summaryrefslogtreecommitdiffstats
path: root/drivers/net/bonding/bond_main.c
AgeCommit message (Collapse)AuthorFilesLines
2017-04-05bonding: attempt to better support longer hw addressesJarod Wilson1-31/+42
People are using bonding over Infiniband IPoIB connections, and who knows what else. Infiniband has a hardware address length of 20 octets (INFINIBAND_ALEN), and the network core defines a MAX_ADDR_LEN of 32. Various places in the bonding code are currently hard-wired to 6 octets (ETH_ALEN), such as the 3ad code, which I've left untouched here. Besides, only alb is currently possible on Infiniband links right now anyway, due to commit 1533e7731522, so the alb code is where most of the changes are. One major component of this change is the addition of a bond_hw_addr_copy function that takes a length argument, instead of using ether_addr_copy everywhere that hardware addresses need to be copied about. The other major component of this change is converting the bonding code from using struct sockaddr for address storage to struct sockaddr_storage, as the former has an address storage space of only 14, while the latter is 128 minus a few, which is necessary to support bonding over device with up to MAX_ADDR_LEN octet hardware addresses. Additionally, this probably fixes up some memory corruption issues with the current code, where it's possible to write an infiniband hardware address into a sockaddr declared on the stack. Lightly tested on a dual mlx4 IPoIB setup, which properly shows a 20-octet hardware address now: $ cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) Bonding Mode: fault-tolerance (active-backup) (fail_over_mac active) Primary Slave: mlx4_ib0 (primary_reselect always) Currently Active Slave: mlx4_ib0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 100 Down Delay (ms): 100 Slave Interface: mlx4_ib0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: 80:00:02:08:fe:80:00:00:00:00:00:00:e4:1d:2d:03:00:1d:67:01 Slave queue ID: 0 Slave Interface: mlx4_ib1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: 80:00:02:09:fe:80:00:00:00:00:00:01:e4:1d:2d:03:00:1d:67:02 Slave queue ID: 0 Also tested with a standard 1Gbps NIC bonding setup (with a mix of e1000 and e1000e cards), running LNST's bonding tests. CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-05bonding: fix active-backup transitionMahesh Bandewar1-8/+5
Earlier patch c4adfc822bf5 ("bonding: make speed, duplex setting consistent with link state") made an attempt to keep slave state consistent with speed and duplex settings. Unfortunately link-state transition is used to change the active link especially when used in conjunction with mii-mon. The above mentioned patch broke that logic. Also when speed and duplex settings for a link are updated during a link-event, the link-status should not be changed to invoke correct transition logic. This patch fixes this issue by moving the link-state update outside of the bond_update_speed_duplex() fn and to the places where this fn is called and update link-state selectively. Fixes: c4adfc822bf5 ("bonding: make speed, duplex setting consistent with link state") Signed-off-by: Mahesh Bandewar <maheshb@google.com> Reviewed-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-30bonding: refine bond_fold_stats() wrap detectionEric Dumazet1-3/+8
Some device drivers reset their stats at down/up events, possibly fooling bonding stats, since they operate with relative deltas. It is nearly not possible to fix drivers, since some of them compute the tx/rx counters based on per rx/tx queue stats, and the queues can be reconfigured (ethtool -L) between the down/up sequence. Lets avoid accumulating 'negative' values that render bonding stats useless. It is better to lose small deltas, assuming the bonding stats are fetched at a reasonable frequency. Fixes: 5f0c5f73e5ef ("bonding: make global bonding stats more reliable") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-27bonding: correctly update link status during mii-commit phaseMahesh Bandewar1-1/+6
bond_miimon_commit() marks the link UP after attempting to get the speed and duplex settings for the link. There is a possibility that bond_update_speed_duplex() could fail. This is another place where it could result into an inconsistent bonding link state. With this patch the link will be marked UP only if the speed and duplex values retrieved have sane values and processed further. Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-27bonding: make speed, duplex setting consistent with link stateMahesh Bandewar1-10/+14
bond_update_speed_duplex() retrieves speed and duplex settings. There is a possibility of failure in retrieving these values but caller has to assume it's always successful. This leads to having inconsistent slave link settings. If these (speed, duplex) values cannot be retrieved, then keeping the link UP causes problems. The updated bond_update_speed_duplex() returns 0 on success if it retrieves sane values for speed and duplex. On failure it returns 1 and marks the link down. Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-27bonding: improve link-status update in mii-monitoringMahesh Bandewar1-9/+9
