summaryrefslogtreecommitdiffstats
path: root/drivers/mmc/host/sdhci-esdhc-imx.c
AgeCommit message (Collapse)AuthorFilesLines
2019-08-06mmc: sdhci-sprd: Fix the incorrect soft reset operation when runtime resumingBaolin Wang1-1/+1
The SD host controller specification defines 3 types software reset: software reset for data line, software reset for command line and software reset for all. Software reset for all means this reset affects the entire Host controller except for the card detection circuit. In sdhci_runtime_resume_host() we always do a software "reset for all", which causes the Spreadtrum variant controller to work abnormally after resuming. To fix the problem, let's do a software reset for the data and the command part, rather than "for all". However, as sdhci_runtime_resume() is a common sdhci function and we don't want to change the behaviour for other variants, let's introduce a new in-parameter for it. This enables the caller to decide if a "reset for all" shall be done or not. Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-05-06mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULPBOUGH CHEN1-3/+8
Add HS400 support for iMX7ULP B0. According to IC suggest, need to clear the STROBE_DLL_CTRL_RESET before any setting of STROBE_DLL_CTRL register. USDHC has register bits(bit[27~20] of register STROBE_DLL_CTRL) for slave sel value. If this register bits value is 0, it needs 256 ref_clk cycles to update slave sel value. IC suggest to set bit[27~20] to 0x4, it only need 4 ref_clk cycle to update slave sel value. This will short the lock time of slave. i.MX7ULP B0 will need more time to lock the REF and SLV, so change to add 5us delay. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-05-06mmc: sdhci-esdhc-imx: add pm_qos to interact with cpuidleBOUGH CHEN1-1/+31
On some SoCs such as i.MX7ULP, there is no busfreq driver, but cpuidle has some levels which may disable system/bus clocks, so need to add pm_qos to prevent cpuidle from entering low level idles and make sure system/bus clocks are enabled when usdhc is active. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-28Merge branch 'fixes' into nextUlf Hansson1-4/+5
2019-02-28mmc: sdhci-esdhc-imx: correct the fix of ERR004536BOUGH CHEN1-4/+5
Commit 18094430d6b5 ("mmc: sdhci-esdhc-imx: add ADMA Length Mismatch errata fix") involve the fix of ERR004536, but the fix is incorrect. Double confirm with IC, need to clear the bit 7 of register 0x6c rather than set this bit 7. Here is the definition of bit 7 of 0x6c: 0: enable the new IC fix for ERR004536 1: do not use the IC fix, keep the same as before Find this issue on i.MX845s-evk board when enable CMDQ, and let system in heavy loading. root@imx8mmevk:~# dd if=/dev/mmcblk2 of=/dev/null bs=1M & root@imx8mmevk:~# memtester 1000M > /dev/zero & root@imx8mmevk:~# [ 139.897220] mmc2: cqhci: timeout for tag 16 [ 139.901417] mmc2: cqhci: ============ CQHCI REGISTER DUMP =========== [ 139.907862] mmc2: cqhci: Caps: 0x0000310a | Version: 0x00000510 [ 139.914311] mmc2: cqhci: Config: 0x00001001 | Control: 0x00000000 [ 139.920753] mmc2: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006 [ 139.927193] mmc2: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000 [ 139.933634] mmc2: cqhci: TDL base: 0x7809c000 | TDL up32: 0x00000000 [ 139.940073] mmc2: cqhci: Doorbell: 0x00030000 | TCN: 0x00000000 [ 139.946518] mmc2: cqhci: Dev queue: 0x00010000 | Dev Pend: 0x00010000 [ 139.952967] mmc2: cqhci: Task clr: 0x00000000 | SSC1: 0x00011000 [ 139.959411] mmc2: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000 [ 139.965857] mmc2: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000 [ 139.972308] mmc2: cqhci: Resp idx: 0x0000002e | Resp arg: 0x00000900 [ 139.978761] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== [ 139.985214] mmc2: sdhci: Sys addr: 0xb2c19000 | Version: 0x00000002 [ 139.991669] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000400 [ 139.998127] mmc2: sdhci: Argument: 0x40110400 | Trn mode: 0x00000033 [ 140.004618] mmc2: sdhci: Present: 0x01088a8f | Host ctl: 0x00000030 [ 140.011113] mmc2: sdhci: Power: 0x00000002 | Blk gap: 0x00000080 [ 140.017583] mmc2: sdhci: Wake-up: 0x00000008 | Clock: 0x0000000f [ 140.024039] mmc2: sdhci: Timeout: 0x0000008f | Int stat: 0x00000000 [ 140.030497] mmc2: sdhci: Int enab: 0x107f4000 | Sig enab: 0x107f4000 [ 140.036972] mmc2: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000502 [ 140.043426] mmc2: sdhci: Caps: 0x07eb0000 | Caps_1: 0x8000b407 [ 140.049867] mmc2: sdhci: Cmd: 0x00002c1a | Max curr: 0x00ffffff [ 140.056314] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0xffffffff [ 140.062755] mmc2: sdhci: Resp[2]: 0x328f5903 | Resp[3]: 0x00d00f00 [ 140.069195] mmc2: sdhci: Host ctl2: 0x00000008 [ 140.073640] mmc2: sdhci: ADMA Err: 0x00000007 | ADMA Ptr: 0x7809c108 [ 140.080079] mmc2: sdhci: ============================================ [ 140.086662] mmc2: running CQE recovery Fixes: 18094430d6b5 ("mmc: sdhci-esdhc-imx: add ADMA Length Mismatch errata fix") Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-28mmc: sdhci-esdhc-imx: clear the HALT bit when enable CQEBOUGH CHEN1-0/+13
After system suspend, CQE is in cqhci_off state, which set the HALT bit, make CQE in HALT state. If the SoC do not power down the USDHC module, then when system resume back, this bit keep the same, still set. Though there is a sdhci reset during sdhci_resume_host(), but this reset do not impact the CQE part, so need to clear this bit when enable CQE, otherwise CQE will stuck in the first CMDQ request after system resume back. Find this issue on NXP i.MX845s-mek board [ 105.919862] mmc2: cqhci: timeout for tag 6 [ 105.923965] mmc2: cqhci: ============ CQHCI REGISTER DUMP =========== [ 105.930407] mmc2: cqhci: Caps: 0x0000310a | Version: 0x00000510 [ 105.936847] mmc2: cqhci: Config: 0x00001001 | Control: 0x00000001 [ 105.943286] mmc2: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006 [ 105.949725] mmc2: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000 [ 105.956164] mmc2: cqhci: TDL base: 0x7809b000 | TDL up32: 0x00000000 [ 105.962604] mmc2: cqhci: Doorbell: 0x00000040 | TCN: 0x00000000 [ 105.969043] mmc2: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000 [ 105.975483] mmc2: cqhci: Task clr: 0x00000000 | SSC1: 0x00011000 [ 105.981922] mmc2: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000 [ 105.988362] mmc2: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000 [ 105.994801] mmc2: cqhci: Resp idx: 0x00000000 | Resp arg: 0x00000000 [ 106.001240] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== [ 106.007680] mmc2: sdhci: Sys addr: 0xb2b37800 | Version: 0x00000002 [ 106.014120] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000001 [ 106.020560] mmc2: sdhci: Argument: 0x00010000 | Trn mode: 0x00000013 [ 106.026999] mmc2: sdhci: Present: 0x01f88008 | Host ctl: 0x00000030 [ 106.033439] mmc2: sdhci: Power: 0x00000002 | Blk gap: 0x00000080 [ 106.039878] mmc2: sdhci: Wake-up: 0x00000008 | Clock: 0x0000000f [ 106.046318] mmc2: sdhci: Timeout: 0x0000008f | Int stat: 0x00000000 [ 106.052757] mmc2: sdhci: Int enab: 0x107f4000 | Sig enab: 0x107f4000 [ 106.059196] mmc2: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000502 [ 106.065635] mmc2: sdhci: Caps: 0x07eb0000 | Caps_1: 0x8000b407 [ 106.072075] mmc2: sdhci: Cmd: 0x00000d1a | Max curr: 0x00ffffff [ 106.078514] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0x31360181 [ 106.084954] mmc2: sdhci: Resp[2]: 0x44473430 | Resp[3]: 0x00450100 [ 106.091392] mmc2: sdhci: Host ctl2: 0x00000008 [ 106.095836] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x7804b208 [ 106.102274] mmc2: sdhci: ============================================ [ 106.108785] mmc2: running CQE recovery Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: slot-gpio: Remove override_active_level on WPLinus Walleij1-1/+1
