Age | Commit message (Collapse) | Author | Files | Lines |
|
Commit d5410ac7b0ba ("net:bonding:support balance-alb interface
with vlan to bridge") introduced a reference count leak by not releasing
the reference acquired by ip_dev_find(). Remedy this by insuring the
reference is released.
Fixes: d5410ac7b0ba ("net:bonding:support balance-alb interface with vlan to bridge")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/26758.1660194413@famine
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, tls_device_down synchronizes with tls_device_resync_rx using
RCU, however, the pointer to netdev is stored using WRITE_ONCE and
loaded using READ_ONCE.
Although such approach is technically correct (rcu_dereference is
essentially a READ_ONCE, and rcu_assign_pointer uses WRITE_ONCE to store
NULL), using special RCU helpers for pointers is more valid, as it
includes additional checks and might change the implementation
transparently to the callers.
Mark the netdev pointer as __rcu and use the correct RCU helpers to
access it. For non-concurrent access pass the right conditions that
guarantee safe access (locks taken, refcount value). Also use the
correct helper in mlx5e, where even READ_ONCE was missing.
The transition to RCU exposes existing issues, fixed by this commit:
1. bond_tls_device_xmit could read netdev twice, and it could become
NULL the second time, after the NULL check passed.
2. Drivers shouldn't stop processing the last packet if tls_device_down
just set netdev to NULL, before tls_dev_del was called. This prevents a
possible packet drop when transitioning to the fallback software mode.
Fixes: 89df6a810470 ("net/bonding: Implement TLS TX device offload")
Fixes: c55dcdd435aa ("net/tls: Fix use-after-free after the TLS device goes down and up")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Link: https://lore.kernel.org/r/20220810081602.1435800-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In my test, balance-alb bonding with two slaves eth0 and eth1,
and then Bond0.150 is created with vlan id attached bond0.
After adding bond0.150 into one linux bridge, I noted that Bond0,
bond0.150 and bridge were assigned to the same MAC as eth0.
Once bond0.150 receives a packet whose dest IP is bridge's
and dest MAC is eth1's, the linux bridge will not match
eth1's MAC entry in FDB, and not handle it as expected.
The patch fix the issue, and diagram as below:
eth1(mac:eth1_mac)--bond0(balance-alb,mac:eth0_mac)--eth0(mac:eth0_mac)
|
bond0.150(mac:eth0_mac)
|
bridge(ip:br_ip, mac:eth0_mac)--other port
Suggested-by: Hu Yadi <huyd12@chinatelecom.cn>
Signed-off-by: Sun Shouxin <sunshouxin@chinatelecom.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bonding driver piggybacks on time stamps kept by the network stack
for the purpose of the netdev TX watchdog, and this is problematic
because it does not work with NETIF_F_LLTX devices.
It is hard to say why the driver looks at dev_trans_start() of the
slave->dev, considering that this is updated even by non-ARP/NS probes
sent by us, and even by traffic not sent by us at all (for example PTP
on physical slave devices). ARP monitoring in active-backup mode appears
to still work even if we track only the last TX time of actual ARP
probes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1db ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e33a ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
commit 0622cab0341c ("bonding: fix 802.3ad aggregator reselection"),
resolve case, when there is several aggregation groups in the same bond.
bond_3ad_unbind_slave will invalidate (clear) aggregator when
__agg_active_ports return zero. So, ad_clear_agg can be executed even, when
num_of_ports!=0. Than bond_3ad_unbind_slave can be executed again for,
previously cleared aggregator. NOTE: at this time bond_3ad_unbind_slave
will not update slave ports list, because lag_ports==NULL. So, here we
got slave ports, pointing to freed aggregator memory.
Fix with checking actual number of ports in group (as was before
commit 0622cab0341c ("bonding: fix 802.3ad aggregator reselection") ),
before ad_clear_agg().
