summaryrefslogtreecommitdiffstats
path: root/drivers/mtd/nand/raw
AgeCommit message (Collapse)AuthorFilesLines
2022-06-16mtd: rawnand: gpmi: Fix setting busy timeout settingSascha Hauer1-1/+1
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as: | Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY | mode. This value is the number of GPMI_CLK cycles multiplied by 4096. So instead of multiplying the value in cycles with 4096, we have to divide it by that value. Use DIV_ROUND_UP to make sure we are on the safe side, especially when the calculated value in cycles is smaller than 4096 as typically the case. This bug likely never triggered because any timeout != 0 usually will do. In my case the busy timeout in cycles was originally calculated as 2408, which multiplied with 4096 is 0x968000. The lower 16 bits were taken for the 16 bit wide register field, so the register value was 0x8000. With 2970bf5a32f0 ("mtd: rawnand: gpmi: fix controller timings setting") however the value in cycles became 2384, which multiplied with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an intermediate timeout when reading from NAND. Fixes: b1206122069aa ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation") Cc: stable@vger.kernel.org Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
2022-06-09Revert "mtd: rawnand: add support for Toshiba TC58NVG0S3HTA00 NAND flash"Christian Lamparter1-3/+0
This reverts commit 3380557fc7e28d9bce7607e16d98f123d36da4ca. It turned out this "4-byte" ID might have been an honest mistake. Regrettably, the chip Andreas has might be a counterfeit or is damaged in some other way and shouldn't have ended up in a router. Andreas reported his chip is returning just four bytes: "98 f1 80 15 00 00 00 00". However, according to Kioxia/Toshiba's datasheet, there should have been at least another byte that would have contained the correct OOB size that Andreas needed. Miquel and Andreas are both favoring reverting the patch over further, possibly hacky modifications: "[Reverting] is the safest option here. Apart from this device, we do not know how many devices have these damaged/counterfeit chips. If it is just a couple and only on Fritzboxes, as suggested in the Github issue the patch could be carried through OpenWrt[...]" Thanks to several users on the openwrt forum and github issue, who stayed along for the ride: - Peter-vdL for reporting the issue and testing patches. - neg2led and Hannu Nyman who did all the datasheet digging and debugging. Cc: Andreas Boehler <dev@aboehler.at> Suggested-by: Andreas Boehler <dev@aboehler.at> Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://github.com/openwrt/openwrt/issues/9962 Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220607185918.1048204-1-chunkeey@gmail.com
2022-05-24Merge tag 'mtd/for-5.19' of ↵Linus Torvalds20-752/+321
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux Pull mtd updates from Miquel Raynal: "MTD core changes: - Call of_platform_populate() for MTD partitions - Check devicetree alias for index - mtdoops: - Add a timestamp to the mtdoops header. - Create a header structure for the saved mtdoops. - Fix the size of the header read buffer. - mtdblock: Warn if opened on NAND - Bindings: - reserved-memory: Support MTD/block device - jedec,spi-nor: remove unneeded properties - Extend fixed-partitions binding - Add Sercomm (Suzhou) Corporation vendor prefix MTD driver changes: - st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove() - phram: - Allow cached mappings - Allow probing via reserved-memory - maps: ixp4xx: Drop driver - bcm47xxpart: Print correct offset on read error CFI driver changes: - Rename chip_ready variables - Add S29GL064N ID definition - Use chip_ready() for write on S29GL064N - Move and rename chip_check/chip_ready/chip_good_for_write NAND core changes: - Print offset instead of page number for bad blocks Raw NAND controller drivers: - Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe() - CS553X: simplify the return expression of cs553x_write_ctrl_byte() - Davinci: Remove redundant unsigned comparison to zero - Denali: Use managed device resources - GPMI: - Add large oob bch setting support - Rename the variable ecc_chunk_size - Uninline the gpmi_check_ecc function - Add strict ecc strength check - Refactor BCH geometry settings function - Intel: Fix possible null-ptr-deref in ebu_nand_probe() - MPC5121: Check before clk_disable_unprepare() not needed - Mtk: - MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK - Also parse the default nand-ecc-engine property if available - Make mtk_ecc.c a separated module - OMAP ELM: - Convert the bindings to yaml - Describe the bindings for AM64 ELM - Add support for its compatible - Renesas: Use runtime PM instead of the raw clock API and update the bindings accordingly - Rockchip: Check before clk_disable_unprepare() not needed - TMIO: Check return value after calling platform_get_resource() Raw NAND chip driver: - Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00 SPI-NAND chip drivers: - Gigadevice: - Add support for: - GD5FxGM7xExxG - GD5F{2,4}GQ5xExxG - GD5F1GQ5RExxG - GD5FxGQ4xExxG - Fix Quad IO for GD5F1GQ5UExxG - XTX: Add support for XT26G0xA SPI NOR core changes: - Read back written SR value to make sure the write was done correctly. - Introduce a common function for Read ID that manufacturer drivers can use to verify the Octal DTR switch worked correctly. - Add helpers for read/write any register commands so manufacturer drivers don't open code it every time. - Clarify rdsr dummy cycles documentation. - Add debugfs entry to expose internal flash parameters and state. SPI NOR manufacturer drivers changes: - Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A. - Move spi_nor_write_ear() to Winbond module since only Winbond flashes use it. - Rework Micron and Cypress Octal DTR enable methods to improve readability. - Use the common Read ID function to verify switch to Octal DTR mode for Micron and Cypress flashes. - Skip polling status on volatile register writes for Micron and Cypress flashes since the operation is instant" * tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits) mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove() dt-bindings: mtd: partitions: Extend fixed-partitions binding dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix mtd: phram: Allow cached mappings mtd: call of_platform_populate() for MTD partitions mtd: rawnand: renesas: Use runtime PM instead of the raw clock API dt-bindings: mtd: renesas: Fix the NAND controller description mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte() mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4 mtd: spi-nor: debugfs: fix format specifier mtd: spi-nor: support eon en25qh256a variant mtd: spi-nor: winbond: add support for W25Q512NW-IM mtd: spi-nor: expose internal parameters via debugfs mtd: spi-nor: export spi_nor_hwcaps_pp2cmd() mtd: spi-nor: move spi_nor_write_ear() to winbond module mtd: spi-nor: amend the rdsr dummy cycles documentation mtd: cfi_cmdset_0002: Rename chip_ready variables ...
