| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
|
|
Pull ARM updates from Russell King:
"Changes included in this pull request:
- revert pxa2xx-flash back to using ioremap_cached() and switch
memremap() to use arch_memremap_wb()
- remove pci=firmware command line argument handling
- remove unnecessary arm_dma_set_mask() implementation, the generic
implementation will do for ARM
- removal of the ARM kallsyms "hack" to work around mode switching
veneers and vectors located below PAGE_OFFSET
- tidy up build system output a little
- add L2 cache power management DT bindings
- remove duplicated local_irq_disable() in reboot paths
- handle AMBA primecell devices better at registration time with PM
domains (needed for Samsung SoCs)
- ARM specific preparation to support Keystone II kexec"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8567/1: cache-uniphier: activate ways for secondary CPUs
ARM: 8570/2: Documentation: devicetree: Add PL310 PM bindings
ARM: 8569/1: pl2x0: Add OF control of cache power management
ARM: 8568/1: reboot: remove duplicated local_irq_disable()
ARM: 8566/1: drivers: amba: properly handle devices with power domains
ARM: provide arm_has_idmap_alias() helper
ARM: kexec: remove 512MB restriction on kexec crashdump
ARM: provide improved virt_to_idmap() functionality
ARM: kexec: fix crashkernel= handling
ARM: 8557/1: specify install, zinstall, and uinstall as PHONY targets
ARM: 8562/1: suppress "include/generated/mach-types.h is up to date."
ARM: 8553/1: kallsyms: remove --page-offset command line option
ARM: 8552/1: kallsyms: remove special lower address limit for CONFIG_ARM
ARM: 8555/1: kallsyms: ignore ARM mode switching veneers
ARM: 8548/1: dma-mapping: remove arm_dma_set_mask()
ARM: 8554/1: kernel: pci: remove pci=firmware command line parameter handling
ARM: memremap: implement arch_memremap_wb()
memremap: add arch specific hook for MEMREMAP_WB mappings
mtd: pxa2xx-flash: switch back from memremap to ioremap_cached
ARM: reintroduce ioremap_cached() for creating cached I/O mappings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs cleanups from Al Viro:
"Assorted cleanups and fixes all over the place"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
coredump: only charge written data against RLIMIT_CORE
coredump: get rid of coredump_params->written
ecryptfs_lookup(): try either only encrypted or plaintext name
ecryptfs: avoid multiple aliases for directories
bpf: reject invalid names right in ->lookup()
__d_alloc(): treat NULL name as QSTR("/", 1)
mtd: switch ubi_open_volume_path() to vfs_stat()
mtd: switch open_mtd_by_chdev() to use of vfs_stat()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (21 commits)
gitignore: fix wording
mfd: ab8500-debugfs: fix "between" in printk
memstick: trivial fix of spelling mistake on management
cpupowerutils: bench: fix "average"
treewide: Fix typos in printk
IB/mlx4: printk fix
pinctrl: sirf/atlas7: fix printk spelling
serial: mctrl_gpio: Grammar s/lines GPIOs/line GPIOs/, /sets/set/
w1: comment spelling s/minmum/minimum/
Blackfin: comment spelling s/divsor/divisor/
metag: Fix misspellings in comments.
ia64: Fix misspellings in comments.
hexagon: Fix misspellings in comments.
tools/perf: Fix misspellings in comments.
cris: Fix misspellings in comments.
c6x: Fix misspellings in comments.
blackfin: Fix misspelling of 'register' in comment.
avr32: Fix misspelling of 'definitions' in comment.
treewide: Fix typos in printk
Doc: treewide : Fix typos in DocBook/filesystem.xml
...
|
|
Pull block driver updates from Jens Axboe:
"On top of the core pull request, this is the drivers pull request for
this merge window. This contains:
- Switch drivers to the new write back cache API, and kill off the
flush flags. From me.
- Kill the discard support for the STEC pci-e flash driver. It's
trivially broken, and apparently unmaintained, so it's safer to
just remove it. From Jeff Moyer.
- A set of lightnvm updates from the usual suspects (Matias/Javier,
and Simon), and fixes from Arnd, Jeff Mahoney, Sagi, and Wenwei
Tao.
- A set of updates for NVMe:
- Turn the controller state management into a proper state
machine. From Christoph.
- Shuffling of code in preparation for NVMe-over-fabrics, also
from Christoph.
- Cleanup of the command prep part from Ming Lin.
- Rewrite of the discard support from Ming Lin.
- Deadlock fix for namespace removal from Ming Lin.
- Use the now exported blk-mq tag helper for IO termination.
