reg_ctrl2 have to be activated. As this has no side effect in the FIFO
mode, we do this unconditionally on cores with the reg_ctrl2.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Modern flexcan IP cores support two RX modes. One is using the 6 fames deep
hardware FIFO, the other is using up to 64 mailboxes (in non FIFO mode). For
now only the HW FIFO mode is activated.
In order to make use of the RX mailboxes the individual RX masking feature has
to be activated, otherwise matching mailboxes are overwritten during the
reception process. This however switches on the individual RX masking, which
uses reg_rximr registers for masking.
This patch activates the individual RX masking feature unconditionally and
initializes the mask registers (reg_rximr) with 0x0 == "don't care", which
switches off any filtering.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch converts the flexcan driver to make use of the rx-offload
can_rx_offload_irq_offload_fifo() helper function. The idea is to read
the CAN frames already in the interrupt context, as the depth of the
flexcan HW FIFO is too shallow, resulting in too many missed frames.
During a normal NAPI poll the frames are the pushed into the upper
layers.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch makes the TX mailbox selectable duing runtime. This is a preparation
patch to use of the hardware FIFO selectable via runtime. As the TX mailbox
number is different in HW FIFO and normal mode.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch converts the define FLEXCAN_IFLAG_DEFAULT into the runtime
calculated value priv->reg_imask1_default. This is a preparation patch to make
the TX mailbox selectable during runtime, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch folds in the do_bus_err() function into
flexcan_poll_bus_err().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
rx_state, tx_state
This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch changes the declaration of the devtype data to const.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removes the write only member pdata from the struct
flexcan_priv.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds some missing register definitions, which are needed in an
upcoming patch.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396ba
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On a imx6ul-pico board the following error is seen during system suspend:
dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110
PM: Device 2090000.flexcan failed to resume: error -110
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187
the assignment of the error location in CAN error messages had some bit wise
overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines
a single value which points to a location inside the CAN frame on the wire.
This patch fixes the assignments for the error locations in error messages.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch defers the writing of the interrupts bits of the CTRL register order
to enables all interrupts atomically at the the of the flexcan_chip_start()
function.
Suggested-by: Torsten Lang <torsten.lang@uweschneider.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch gives the member of flexcan_priv holding mailboxes a sensible name,
by renaming from "cantxfg" to "mb":
struct flexcan_priv::cantxfg -> struct flexcan_priv::mb
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
address space
This patch renames the pointer to the mmio address space from "base" to "regs"
and changes the type from "void __iomem *" to "struct flexcan_regs __iomem *".
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch renames the "features" member of struct flexcan_devtype_data to
"quirks". The corresponding defines are renamed too, to reflect what they
actually do.
FLEXCAN_HAS_V10_FEATURES -> FLEXCAN_QUIRK_DISABLE_RXFG
FLEXCAN_HAS_BROKEN_ERR_STATE -> FLEXCAN_QUIRK_BROKEN_ERR_STATE
FLEXCAN_HAS_MECR_FEATURES -> FLEXCAN_QUIRK_DISABLE_MECR
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch changes the order the individual bits of the mcr register in
flexcan_chip_start() are or'ed together to match the datasheet. The inline
documentation is adjusted accordingly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removes unused header files from the flexcan driver.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes up the coding style to make checkpatch happier. Some typos are
also fixed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This message isn't really helpful for the general reader of the kernel
logs, so should not be printed with info level. All other register
programming outputs in the flexcan driver already use the debug level.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch replaces a open coded variant of a "mailbox code" definition by an
existing define, improves code readability.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is done to mach the abbreviationin of the register in the datasheets.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds a short documentation snippet about the mailbox organization as
it's regularly not correct in freescale's datasheets.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Flexcan V10 and newer are able to receive RTR frames in a MB. Older versions
are not. Those should use flexcan in FIFO mode.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Making sure that the bus-off state gets passed to can_change_state().
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removes the unused variable "struct net_device *dev" from the
"struct flexcan_priv".
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
Replacing error state change handling with the new mechanism.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