The argument "override_active_level" made it possible to enforce a specific polarity on the write-protect GPIO line. All callers in the kernel pass "false" to this call after I have converted all drivers to use GPIO machine descriptors, so remove the argument and clean out this. This kind of polarity inversion should be handled by the GPIO descriptor inside the GPIO library if needed. This rids us of one instance of the kludgy calls into the gpiod_get_raw_value() API. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-esdhc-imx: fix return value check in sdhci_esdhc_imx_probe()Wei Yongjun1-2/+2
In case of error, the function devm_kzalloc() returns NULL pointer not ERR_PTR(). The IS_ERR() test in the return value check should be replaced with NULL test. Fixes: fadac7488064 ("mmc: sdhci-esdhc-imx: add CMDQ support") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-esdhc-imx: add DCMD support for CMDQBOUGH CHEN1-1/+21
Currently, USDHC do not generate transfer complete interrupt when send a non-data-command with R1b response. But if want to support DCMD in CMDQ, need to change this, the DCMD IC logic require the USDHC to enable this function, otherwise DCMD will never get a CC(command complete) interrupt. This patch set ESDHC_VEND_SPEC2_EN_BUSY_IRQ and add DCMD support. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-esdhc-imx: add CMDQ supportBOUGH CHEN1-3/+114
Add CMDQ support for imx8qm/imx8qxp. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> [Ulf: Rebased on top of latest changes] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-esdhc-imx: add HS400_ES support for i.MX8QXPBOUGH CHEN1-0/+29
Add an new esdhc_soc_data for i.MX8QXP, and add HS400_ES mode support. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> [Ulf: Rebased on top of latest changes] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-esdhc-imx: remove the 100MHz limitation for Strobe DLLBOUGH CHEN1-29/+23
For some eMMC, after switch to HS400ES mode, it need to config the strobe dll target dealy even if the clock is 50MHZ or 25MHz, otherwise will meet CMD index/crc error when send CMD13 to check the switch status. [ 2.473915] IRQ status 0x000a8001 [ 2.473934] mmc2: mmc_select_hs400es failed, error -84 [ 2.473938] mmc2: error -84 whilst initialising MMC card Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-esdhc-imx: add delay between tuning cyclesBOUGH CHEN1-0/+2
It's observed that i.MX uSDHC needed delay between tuning cycles for HS200 successful tuning. This patch is to set 1ms delay for that. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-esdhc-imx: add SD clock limitation for imx6ullBOUGH CHEN1-1/+21
i.MX6ULL has errata ERR010450, point out that due to SOC I/O timing limitation, for eMMC HS200 and SD/SDIO 3.0 SDR104, the clock rate can't exceed 150MHz. And for eMMC DDR52 and SD/SDIO DDR50 mode, the clock rate can't exceed 45MHz. This patch add this limit for imx6ull. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> [Ulf: Fixed comments and whitespace] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-esdhc-imx: fix HS400 timing issueBOUGH CHEN1-0/+1
Now tuning reset will be done when the timing is MMC_TIMING_LEGACY/ MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS. But for timing MMC_TIMING_MMC_HS, we can not do tuning reset, otherwise HS400 timing is not right. Here is the process of init HS400, first finish tuning in HS200 mode, then switch to HS mode and 8 bit DDR mode, finally switch to HS400 mode. If we do tuning reset in HS mode, this will cause HS400 mode lost the tuning setting, which will cause CRC error. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Cc: stable@vger.kernel.org # v4.12+ Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: d9370424c948 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci: usdhc: do not do tuning for DDR50 mode.BOUGH CHEN1-0/+20