2022-05-16mtd: rawnand: renesas: Use runtime PM instead of the raw clock APIMiquel Raynal1-28/+23
This NAND controller is part of a well defined power domain handled by the runtime PM core. Let's keep the harmony with the other RZ/N1 drivers and exclusively use the runtime PM API to enable/disable the clocks. We still need to retrieve the external clock rate in order to derive the NAND timings, but that is not a big deal, we can still do that in the probe and just save this value to reuse it later. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/linux-mtd/20220513104957.257721-3-miquel.raynal@bootlin.com
2022-05-16mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not neededPhil Edworthy1-2/+1
All code in clk_disable_unprepare() already checks the clk ptr using IS_ERR_OR_NULL so there is no need to check it again before calling it. A lot of other drivers already rely on this behaviour, so it's safe to do so here. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220512185033.46901-1-phil.edworthy@renesas.com
2022-05-16mtd: rawnand: rockchip: Check before clk_disable_unprepare() not neededPhil Edworthy1-4/+2
All code in clk_disable_unprepare() already checks the clk ptr using IS_ERR_OR_NULL so there is no need to check it again before calling it. A lot of other drivers already rely on this behaviour, so it's safe to do so here. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220512184558.45966-1-phil.edworthy@renesas.com
2022-05-12mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()Minghao Chi1-6/+1
Simplify the return expression. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220505022354.61458-1-chi.minghao@zte.com.cn
2022-05-12mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4Rickard x Andersson2-2/+7
Add timings for Kioxia/Toshiba TH58NVG3S0HBAI4. Timings for this memory matches the timings selected for TH58NVG2S3HBAI4. This patch increases eraseblock write speed from 5248 KiB/s to 6864 KiB/s and erase block read speed from 8542 KiB/s to 18360 KiB/s Tested on i.MX6SX. Signed-off-by: Rickard x Andersson <rickaran@axis.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220429083931.26795-1-rickaran@axis.com
2022-04-27Merge tag 'mtd/mtk-spi-nand-for-5.19' into nand/nextMiquel Raynal5-642/+3
Mediatek ECC changes: * Also parse the default nand-ecc-engine property if available * Make mtk_ecc.c a separated module Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2022-04-27mtd: nand: make mtk_ecc.c a separated moduleChuanhong Guo5-642/+3
this code will be used in mediatek snfi spi-mem controller with pipelined ECC engine. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220424032527.673605-2-gch981213@gmail.com
2022-04-27mtd: rawnand: tmio: check return value after calling platform_get_resource()Yang Yingliang1-0/+3
It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-3-yangyingliang@huawei.com
2022-04-27mtd: rawnand: intel: fix possible null-ptr-deref in ebu_nand_probe()Yang Yingliang1-1/+1
It will cause null-ptr-deref when using 'res', if platform_get_resource() returns NULL, so move using 'res' after devm_ioremap_resource() that will check it to avoid null-ptr-deref. Fixes: 0b1039f016e8 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-2-yangyingliang@huawei.com
2022-04-27mtd: rawnand: cadence: fix possible null-ptr-deref in cadence_nand_dt_probe()Yang Yingliang1-3/+2
It will cause null-ptr-deref when using 'res', if platform_get_resource() returns NULL, so move using 'res' after devm_ioremap_resource() that will check it to avoid null-ptr-deref. And use devm_platform_get_and_ioremap_resource() to simplify code. Fixes: ec4ba01e894d ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-1-yangyingliang@huawei.com
2022-04-21mtd: rawnand: add support for Toshiba TC58NVG0S3HTA00 NAND flashAndreas Böhler1-0/+3
The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash has 128 bytes OOB. This adds a static NAND ID entry to correct this. Tested on FRITZ!Box 7530 flashed with OpenWrt. Signed-off-by: Andreas Böhler <dev@aboehler.at> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220420104034.6333-1-dev@aboehler.at
2022-04-21mtd: rawnand: gpmi: Add large oob bch setting supportHan Xu2-5/+197
The code change proposes a new way to set bch geometry for large oob NAND (oobsize > 1KB). In this case, previous implementation can NOT guarantee the bad block mark always locates in data chunk, so we need a new way to do it. The general idea is, 1.Try all ECC strength from the maximum ecc that controller can support to minimum value required by NAND chip, any ECC strength makes the BBM locate in data chunk can be eligible. 2.If none of them works, using separate ECC for meta, which will add one extra ecc with the same ECC strength as other data chunks. This extra ECC can guarantee BBM located in data chunk, also we need to check if oob can afford it. Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-6-han.xu@nxp.com
2022-04-21mtd: rawnand: gpmi: Rename the variable ecc_chunk_sizeHan Xu2-27/+34
