summaryrefslogtreecommitdiffstats
path: root/drivers/net/bnx2x
AgeCommit message (Collapse)AuthorFilesLines
2010-11-28bnx2x: Use helpers instead of direct access to the shinfo(skb) fieldsVladislav Zolotarov1-5/+4
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-24bnx2x: Do interrupt mode initialization and NAPIs adding before ↵Vladislav Zolotarov2-8/+8
register_netdev() Move the interrupt mode configuration and NAPIs adding before a register_netdev() call to prevent netdev->open() from running before these functions are done. Advance a driver version number. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Reported-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-24bnx2x: Disable local BHes to prevent a dead-lock situationEric Dumazet1-1/+8
According to Eric's suggestion: Disable local BHes to prevent a dead-lock situation between sch_direct_xmit() (Soft_IRQ context) and bnx2x_tx_int (called by bnx2x_run_loopback() - syscall context), as both are taking a netif_tx_lock(). Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19Merge branch 'master' of ↵David S. Miller1-1/+1
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/bonding/bond_main.c net/core/net-sysfs.c net/ipv6/addrconf.c
2010-11-17net: bnx2x: fix error value signVasiliy Kulikov1-1/+1
bnx2x_init_one() should return negative value on error. By mistake it returns ENODEV instead of -ENODEV. Signed-off-by: Vasiliy Kulikov <segoon@openwall.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-15drivers/net/bnx2x: Remove unnecessary semicolonsJoe Perches2-3/+3
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-12bnx2x: Look inside vlan when determining checksum proto.Hao Zheng1-1/+1
Currently the skb->protocol field is used to setup checksum offloading on transmit for the correct protocol. However, if vlan offloading is disabled or otherwise not used, the protocol field will be ETH_P_8021Q, not the actual protocol. This will cause the checksum to be not computed correctly, even though the hardware is capable of looking inside vlan tags. Instead, look inside the header if necessary to determine the correct protocol type. To some extent this fixes a regression from 2.6.36 because it was previously not possible to disable vlan offloading and this error case was not exposed. Signed-off-by: Hao Zheng <hzheng@nicira.com> CC: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-01bnx2x: Update version numberYaniv Rosner1-2/+2
Update bnx2x version number. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-01bnx2x: Reset 8073 phy during common initYaniv Rosner1-0/+1
Resetting 8073 during common init is required on boards in which the 8073 reset pin is not asserted by default. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-01bnx2x: Do not enable CL37 BAM unless it is explicitly enabledYaniv Rosner2-7/+20
Enabling CL37 BAM on BCM8073 by default may lead to link issues since not all switches support it. So enable CL37 BAM only if explicitly selected. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-01bnx2x: Fix resetting BCM8726 PHY during common initYaniv Rosner1-1/+1
On BCM8726 based designs, the ports are swapped, hence the reset needs to be asserted through port0 and not port1. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-01bnx2x: Clear latch indication on link resetYaniv Rosner1-1/+10
When using latch indication for link change notification, need to clear it when port is unloaded, otherwise it might generate false indication on next load. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-01bnx2x: Fix port selection in case of E2Yaniv Rosner1-3/+12
On E2 flavor, dual-port mode, the port argument used for some functions is needed as the global port number rather than the port per path. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-01bnx2x: Fix waiting for reset complete on BCM848x3 PHYsYaniv Rosner1-3/+5
BCM848x3 requires additional of 50ms after reset done indication, instead of fixed time of 200ms Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-01bnx2x: Restore appropriate delay during BMAC resetYaniv Rosner1-1/+1
Fix delay during BMAC reset from 10usec to 1ms. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-24bnx2x: make local function static and remove dead codestephen hemminger7-242/+62
Make many functions that are only used in one file static. Remove dead code for override_led_value. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.Jesse Gross1-1/+1
Some cards don't support changing vlan offloading settings. Make Ethtool set_flags return -EINVAL in those cases. Reported-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21bnx2x: Update bnx2x to use new vlan accleration.Hao Zheng4-84/+27
Make the bnx2x driver use the new vlan accleration model. Signed-off-by: Hao Zheng <hzheng@nicira.com> Signed-off-by: Jesse Gross <jesse@nicira.com> CC: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21vlan: Don't check for vlan group before vlan_tx_tag_present.Jesse Gross1-2/+1
Many (but not all) drivers check to see whether there is a vlan group configured before using a tag stored in the skb. There's not much point in this check since it just throws away data that should only be present in the expected circumstances. However, it will soon be legal and expected to get a vlan tag when no vlan group is configured, so remove this check from all drivers to avoid dropping the tags. Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-19bnx2x: update version to 1.60.00-3Dmitry Kravkov1-2/+2
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-19bnx2x: prevent false parity error in MSI-X memory of HC blockVladislav Zolotarov2-2/+32