DDR50 tuning is optinally defined in sd 3.0 spec. And i.MX uSDHC internally already uses a fixed optimized timing for DDR50, normally does not require tuning for DDR50 mode. This patch specify a new execute_tuning function for i.MX uSDHC, do not impact i.MX eSDHC. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-esdhc-imx: clear ESDHC_STD_TUNING_EN for manual tuning methodBOUGH CHEN1-0/+9
The bit ESDHC_STD_TUNING_EN may be configed by bootloader code if it choose to use standard tuning method. So on linux side, if choose to use manual tuning method, need to clear the bit ESDHC_STD_TUNING_EN, remove the impact of bootloader code. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-esdhc-imx: Constify driver dataAndrey Smirnov1-8/+8
Variant specific driver data doesn't change at run-time, so mark it as const to reflect that. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-12-17mmc: sdhci: imx: Use the slot GPIO descriptorLinus Walleij1-6/+8
Simplify things by making the i.MX SDHCI driver just use slot GPIO with descriptors instead of passing around the global GPIO numbers that we want to get rid of. As it turns out, just one single board is using the platform data to pass in GPIOs numbers for CD and WP, so we augment this to use a machine descriptor table instead. Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-12-17mmc: sdhci: Rename SDHCI_ACMD12_ERR and SDHCI_INT_ACMD12ERRAdrian Hunter1-6/+6
The SDHCI_ACMD12_ERR register is used for auto-CMD23 and auto-CMD12 errors, as is the SDHCI_INT_ACMD12ERR interrupt bit. Rename them to SDHCI_AUTO_CMD_STATUS and SDHCI_INT_AUTO_CMD_ERR respectively. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16mmc: sdhci-esdhc-imx: fix indentStefan Agner1-1/+1
Fix indent. This also makes disable/enable clock blocks look alike. Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16mmc: sdhci-esdhc-imx: disable clocks before changing frequencyStefan Agner1-6/+6
In the uSDHC case (e.g. i.MX 6) clocks only get disabled if frequency is set to 0. However, it could be that the stack asks for a frequency change while clocks are on. In that case the function clears the divider registers (by clearing ESDHC_CLOCK_MASK) while the clock is enabled! This causes a short period of time where the clock is undivided (on a i.MX 6DL a clock of 196MHz has been measured). For older IP variants the driver disables clock by clearing some bits in ESDHC_SYSTEM_CONTROL. Make sure to disable card clock before changing frequency for uSDHC IP variants too. Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16mmc: sdhci-esdhc-imx: Switch to SPDX identifierFabio Estevam1-4/+1
Adopt the SPDX license identifier headers to ease license compliance management. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16mmc: sdhci-esdhc-imx: get rid of support_vselStefan Agner1-6/+2
The field support_vsel is currently only used in the device tree case. Get rid of it. No change in behavior. Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16mmc: sdhci-esdhc-imx: support eMMC DDR mode when running at 3.3VStefan Agner1-1/+1
The uSDHC supports DDR modes for eMMC devices running at 3.3V. This allows to run eMMC with 3.3V signaling voltage at DDR52 mode: # cat /sys/kernel/debug/mmc1/ios clock: 52000000 Hz vdd: 21 (3.3 ~ 3.4 V) bus mode: 2 (push-pull) chip select: 0 (don't care) power mode: 2 (on) bus width: 3 (8 bits) timing spec: 8 (mmc DDR52) signal voltage: 0 (3.30 V) driver type: 0 (driver type B) Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-09mmc: sdhci-esdhc-imx: allow 1.8V modes without 100/200MHz pinctrl statesStefan Agner1-12/+9
