| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Version 4 of the ONFI spec mandates that tADL be at least 400 nanoseconds,
but, depending on the master clock rate, 400 ns may not fit in the tADL
field of the SMC reg. We need to relax the check and accept the -ERANGE
return code.
Note that previous versions of the ONFI spec had a lower tADL_min (100 or
200 ns). It's not clear why this timing constraint got increased but it
seems most NANDs are fine with values lower than 400ns, so we should be
safe.
Fixes: f9ce2eddf176 ("mtd: nand: atmel: Add ->setup_data_interface() hooks")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The debugfs entries must be removed before an error is returned in the
probe function. Otherwise another try to load the module fails and when
the debugfs files are accessed without the module loaded, the kernel
still tries to call a function in that module.
Fixes: 5346c27c5fed ("mtd: nandsim: Introduce debugfs infrastructure")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
All the MTD block write requests are failing with
following error messages
mkfs.ext4 /dev/mtdblock0
print_req_error: I/O error, dev mtdblock0, sector 0
Buffer I/O error on dev mtdblock0, logical block 0,
lost async page write
The control is going to default case after block write request
because of missing return.
Fixes: commit 2a842acab109 ("block: introduce new block status code type")
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
EDO mode should be used when tRC is less than 30ns, but timings are
expressed in picoseconds in the nand_sdr_timings struct.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: f9ce2eddf176 ("mtd: nand: atmel: Add ->setup_data_interface() hooks")
Reported-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
All timings in nand_sdr_timings are expressed in picoseconds but some
of them may not fit in an u32.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 204e7ecd47e2 ("mtd: nand: Add a few more timings to nand_sdr_timings")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some ONFI NANDs do not support the SET/GET FEATURES commands, which,
according to the spec, is perfectly valid.
On these NANDs we can't set a specific timing mode using the "timing
mode" feature, and we should assume the NAND does not require any setup
to enter a specific timing mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd8311 ("mtd: nand: automate NAND timings selection")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Commit 0b4773fd1649 (mtd: nand: Drop unused cached programming support)
removed the "cached" parameter from nand_write_page(), but did not update
the kerneldoc comments, creating this docs build warning:
./drivers/mtd/nand/nand_base.c:2751: warning: Excess function parameter 'cached' description in 'nand_write_page'
Remove the offending line so we can have a little peace and quiet.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
clk_round_rate() can return <= 0. Currently the value returned by
clk_round_rate() is used directly for a division. This patch introduces a
guard to ensure a divide-by-zero or a divide by a negative number for that
matter can't happen by bugging out returning -EINVAL if clk_round_rate()
returns <= 0.
Fixes: 2d43457f79e4 ("mtd: nand: sunxi: fix EDO mode selection")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
When using soft ecc, if no ooblayout is given, the core automatically
uses one of the nand_ooblayout_{sp,lp}*() functions to determine the
layout inside the out of band data.
Until kernel version 4.6, struct nand_ecclayout was used for that
purpose. During the migration from 4.6 to 4.7, an error shown up in the
small page layout, in the case oob section is only 8 bytes long.
The layout was using three bytes (0, 1, 2) for ecc, two bytes (3, 4)
as free bytes, one byte (5) for bad block marker and finally
two bytes (6, 7) as free bytes, as shown there:
[linux-4.6] drivers/mtd/nand/nand_base.c:52
static struct nand_ecclayout nand_oob_8 = {
.eccbytes = 3,
.eccpos = {0, 1, 2},
.oobfree = {
{.offset = 3,
.length = 2},
{.offset = 6,
.length = 2} }
};
This fixes the current implementation which is incoherent. It
references bit 3 at the same time as an ecc byte and a free byte.
Furthermore, it is clear with the previous implementation that there
is only one ecc section with 8 bytes oob sections. We shall return
-ERANGE in the nand_ooblayout_ecc_sp() function when asked for the
second section.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Fixes: 41b207a70d3a ("mtd: nand: implement the default mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
PMECC caps extraction from old DT bindings is broken, thus leading to
erroneous EL registers offset, which in turn make HW ECC unusable on
sama5d2 when old bindings are in use.