There is only one variable ecc_chunk_size in bch_geometry data structure but two different field in BCH registers. The data0_size in BCH_FLASH0LAYOUT0 and datan_size in BCH_FLASH0LAYOUT1 should have dedicate variable since they might set to different values in some cases. For instance, if need dedicate ecc for meta area, the data0_size should be 0 rather than datan_size, but for all other cases, data0_size still equals to datan_size and it won't bring any function change. Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-5-han.xu@nxp.com
2022-04-21mtd: rawnand: gpmi: Uninline the gpmi_check_ecc functionHan Xu1-1/+1
The gpmi_check_ecc() is not small after adding more strict ecc check, uninline it. Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-4-han.xu@nxp.com
2022-04-21mtd: rawnand: gpmi: Add strict ecc strength checkHan Xu1-1/+14
Add nand_ecc_is_strong_enough() check in gpmi_check_ecc() function to make sure ecc strength can meet chip requirement. Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-3-han.xu@nxp.com
2022-04-21mtd: rawnand: gpmi: Refactor bch geometry settings functionHan Xu1-12/+20
The code change refactor the bch geometry setting function, which doesn't change the default behavior, while user may choose to use chips required minimum ecc strength by DT flag "fsl,use-minimum-ecc". The default way to set bch geometry need to set the data chunk size(step_size) larger than oob size to make sure BBM locates in data chunk, then set the maximum ecc strength oob can hold. It always use unbalanced ECC layout, which ecc0 will cover both meta and data0 chunk. But the default bch setting is deprecated for large oobsize NAND (oobsize >1KB), so in the patch set, there is a split commit that introduces a new way to set bch geometry for large oob size NAND. For all other cases,set the bch geometry by chip required strength and step size, which uses the minimum ecc strength chip required. It can be explicitly enabled by DT flag "fsl,use-minimum-ecc", but need to be en/disabled in both u-boot and kernel at the same time. Signed-off-by: Han Xu <han.xu@nxp.com> Tested-by: Sean Nyekjaer <sean@geanix.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-2-han.xu@nxp.com
2022-04-21mtd: rawnand: denali: Use managed device resourcesZheyu Ma1-11/+4
All of the resources used by this driver has managed interfaces, so use them. Otherwise we will get the following splat: [ 4.472703] denali-nand-pci 0000:00:05.0: timeout while waiting for irq 0x1000 [ 4.474071] denali-nand-pci: probe of 0000:00:05.0 failed with error -5 [ 4.473538] nand: No NAND device found [ 4.474068] BUG: unable to handle page fault for address: ffffc90005000410 [ 4.475169] #PF: supervisor write access in kernel mode [ 4.475579] #PF: error_code(0x0002) - not-present page [ 4.478362] RIP: 0010:iowrite32+0x9/0x50 [ 4.486068] Call Trace: [ 4.486269] <IRQ> [ 4.486443] denali_isr+0x15b/0x300 [denali] [ 4.486788] ? denali_direct_write+0x50/0x50 [denali] [ 4.487189] __handle_irq_event_percpu+0x161/0x3b0 [ 4.487571] handle_irq_event+0x7d/0x1b0 [ 4.487884] handle_fasteoi_irq+0x2b0/0x770 [ 4.488219] __common_interrupt+0xc8/0x1b0 [ 4.488549] common_interrupt+0x9a/0xc0 Fixes: 93db446a424c ("mtd: nand: move raw NAND related code to the raw/ subdir") Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220411125808.958276-1-zheyuma97@gmail.com
2022-04-21mtd: rawnand: qcom: fix memory corruption that causes panicMd Sadre Alam1-11/+13
This patch fixes a memory corruption that occurred in the nand_scan() path for Hynix nand device. On boot, for Hynix nand device will panic at a weird place: | Unable to handle kernel NULL pointer dereference at virtual address 00000070 | [00000070] *pgd=00000000 | Internal error: Oops: 5 [#1] PREEMPT SMP ARM | Modules linked in: | CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0 #38 | Hardware name: Generic DT based system | PC is at nandc_set_reg+0x8/0x1c | LR is at qcom_nandc_command+0x20c/0x5d0 | pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113 | sp : c14adc50 ip : c14ee208 fp : c0cc970c | r10: 000000a3 r9 : 00000000 r8 : 00000040 | r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040 | r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040 | Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none | Control: 10c5387d Table: 8020406a DAC: 00000051 | Register r0 information: slab kmalloc-2k start c14ee000 pointer offset 64 size 2048 | Process swapper/0 (pid: 1, stack limit = 0x(ptrval)) | nandc_set_reg from qcom_nandc_command+0x20c/0x5d0 | qcom_nandc_command from nand_readid_op+0x198/0x1e8 | nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78 | hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454 | hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8 | nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0 | qcom_nandc_probe from platform_probe+0x58/0xac The problem is that the nand_scan()'s qcom_nand_attach_chip callback is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size. This causes the sg_init_table of clear_bam_transaction() in the driver's qcom_nandc_command() to memset much more than what was initially allocated by alloc_bam_transaction(). This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page size in qcom_nand_attach_chip call back after freeing the previously allocated memory for bam txn as per nandc->max_cwperpage = 1 and then again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on page size in qcom_nand_attach_chip call back itself. Cc: stable@vger.kernel.org Fixes: 6a3cec64f18c ("mtd: rawnand: qcom: convert driver to nand_scan()") Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Co-developed-by: Sricharan R <quic_srichara@quicinc.com> Signed-off-by: Sricharan R <quic_srichara@quicinc.com> Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com
