| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for the asynchronous SDIO wakeup interrupts
- Skip redundant evaluation of eMMC HS400 caps when no-MMC-cap
- Add support to store error stats from host drivers
- Extend debugfs to show error stats from host drivers
- Add single I/O read support in the recovery path for 4k sector cards
MMC host:
- dw_mmc-exynos: Convert corresponding DT bindings to the dtschema
- dw_mmc-rockchip: Add support for the Rockchip RV1126 variant
- mmc_spi: Convert corresponding DT bindings to the dtschema
- mtk-sd: Extend support for interrupts/pinctrls for SDIO low-power mode
- mtk-sd: Add support for SDIO wake irqs
- mtk-sd: Add support for the Mediatek MT8188 variant
- renesas_sdhi: Drop redundant manual tap correction for newer SoCs
- renesas_sdhi: Add support for the R-Car S4-8 and generic Gen4 variants
- sdhci/cqhci: Add support to capture stats from host errors
- sdhci-brcmstb: Add ability to increase max clock rate for SDIO on 72116b0
- sdhci-msm: Add support for the MSM8998 and SM8450 variant
- sdhci-of-at91: Fixup UHS-I mode by rewriting of MC1R
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-of-dwcmshc: Enable reset support for the Rockchip variants
- sdhci-pci-gli: Improve I/O read/write performance for GL9763E
- sdhci-s3c: Convert corresponding DT bindings to the dtschema
- tmio: Avoid glitches when resetting
MEMSTICK core:
- A couple of minor fixes and cleanups"
* tag 'mmc-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (61 commits)
mmc: mediatek: add support for SDIO eint wakup IRQ
mmc: core: Add support for SDIO wakeup interrupt
dt-bindings: mmc: mtk-sd: extend interrupts and pinctrls properties
dt-bindings: mmc: rockchip-dw-mshc: Document Rockchip RV1126
mmc: renesas_sdhi: newer SoCs don't need manual tap correction
mmc: cavium-thunderx: Add of_node_put() when breaking out of loop
mmc: cavium-octeon: Add of_node_put() when breaking out of loop
mmc: core: quirks: Add of_node_put() when breaking out of loop
mmc: sdhci-brcmstb: use clk_get_rate(base_clk) in PM resume
dt-bindings: mmc: sdhci-msm: Document the SM8450 compatible
mmc: sdhci-msm: drop redundant of_device_id entries
dt-bindings: mmc: sdhci-msm: add MSM8998
mmc: block: Add single read for 4k sector cards
mmc: mxcmmc: Use mmc_card_sdio macro
mmc: core: Use mmc_card_* macro and add a new for the sd_combo type
dt-bindings: mmc: sdhci-msm: constrain reg-names per variants
dt-bindings: mmc: sdhci-msm: fix reg-names entries
dt-bindings: mmc: Add compatible for MediaTek MT8188
dt-bindings: mmc: sdhci-msm: document resets
mmc: sdhci-of-at91: fix set_uhs_signaling rewriting of MC1R
...
|
|
If wakeup-source flag is set in host dts node, parse EAI information
from SDIO CCCR interrupt externsion segment for in-band wakeup. If
async interrupt is supported by SDIO card then enable it and set
enable_async_irq flag in sdio_cccr structure to 1. The parse flow is
implemented in sdio_read_cccr().
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-3-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In mmc_fixup_of_compatible_match(), we should call of_node_put()
when breaking out of for_each_child_of_node() which will increase
and decrease the refcount during one iteration.
Fixes: b360b1102670 ("mmc: core: allow to match the device tree to apply quirks")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220719091051.1210806-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In case of adding disk failure, the disk needs to be released, otherwise
disk/queue is leaked.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220718160851.312972-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Cards with 4k native sector size may only be read 4k-aligned,
accommodate for this in the single read recovery and use it.
Fixes: 81196976ed946 (mmc: block: Add blk-mq support)
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/cf4f316274c5474586d0d99b17db4a4c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add mmc_card_sd_combo() macro for sd combo type card and use the mmc_card_*
macro to simplify code instead of comparing card->type.
Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20220713033635.28432-2-sh043.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SD_ROCR_S18A is already defined and is used to check the rocr value, so
let's replace with already defined values for readability.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220706004840.24812-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If 'no-mmc' is set but 'no-mmc-hs400' is not, this warning is raised.
Specifying 'no-mmc' should be enough though.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220614113905.1458715-1-alexander.stein@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When using single_open() for opening, single_release() should be
used instead of seq_release(), otherwise there is a memory leak.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220608090152.179395-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add debug fs entry error state to query eMMC and SD card errors statistics.
If any errors occurred in eMMC and SD card driver level then
err_state value will be set to 1.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-5-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add debug fs entry to query eMMC and SD card errors statistics
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-4-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add changes to capture eMMC and SD card errors.
This is useful for debug and testing.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Ram Prakash Gupta <quic_rampraka@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-2-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
With new API blk_mq_is_reserved_rq() we can tell if a request is from
the reserved pool, so stop passing 'reserved' arg. There is actually
only a single user of that arg for all the callback implementations, which
can use blk_mq_is_reserved_rq() instead.
This will also allow us to stop passing the same 'reserved' around the
blk-mq iter functions next.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/1657109034-206040-4-git-send-email-john.garry@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Set the queue dying flag and call blk_mq_exit_queue from del_gendisk for
all disks that do not have separately allocated queues, and thus remove
the need to call blk_cleanup_queue for them.
Rename blk_cleanup_disk to blk_mq_destroy_queue to make it clear that
this function is intended only for separately allocated blk-mq queues.
This saves an extra queue freeze for devices without a separately
allocated queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20220619060552.1850436-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The intention of the use of mmc_blk_reset_success() in
mmc_blk_cqe_recovery() was to prevent repeated resets when retrying and
getting the same error. However, that may not be the case - any amount
of time and I/O may pass before another recovery is needed, in which
case there would be no reason to deny it the opportunity to recover via
a reset if necessary. CQE recovery is expected seldom and failure to
recover (if the clear tasks command fails), even more seldom, so it is
better to allow the reset always, which can be done by calling
mmc_blk_reset_success() always.
Fixes: 1e8e55b67030c6 ("mmc: block: Add CQE support")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220531171922.76080-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Support zero-out using TRIM for eMMC
- Allow to override the busy-timeout for the ioctl-cmds
MMC host:
- Continued the conversion of DT bindings into the JSON schema
- jz4740: Apply DMA engine limits to maximum segment size
- mmci_stm32: Use a buffer for unaligned DMA requests
- mmc_spi: Enabled high-speed modes via parsing of DT
- omap: Make clock management to be compliant with CCF
- renesas_sdhi:
- Support eMMC HS400 mode for R-Car V3H ES2.0
- Don't allow support for eMMC HS400 for R-Car V3M/D3
- sdhci_am654: Fix problem when SD card slot lacks the card detect
line
- sdhci-esdhc-imx: Add support for the imx8dxl variant
- sdhci-brcmstb: Enable support for clock gating to save power
- sdhci-msm:
- Add support for the sdx65 variant
- Add support for the sm8150 variant
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-pci-gli: Add workaround to allow GL9755 to enter ASPM L1.2"
* tag 'mmc-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: sdhci-of-arasan: Add NULL check for data field
mmc: core: Support zeroout using TRIM for eMMC
mmc: sdhci-brcmstb: Fix compiler warning
mmc: sdhci-msm: Add compatible string check for sdx65
dt-bindings: mmc: sdhci-msm: Document the SDX65 compatible
mmc: sdhci-msm: Add compatible string check for sm8150
dt-bindings: mmc: sdhci-msm: Add compatible string for sm8150
mmc: sdhci-msm: Add SoC specific compatibles
dt-bindings: mmc: sdhci-msm: Convert bindings to yaml
dt-bindings: mmc: brcm,sdhci-brcmstb: cleanup example
dt-bindings: mmc: brcm,sdhci-brcmstb: correct number of reg entries
mmc: sdhci-brcmstb: Enable Clock Gating to save power
mmc: sdhci-brcmstb: Re-organize flags
mmc: mmci: Remove custom ios handler
mmc: atmel-mci: Simplify if(chan) and if(!chan)
mmc: core: use kobj_to_dev()
dt-bindings: mmc: sdhci-of-dwcmhsc: Add rk3588
mmc: core: Add CIDs for cards to the entropy pool
mmc: core: Allows to override the timeout value for ioctl() path
mmc: sdhci-omap: Use of_device_get_match_data() helper
...