The KASAN logs are as follows:
[ 767.617392] ==================================================================
[ 767.630776] BUG: KASAN: use-after-free in bond_3ad_state_machine_handler+0x13dc/0x1470
[ 767.638764] Read of size 2 at addr ffff00011ba9d430 by task kworker/u8:7/767
[ 767.647361] CPU: 3 PID: 767 Comm: kworker/u8:7 Tainted: G O 5.15.11 #15
[ 767.655329] Hardware name: DNI AmazonGo1 A7040 board (DT)
[ 767.660760] Workqueue: lacp_1 bond_3ad_state_machine_handler
[ 767.666468] Call trace:
[ 767.668930] dump_backtrace+0x0/0x2d0
[ 767.672625] show_stack+0x24/0x30
[ 767.675965] dump_stack_lvl+0x68/0x84
[ 767.679659] print_address_description.constprop.0+0x74/0x2b8
[ 767.685451] kasan_report+0x1f0/0x260
[ 767.689148] __asan_load2+0x94/0xd0
[ 767.692667] bond_3ad_state_machine_handler+0x13dc/0x1470
Fixes: 0622cab0341c ("bonding: fix 802.3ad aggregator reselection")
Co-developed-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220629012914.361-1-yevhen.orlov@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot has two reports involving the same root cause.
bond_alb_initialize() must not set bond->alb_info.rlb_enabled
if a memory allocation error is detected.
Report 1:
general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 0 PID: 12276 Comm: kworker/u4:10 Not tainted 5.19.0-rc3-syzkaller-00132-g3b89b511ea0c #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
RIP: 0010:rlb_clear_slave+0x10e/0x690 drivers/net/bonding/bond_alb.c:393
Code: 8e fc 83 fb ff 0f 84 74 02 00 00 e8 cc 2a 8e fc 48 8b 44 24 08 89 dd 48 c1 e5 06 4c 8d 34 28 49 8d 7e 14 48 89 f8 48 c1 e8 03 <42> 0f b6 14 20 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85
RSP: 0018:ffffc90018a8f678 EFLAGS: 00010203
RAX: 0000000000000002 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88803375bb00 RSI: ffffffff84ec4ac4 RDI: 0000000000000014
RBP: 0000000000000000 R08: 0000000000000005 R09: 00000000ffffffff
R10: 0000000000000000 R11: 0000000000000000 R12: dffffc0000000000
R13: ffff8880ac889000 R14: 0000000000000000 R15: ffff88815a668c80
FS: 0000000000000000(0000) GS:ffff8880b9a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005597077e10b0 CR3: 0000000026668000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
bond_alb_deinit_slave+0x43c/0x6b0 drivers/net/bonding/bond_alb.c:1663
__bond_release_one.cold+0x383/0xd53 drivers/net/bonding/bond_main.c:2370
bond_slave_netdev_event drivers/net/bonding/bond_main.c:3778 [inline]
bond_netdev_event+0x993/0xad0 drivers/net/bonding/bond_main.c:3889
notifier_call_chain+0xb5/0x200 kernel/notifier.c:87
call_netdevice_notifiers_info+0xb5/0x130 net/core/dev.c:1945
call_netdevice_notifiers_extack net/core/dev.c:1983 [inline]
call_netdevice_notifiers net/core/dev.c:1997 [inline]
unregister_netdevice_many+0x948/0x18b0 net/core/dev.c:10839
default_device_exit_batch+0x449/0x590 net/core/dev.c:11333
ops_exit_list+0x125/0x170 net/core/net_namespace.c:167
cleanup_net+0x4ea/0xb00 net/core/net_namespace.c:594
process_one_work+0x996/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e9/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:302
</TASK>
Report 2:
general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
CPU: 1 PID: 5206 Comm: syz-executor.1 Not tainted 5.18.0-syzkaller-12108-g58f9d52ff689 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:rlb_req_update_slave_clients+0x109/0x2f0 drivers/net/bonding/bond_alb.c:502
Code: 5d 18 8f fc 41 80 3e 00 0f 85 a5 01 00 00 89 d8 48 c1 e0 06 49 03 84 24 68 01 00 00 48 8d 78 30 49 89 c7 48 89 fa 48 c1 ea 03 <80> 3c 2a 00 0f 85 98 01 00 00 4d 39 6f 30 75 83 e8 22 18 8f fc 49
RSP: 0018:ffffc9000300ee80 EFLAGS: 00010206
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffc90016c11000
RDX: 0000000000000006 RSI: ffffffff84eb6bf3 RDI: 0000000000000030
RBP: dffffc0000000000 R08: 0000000000000005 R09: 00000000ffffffff
R10: 0000000000000000 R11: 0000000000000000 R12: ffff888027c80c80
R13: ffff88807d7ff800 R14: ffffed1004f901bd R15: 0000000000000000