2022-04-21mtd: rawnand: Fix return value check of wait_for_completion_timeoutMiaoqian Lin1-6/+8
wait_for_completion_timeout() returns unsigned long not int. It returns 0 if timed out, and positive if completed. The check for <= 0 is ambiguous and should be == 0 here indicating timeout which is the only error case. Fixes: 83738d87e3a0 ("mtd: sh_flctl: Add DMA capabilty") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com
2022-04-11mtd: rawnand: omap_elm: Add compatible for AM64 ELMRoger Quadros1-0/+1
The AM64 SoC has the Error Locator Module. Add compatible id for it. Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220326080726.30372-4-rogerq@kernel.org
2022-04-04mtd: rawnand: fix ecc parameters for mt7622Chuanhong Guo1-4/+8
According to the datasheet, mt7622 only has 5 ECC capabilities instead of 7, and the decoding error register is arranged as follows: +------+---------+---------+---------+---------+ | Bits | 19:15 | 14:10 | 9:5 | 4:0 | +------+---------+---------+---------+---------+ | Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 | +------+---------+---------+---------+---------+ This means err_mask should be 0x1f instead of 0x3f and the number of bits shifted in mtk_ecc_get_stats should be 5 instead of 8. This commit introduces err_shift for the difference in this register and fix other existing parameters. Public MT7622 reference manual can be found on [0] and the info this commit is based on is from page 656 and page 660. [0]: https://wiki.banana-pi.org/Banana_Pi_BPI-R64#Documents Fixes: 98dea8d71931 ("mtd: nand: mtk: Support MT7622 NAND flash controller.") Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220402160315.919094-1-gch981213@gmail.com
2022-04-04mtd: rawnand: print offset instead of page number for bad blocksRafał Miłecki1-4/+5
This makes printed info consistent with other kernel messages. After scanning NAND BBT create_bbt() prints offset of each bad block. This change makes is easy to verify nand_erase_nand() failure reason. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220326163304.30806-1-zajec5@gmail.com
2022-04-04mtd: rawnand: davinci: Remove redundant unsigned comparison to zeroWang Weiyang1-1/+1
Since core_chipsel is uint32_t, comparison to zero is redundant Signed-off-by: Wang Weiyang <wangweiyang2@huawei.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220317113907.96006-1-wangweiyang2@huawei.com
2022-03-25Merge tag 'mtd/changes-for-5.18' of ↵Linus Torvalds21-150/+428
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux Pull MTD updates from Miquel Raynal: "There has been a lot of activity in the MTD subsystem recently, with a number of SPI-NOR cleanups as well as the introduction of ECC engines that can be used by SPI controllers (hence a few SPI patches in here). Core MTD changes: - Replace the expert mode symbols with a single helper - Fix misuses of of_match_ptr() - Remove partid and partname debugfs files - tests: Fix eraseblock read speed miscalculation for lower partition sizes - TRX parser: Allow to use on MediaTek MIPS SoCs MTD driver changes: - spear_smi: use GFP_KERNEL - mchp48l640: Add SPI ID table - mchp23k256: Add SPI ID table - blkdevs: Avoid soft lockups with some mtd/spi devices - aspeed-smc: Improve probe resilience Hyperbus changes: - HBMC_AM654 should depend on ARCH_K3 NAND core changes: - ECC: - Add infrastructure to support hardware engines - Add a new helper to retrieve the ECC context - Provide a helper to retrieve a pilelined engine device NAND-ECC changes: - Macronix ECC engine: - Add Macronix external ECC engine support - Support SPI pipelined mode - Make two read-only arrays static const - Fix compile test issue Raw NAND core changes: - Fix misuses of of_match_node() - Rework of_get_nand_bus_width() - Remove of_get_nand_on_flash_bbt() wrapper - Protect access to rawnand devices while in suspend - bindings: Document the wp-gpios property Rax NAND controller driver changes: - atmel: Fix refcount issue in atmel_nand_controller_init - nandsim: - Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern - Merge repeat codes in ns_switch_state - Replace overflow check with kzalloc to single kcalloc - rockchip: Fix platform_get_irq.cocci warning - stm32_fmc2: Add NAND Write Protect support - pl353: Set the nand chip node as the flash node - brcmnand: Fix sparse warnings in bcma_nand - omap_elm: Remove redundant variable 'errors' - gpmi: - Support fast edo timings for mx28 - Validate controller clock rate - Fix controller timings setting - brcmnand: - Add BCMA shim - BCMA controller uses command shift of 0 - Allow platform data instantation - Add platform data structure for BCMA - Allow working without interrupts - Move OF operations out of brcmnand_init_cs() - Avoid