If pinctrl nodes for 100/200MHz are missing, the controller should not select any mode which need signal frequencies 100MHz or higher. To prevent such speed modes the driver currently uses the quirk flag SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V signaling is required for all faster modes and slower modes use 3.3V signaling only. However, there are eMMC modes which use 1.8V signaling and run below 100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply the stack has no valid mode to use. In this tenuous situation the kernel continuously prints voltage switching errors: mmc1: Switching to 3.3V signalling voltage failed Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by altering the SDHCI capability register. With that the stack is able to select 1.8V modes even if no faster pinctrl states are available: # cat /sys/kernel/debug/mmc1/ios ... timing spec: 8 (mmc DDR52) signal voltage: 1 (1.80 V) ... Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch Signed-off-by: Stefan Agner <stefan@agner.ch> Fixes: ad93220de7da ("mmc: sdhci-esdhc-imx: change pinctrl state according to uhs mode") Cc: <stable@vger.kernel.org> # v4.13+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02mmc: sdhci-esdhc-imx: Set maximum watermark levels for PIO accessAndrew Gabbasov1-0/+22
While performing R/W access in PIO mode, the common SDHCI driver checks the buffer ready status once per whole block processing. That is, after getting an appropriate interrupt, or checking an appropriate status bit, the driver makes buffer accesses for the whole block size (e.g. 128 reads for 512 bytes block). This is done in accordance with SD Host Controller Specification. At the same time, the Ultra Secured Digital Host Controller (uSDHC), used in i.MX6 (and, probably, earlier i.MX series too), uses a separate Watermark Levels register, controlling the amount of data or space available when raising status bit or interrupt. For default watermark setting of 16 words, the controller expects (and guarantees) no more than 16 buffer accesses after raising buffer ready status bit and generating an appropriate interrupt. If the driver tries to access the whole block size, it will get incorrect data at the end, and a new interrupt will appear later, when the driver already doesn't expect it. This happens sometimes, more likely on low frequencies, e.g. when reading EXT_CSD at MMC card initialization phase (which makes that initialization fail). Such behavior of i.MX uSDHC seems to be non-compliant to SDHCI Specification, but this is the way it works now. In order not to rewrite the SDHCI driver PIO mode access logic, the IMX specific driver can just set the watermark level to default block size (128 words or 512 bytes), so that the controller behavior will be consistent to generic specification. This patch does this for PIO mode accesses only, restoring default values for DMA accesses to avoid any possible side effects from performance point of view. Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-01-15Merge branch 'fixes' into nextUlf Hansson1-0/+14
2018-01-15mmc: sdhci-esdhc-imx: Fix i.MX53 eSDHCv3 clockBenoît Thébaudeau1-0/+14
Commit 5143c953a786 ("mmc: sdhci-esdhc-imx: Allow all supported prescaler values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR mode, thus bypassing the SD clock frequency prescaler, in order to be able to get higher SD clock frequencies in some contexts. However, that commit missed the fact that this value is illegal on the eSDHCv3 instance of the i.MX53. This seems to be the only exception on i.MX, this value being legal even for the eSDHCv2 instances of the i.MX53. Fix this issue by changing the minimum prescaler value if the i.MX53 eSDHCv3 is detected. According to the i.MX53 reference manual, if DLLCTRL[10] can be set, then the controller is eSDHCv3, else it is eSDHCv2. This commit fixes the following issue, which was preventing the i.MX53 Loco (IMX53QSB) board from booting Linux 4.15.0-rc5: [ 1.882668] mmcblk1: error -84 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc00 [ 2.002255] mmcblk1: error -84 transferring data, sector 2050, nr 6, cmd response 0x900, card status 0xc00 [ 12.645056] mmc1: Timeout waiting for hardware interrupt. [ 12.650473] mmc1: sdhci: ============ SDHCI REGISTER DUMP =========== [ 12.656921] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001201 [ 12.663366] mmc1: sdhci: Blk size: 0x00000004 | Blk cnt: 0x00000000 [ 12.669813] mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013 [ 12.676258] mmc1: sdhci: Present: 0x01f8028f | Host ctl: 0x00000013 [ 12.682703] mmc1: sdhci: Power: 0x00000002 | Blk gap: 0x00000000 [ 12.689148] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000003f [ 12.695594] mmc1: sdhci: Timeout: 0x0000008e | Int stat: 0x00000000 [ 12.702039] mmc1: sdhci: Int enab: 0x107f004b | Sig enab: 0x107f004b [ 12.708485] mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00001201 [ 12.714930] mmc1: sdhci: Caps: 0x07eb0000 | Caps_1: 0x08100810 [ 12.721375] mmc1: sdhci: Cmd: 0x0000163a | Max curr: 0x00000000 [ 12.727821] mmc1: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x00000000 [ 12.734265] mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 [ 12.740709] mmc1: sdhci: Host ctl2: 0x00000000 [ 12.745157] mmc1: sdhci: ADMA Err: 0x00000001 | ADMA Ptr: 0xc8049200 [ 12.751601] mmc1: sdhci: ============================================ [ 12.758110] print_req_error: I/O error, dev mmcblk1, sector 2050 [ 12.764135] Buffer I/O error on dev mmcblk1p1, logical block 0, lost sync page write [ 12.775163] EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null) [ 12.782746] VFS: Mounted root (ext4 filesystem) on device 179:9. [ 12.789151] mmcblk1: response CRC error sending SET_BLOCK_COUNT command, card status 0x900 Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com> Reported-by: Wladimir J. van der Laan <laanwj@gmail.com> Tested-by: Wladimir J. van der Laan <laanwj@gmail.com> Fixes: 5143c953a786 ("mmc: sdhci-esdhc-imx: Allow all supported prescaler values") Cc: <stable@vger.kernel.org> # v4.13+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-01-09mmc: sdhci-esdhc-imx: Enable/Disable mmc clock during runtime suspendMichael Trimarchi1-0/+4
mmc clock can be stopped during runtime suspend and restart during runtime resume if the sdio irq is not enabled. Stop sdio clock reduce EMI of the device when the bus is not in use. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-01-09mmc: sdhci-esdhc-imx: Changes the order of how clocks are being re-enabledMichael Trimarchi1-7/+9
runtime_resume() should re-enable the clocks in reverse order comparing with runtime_suspend() Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-01-09mmc: sdhci-esdhc-imx: Manage sdhci_runtime_suspend_host error codeMichael Trimarchi1-0/+2
We need to return in case of error even if the actual implementation of sdhci_runtime_suspend_host always return 0. We don't want to power down the clock and the assuption is that the sdhci_runtime_suspend_host always let the system consistent in case of failure Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20mmc: sdhci-esdhc-imx: Remove the ENGcm07207 workaroundBenoît Thébaudeau1-12/+4
The SDHCI_QUIRK_NO_MULTIBLOCK quirk was used as a workaround for the ENGcm07207 erratum. However, it caused excruciatingly slow SD transfers (300 kB/s on average), and this erratum actually does not imply that multiple-block transfers are not supported, so this was overkill. The suggested workaround for this erratum is to set SYSCTL.RSTA, but the simple DAT line software reset (which resets the DMA circuit among others) triggered by sdhci_finish_data() in case of errors seems to be sufficient. Indeed, generating errors in a controlled manner on i.MX25 using the FEVT register right in the middle of read data transfers without this quirk shows that nothing is written to the buffer by the eSDHC past CMD12, and no extra Auto CMD12 is sent with AC12EN set, so the data transfers on AHB are properly aborted. For write data transfers, neither extra data nor extra Auto CMD12 is sent, as expected. Moreover, after intensive stress tests on i.MX25, removing SDHCI_QUIRK_NO_MULTIBLOCK seems to be safe. SDHCI_QUIRK_BROKEN_ADMA has nothing to do with ENGcm07207, so set ESDHC_FLAG_ERR004536 for the devices that had ESDHC_FLAG_ENGCM07207 set in order to continue getting SDHCI_QUIRK_BROKEN_ADMA. Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20mmc: sdhci-esdhc-imx: Allow all supported prescaler valuesBenoît Thébaudeau1-11/+7