Passing the NAND dev node instead of the NFC node to of_match_node()
solves the problem.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Tested-by: Romain Izard <romain.izard.pro@gmail.com>
|
|
Pull MTD updates from Brian Norris:
"General updates:
- Cleanups and additional flash support for "dataflash" driver
- new driver for mchp23k256 SPI SRAM device
- improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
- refactor and improve "sub-partition" handling with TRX partition
parser; partitions can now be created as sub-partitions of another
partition
SPINOR updates, from Cyrille Pitchen and Marek Vasut:
- introduce support to the SPI 1-2-2 and 1-4-4 protocols.
- introduce support to the Double Data Rate (DDR) mode.
- introduce support to the Octo SPI protocols.
- add support to new memory parts for Spansion, Macronix and Winbond.
- add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
- clean up the st_spi_fsm driver.
NAND updates, from Boris Brezillon:
- addition of on-die ECC support to Micron driver
- addition of helpers to help drivers choose most appropriate ECC
settings
- deletion of dead-code (cached programming and ->errstat() hook)
- make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
- change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
- support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
- change the prototype of ->setup_data_interface()
A bunch of driver related changes:
- various cleanup, fixes and improvements of the MTK driver
- OMAP DT bindings fixes
- support for ->setup_data_interface() in the fsmc driver
- support for imx7 in the gpmi driver
- finalization of the denali driver rework (thanks to Masahiro for
the work he's done on this driver)
- fix "bitflips in erased pages" handling in the ifc driver
- addition of PM ops and dynamic timing configuration to the atmel
driver"
* tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd: (118 commits)
Documentation: ABI: mtd: describe "offset" more precisely
mtd: Fix check in mtd_unpoint()
mtd: nand: mtk: release lock on error path
mtd: st_spi_fsm: remove SPINOR_OP_RDSR2 and use SPINOR_OP_RDCR instead
mtd: spi-nor: cqspi: remove duplicate const
mtd: spi-nor: Add support for Spansion S25FL064L
mtd: spi-nor: Add support for mx66u51235f
mtd: nand: mtk: add ->setup_data_interface() hook
mtd: nand: mtk: remove unneeded mtk_ecc_hw_init from mtk_ecc_resume
mtd: nand: mtk: remove unneeded mtk_nfc_hw_init from mtk_nfc_resume
mtd: nand: mtk: disable ecc irq when writing page with hwecc
mtd: nand: mtk: fix incorrect register setting order about ecc irq
mtd: partitions: fixup some allocate_partition() whitespace
mtd: parsers: trx: fix pr_err format for printing offset
MAINTAINERS: Update SPI NOR subsystem git repositories
mtd: extract TRX parser out of bcm47xxpart into a separated module
mtd: partitions: add support for partition parsers
mtd: partitions: add support for subpartitions
mtd: partitions: rename "master" to the "parent" where appropriate
mtd: partitions: remove sysfs files when deleting all master's partitions
...
|
|
From Boris:
"""
This pull request contains the following core changes:
* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
"""
|
|
From Cyrille:
"""
This pull request contains the following notable changes:
- introduce support to the SPI 1-2-2 and 1-4-4 protocols.
- introduce support to the Double Data Rate (DDR) mode.
- introduce support to the Octo SPI protocols.
- add support to new memory parts for Spansion, Macronix and Winbond.
- add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
- clean up the st_spi_fsm driver.