From Sagi.
- Various little fixes from Christoph, Guilherme, Keith, Ming
Lin, Wang Sheng-Hui.
- Convert mtip32xx to use the now exported blk-mq tag iter function,
from Keith"
* 'for-4.7/drivers' of git://git.kernel.dk/linux-block: (74 commits)
lightnvm: reserved space calculation incorrect
lightnvm: rename nr_pages to nr_ppas on nvm_rq
lightnvm: add is_cached entry to struct ppa_addr
lightnvm: expose gennvm_mark_blk to targets
lightnvm: remove mgt targets on mgt removal
lightnvm: pass dma address to hardware rather than pointer
lightnvm: do not assume sequential lun alloc.
nvme/lightnvm: Log using the ctrl named device
lightnvm: rename dma helper functions
lightnvm: enable metadata to be sent to device
lightnvm: do not free unused metadata on rrpc
lightnvm: fix out of bound ppa lun id on bb tbl
lightnvm: refactor set_bb_tbl for accepting ppa list
lightnvm: move responsibility for bad blk mgmt to target
lightnvm: make nvm_set_rqd_ppalist() aware of vblks
lightnvm: remove struct factory_blks
lightnvm: refactor device ops->get_bb_tbl()
lightnvm: introduce nvm_for_each_lun_ppa() macro
lightnvm: refactor dev->online_target to global nvm_targets
lightnvm: rename nvm_targets to nvm_tgt_type
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this merge cycle we had an interaction with MTD subsystem, that
included converting drivers/mtd/nand/nand_base.c to use newly
introduced MTD (NAND/NOR) LED trigger instead of implementing it on
its own.
Related MTD patches are intended to be merged through the LED tree,
before MTD tree is merged, since further MTD development is based on
those modifications.
Summary:
LEDs:
- Introduce a kernel panic LED trigger
- Introduce a MTD (NAND/NOR) trigger
- led-tca6507: silence an uninitialized variable warning
- ledtrig-ide-disk: Move ide_blink_delay to ledtrig_ide_activity()
- leds-ss4200: Add depend on x86 arch
- leds-ss4200: add DMI data for FSC SCALEO Home Server
- leds-triggers: Allow to switch the trigger to "panic" on a kernel panic
- devicetree: leds: Introduce "panic-indicator" optional property
- leds-gpio: Support the "panic-indicator" firmware property
MTD:
- Uninline mtd_write_oob and move it to mtdcore.c
- Remove the "nand-disk" LED trigger
- Hook I/O activity to the MTD LED trigger"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: gpio: Support the "panic-indicator" firmware property
devicetree: leds: Introduce "panic-indicator" optional property
leds: triggers: Allow to switch the trigger to "panic" on a kernel panic
leds: ss4200: add DMI data for FSC SCALEO Home Server
leds: ss4200: Add depend on x86 arch
leds: ledtrig-ide-disk: Move ide_blink_delay to ledtrig_ide_activity()
leds: tca6507: silence an uninitialized variable warning
mtd: Hook I/O activity to the MTD LED trigger
mtd: nand: Remove the "nand-disk" LED trigger
leds: trigger: Introduce a MTD (NAND/NOR) trigger
mtd: Uninline mtd_write_oob and move it to mtdcore.c
leds: trigger: Introduce a kernel panic LED trigger
|
|
Also note the GigaDevice JEDEC ID.
No write-protect support yet, since this flash uses a different status
register layout.
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Updates from Boris Brezillon:
This pull request contains the following infrastructure changes:
* introduction of the ECC algo concept to extend the ECC mode one
* replacement of the nand_ecclayout infrastructure by something more
future-proof.
* addition of an mtd-activity led trigger to replace the nand-activity
one
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* rework of the OMAP GPMC and NAND drivers
* prepare the sunxi NAND driver to receive DMA support
* handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
* tag 'nand/for-4.7' of github.com:linux-nand/linux: (152 commits)
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
mtd: nand: sh_flctl: rely on generic DT parsing done in nand_scan_ident()
mtd: nand: mxc: rely on generic DT parsing done in nand_scan_ident()
...
|
|
This is more obvious than guessing based on ECC strength. It allows
using NAND on devices with BCH-1 (e.g. D-Link DIR-885L).