pdev in brcmnand_init_cs() - Allow SoC to provide I/O operations - Assign soc as early as possible Onenand changes: - Check for error irq SPI-NAND core changes: - Delay a little bit the dirmap creation - Create direct mapping descriptors for ECC operations SPI-NAND driver changes: - macronix: Use random program load SPI NOR core changes: - Move vendor specific code out of the core into vendor drivers. - Unify all function and object names in the vendor modules. - Make setup() callback optional to improve readability. - Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash declaration. SPI changes: - Macronix SPI controller: - Fix the transmit path - Create a helper to configure the controller before an operation - Create a helper to ease the start of an operation - Add support for direct mapping - Add support for pipelined ECC operations - spi-mem: - Introduce a capability structure - Check the controller extra capabilities - cadence-quadspi/mxic: Provide capability structures - Kill the spi_mem_dtr_supports_op() helper - Add an ecc parameter to the spi_mem_op structure Binding changes: - Dropped mtd/cortina,gemini-flash.txt - Convert BCM47xx partitions to json-schema - Vendor prefixes: Clarify Macronix prefix - SPI NAND: Convert spi-nand description file to yaml - Raw NAND chip: Create a NAND chip description - Raw NAND controller: - Harmonize the property types - Fix a comment in the examples - Fix the reg property description - Describe Macronix NAND ECC engine - Macronix SPI controller: - Document the nand-ecc-engine property - Convert to yaml - The interrupt property is not mandatory" * tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits) mtd: nand: ecc: mxic: Fix compile test issue mtd: nand: mxic-ecc: make two read-only arrays static const mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3 mtd: core: Remove partid and partname debugfs files dt-bindings: mtd: partitions: convert BCM47xx to the json-schema mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init mtd: rawnand: rockchip: fix platform_get_irq.cocci warning mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set mtd: spi-nor: renumber flags mtd: spi-nor: slightly change code style in spi_nor_sr_ready() mtd: spi-nor: spansion: rename vendor specific functions and defines mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag mtd: spi-nor: move all spansion specifics into spansion.c mtd: spi-nor: spansion: slightly rework control flow in late_init() mtd: spi-nor: micron-st: rename vendor specific functions and defines mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag mtd: spi-nor: move all micron-st specifics into micron-st.c mtd: spi-nor: xilinx: correct the debug message mtd: spi-nor: xilinx: rename vendor specific functions and defines ...
2022-03-23Merge tag 'nand/for-5.18' into mtd/nextMiquel Raynal13-137/+415
Raw NAND core changes: * Rework of_get_nand_bus_width() * Remove of_get_nand_on_flash_bbt() wrapper * Protect access to rawnand devices while in suspend * bindings: Document the wp-gpios property Rax NAND controller driver changes: * atmel: Fix refcount issue in atmel_nand_controller_init * nandsim: - Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern - Merge repeat codes in ns_switch_state - Replace overflow check with kzalloc to single kcalloc * rockchip: Fix platform_get_irq.cocci warning * stm32_fmc2: Add NAND Write Protect support * pl353: Set the nand chip node as the flash node * brcmnand: Fix sparse warnings in bcma_nand * omap_elm: Remove redundant variable 'errors' * gpmi: - Support fast edo timings for mx28 - Validate controller clock rate - Fix controller timings setting * brcmnand: - Add BCMA shim - BCMA controller uses command shift of 0 - Allow platform data instantation - Add platform data structure for BCMA - Allow working without interrupts - Move OF operations out of brcmnand_init_cs() - Avoid pdev in brcmnand_init_cs() - Allow SoC to provide I/O operations - Assign soc as early as possible Onenand changes: * Check for error irq Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2022-03-21Merge tag 'for-5.18/block-2022-03-18' of git://git.kernel.dk/linux-blockLinus Torvalds1-1/+0
Pull block updates from Jens Axboe: - BFQ cleanups and fixes (Yu, Zhang, Yahu, Paolo) - blk-rq-qos completion fix (Tejun) - blk-cgroup merge fix (Tejun) - Add offline error return value to distinguish it from an IO error on the device (Song) - IO stats fixes (Zhang, Christoph) - blkcg refcount fixes (Ming, Yu) - Fix for indefinite dispatch loop softlockup (Shin'ichiro) - blk-mq hardware queue management improvements (Ming) - sbitmap dead code removal (Ming, John) - Plugging merge improvements (me) - Show blk-crypto capabilities in sysfs (Eric) - Multiple delayed queue run improvement (David) - Block throttling fixes (Ming) - Start deprecating auto module loading based on dev_t (Christoph) - bio allocation improvements (Christoph, Chaitanya) - Get rid of bio_devname (Christoph) - bio clone improvements (Christoph) - Block plugging improvements (Christoph) - Get rid of genhd.h header (Christoph) - Ensure drivers use appropriate flush helpers (Christoph) - Refcounting improvements (Christoph) - Queue initialization and teardown improvements (Ming, Christoph) - Misc fixes/improvements (Barry, Chaitanya, Colin, Dan, Jiapeng, Lukas, Nian, Yang, Eric, Chengming) * tag 'for-5.18/block-2022-03-18' of git://git.kernel.dk/linux-block: (127 commits) block: cancel all throttled bios in del_gendisk() block: let blkcg_gq grab request queue's refcnt block: avoid use-after-free on throttle data block: limit request dispatch loop duration block/bfq-iosched: Fix spelling mistake "tenative" -> "tentative" sr: simplify the local variable initialization in sr_block_open() block: don't merge across cgroup boundaries if blkcg is enabled block: fix rq-qos breakage from skipping rq_qos_done_bio() block: flush plug based on hardware and software queue order block: ensure plug merging checks the correct queue at least once block: move rq_qos_exit() into disk_release() block: do more work in elevator_exit block: move blk_exit_queue into disk_release block: move q_usage_counter release into blk_queue_release block: don't remove hctx debugfs dir from blk_mq_exit_queue block: move blkcg initialization/destroy into disk allocation/release handler sr: implement ->free_disk to simplify refcounting sd: implement ->free_disk to simplify refcounting sd: delay calling free_opal_dev sd: call sd_zbc_release_disk before releasing the scsi_device reference ...
2022-03-18Merge tag 'spi-nor/for-5.18' into mtd/nextMiquel Raynal5-12/+17
SPI NOR core changes: - move vendor specific code out of the core into vendor drivers. - unify all function and object names in the vendor modules. - make setup() callback optional to improve readability. - skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash declaration. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2022-03-14mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_initXin Xiong1-3/+11
The reference counting issue happens in several error handling paths on a refcounted object "nc->dmac". In these paths, the function simply returns the error code, forgetting to balance the reference count of "nc->dmac", increased earlier by dma_request_channel(), which may cause refcount leaks. Fix it by decrementing the refcount of specific object in those error paths. Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Co-developed-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Co-developed-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220304085330.3610-1-xiongx18@fudan.edu.cn
2022-03-14mtd: rawnand: rockchip: fix platform_get_irq.cocci warningYihao Han1-1/+0
Remove dev_err() messages after platform_get_irq*() failures. platform_get_irq() already prints an error. Generated by: scripts/coccinelle/api/platform_get_irq.cocci Signed-off-by: Yihao Han <hanyihao@vivo.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220303123431.3170-1-hanyihao@vivo.com
2022-03-07mtd: rawnand: omap2: Actually prevent invalid configuration and build errorRoger Quadros1-2/+1
The root of the problem is that we are selecting symbols that have dependencies. This can cause random configurations that can fail. The cleanest solution is to avoid using select. This driver uses interfaces from the OMAP_GPMC driver so we have to depend on it instead. Fixes: 4cd335dae3cf ("mtd: rawnand: omap2: Prevent invalid configuration and build error") Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Tested-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/linux-mtd/20220219193600.24892-1-rogerq@kernel.org
2022-02-18mtd: rawnand: stm32_fmc2: Add NAND Write Protect supportChristophe Kerello1-1/+39
This patch adds the support of the WP# signal. WP will be disabled in probe/resume callbacks and will be enabled in remove/suspend callbacks. Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220217144755.270679-3-christophe.kerello@foss.st.com
2022-02-18mtd: rawnand: pl353: Set the nand chip node as the flash nodeAmit Kumar Mahapatra1-1/+1
In devicetree the flash information is embedded within nand chip node, so during nand chip initialization the nand chip node should be passed to nand_set_flash_node() api, instead of nand controller node. Fixes: 08d8c62164a3 ("mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller") Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220209053427.27676-1-amit.kumar-mahapatra@xilinx.com
2022-02-09mtd: rawnand: protect access to rawnand devices while in suspendSean Nyekjaer1-24/+20
Prevent rawnand access while in a suspended state. Commit 013e6292aaf5 ("mtd: rawnand: Simplify the locking") allows the rawnand layer to return errors rather than waiting in a blocking wait. Tested on a iMX6ULL. Fixes: 013e6292aaf5 ("mtd: rawnand: Simplify the locking") Signed-off-by: Sean Nyekjaer <sean@geanix.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220208085213.1838273-1-sean@geanix.com
2022-02-07mtd: Replace the expert mode symbols with a single helperMiquel Raynal2-2/+2