On i.MX, SYSCTL.SDCLKFS may always be set to 0 in order to make the SD clock frequency prescaler divide by 1 in SDR mode, even with the eSDHC. The previous minimum prescaler value of 2 in SDR mode with the eSDHC was a code remnant from PowerPC, which actually has this limitation on earlier revisions. In DDR mode, the prescaler can divide by up to 512. The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25, this change makes it possible to get 48 MHz from the USB PLL (240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL (240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2). Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20mmc: sdhci-esdhc-imx: Fix DAT line software resetBenoît Thébaudeau1-21/+38
On i.MX25, the eSDHC DAT line software reset (SYSCTL.RSTD) unexpectedly clears at least the data transfer width (PROCTL.DTW), which then results in data CRC errors. This behavior is not documented, but it has actually been observed. Consequently, the DAT line software resets triggered by sdhci.c in case of errors caused unrecoverable errors. Fix this by making sure that the DAT line software reset does not alter the Host Control register. This behavior being undocumented, it may also be present on other i.MX SoCs, so apply this fix for the whole i.MX family. Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20mmc: sdhci-esdhc-imx: Fix some English mistakes and typosBenoît Thébaudeau1-24/+25
Fix various English mistakes and typos in comments and in printed strings. Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20mmc: sdhci-esdhc-imx: Check the return value from clk_prepare_enable()Fabio Estevam1-13/+41
clk_prepare_enable() may fail, so we should better check its return value and propagate it in the case of error. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc cardHaibo Chen1-0/+26
USDHC tuning circuit should be reset before every time card enumeration or re-enumeration. SD3.0 card need tuning. For SDR104 card, when system suspend in standby mode, and then resume back, the IO timing is still SDR104(tuned) which may result in card re-enumeration fail in low card speed(400khz) for some cards. And we did meet the issue that in certain probability, SDR104 card meet mmc command CRC/Timeout error when send CMD2 during mmc bus resume. This patch reset the tuning circuit when the ios timing is MMC_TIMING_LEGACY/MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS, which means both mmc_power_up() and mmc_power_off() will reset the tuning circuit. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24mmc: sdhci: Let drivers decide whether to use mmc_retune_needed() with pmAdrian Hunter1-0/+6
Devices might save and restore tuning values so that re-tuning might not be needed after a pm transition. Let drivers decide by pushing the mmc_retune_needed() logic down to them. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
2017-04-20mmc: sdhci-esdhc-imx: increase the pad I/O drive strength for DDR50 cardHaibo Chen1-0/+1
Currently for DDR50 card, it need tuning in default. We meet tuning fail issue for DDR50 card and some data CRC error when DDR50 sd card works. This is because the default pad I/O drive strength can't make sure DDR50 card work stable. So increase the pad I/O drive strength for DDR50 card, and use pins_100mhz. This fixes DDR50 card support for IMX since DDR50 tuning was enabled from commit 9faac7b95ea4 ("mmc: sdhci: enable tuning for DDR50") Tested-and-reported-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Cc: stable@vger.kernel.org # v4.4+ Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-13mmc: sdhci-esdhc-imx: Correct two register accessesAaron Brice1-1/+22