"""
|
|
The code checks that ->_point is not NULL, but we should actually check
->_unpoint value which is dereferenced a few lines after the check.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
|
|
Pull documentation updates from Jonathan Corbet:
"There has been a fair amount of activity in the docs tree this time
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates"
* tag 'docs-4.13' of git://git.lwn.net/linux: (90 commits)
scripts/kernel-doc: handle DECLARE_HASHTABLE
Documentation: atomic_ops.txt is core-api/atomic_ops.rst
Docs: clean up some DocBook loose ends
Make the main documentation title less Geocities
Docs: Use kernel-figure in vidioc-g-selection.rst
Docs: fix table problems in ras.rst
Docs: Fix breakage with Sphinx 1.5 and upper
Docs: Include the Latex "ifthen" package
doc/kokr/howto: Only send regression fixes after -rc1
docs-rst: fix broken links to dynamic-debug-howto in kernel-parameters
doc: Document suitability of IBM Verse for kernel development
Doc: fix a markup error in coding-style.rst
docs: driver-api: i2c: remove some outdated information
Documentation: DMA API: fix a typo in a function name
Docs: Insert missing space to separate link from text
doc/ko_KR/memory-barriers: Update control-dependencies example
Documentation, kbuild: fix typo "minimun" -> "minimum"
docs: Fix some formatting issues in request-key.rst
doc: ReSTify keys-trusted-encrypted.txt
doc: ReSTify keys-request-key.txt
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
|
|
We only want to hold the lock on the success path, not this error path.
Fixes: 7ec4a37c5d71 ("mtd: nand: mediatek: add support for different MTK NAND FLASH Controller IP")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Linux 4.12-rc7
|
|
The 35h instruction op code has two aliases/macro definitions:
- SPINOR_OP_RDCR from include/linux/mtd/spi-nor.h
- SPINOR_OP_RDSR2 from drivers/mtd/devices/serial_flash_cmds.h
Actually, some manufacturers name the associated internal register Status
Register 2 whereas other manufacturers name it Configuration Register
hence the two different macros for the very same instruction op code.
Since the spi-nor.h file is the reference file for all SPI NOR instruction
op codes, this patch removes the definition of the SPINOR_OP_RDSR2 macro.
Also the SPINOR_OP_RDSR2 macro will be associated to another instruction
op code in a further patch so we need to avoid a conflict defining this
macro twice. Indeed the JESD216 rev B specification, defining the SFDP
tables, also refers to the 3Eh and 3Fh instruction op codes to write/read
the Status Register 2 on some SPI NOR flash memories, the 35h op code
still being used to read the Configuration Register/Status Register 2 on
other memories.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
|
|
The variable was already marked 'const' before the previous
patch, but the qualifier was in an unusual place, and now the
extra 'const' causes a harmless warning:
drivers/mtd/spi-nor/cadence-quadspi.c:1286:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
This removes the other 'const' instead.
Fixes: f993c123b461 ("mtd: spi-nor: cqspi: make of_device_ids const")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
|
|
Instead move it to the callers. Those that either don't use bio_data() or
page_address() or are specific to architectures that do not support highmem
are skipped.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It's an 8 MiB flash with 4 KiB erase sectors.
Signed-off-by: Harry Chou <HarryYC.Chou@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
|
|
This chip supports stateless 4-byte opcodes, dual and quad read and
uniform 4K-byte erase.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
|
|
Currently, we use the fixed ACC timing 0x10804211. This is not the best
setting for each case. Actually, MTK NAND controller can adapt ACC timings
dynamically according to nfi clock frequence.
Implement the ->setup_data_interface() hook to optimize driver performance.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
There is no need to add mtk_ecc_hw_init during ecc resume, because there
always takes mtk_ecc_wait_idle in the function mtk_ecc_enable.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
chip->select_chip will do nfc runtime configuration. There is no need to
do mtk_nfc_hw_init before it.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Currently, ecc encode irq is enabled when writing page with hwecc, but
we actually do not wait for this irq done. Because NFI and ECC work in
parallel, nfi irq and ecc irq almost come together.
Now, there are two steps to check whether page data are totally written.
First, wait for nfi irq INTR_AHB_DONE. This is to ensure all data
in RAM are received by NFI.
Second, polling the register NFI_ADDRCNTR till all data include ecc
parity data runtime generated by ECC are sent to NAND device.
So, it is redunant to enable ecc irq without waiting for it.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Currently, we trigger ECC HW before setting ecc irq. It is incorrect.
Because ECC starts working once the register ECC_CTL_REG is set as
ECC_OP_ENABLE. And this may lead an abnormal behavior of ecc irq.
So, should enable ecc irq at first, then trigger ECC.