The primary issue is that mii-inspect phase updates link-state and expects changes to be committed during the mii-commit phase. After the inspect phase if it fails to acquire rtnl-mutex, the commit phase (bond_mii_commit) doesn't get to run. This partially updated state stays and makes the internal-state inconsistent. e.g. setup bond0 => slaves: eth1, eth2 eth1 goes DOWN -> UP mii_monitor() mii-inspect() bond_set_slave_link_state(eth1, UP, DontNotify) rtnl_trylock() <- fails! Next mii-monitor round eth1: No change mii_monitor() mii-inspect() eth1->link == current-status (ethtool_ops->get_link) no-change-detected End result: eth1: Link = BOND_LINK_UP Speed = 0xfffff [SpeedUnknown] Duplex = 0xff [DuplexUnknown] This doesn't always happen but for some unlucky machines in a large set of machines it creates problems. The fix for this is to avoid making changes during inspect phase and postpone them until acquiring the rtnl-mutex / invoking commit phase. Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-09bonding: reduce scope of some global variablesMahesh Bandewar1-6/+5
Many of the bond param variables are declared global while it's not really necessary for these variables to be global. So moving them to the location these are used. Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-09bonding: remove hardcoded valueMahesh Bandewar1-1/+13
Eliminate hard-coded value and use the default that is set. Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-09bonding: initialize work-queues during creation of bondMahesh Bandewar1-2/+2
Initializing work-queues every time ifup operation performed is unnecessary and can be performed only once when the port is created. Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-09bonding: restructure arp-monitorMahesh Bandewar1-10/+14
In preparation to move the work-queue initialization to port creation from current port_open phase. Work-queue initialization does not make sense every time we do 'ifup/ifdown'. So moving to port creation phase. Arp monitoring work depends on the bonding mode and that is not tied to the port creation and can change anytime during the life after port creation. So this restructuring allows us to move the initialization at creation without losing the ability to arm the correct work for the mode user has selected. Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-02bonding: use ETH_MAX_MTU as max mtuWANG Cong1-0/+1
This restores the ability of setting bond device's mtu to 9000. Fixes: 91572088e3fd ("net: use core MTU range checking in core net infra") Reported-by: daznis@gmail.com Reported-by: Brad Campbell <lists2009@fnarfbargle.com> Cc: Jarod Wilson <jarod@redhat.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-06net: remove ndo_neigh_{construct, destroy} from stacked devicesIdo Schimmel1-2/+0
In commit 18bfb924f000 ("net: introduce default neigh_construct/destroy ndo calls for L2 upper devices") we added these ndos to stacked devices such as team and bond, so that calls will be propagated to mlxsw. However, previous commit removed the reliance on these ndos and no new users of these ndos have appeared since above mentioned commit. We can therefore safely remove this dead code. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-03bonding: Remove unnecessary returned value checkZhu Yanjun1-6/+4
The function bond_info_query alwarys returns 0. As such, in the function bond_do_ioctl, it is not necessary to check the returned value. So the interface type of the function bond_info_query is changed to void. The redundant check is removed. Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-08net: make ndo_get_stats64 a void functionstephen hemminger1-6/+4
The network device operation for reading statistics is only called in one place, and it ignores the return value. Having a structure return value is potentially confusing because some future driver could incorrectly assume that the return value was used. Fix all drivers with ndo_get_stats64 to have a void function. Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-18netns: make struct pernet_operations::id unsigned intAlexey Dobriyan1-1/+1