- The DMA error interrupt bit is in a different position as compared to the sdhci standard. This is accounted for in many cases, but not handled in the case of clearing the INT_STATUS register by writing a 1 to that location. - The HOST_CONTROL register is very different as compared to the sdhci standard. This is accounted for in the write case, but not when read back out (which it is in the sdhci code). Signed-off-by: Dave Russell <david.russell@datasoft.com> Signed-off-by: Aaron Brice <aaron.brice@datasoft.com> Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-09-26mmc: sdhci-esdhc-imx: correct the max timeout countHaibo Chen1-1/+2
i.MX USDHC Reference Manual has a mistake, for the register SYS_CTRL, the DTOCV(bit 19~16) means the data timeout counter value. When DTOCV is set to 0xF, it means SDCLK << 29, not SDCLK << 28. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-09-26mmc: sdhci-esdhc-imx: do not touch other bit when config DTOCVHaibo Chen1-1/+3
Now, when call esdhc_set_timeout() to set the data timeout counter value, IPP_RST_N(bit 23) is wrongly affected. This patch add a mask to avoid this. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-29mmc: sdhci-esdhc-imx: Use common sdhci_suspend|resume_host()Ulf Hansson1-2/+4
To prepare to make the sdhci_pltfm_suspend|resume() static functions, move sdhci-esdhc-imx over to use the sdhci_suspend|resume_host(). Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
2016-07-29mmc: sdhci-esdhc-imx: Assign system PM ops within #ifdef CONFIG_PM_SLEEPUlf Hansson1-1/+3
The system PM callbacks isn't used unless CONFIG_PM_SLEEP is set, thus it triggers a compiler warning about unused functions. Avoid this by changing from CONFIG_PM to CONFIG_PM_SLEEP. Reported-by: Arnd Bergmann <arnd@arndb.de> Fixes: b70d0b3b5b29 ("mmc: sdhci-esdhc-imx: add esdhc specific suspend resume callback") Cc: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
2016-07-25mmc: sdhci-esdhc-imx: clear tuning bits during driver probeDong Aisheng1-0/+5
The tuning bits like FBCLK_SEL, SMP_CLK_SEL and DLY_CELL which affects timing may have already been set by ROM if booting from SD3.0 mode like SDR104. Let's clear it first during driver probe before doing the new card enumeration to avoid working on the wrong timing. Note that tuning bits are dynamical settings which may need to be kept during MMC_PM_KEEP_POWER suspend, so we did not put them into hwinit function. Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25mmc: sdhci-esdhci-imx: re-initialize hw state after resumeDong Aisheng1-5/+2
sdhci_esdhc_imx_hwinit() includes all basic hw intialization. Calling it after resume to re-initialize hw in case its state is already lost in low power mode. Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25mmc: sdhci-esdhc-imx: move tuning static configuration into hwinit functionDong Aisheng1-18/+18
Move tuning static configuration into basic hwinit function. Tuning configuration may also be lost in low power mode, so need restore in hwinit(). Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25mmc: sdhci-esdhc-imx: factor out hw related initialization into functionDong Aisheng1-32/+40
Move all hw related static initializations into a separate function which helps concentrate the hw related initialization code. And that function could also be called by other places later as a basic hw state restore. e.g. suspend/resume where the hw state is possible to lost due to low power mode. Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25mmc: sdhci-esdhc-imx: fix strobe DLL lock wrong clock issueDong Aisheng1-0/+7
When enable DDR, the clock factor definition is changed. e.g. original 200Mhz will become 100Mhz once MIX_CTRL_DDREN bit is set So we need to update the clock setting then the strobe dll can lock the correct clock rate. Additionally we also need disable the clock before locking strobe dll. Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-08-25 14:58:14 +0000