FS: 00007f6f46c58700(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020010000 CR3: 00000000516cc000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
alb_fasten_mac_swap+0x886/0xa80 drivers/net/bonding/bond_alb.c:1070
bond_alb_handle_active_change+0x624/0x1050 drivers/net/bonding/bond_alb.c:1765
bond_change_active_slave+0xfa1/0x29b0 drivers/net/bonding/bond_main.c:1173
bond_select_active_slave+0x23f/0xa50 drivers/net/bonding/bond_main.c:1253
bond_enslave+0x3b34/0x53b0 drivers/net/bonding/bond_main.c:2159
do_set_master+0x1c8/0x220 net/core/rtnetlink.c:2577
rtnl_newlink_create net/core/rtnetlink.c:3380 [inline]
__rtnl_newlink+0x13ac/0x17e0 net/core/rtnetlink.c:3580
rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3593
rtnetlink_rcv_msg+0x43a/0xc90 net/core/rtnetlink.c:6089
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2501
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x917/0xe10 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
____sys_sendmsg+0x6eb/0x810 net/socket.c:2492
___sys_sendmsg+0xf3/0x170 net/socket.c:2546
__sys_sendmsg net/socket.c:2575 [inline]
__do_sys_sendmsg net/socket.c:2584 [inline]
__se_sys_sendmsg net/socket.c:2582 [inline]
__x64_sys_sendmsg+0x132/0x220 net/socket.c:2582
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f6f45a89109
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6f46c58168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f6f45b9c030 RCX: 00007f6f45a89109
RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000006
RBP: 00007f6f45ae308d R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffed99029af R14: 00007f6f46c58300 R15: 0000000000022000
</TASK>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220627102813.126264-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add per port priority support for bonding active slave re-selection during
failover. A higher number means higher priority in selection. The primary
slave still has the highest priority. This option also follows the
primary_reselect rules.
This option could only be configured via netlink.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bonding ARP monitor fails to decrement send_peer_notif, the
number of peer notifications (gratuitous ARP or ND) to be sent. This
results in a continuous series of notifications.
Correct this by decrementing the counter for each notification.
Reported-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Fixes: b0929915e035 ("bonding: Fix RTNL: assertion failed at net/core/rtnetlink.c for ab arp monitor")
Link: https://lore.kernel.org/netdev/b2fd4147-8f50-bebd-963a-1a3e8d1d9715@redhat.com/
Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/9400.1655407960@famine
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Setting RLB_NULL_INDEX is not needed as this is done in bond_alb_initialize
which is called by bond_open.
Also reduce the number of rtnl_unlock calls by just using the standard
goto cleanup path.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for reporting errors via extack in both bond_newlink
and bond_changelink.
Instead of having to look in the kernel log for why an option was not
correct just report the error to the user via the extack variable.
What is currently reported today:
ip link add bond0 type bond
ip link set bond0 up
ip link set bond0 type bond mode 4
RTNETLINK answers: Device or resource busy
After this change:
ip link add bond0 type bond
ip link set bond0 up
ip link set bond0 type bond mode 4
Error: unable to set option because the bond is up.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Guard ns_targets in struct bond_params by CONFIG_IPV6, which could save
256 bytes if IPv6 not configed. Also add this protection for function
bond_is_ip6_target_ok() and bond_get_targets_ip6().
Remove the IS_ENABLED() check for bond_opts[] as this will make
BOND_OPT_NS_TARGETS uninitialized if CONFIG_IPV6 not enabled. Add
a dummy bond_option_ns_ip6_targets_set() for this situation.
Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20220531063727.224043-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When adding bond new parameter ns_targets. I forgot to print this
in bond master proc info. After updating, the bond master info will look
like:
ARP IP target/s (n.n.n.n form): 192.168.1.254
NS IPv6 target/s (XX::XX form): 2022::1, 2022::2
Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Reported-by: Li Liang <liali@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20220530062639.37179-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When setting bond NS target, we use bond_is_ip6_target_ok() to check
if the address valid. The link local address was wrongly rejected in
bond_changelink(), as most time the user just set the ARP/NS target to
gateway, while the IPv6 gateway is always a link local address when user
set up interface via SLAAC.
So remove the link local addr check when setting bond NS target.
Fixes: 129e3c1bab24 ("bonding: add new option ns_ip6_target")
Reported-by: Li Liang <liali@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ethernet/cadence/macb_main.c
5cebb40bc955 ("net: macb: Fix PTP one step sync support")
138badbc21a0 ("net: macb: use NAPI for TX completion path")
https://lore.kernel.org/all/20220523111021.31489367@canb.auug.org.au/
net/smc/af_smc.c
75c1edf23b95 ("net/smc: postpone sk_refcnt increment in connect()")
3aba103006bc ("net/smc: align the connect behaviour with TCP")
https://lore.kernel.org/all/20220524114408.4bf1af38@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When removing the rcu_read_lock in bond_ethtool_get_ts_info() as
discussed [1], I didn't notice it could be called via setsockopt,
which doesn't hold rcu lock, as syzbot pointed:
stack backtrace:
CPU: 0 PID: 3599 Comm: syz-executor317 Not tainted 5.18.0-rc5-syzkaller-01392-g01f4685797a5 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
bond_option_active_slave_get_rcu include/net/bonding.h:353 [inline]
bond_ethtool_get_ts_info+0x32c/0x3a0 drivers/net/bonding/bond_main.c:5595
__ethtool_get_ts_info+0x173/0x240 net/ethtool/common.c:554
ethtool_get_phc_vclocks+0x99/0x110 net/ethtool/common.c:568
sock_timestamping_bind_phc net/core/sock.c:869 [inline]
sock_set_timestamping+0x3a3/0x7e0 net/core/sock.c:916
sock_setsockopt+0x543/0x2ec0 net/core/sock.c:1221
__sys_setsockopt+0x55e/0x6a0 net/socket.c:2223
__do_sys_setsockopt net/socket.c:2238 [inline]
__se_sys_setsockopt net/socket.c:2235 [inline]
__x64_sys_setsockopt+0xba/0x150 net/socket.c:2235
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f8902c8eb39
Fix it by adding rcu_read_lock and take a ref on the real_dev.
Since dev_hold() and dev_put() can take NULL these days, we can
skip checking if real_dev exist.
[1] https://lore.kernel.org/netdev/27565.1642742439@famine/
Reported-by: syzbot+92beb3d46aab498710fa@syzkaller.appspotmail.com
Fixes: aa6034678e87 ("bonding: use rcu_dereference_rtnl when get bonding active slave")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220519020148.1058344-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drivers should call the TSO setting helper, GSO is controllable
by user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch replaces some sk_ipv6only tests with ipv6_only_sock().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b5f862180d70 was introduced to discard lowest hash bit for layer3+4 hashing
but it also removes last bit from non layer3+4 hashing
Below script shows layer2+3 hashing will result in same slave to be used with above commit.
$ cat hash.py
#/usr/bin/python3.6
h_dests=[0xa0, 0xa1]
h_source=0xe3
hproto=0x8
saddr=0x1e7aa8c0
daddr=0x17aa8c0
for h_dest in h_dests:
hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
hash ^= hash >> 16
hash ^= hash >> 8
print(hash)
print("with last bit removed")
for h_dest in h_dests:
hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
hash ^= hash >> 16
hash ^= hash >> 8
hash = hash >> 1
print(hash)
Output:
$ python3.6 hash.py
522133332
522133333 <-------------- will result in both slaves being used
with last bit removed
261066666
261066666 <-------------- only single slave used
Signed-off-by: suresh kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before adding yet another possibly contended atomic_long_t,
it is time to add per-cpu storage for existing ones:
dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler
Because many devices do not have to increment such counters,
allocate the per-cpu storage on demand, so that dev_get_stats()
does not have to spend considerable time folding zero counters.