Make struct pernet_operations::id unsigned. There are 2 reasons to do so: 1) This field is really an index into an zero based array and thus is unsigned entity. Using negative value is out-of-bound access by definition. 2) On x86_64 unsigned 32-bit data which are mixed with pointers via array indexing or offsets added or subtracted to pointers are preffered to signed 32-bit data. "int" being used as an array index needs to be sign-extended to 64-bit before being used. void f(long *p, int i) { g(p[i]); } roughly translates to movsx rsi, esi mov rdi, [rsi+...] call g MOVSX is 3 byte instruction which isn't necessary if the variable is unsigned because x86_64 is zero extending by default. Now, there is net_generic() function which, you guessed it right, uses "int" as an array index: static inline void *net_generic(const struct net *net, int id) { ... ptr = ng->ptr[id - 1]; ... } And this function is used a lot, so those sign extensions add up. Patch snipes ~1730 bytes on allyesconfig kernel (without all junk messing with code generation): add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730) Unfortunately some functions actually grow bigger. This is a semmingly random artefact of code generation with register allocator being used differently. gcc decides that some variable needs to live in new r8+ registers and every access now requires REX prefix. Or it is shifted into r12, so [r12+0] addressing mode has to be used which is longer than [r8] However, overall balance is in negative direction: add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730) function old new delta nfsd4_lock 3886 3959 +73 tipc_link_build_proto_msg 1096 1140 +44 mac80211_hwsim_new_radio 2776 2808 +32 tipc_mon_rcv 1032 1058 +26 svcauth_gss_legacy_init 1413 1429 +16 tipc_bcbase_select_primary 379 392 +13 nfsd4_exchange_id 1247 1260 +13 nfsd4_setclientid_confirm 782 793 +11 ... put_client_renew_locked 494 480 -14 ip_set_sockfn_get 730 716 -14 geneve_sock_add 829 813 -16 nfsd4_sequence_done 721 703 -18 nlmclnt_lookup_host 708 686 -22 nfsd4_lockt 1085 1063 -22 nfs_get_client 1077 1050 -27 tcf_bpf_init 1106 1076 -30 nfsd4_encode_fattr 5997 5930 -67 Total: Before=154856051, After=154854321, chg -0.00% Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-30net: bonding: use new api ethtool_{get|set}_link_ksettingsPhilippe Reynes1-8/+8
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-18net: bonding: Flip to the new dev walk APIDavid Ahern1-8/+9
Convert alb_send_learning_packets and bond_has_this_ip to use the new netdev_walk_all_upper_dev_rcu API. In both cases this is just a code conversion; no functional change is intended. v2 - removed typecast of data and simplified bond_upper_dev_walk Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-11Merge branch 'work.uaccess2' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull uaccess.h prepwork from Al Viro: "Preparations to tree-wide switch to use of linux/uaccess.h (which, obviously, will allow to start unifying stuff for real). The last step there, ie PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>' sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \ `git grep -l "$PATT"|grep -v ^include/linux/uaccess.h` is not taken here - I would prefer to do it once just before or just after -rc1. However, everything should be ready for it" * 'work.uaccess2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: remove a stray reference to asm/uaccess.h in docs sparc64: separate extable_64.h, switch elf_64.h to it score: separate extable.h, switch module.h to it mips: separate extable.h, switch module.h to it x86: separate extable.h, switch sections.h to it remove stray include of asm/uaccess.h from cacheflush.h mn10300: remove a bogus processor.h->uaccess.h include xtensa: split uaccess.h into C and asm sides bonding: quit messing with IOCTL kill __kernel_ds_p off mn10300: finish verify_area() off frv: move HAVE_ARCH_UNMAPPED_AREA to pgtable.h exceptions: detritus removal
2016-09-27bonding: quit messing with IOCTLAl Viro1-2/+2
The only remaining users are issuing SIOCGMIIPHY and SIOCGMIIREG, neither of which deals with userland pointers. Simply calling ->ndo_do_ioctl() is fine; no messing with set_fs() is needed. It used to mess with SIOCETHTOOL, which would've needed set_fs(), but that has been killed in "[NET] ethtool ops are the only way" 9 years ago... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2016-09-12Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-3/+4
Conflicts: drivers/net/ethernet/mediatek/mtk_eth_soc.c drivers/net/ethernet/qlogic/qed/qed_dcbx.c drivers/net/phy/Kconfig All conflicts were cases of overlapping commits. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-04bonding: Fix bonding crashMahesh Bandewar1-3/+4
Following few steps will crash kernel - (a) Create bonding master > modprobe bonding miimon=50 (b) Create macvlan bridge on eth2 > ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \ type macvlan (c) Now try adding eth2 into the bond > echo +eth2 > /sys/class/net/bond0/bonding/slaves <crash> Bonding does lots of things before checking if the device enslaved is busy or not. In this case when the notifier call-chain sends notifications, the bond_netdev_event() assumes that the rx_handler /rx_handler_data is registered while the bond_enslave() hasn't progressed far enough to register rx_handler for the new slave. This patch adds a rx_handler check that can be performed right at the beginning of the enslave code to avoid getting into this situation. Signed-off-by: Mahesh Bandewar <maheshb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-01bonding: Remove deprecated create_singlethread_workqueueBhaktipriya Shridhar1-1/+1