Reduce the number of exported symbols by replacing: - mtd_expert_analysis_warning (the error string) - mtd_expert_analysis_mode (the boolean) with a single helper: - mtd_check_expert_analysis_mode Calling this helper will both check/return the content of the internal boolean -which is not exported anymore- and as well conditionally WARN_ONCE() the user, like it was done before. While on this function, make the error string local to the helper and set it const. Only export this helper when CONFIG_DEBUG_FS is defined to limit the growth of the Linux kernel size only for a debug feature on production kernels. Mechanically update all the consumers. Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220128113414.1121924-1-miquel.raynal@bootlin.com
2022-02-02block: remove genhd.hChristoph Hellwig1-1/+0
There is no good reason to keep genhd.h separate from the main blkdev.h header that includes it. So fold the contents of genhd.h into blkdev.h and remove genhd.h entirely. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20220124093913.742411-4-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk>
2022-01-31mtd: rawnand: Fix misuses of of_match_node()Miquel Raynal3-3/+3
On non-OF enabled platforms (CONFIG_OF is not set), of_match_node() will expand to NULL. The of_device_id array pointed by the macro will then be left unused. Let's mark the array __maybe_unused in this case to prevent compiler warnings. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/linux-mtd/20220127110802.1064963-1-miquel.raynal@bootlin.com
2022-01-31mtd: Fix misuses of of_match_ptr()Miquel Raynal8-8/+8
of_match_ptr() either expands to NULL if !CONFIG_OF, or is transparent otherwise. There are several drivers using this macro which keep their of_device_id array enclosed within an #ifdef CONFIG_OF check, these are considered fine. However, When misused, the of_device_id array pointed by this macro will produce a warning because it is finally unused when compiled without OF support. A number of fixes are possible: - Always depend on CONFIG_OF, but this will not always work and may break boards. - Enclose the compatible array by #ifdef's, this may save a bit of memory but will reduce build coverage. - Tell the compiler the array may be unused, if this can be avoided, let's not do this. - Just drop the macro, setting the of_device_id array for a non OF enabled platform is not an issue, it will just be unused. The latter solution seems the more appropriate, so let's use it. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Pratyush Yadav <p.yadav@ti.com> Link: https://lore.kernel.org/linux-mtd/20220127110631.1064705-1-miquel.raynal@bootlin.com
2022-01-31mtd: rawnand: brcmnand: Fixed incorrect sub-page ECC statusdavid regan1-1/+1
The brcmnand driver contains a bug in which if a page (example 2k byte) is read from the parallel/ONFI NAND and within that page a subpage (512 byte) has correctable errors which is followed by a subpage with uncorrectable errors, the page read will return the wrong status of correctable (as opposed to the actual status of uncorrectable.) The bug is in function brcmnand_read_by_pio where there is a check for uncorrectable bits which will be preempted if a previous status for correctable bits is detected. The fix is to stop checking for bad bits only if we already have a bad bits status. Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller") Signed-off-by: david regan <dregan@mail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/trinity-478e0c09-9134-40e8-8f8c-31c371225eda-1643237024774@3c-app-mailcom-lxa02
2022-01-26mtd: rawnand: brcmnand: Fix sparse warnings in bcma_nandFlorian Fainelli1-2/+2
sparse was unhappy about the way we woulc call cpu_to_be32/be32_to_cpu, apply the appropriate casting to silence the warnings. Reported-by: kernel test robot <lkp@intel.com> Link: https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org/thread/ZNHPJFYLO64EGI5QUT7HZ63J7O5J2G7N/ Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220125225243.15201-1-f.fainelli@gmail.com
2022-01-26mtd: rawnand: gpmi: don't leak PM reference in error pathChristian Eggers1-1/+2
If gpmi_nfc_apply_timings() fails, the PM runtime usage counter must be dropped. Reported-by: Pavel Machek <pavel@denx.de> Fixes: f53d4c109a66 ("mtd: rawnand: gpmi: Add ERR007117 protection for nfc_apply_timings") Signed-off-by: Christian Eggers <ceggers@arri.de> Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220125081619.6286-1-ceggers@arri.de
2022-01-25mtd: rawnand: omap2: Prevent invalid configuration and build errorRoger Quadros1-1/+2
We need to select MEMORY as well otherwise OMAP_GPMC will not be built. For simplicity let's select MEMORY and OMAP_GPMC unconditionally as this driver depends on OMAP_GPMC driver and uses symbols from there. Fixes: dbcb124acebd ("mtd: rawnand: omap2: Select GPMC device driver for ARCH_K3") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220118123525.8020-1-rogerq@kernel.org
2022-01-25mtd: rawnand: qcom: Fix clock sequencing in qcom_nandc_probe()Bryan O'Donoghue1-8/+6