Note that some drivers have abused these counters which
were supposed to be only used by core networking stack.
v4: should use per_cpu_ptr() in dev_get_stats() (Jakub)
v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo)
v2: add a missing include (reported by kernel test robot <lkp@intel.com>)
Change in netdev_core_stats_alloc() (Jakub)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: jeffreyji <jeffreyji@google.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Lianjie Zhang <zhanglianjie@uniontech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add a new bonding option ns_ip6_target, which correspond
to the arp_ip_target. With this we set IPv6 targets and send IPv6 NS
request to determine the health of the link.
For other related options like the validation, we still use
arp_validate, and will change to ns_validate later.
Note: the sysfs configuration support was removed based on
https://lore.kernel.org/netdev/8863.1645071997@famine
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new bonding parameter ns_targets to store IPv6 address.
Add required bond_ns_send/rcv functions first before adding
IPv6 address option setting.
Add two functions bond_send/rcv_validate so we can send/recv
ARP and NS at the same time.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function bond_handle_vlan() is split from bond_arp_send() for later
IPv6 usage.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In __bond_release_one(), bond_set_carrier() is only called when bond
device has no slave. Therefore, if we remove the up slave from a master
with two slaves and keep the down slave, the master will remain up.
Fix this by moving bond_set_carrier() out of if (!bond_has_slaves(bond))
statement.
Reproducer:
$ insmod bonding.ko mode=0 miimon=100 max_bonds=2
$ ifconfig bond0 up
$ ifenslave bond0 eth0 eth1
$ ifconfig eth0 down
$ ifenslave -d bond0 eth1
$ cat /proc/net/bonding/bond0
Fixes: ff59c4563a8d ("[PATCH] bonding: support carrier state for master")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/1645021088-38370-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported that two threads might write over agg_select_timer
at the same time. Make agg_select_timer atomic to fix the races.
BUG: KCSAN: data-race in bond_3ad_initiate_agg_selection / bond_3ad_state_machine_handler
read to 0xffff8881242aea90 of 4 bytes by task 1846 on cpu 1:
bond_3ad_state_machine_handler+0x99/0x2810 drivers/net/bonding/bond_3ad.c:2317
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
write to 0xffff8881242aea90 of 4 bytes by task 25910 on cpu 0:
bond_3ad_initiate_agg_selection+0x18/0x30 drivers/net/bonding/bond_3ad.c:1998
bond_open+0x658/0x6f0 drivers/net/bonding/bond_main.c:3967
__dev_open+0x274/0x3a0 net/core/dev.c:1407
dev_open+0x54/0x190 net/core/dev.c:1443
bond_enslave+0xcef/0x3000 drivers/net/bonding/bond_main.c:1937
do_set_master net/core/rtnetlink.c:2532 [inline]
do_setlink+0x94f/0x2500 net/core/rtnetlink.c:2736
__rtnl_newlink net/core/rtnetlink.c:3414 [inline]
rtnl_newlink+0xfeb/0x13e0 net/core/rtnetlink.c:3529
rtnetlink_rcv_msg+0x745/0x7e0 net/core/rtnetlink.c:5594
netlink_rcv_skb+0x14e/0x250 net/netlink/af_netlink.c:2494
rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:5612
netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
netlink_unicast+0x602/0x6d0 net/netlink/af_netlink.c:1343
netlink_sendmsg+0x728/0x850 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmsg+0x195/0x230 net/socket.c:2496
__do_sys_sendmsg net/socket.c:2505 [inline]
__se_sys_sendmsg net/socket.c:2503 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2503
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00000050 -> 0x0000004f
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 25910 Comm: syz-executor.1 Tainted: G W 5.17.0-rc4-syzkaller-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
cleanup_net() is competing with other rtnl users.
Batching bond_net_exit() factorizes all rtnl acquistions
to a single one, giving chance for cleanup_net()
to progress much faster, holding rtnl a bit longer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When 803.2ad mode enables a participating port, it should update
the slave-array. I have observed that the member links are participating
and are part of the active aggregator while the traffic is egressing via
only one member link (in a case where two links are participating). Via
kprobes I discovered that slave-arr has only one link added while
the other participating link wasn't part of the slave-arr.