This maintains DT backward compatibility by defaulting to Hamming if a
1-bit ECC algorithm is specified without a corresponding algorithm
selection. i.e., to use BCH-1, you must specify:
nand-ecc-strength = <1>;
nand-ecc-step-size = <512>;
nand-ecc-algo = "bch";
Also adds a check to ensure we haven't allowed someone to get by with SW
ECC. If we want to support SW ECC, we need to refactor some other pieces
of this driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
ECC is only calculated for written pages. As erased pages are not
actively written the ECC is always invalid. For this purpose the
Hardware BCH unit is able to check for erased pages and does not raise
an ECC error in this case. This behaviour can be influenced using the
BCH_MODE register which sets the number of allowed bitflips in an erased
page. Unfortunately the unit is not capable of fixing the bitflips in
memory.
To avoid complete software checks for erased pages, we can simply check
buffers with uncorrectable ECC errors because we know that any erased
page with errors is uncorrectable by the BCH unit.
This patch adds the generic nand_check_erased_ecc_chunk() to gpmi-nand
to correct erased pages. To have the valid data in the buffer before
using them, this patch moves the read_page_swap_end() call before the
ECC status checking for-loop.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[Squashed patches by Stefan and Boris to check ECC area]
Tested-by: Stefan Christ <s.christ@phytec.de>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
So far it was only possible to specify ECC algorithm using "soft" and
"soft_bch" values of nand-ecc-mode prop. There wasn't a way to specify
it for a hardware ECC mode.
Now that we have independent field in NAND subsystem for storing info
about ECC algorithm we may also add support for this new DT property.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This value should not be part of nand_ecc_modes_t as it specifies
algorithm not a mode. We successfully managed to introduce new "algo"
field which is respected now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
There isn't any difference between handling NAND_ECC_SOFT and
NAND_ECC_SOFT_BCH now. What matters is the new field called "algo".
Please note we're keeping backward DT compatibility. We are still
treating "soft_bch" value as the one setting Hamming algorithm, it's
just handled in of_get_nand_ecc_algo now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Now we have all drivers properly setting this new field we can start
using it. For a very short period of time we should support both values:
NAND_ECC_SOFT and NAND_ECC_SOFT_BCH treating them the same. It's because
of_get_nand_ecc_mode may still be setting NAND_ECC_SOFT_BCH.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
NAND core sets ECC algorithm in algo field now and it should be
preferred over the mode field. This also prepares driver for dropping
NAND_ECC_SOFT_BCH.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Based on DMA documentation and testing using high memory buffer when doing
dma transfers can lead to various issues including kernel panics.
To workaround this simply use cpu copy.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The prefetch engine sends a dma request once a FIFO threshold has
been met. No other requests are received until the previous request
is handled.
Starting a dma transfer (dma_async_issue_pending) results in any
previous event for the dma channel to be cleared. Therefore, starting
the prefetch engine before initiating the dma transfer may result in
the prefetch triggering a dma request but instead of it being handled
it can end up being cleared. This will result in a hang since the code
will continue to wait for the dma request to complete.
By initiating the dma request before enabling the prefetch engine this
race condition is avoided and no dma request are missed/cleared.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Add __init attribute on functions that are only called from other __init
functions and that are not inlined, at least with gcc version 4.8.4 on an
x86 machine with allyesconfig. Currently, the functions are put in the
.text.unlikely segment. Declaring them as __init will cause them to be
put in the .init.text and to disappear after initialization.
The result of objdump -x on the functions before the change is as follows:
000000000000059a l F .text.unlikely 0000000000000239 alloc_device
000000000000034e l F .text.unlikely 000000000000002e get_partition_name
00000000000007d3 l F .text.unlikely 00000000000005da init_nandsim
And after the change it is as follows:
0000000000000029 l F .init.text 0000000000000234 alloc_device
0000000000000000 l F .init.text 0000000000000029 get_partition_name
000000000000025d l F .init.text 00000000000005d5 init_nandsim
Done with the help of Coccinelle. The semantic patch checks for local
static non-init functions that are called from an __init function and are
not called from any other function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Now that all drivers go through nand_set_flash_node() to parse the generic
NAND properties, we can move all of_get_nand_xxx() helpers in to
nand_base.c, make them static and remove of_mtd.c and of_mtd.h.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Han xu <han.xu@nxp.com>
|
|
Move constants to the right of binary operators.
Generated by: scripts/coccinelle/misc/compare_const_fl.cocci
CC: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Harvey Hunt <harvey.hunt@imgtec.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Now that all MTD drivers have moved to the mtd_ooblayout_ops model we can
safely remove the struct nand_ecclayout definition, and all the remaining
places where it was still used.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Now that all NAND drivers have switched to mtd_ooblayout_ops, we can kill
the ecc->layout field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users. Modify the onenand drivers to switch to this
approach.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
|
|
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
|
|
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