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set, replaces deprecated create_singlethread_workqueue(). This is the identity conversion. The workqueue "wq" queues multiple work items viz &bond->mcast_work, &nnw->work, &bond->mii_work, &bond->arp_work, &bond->alb_work, &bond->mii_work, &bond->ad_work, &bond->slave_arr_work which require strict execution ordering. Hence, an ordered dedicated workqueue has been used. Since, it is a network driver, WQ_MEM_RECLAIM has been set to ensure forward progress under memory pressure. Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-09bonding: fix the typoZhu Yanjun1-1/+1
The message "803.ad" should be "802.3ad". Signed-off-by: Zhu Yanjun <zyjzyj2000@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-25net/bonding: Enforce active-backup policy for IPoIB bondsMark Bloch1-1/+10
When using an IPoIB bond currently only active-backup mode is a valid use case and this commit strengthens it. Since commit 2ab82852a270 ("net/bonding: Enable bonding to enslave netdevices not supporting set_mac_address()") was introduced till 4.7-rc1, IPoIB didn't support the set_mac_address ndo, and hence the fail over mac policy always applied to IPoIB bonds. With the introduction of commit 492a7e67ff83 ("IB/IPoIB: Allow setting the device address"), that doesn't hold and practically IPoIB bonds are broken as of that. To fix it, lets go to fail over mac if the device doesn't support the ndo OR this is IPoIB device. As a by-product, this commit also prevents a stack corruption which occurred when trying to copy 20 bytes (IPoIB) device address to a sockaddr struct that has only 16 bytes of storage. Signed-off-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-0/+1
Conflicts: drivers/net/ethernet/mellanox/mlx5/core/en.h drivers/net/ethernet/mellanox/mlx5/core/en_main.c drivers/net/usb/r8152.c All three conflicts were overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-05bonding: fix enslavement slave link notificationsAviv Heller1-0/+1
Currently, link notifications are not sent by bond_set_slave_link_state() upon enslavement if the slave is enslaved when up. This happens because slave->link default init value is 0, which is the same as BOND_LINK_UP, resulting in bond_set_slave_link_state() ignoring this transition. This patch sets the default value of slave->link to BOND_LINK_NOCHANGE, assuring it will count as a state transition and thus trigger notification logic. Signed-off-by: Aviv Heller <avivh@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-05net: introduce default neigh_construct/destroy ndo calls for L2 upper devicesJiri Pirko1-0/+2
L2 upper device needs to propagate neigh_construct/destroy calls down to lower devices. Do this by defining default ndo functions and use them in team, bond, bridge and vlan. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-09net: add netdev_lockdep_set_classes() helperEric Dumazet1-23/+1
It is time to add netdev_lockdep_set_classes() helper so that lockdep annotations per device type are easier to manage. This removes a lot of copies and missing annotations. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-07net_sched: transform qdisc running bit into a seqcountEric Dumazet1-0/+2
Instead of using a single bit (__QDISC___STATE_RUNNING) in sch->__state, use a seqcount. This adds lockdep support, but more importantly it will allow us to sample qdisc/class statistics without having to grab qdisc root lock. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-18bonding: fix bond_get_stats()Eric Dumazet1-31/+35
bond_get_stats() can be called from rtnetlink (with RTNL held) or from /proc/net/dev seq handler (with RCU held) The logic added in commit 5f0c5f73e5ef ("bonding: make global bonding stats more reliable") kind of assumed only one cpu could run there. If multiple threads are reading /proc/net/dev, stats can be really messed up after a while. A second problem is that some fields are 32bit, so we need to properly handle the wrap around problem. Given that RTNL is not always held, we need to use bond_for_each_slave_rcu(). Fixes: 5f0c5f73e5ef ("bonding: make global bonding stats more reliable") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-18bonding: remove duplicate set of flag IFF_MULTICASTZhang Shengju1-1/+1
Remove unnecessary set of flag IFF_MULTICAST, since ether_setup already does this. Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25net: bonding: use __ethtool_get_ksettingsDavid Decotigny1-8/+6
Signed-off-by: David Decotigny <decot@googlers.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-11/+29