Interacting with a NAND chip on an IPQ6018 I found that the qcomsmem NAND partition parser was returning -EPROBE_DEFER waiting for the main smem driver to load. This caused the board to reset. Playing about with the probe() function shows that the problem lies in the core clock being switched off before the nandc_unalloc() routine has completed. If we look at how qcom_nandc_remove() tears down allocated resources we see the expected order is qcom_nandc_unalloc(nandc); clk_disable_unprepare(nandc->aon_clk); clk_disable_unprepare(nandc->core_clk); dma_unmap_resource(&pdev->dev, nandc->base_dma, resource_size(res), DMA_BIDIRECTIONAL, 0); Tweaking probe() to both bring up and tear-down in that order removes the reset if we end up deferring elsewhere. Fixes: c76b78d8ec05 ("mtd: nand: Qualcomm NAND controller driver") Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220103030316.58301-2-bryan.odonoghue@linaro.org
2022-01-25mtd: rawnand: ingenic: Fix missing put_device in ingenic_ecc_getMiaoqian Lin1-1/+6
If of_find_device_by_node() succeeds, ingenic_ecc_get() doesn't have a corresponding put_device(). Thus add put_device() to fix the exception handling. Fixes: 15de8c6efd0e ("mtd: rawnand: ingenic: Separate top-level and SoC specific code") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211230072751.21622-1-linmq006@gmail.com
2022-01-23mtd: rawnand: omap_elm: remove redundant variable 'errors'Colin Ian King1-3/+1
The variable 'errors' is being used to sum the number of errors but it is never used afterwards. This can be considered a redundant set of operations and can be removed. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211221181340.524639-1-colin.i.king@gmail.com
2022-01-23mtd: rawnand: gpmi: support fast edo timings for mx28Dario Binacchi1-2/+2
In the i.MX28 manual (MCIMX28RM, Rev. 1, 2010) you can find an example (15.2.4 High-Speed NAND Timing) of how to configure the GPMI controller to manage High-Speed ​​NAND devices, so it was wrong to assume that only i.MX6 can achieve EDO timings. This patch has been tested on a 2048/64 byte NAND (Micron MT29F2G08ABAEAH4). Kernel mtd tests: - mtd_nandbiterrs - mtd_nandecctest - mtd_oobtest - mtd_pagetest - mtd_readtest - mtd_speedtest - mtd_stresstest - mtd_subpagetest - mtd_torturetest [cycles_count = 10000000] run without errors. Before this patch (mode 0): --------------------------- eraseblock write speed is 2098 KiB/s eraseblock read speed is 2680 KiB/s page write speed is 1689 KiB/s page read speed is 2522 KiB/s 2 page write speed is 1899 KiB/s 2 page read speed is 2579 KiB/s erase speed is 128000 KiB/s 2x multi-block erase speed is 73142 KiB/s 4x multi-block erase speed is 204800 KiB/s 8x multi-block erase speed is 256000 KiB/s 16x multi-block erase speed is 256000 KiB/s 32x multi-block erase speed is 256000 KiB/s 64x multi-block erase speed is 256000 KiB/s After this patch (mode 5): ------------------------- eraseblock write speed is 3390 KiB/s eraseblock read speed is 5688 KiB/s page write speed is 2680 KiB/s page read speed is 4876 KiB/s 2 page write speed is 2909 KiB/s 2 page read speed is 5224 KiB/s erase speed is 170666 KiB/s 2x multi-block erase speed is 204800 KiB/s 4x multi-block erase speed is 256000 KiB/s 8x multi-block erase speed is 256000 KiB/s 16x multi-block erase speed is 256000 KiB/s 32x multi-block erase speed is 256000 KiB/s 64x multi-block erase speed is 256000 KiB/s Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-5-dario.binacchi@amarulasolutions.com
2022-01-23mtd: rawnand: gpmi: validate controller clock rateDario Binacchi1-4/+18
What to do when the real rate of the gpmi clock is not equal to the required one? The solutions proposed in [1] did not lead to a conclusion on how to validate the clock rate, so, inspired by the document [2], I consider the rate correct only if not lower or equal to the rate of the previous edo mode. In fact, in chapter 4.16.2 (NV-DDR) of the document [2], it is written that "If the host selects timing mode n, then its clock period shall be faster than the clock period of timing mode n-1 and slower than or equal to the clock period of timing mode n.". I thought that it could therefore also be used in this case, without therefore having to define the valid rate ranges empirically. For example, suppose that gpmi_nfc_compute_timings() is called to set edo mode 5 (100MHz) but the rate returned by clk_round_rate() is 80MHz (edo mode 4). In this case gpmi_nfc_compute_timings() will return error, and will be called again to set edo mode 4, which this time will be successful. [1] https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org [2] http://www.onfi.org/-/media/client/onfi/specs/onfi_3_0_gold.pdf?la=en Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-4-dario.binacchi@amarulasolutions.com
2022-01-23mtd: rawnand: gpmi: fix controller timings settingDario Binacchi1-0/+3
Set the controller registers according to the real clock rate. The controller registers configuration (setup, hold, timeout, ... cycles) depends on the clock rate of the GPMI. Using the real rate instead of the ideal one, avoids that this inaccuracy (required_rate - real_rate) affects the registers setting. This patch has been tested on two custom boards with i.MX28 and i.MX6 SOCs: - i.MX28: required rate 100MHz, real rate 99.3MHz - i.MX6 required rate 100MHz, real rate 99MHz Fixes: b1206122069a ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation") Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-3-dario.binacchi@amarulasolutions.com
generated by cgit v1.2.3 (git 2.39.1) at 2024-09-21 20:34:43 +0000