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-19bnx2x: fix possible deadlock in HC hw blockDmitry Kravkov1-8/+29
The possible deadlock (on 57710 devices only) will prevent from the device to generate interrupts. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18bnx2x: update version to 1.60.00-2Dmitry Kravkov1-2/+2
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18bnx2x: remove unnecessary FUNC_FLG_RSS flag and relatedDmitry Kravkov2-49/+34
As suggested by: Joe Perches <joe@perches.com> Although RSS is meaningless when there is a single HW queue we still need it enabled in order to have HW Rx hash generated. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18bnx2x: Use correct FW constant for header paddingDmitry Kravkov2-3/+1
the value of the constant is the same, but it's clearer to use original constant provided by HSI Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18bnx2x: do not deal with power if no capabilityDmitry Kravkov1-0/+6
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18bnx2x: remove redundant commands during error handlingDmitry Kravkov1-2/+0
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18bnx2x: Optimized the branching in the bnx2x_rx_int()Vladislav Zolotarov1-5/+6
Optimized the branching in the bnx2x_rx_int() based on the fact that FP CQE will always have at least one of START or STOP flags set, so if not both bits are set and START bit is not set, then it's a STOP bit that is set. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-12bnx2x: Fixing a typo: added a missing RSS enablementDmitry Kravkov1-0/+1
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: update version to 1.60.00-1Dmitry Kravkov1-2/+2
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: properly initialize FW statsDmitry Kravkov1-0/+13
Client statistics need to be initialized to -1 Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: code beautifyDmitry Kravkov7-233/+318
This patch does not include any functional changes. The changes are: empty lines, indentation and comments. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x, cnic: Fix SPQ return creditDmitry Kravkov2-30/+69
Return proper L2 and L5 SPQ (slow path queue) credits. Previously, all SPQ events were counted as L5 types. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: move msix table initialization to probe()Dmitry Kravkov4-134/+228
Decide which interrupt mode to use (MSI-X, MSI, INTa) only once in probe() and initialize appropriate structures. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: use L1_CACHE_BYTES instead of magic numberDmitry Kravkov1-2/+2
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: use proper constants for dma_unmap* callsDmitry Kravkov2-2/+2
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: remove unused fields in main driver structureDmitry Kravkov1-7/+0
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: remove unused parameter in reuse_rx_skb()Dmitry Kravkov2-3/+3
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: Add 57712 supportDmitry Kravkov13-789/+3426
57712 HW supported with same set of features as for 57710/57711 Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: change type of spq_left to atomicDmitry Kravkov3-13/+11
The field is now accessed from different contexts. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: rename MF related fieldsDmitry Kravkov5-47/+47
MF (multi-function) mode supported not only by 57711E (E1H) devices, but also by coming 57712E, then we use more generic names. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x, cnic, bnx2i: use new FW/HSIDmitry Kravkov12-2822/+4361
This is the new FW HSI blob and the relevant definitions without logic changes. It also included code adaptation for new HSI. New features are not enabled. New FW/HSI includes: - Support for 57712 HW - Future support for VF (not used) - Improvements in FW interrupts scheme - FW FCoE hooks (stubs for future usage) Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06bnx2x: create folder for bnx2x firmware filesDmitry Kravkov1-2/+2
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-29bnx2x: Moved enabling of MSI to the bnx2x_set_num_queues()Dmitry Kravkov1-6/+11
Moved enabling of MSI to the bnx2x_set_num_queues() - the same functions that handles the initialization of the MSI-X. From: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-27bnx2x: Use netif_set_real_num_{rx,tx}_queues()Ben Hutchings1-2/+4
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-26drivers/net: return operator cleanupEric Dumazet1-2/+2
Change "return (EXPR);" to "return EXPR;" return is not a function, parentheses are not required. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-13bnx2x: Spread rx buffers between allocated queuesDmitry Kravkov4-5/+17
Default number of rx buffers will be divided equally between allocated queues. This will decrease amount of pre-allocated buffers on systems with multiple CPUs. User can override this behavior with ethtool -G. Minimum amount of rx buffers per queue set to 128. Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-09drivers/net/bnx2x: use ARRAY_SIZE macro in bnx2x_main.cNikitas Angelinas1-3/+2
Replace sizeof(bnx2x_parity_mask)/(sizeof(bnx2x_parity_mask[0]) with ARRAY_SIZE(bnx2x_parity_mask) in drivers/net/bnx2x/bnx2x_main.c Signed-off-by: Nikitas Angelinas <nikitasangelinas@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-07bnx2x: Update bnx2x version to 1.52.53-6Yaniv Rosner1-2/+2
Note that the date format was fixed. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-07bnx2x: Change LED scheme for dual-mediaYaniv Rosner5-46/+336
Change LED scheme for dual-media Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-03 12:59:39 +0000