Fixes: 1d6b1e464950 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some recent patches caused churn around this area, and checkpatch
noticed the existing issues.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
This fixes following warning:
include/linux/kern_levels.h:4:18: warning: format '%X' expects argument of type 'unsigned int', but argument 2 has type 'size_t {aka long unsigned int}' [-Wformat=]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
This makes TRX parsing code reusable with other platforms and parsers.
Please note this patch doesn't really change anything in the existing
code, just moves it. There is still some place for improvement (e.g.
working on non-hacky method of checking rootfs format) but it's not
really a subject of this change.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Some devices have partitions that are kind of containers with extra
subpartitions / volumes instead of e.g. a simple filesystem data. To
support such cases we need to first create normal flash device
partitions and then take care of these special ones.
It's very common case for home routers. Depending on the vendor there
are formats like TRX, Seama, TP-Link, WRGG & more. All of them are used
to embed few partitions into a single one / single firmware file.
Ideally all vendors would use some well documented / standardized format
like UBI (and some probably start doing so), but there are still
countless devices on the market using these poor vendor specific
formats.
This patch extends MTD subsystem by allowing to specify list of parsers
that should be tried for a given partition. Supporting such poor formats
is highly unlikely to be the top priority so these changes try to
minimize maintenance cost to the minimum. It reuses existing code for
these new parsers and just adds a one property and one new function.
This implementation requires setting partition parsers in a flash
parser. A proper change of bcm47xxpart will follow and in the future we
will hopefully also find a solution for doing it with ofpart
("fixed-partitions").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Some flash device partitions can be containers with extra subpartitions
(volumes). All callbacks are already capable of this additional level of
indirection.
This patch makes sure we always display subpartitions using a tree
structure and takes care of deleting subpartitions when parent gets
removed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
This prepares mtd subsystem for the new feature: subpartitions. In some
cases flash device partition can be a container with extra subpartitions
(volumes).
So far there was a flat structure implemented. One master (flash device)
could be partitioned into few partitions. Every partition got its master
and it was enough to get things running.
To support subpartitions we need to store pointer to the parent for each
partition. This is required to implement more natural tree structure and
handle all recursion and offsets calculation.
To make code consistent this patch renamed "master" to the "parent" in
places where we can be dealing with subpartitions.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
When support for sysfs "offset" file was added it missed to update the
del_mtd_partitions function. It deletes partitions just like
mtd_del_partition does so both should also take care of removing sysfs
files.
This change moves sysfs_remove_files call to the shared function to fix
this issue.
Fixes: a62c24d755291 ("mtd: part: Add sysfs variable for offset of partition")
Cc: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
There are two similar functions handling deletion. One handles single
partition and another the whole MTD flash device. They share (duplicate)
some code so it makes sense to add a small helper for that part.
Function del_mtd_partitions has been moved a bit to keep all deleting
stuff together.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The segment registers of the SMC controller provide a way to configure
the mapping windows of the chips on the AHB bus. The settings are
required to be correct when the controller operates in Command mode,
which is the case for DMAs and the LPC mapping.
This tries to set the segment registers of each chip depending on the
size of the flash device and depending on the previous segment
settings, in order to have a contiguous window across multiple chips.
Unfortunately, the AST2500 SPI controller has a bug and it is not
possible to configure a full 128MB window for a chip of the same
size. The window size needs to be restricted to 120MB. This issue only
applies to CE0.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
|
|
There is no need to keep the dummy bytes in the control register if
the command mode is not kept also. This could lead to an inconsistent
setting : normal read mode (command 0x3) and dummy bytes. It is to be
noted that the HW allows such a configuration.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
|
|
These devices are used on OpenPOWER systems. The SPI_NOR_DUAL_READ
flags is added for the Aspeed SoCs which do not support QUAD reads.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
|
|
These modules are used on the OpenPOWER Witherspoon systems to hold
the POWER9 host firmware image. The SPI_NOR_DUAL_READ flags is added
for the Aspeed SoCs which do not support QUAD reads.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
|
|
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
|
|
Similar to the other ones, different size. The "JV" suffix is in
the datasheet, I haven't seen mentions of a different one.