I couldn't see what caused that situation but the simple code-walk
through provided me hints that the enable_port wasn't always associated
with the slave-array update.
Fixes: ee6377147409 ("bonding: Simplify the xmit function for modes that use xmit_hash")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220207222901.1795287-1-maheshb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nothing in ipv6.h needs ndisc.h, drop it.
Link: https://lore.kernel.org/r/20220203043457.2222388-1-kuba@kernel.org
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Link: https://lore.kernel.org/r/20220203231240.2297588-1-kuba@kernel.org
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since ipv6 neighbor solicitation and advertisement messages
isn't handled gracefully in bond6 driver, we can see packet
drop due to inconsistency between mac address in the option
message and source MAC .
Another examples is ipv6 neighbor solicitation and advertisement
messages from VM via tap attached to host bridge, the src mac
might be changed through balance-alb mode, but it is not synced
with Link-layer address in the option message.
The patch implements bond6's tx handle for ipv6 neighbor
solicitation and advertisement messages.
Suggested-by: Hu Yadi <huyd12@chinatelecom.cn>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Sun Shouxin <sunshouxin@chinatelecom.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter and can.
Current release - new code bugs:
- tcp: add a missing sk_defer_free_flush() in tcp_splice_read()
- tcp: add a stub for sk_defer_free_flush(), fix CONFIG_INET=n
- nf_tables: set last expression in register tracking area
- nft_connlimit: fix memleak if nf_ct_netns_get() fails
- mptcp: fix removing ids bitmap setting
- bonding: use rcu_dereference_rtnl when getting active slave
- fix three cases of sleep in atomic context in drivers: lan966x, gve
- handful of build fixes for esoteric drivers after netdev->dev_addr
was made const
Previous releases - regressions:
- revert "ipv6: Honor all IPv6 PIO Valid Lifetime values", it broke
Linux compatibility with USGv6 tests
- procfs: show net device bound packet types
- ipv4: fix ip option filtering for locally generated fragments
- phy: broadcom: hook up soft_reset for BCM54616S
Previous releases - always broken:
- ipv4: raw: lock the socket in raw_bind()
- ipv4: decrease the use of shared IPID generator to decrease the
chance of attackers guessing the values
- procfs: fix cross-netns information leakage in /proc/net/ptype
- ethtool: fix link extended state for big endian
- bridge: vlan: fix single net device option dumping
- ping: fix the sk_bound_dev_if match in ping_lookup"
* tag 'net-5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
net: bridge: vlan: fix memory leak in __allowed_ingress
net: socket: rename SKB_DROP_REASON_SOCKET_FILTER
ipv4: remove sparse error in ip_neigh_gw4()
ipv4: avoid using shared IP generator for connected sockets
ipv4: tcp: send zero IPID in SYNACK messages
ipv4: raw: lock the socket in raw_bind()
MAINTAINERS: add missing IPv4/IPv6 header paths
MAINTAINERS: add more files to eth PHY
net: stmmac: dwmac-sun8i: use return val of readl_poll_timeout()
net: bridge: vlan: fix single net device option dumping
net: stmmac: skip only stmmac_ptp_register when resume from suspend
net: stmmac: configure PTP clock source prior to PTP initialization
Revert "ipv6: Honor all IPv6 PIO Valid Lifetime values"
connector/cn_proc: Use task_is_in_init_pid_ns()
pid: Introduce helper task_is_in_init_pid_ns()
gve: Fix GFP flags when allocing pages
net: lan966x: Fix sleep in atomic context when updating MAC table
net: lan966x: Fix sleep in atomic context when injecting frames
ethernet: seeq/ether3: don't write directly to netdev->dev_addr
ethernet: 8390/etherh: don't write directly to netdev->dev_addr
...
|
|
bond_option_active_slave_get_rcu() should not be used in rtnl_mutex as it
use rcu_dereference(). Replace to rcu_dereference_rtnl() so we also can use
this function in rtnl protected context.