Conflicts: drivers/net/phy/bcm7xxx.c drivers/net/phy/marvell.c drivers/net/vxlan.c All three conflicts were cases of simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-16bonding: don't use stale speed and duplex informationJay Vosburgh1-0/+1
There is presently a race condition between the bonding periodic link monitor and the updating of a slave's speed and duplex. The former occurs on a periodic basis, and the latter in response to a driver's calling of netif_carrier_on. It is possible for the periodic monitor to run between the driver call of netif_carrier_on and the receipt of the NETDEV_CHANGE event that causes bonding to update the slave's speed and duplex. This manifests most notably as a report that a slave is up and "0 Mbps full duplex" after enslavement, but in principle could report an incorrect speed and duplex after any link up event if the device comes up with a different speed or duplex. This affects the 802.3ad aggregator selection, as the speed and duplex are selection criteria. This is fixed by updating the speed and duplex in the periodic monitor, prior to using that information. This was done historically in bonding, but the call to bond_update_speed_duplex was removed in commit 876254ae2758 ("bonding: don't call update_speed_duplex() under spinlocks"), as it might sleep under lock. Later, the locking was changed to only hold RTNL, and so after commit 876254ae2758 ("bonding: don't call update_speed_duplex() under spinlocks") this call is again safe. Tested-by: "Tantilov, Emil S" <emil.s.tantilov@intel.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: dingtianhong <dingtianhong@huawei.com> Fixes: 876254ae2758 ("bonding: don't call update_speed_duplex() under spinlocks") Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Acked-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-13bonding: Fix ARP monitor validationJay Vosburgh1-11/+28
The current logic in bond_arp_rcv will accept an incoming ARP for validation if (a) the receiving slave is either "active" (which includes the currently active slave, or the current ARP slave) or, (b) there is a currently active slave, and it has received an ARP since it became active. For case (b), the receiving slave isn't the currently active slave, and is receiving the original broadcast ARP request, not an ARP reply from the target. This logic can fail if there is no currently active slave. In this situation, the ARP probe logic cycles through all slaves, assigning each in turn as the "current_arp_slave" for one arp_interval, then setting that one as "active," and sending an ARP probe from that slave. The current logic expects the ARP reply to arrive on the sending current_arp_slave, however, due to switch FDB updating delays, the reply may be directed to another slave. This can arise if the bonding slaves and switch are working, but the ARP target is not responding. When the ARP target recovers, a condition may result wherein the ARP target host replies faster than the switch can update its forwarding table, causing each ARP reply to be sent to the previous current_arp_slave. This will never pass the logic in bond_arp_rcv, as neither of the above conditions (a) or (b) are met. Some experimentation on a LAN shows ARP reply round trips in the 200 usec range, but my available switches never update their FDB in less than 4000 usec. This patch changes the logic in bond_arp_rcv to additionally accept an ARP reply for validation on any slave if there is a current ARP slave and it sent an ARP probe during the previous arp_interval. Fixes: aeea64ac717a ("bonding: don't trust arp requests unless active slave really works") Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-11bonding: use return instead of gotoZhang Shengju1-6/+3
Replace 'goto' with 'return' to remove unnecessary check at label: err_undo_flags. The reason is that 'err_undo_flags' do two things for the first slave device: 1.revert bond mac address if it is set by the slave device. 2.revert bond device type if it's not ARPHRD_ETHER. It's not necessary for the following three places, they changed neither bond mac address nor type. It's straightforward to return directly. Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-08bonding: trivial: style fixesZhang Shengju1-6/+4
remove some redudant brackets, use sizeof(*) instead of sizeof(struct x). Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-06bonding: add slave device name for debugZhang Shengju1-2/+2
netdev_dbg() will add bond device name, it will be helpful if we print slave device name. Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-06bond: track sum of rx_nohandler for all slavesJarod Wilson1-0/+1
Sample output with this set applied for an active-backup bond: $ cat /sys/devices/virtual/net/bond0/lower_p7p1/statistics/rx_nohandler 16568 $ cat /sys/devices/virtual/net/bond0/lower_p5p2/statistics/rx_nohandler 16583 $ cat /sys/devices/virtual/net/bond0/statistics/rx_nohandler 33151 CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <gospo@cumulusnetworks.com> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-1/+4