The datasheet indicates DUAL and QUAD are supported.
http://www.winbond.com/resource-files/w25m512jv%20revc%2001062017.pdf
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
|
|
This code is going to be reused for parsers matched using OF so let's
factor it out to make this easier.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Brian Norris <computersforpeace@gmail.com>
|
|
All IFC version >= 1.0 use 28nm technology for SRAM. Here SRAM has
a requirement to initialize before any read operation performed for
avoiding ECC Error.
So update condition check to initialize SRAM for all IFC version >= 1.0.0
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Introduce some macros and helpers to avoid magic numbers and
rename macros/functions for clarification.
- We see '| 2' in several places. This means Data Cycle in MAP11 mode.
The Denali User's Guide says bit[1:0] of MAP11 is like follows:
b'00 = Command Cycle
b'01 = Address Cycle
b'10 = Data Cycle
So, this commit added DENALI_MAP11_{CMD,ADDR,DATA} macros.
- We see 'denali->flash_mem + 0x10' in several places, but 0x10 is a
magic number. Actually, this accesses the data port of the Host
Data/Command Interface. So, this commit added DENALI_HOST_DATA.
On the other hand, 'denali->flash_mem' gets access to the address
port, so DENALI_HOST_ADDR was also added.
- We see 'index_addr(denali, cmd, 0x1)' in denali_erase(), but 0x1
is a magic number. 0x1 means the erase operation. Replace 0x1
with DENALI_ERASE.
- Rename index_addr() to denali_host_write() for clarification
- Denali User's Guide says MAP{00,01,10,11} for access mode. Match
the macros with terminology in the IP document.
- Rename struct members as follows:
flash_bank -> active_bank (currently selected bank)
flash_reg -> reg (base address of registers)
flash_mem -> host (base address of host interface)
devnum -> devs_per_cs (devices connected in parallel)
bbtskipbytes -> oob_skip_bytes (number of bytes to skip in OOB)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Now this driver is ready to remove NAND_SKIP_BBTSCAN.
The BBT descriptors in denali.c are equivalent to the ones in
nand_bbt.c. There is no need to duplicate the equivalent structures.
The with-oob decriptors do not work for this driver anyway.
The bbt_pattern (offs = 8) and the version (veroffs = 12) area
overlaps the ECC area. Set NAND_BBT_NO_OOB flag to use the no_oob
variant of the BBT descriptors.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
As Russell and Lars stated in the discussion [1], using
devm_k*alloc() with DMA is not a good idea.
Let's use kmalloc (not kzalloc because no need for zero-out).
Also, allocate the buffer as late as possible because it must be
freed for any error that follows.
[1] https://lkml.org/lkml/2017/3/8/693
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
For ecc->read_page() and ecc->write_page(), it is possible to call
dma_map_single() against the given buffer. This bypasses the driver
internal bounce buffer and save the memcpy().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Recent versions of this IP support automatic erased page detection.
If an erased page is detected on reads, the controller does not set
INTR__ECC_UNCOR_ERR, but INTR__ERASED_PAGE.
The detection of erased pages is based on the number of zeros in a
page; if the number of zeros is less than the value in the field
ERASED_THRESHOLD, the page is assumed as erased.
Please note ERASED_THRESHOLD specifies the number of zeros in a _page_
instead of an ECC chunk. Moreover, the controller does not provide a
way to know the actual number of bitflips.
Actually, an erased page (all 0xff) is not an ECC correctable pattern
on the Denali ECC engine. In other words, there may be overlap between
the following two:
[1] a bit pattern reachable from a valid payload + ECC pattern within
ecc.strength bitflips
[2] a bit pattern reachable from an erased state (all 0xff) within
ecc.strength bitflips
So, this feature may intercept ECC correctable patterns, then replace
[1] with [2].
After all, this feature can work safely only when ECC_THRESHOLD == 1,
i.e. detect erased pages without any bitflips. This should be the
case most of the time. If there is a bitflip or more, the driver will
fallback to the software method by using nand_check_erased_ecc_chunk().
Strangely enough, the driver still has to fill the buffer with 0xff
in case of INTR__ERASED_PAGE because the ECC correction engine has
already manipulated the data in the buffer before it judges erased
pages.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