With this update, we can rmeove the rcu_read_lock/unlock in
bonding .ndo_eth_ioctl and .get_ts_info.
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP ioctl to active device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove PDE_DATA() completely and replace it with pde_data().
[akpm@linux-foundation.org: fix naming clash in drivers/nubus/proc.c]
[akpm@linux-foundation.org: now fix it properly]
Link: https://lkml.kernel.org/r/20211124081956.87711-2-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alexey Gladkov <gladkov.alexey@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Wrong hash sends single stream to multiple output interfaces.
The offset calculation was relative to skb->head, fix it to be relative
to skb->data.
Fixes: a815bde56b15 ("net, bonding: Refactor bond_xmit_hash for use with
xdp_buff")
Reviewed-by: Jussi Maki <joamaki@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Moshe Tal <moshet@nvidia.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Linux bonding scenario, one packet is copied to several copies and sent
by all slave device of bond0 in mode 3(broadcast mode). The mode 3 xmit
function bond_xmit_broadcast() only ueses the last slave device's tx result
as the final result. In this case, if the last slave device is down, then
it always return NET_XMIT_DROP, even though the other slave devices xmit
success. It may cause the tx statistics error, and cause the application
(e.g. scp) consider the network is unreachable.
For example, use the following command to configure server A.
echo 3 > /sys/class/net/bond0/bonding/mode
ifconfig bond0 up
ifenslave bond0 eth0 eth1
ifconfig bond0 192.168.1.125
ifconfig eth0 up
ifconfig eth1 down
The slave device eth0 and eth1 are connected to server B(192.168.1.107).
Run the ping 192.168.1.107 -c 3 -i 0.2 command, the following information
is displayed.
PING 192.168.1.107 (192.168.1.107) 56(84) bytes of data.
64 bytes from 192.168.1.107: icmp_seq=1 ttl=64 time=0.077 ms
64 bytes from 192.168.1.107: icmp_seq=2 ttl=64 time=0.056 ms
64 bytes from 192.168.1.107: icmp_seq=3 ttl=64 time=0.051 ms
192.168.1.107 ping statistics
0 packets transmitted, 3 received
Actually, the slave device eth0 of the bond successfully sends three
ICMP packets, but the result shows that 0 packets are transmitted.
Also if we use scp command to get remote files, the command end with the
following printings.
ssh_exchange_identification: read: Connection timed out
So this patch modifies the bond_xmit_broadcast to return NET_XMIT_SUCCESS
if one slave device in the bond sends packets successfully. If all slave
devices send packets fail, the discarded packets stats is increased. The
skb is released when there is no slave device in the bond or the last slave
device is down.
Fixes: ae46f184bc1f ("bonding: propagate transmit status")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the userspace program is distributed in binary form (distro package),
there is no way to know on which kernel versions it will run.
Let's only check if the flag was set when do SIOCSHWTSTAMP. And return
hwtstamp_config with flag HWTSTAMP_FLAG_BONDED_PHC_INDEX to notify
userspace whether the new feature is supported or not.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Fixes: 085d61000845 ("Bonding: force user to add HWTSTAMP_FLAG_BONDED_PHC_INDEX when get/set HWTSTAMP")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
|
|
include/net/sock.h
commit 8f905c0e7354 ("inet: fully convert sk->sk_rx_dst to RCU rules")
commit 43f51df41729 ("net: move early demux fields close to sk_refcnt")
https://lore.kernel.org/all/20211222141641.0caa0ab3@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When 802.3ad bond mode is configured the ad_actor_system option is set to
"00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors'
system address it was failing with EINVAL.
An all-zeroes ethernet address is valid, only multicast addresses are not
valid values.
Fixes: 171a42c38c6e ("bonding: add netlink support for sys prio, actor sys mac, and port key")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20211221111345.2462-1-ffmancera@riseup.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When there is a failover, the PHC index of bond active interface will be
changed. This may break the user space program if the author didn't aware.
By setting this flag, the user should aware that the PHC index get/set
by syscall is not stable. And the user space is able to deal with it.