Conflicts: drivers/net/bonding/bond_main.c drivers/net/ethernet/mellanox/mlxsw/spectrum.h drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c The bond_main.c and mellanox switch conflicts were cases of overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-11bonding: Prevent IPv6 link local address on enslaved devicesKarl Heiss1-1/+4
Commit 1f718f0f4f97 ("bonding: populate neighbour's private on enslave") undoes the fix provided by commit c2edacf80e15 ("bonding / ipv6: no addrconf for slaves separately from master") by effectively setting the slave flag after the slave has been opened. If the slave comes up quickly enough, it will go through the IPv6 addrconf before the slave flag has been set and will get a link local IPv6 address. In order to ensure that addrconf knows to ignore the slave devices on state change, set IFF_SLAVE before dev_open() during bonding enslavement. Fixes: 1f718f0f4f97 ("bonding: populate neighbour's private on enslave") Signed-off-by: Karl Heiss <kheiss@gmail.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Reviewed-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15net: Rename NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASKTom Herbert1-4/+3
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the set of features for offloading all checksums. This is a mask of the checksum offload related features bits. It is incorrect to set both NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for features of a device. This patch: - Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where NETIF_F_ALL_CSUM is being used as a mask). - Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM. Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-04net: bonding: remove redudant bracketsyzhu11-1/+1
It is not necessary to use two brackets. As such, the redudant brackets are removed. CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: Zhu Yanjun <yanjun.zhu@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-03bonding: set inactive flags on releaseJiri Pirko1-0/+2
Be correct and symmetric to enslave and set inactive flags during release. That gives LAG offload drivers - lower state change listeners - possibility to do proper cleanup. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-03bonding: implement lower state change propagationJiri Pirko1-0/+10
Let netdev notifier listeners know about link and slave state change. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-03bonding: allow notifications for bond_set_slave_link_stateJiri Pirko1-18/+36
Similar to state notifications. We allow caller to indicate if the notification should happen now or later, depending on if he holds rtnl mutex or not. Introduce bond_slave_link_notify function (similar to bond_slave_state_notify) which is later on called with rtnl mutex and goes over slaves and executes delayed notification. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-03bonding: fill-up LAG changeupper info struct and pass it alongJiri Pirko1-14/+31
Initialize netdev_lag_upper_info structure by TX type according to current bonding mode and pass it along via netdev_master_upper_dev_link. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-03net: add possibility to pass information about upper device via notifierJiri Pirko1-1/+1
Sometimes the drivers and other code would find it handy to know some internal information about upper device being changed. So allow upper-code to pass information down to notifier listeners during linking. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-03net: propagate upper priv via netdev_master_upper_dev_linkJiri Pirko1-1/+1
Eliminate netdev_master_upper_dev_link_private and pass priv directly as a parameter of netdev_master_upper_dev_link. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-07bonding: fix panic on non-ARPHRD_ETHER enslave failureJay Vosburgh1-0/+1
Since commit 7d5cd2ce529b, when bond_enslave fails on devices that are not ARPHRD_ETHER, if needed, it resets the bonding device back to ARPHRD_ETHER by calling ether_setup. Unfortunately, ether_setup clobbers dev->flags, clearing IFF_UP if the bond device is up, leaving it in a quasi-down state without having actually gone through dev_close. For bonding, if any periodic work queue items are active (miimon, arp_interval, etc), those will remain running, as they are stopped by bond_close. At this point, if the bonding module is unloaded or the bond is deleted, the system will panic when the work function is called. This panic is resolved by calling dev_close on the bond itself prior to calling ether_setup. Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Fixes: 7d5cd2ce5292 ("bonding: correctly handle bonding type change on enslave failure") Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-28 06:18:47 +0000