Without this flag, the kernel will reject the request forwarding to
bonding.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Fixes: 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP ioctl to active device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently "bond_should_notify_peers: slave ..." messages are printed whenever
"bond_should_notify_peers" function is called.
+++
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:26 node1 kernel: bond0: (slave enp0s25): Received LACPDU on port 1
Dec 12 12:33:26 node1 kernel: bond0: (slave enp0s25): Rx Machine: Port=1, Last State=6, Curr State=6
Dec 12 12:33:26 node1 kernel: bond0: (slave enp0s25): partner sync=1
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
...
Dec 12 12:33:30 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:30 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:30 node1 kernel: bond0: (slave enp4s3): Received LACPDU on port 2
Dec 12 12:33:30 node1 kernel: bond0: (slave enp4s3): Rx Machine: Port=2, Last State=6, Curr State=6
Dec 12 12:33:30 node1 kernel: bond0: (slave enp4s3): partner sync=1
Dec 12 12:33:30 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:30 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:30 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
+++
This is confusing and can also clutter up debug logs.
Print logs only when the peer notification happens.
Signed-off-by: Suresh Kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KCSAN reported a data-race [1] around tx_rebalance_counter
which can be accessed from different contexts, without
the protection of a lock/mutex.
[1]
BUG: KCSAN: data-race in bond_alb_init_slave / bond_alb_monitor
write to 0xffff888157e8ca24 of 4 bytes by task 7075 on cpu 0:
bond_alb_init_slave+0x713/0x860 drivers/net/bonding/bond_alb.c:1613
bond_enslave+0xd94/0x3010 drivers/net/bonding/bond_main.c:1949
do_set_master net/core/rtnetlink.c:2521 [inline]
__rtnl_newlink net/core/rtnetlink.c:3475 [inline]
rtnl_newlink+0x1298/0x13b0 net/core/rtnetlink.c:3506
rtnetlink_rcv_msg+0x745/0x7e0 net/core/rtnetlink.c:5571
netlink_rcv_skb+0x14e/0x250 net/netlink/af_netlink.c:2491
rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:5589
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x5fc/0x6c0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x6e1/0x7d0 net/netlink/af_netlink.c:1916
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmsg+0x195/0x230 net/socket.c:2492
__do_sys_sendmsg net/socket.c:2501 [inline]
__se_sys_sendmsg net/socket.c:2499 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2499
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff888157e8ca24 of 4 bytes by task 1082 on cpu 1:
bond_alb_monitor+0x8f/0xc00 drivers/net/bonding/bond_alb.c:1511
process_one_work+0x3fc/0x980 kernel/workqueue.c:2298
worker_thread+0x616/0xa70 kernel/workqueue.c:2445
kthread+0x2c7/0x2e0 kernel/kthread.c:327
ret_from_fork+0x1f/0x30
value changed: 0x00000001 -> 0x00000064
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 1082 Comm: kworker/u4:3 Not tainted 5.16.0-rc3-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: bond1 bond_alb_monitor
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have VLAN PTP support(via get_ts_info) on kernel, and bond support(by
getting active interface via netlink message) on userspace tool linuxptp.
But there are always some users who want to use PTP with VLAN over bond,
which is not able to do with the current implementation.
This patch passed get_ts_info and SIOC[SG]HWTSTAMP ioctl to active device
with bond mode active-backup/tlb/alb. With this users could get kernel native
bond or VLAN over bond PTP support.
Test with ptp4l and it works with VLAN over bond after this patch:
]# ptp4l -m -i bond0.23
ptp4l[53377.141]: selected /dev/ptp4 as PTP clock
ptp4l[53377.142]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[53377.143]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[53377.143]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[53384.127]: port 1: LISTENING to MASTER on ANNOUNCE_RECEIPT_TIMEOUT_EXPIRES
ptp4l[53384.127]: selected local clock e41d2d.fffe.123db0 as best master
ptp4l[53384.127]: port 1: assuming the grand master role
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we use hard code number to verify if we are in the
arp_interval timeslice. But some user may want to reduce/extend
the verify timeslice. With the similar team option 'missed_max'
the uers could change that number based on their own environment.
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev->gso_max_segs is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add netif_set_gso_max_segs() helper.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_segs()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|