|
|
Pull block updates from Jens Axboe:
"Here are the core block changes for 5.19. This contains:
- blk-throttle accounting fix (Laibin)
- Series removing redundant assignments (Michal)
- Expose bio cache via the bio_set, so that DM can use it (Mike)
- Finish off the bio allocation interface cleanups by dealing with
the weirdest member of the family. bio_kmalloc combines a kmalloc
for the bio and bio_vecs with a hidden bio_init call and magic
cleanup semantics (Christoph)
- Clean up the block layer API so that APIs consumed by file systems
are (almost) only struct block_device based, so that file systems
don't have to poke into block layer internals like the
request_queue (Christoph)
- Clean up the blk_execute_rq* API (Christoph)
- Clean up various lose end in the blk-cgroup code to make it easier
to follow in preparation of reworking the blkcg assignment for bios
(Christoph)
- Fix use-after-free issues in BFQ when processes with merged queues
get moved to different cgroups (Jan)
- BFQ fixes (Jan)
- Various fixes and cleanups (Bart, Chengming, Fanjun, Julia, Ming,
Wolfgang, me)"
* tag 'for-5.19/block-2022-05-22' of git://git.kernel.dk/linux-block: (83 commits)
blk-mq: fix typo in comment
bfq: Remove bfq_requeue_request_body()
bfq: Remove superfluous conversion from RQ_BIC()
bfq: Allow current waker to defend against a tentative one
bfq: Relax waker detection for shared queues
blk-cgroup: delete rcu_read_lock_held() WARN_ON_ONCE()
blk-throttle: Set BIO_THROTTLED when bio has been throttled
blk-cgroup: Remove unnecessary rcu_read_lock/unlock()
blk-cgroup: always terminate io.stat lines
block, bfq: make bfq_has_work() more accurate
block, bfq: protect 'bfqd->queued' by 'bfqd->lock'
block: cleanup the VM accounting in submit_bio
block: Fix the bio.bi_opf comment
block: reorder the REQ_ flags
blk-iocost: combine local_stat and desc_stat to stat
block: improve the error message from bio_check_eod
block: allow passing a NULL bdev to bio_alloc_clone/bio_init_clone
block: remove superfluous calls to blkcg_bio_issue_init
kthread: unexport kthread_blkcg
blk-cgroup: cleanup blkcg_maybe_throttle_current
...
|
|
It turned out that polling period for MMC_SEND_OP_COND, that currently is
set to 1ms, still isn't sufficient. In particular a Micron eMMC on a
Beaglebone platform, is reported to sometimes fail to initialize.
Additional test, shows that extending the period to 4ms is working fine, so
let's make that change.
Reported-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Tested-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Fixes: 1760fdb6fe9f (mmc: core: Restore (almost) the busy polling for MMC_SEND_OP_COND")
Fixes: 76bfc7ccc2fa ("mmc: core: adjust polling interval for CMD1")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220517101046.27512-1-ulf.hansson@linaro.org
|
|
If an eMMC card supports TRIM and indicates that it erases to zeros, we can
use it to support hardware offloading of REQ_OP_WRITE_ZEROES, so let's add
support for this.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Link: https://lore.kernel.org/r/20220429152118.3617303-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use kobj_to_dev() instead of open-coding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220425105339.3515368-1-chi.minghao@zte.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
To make the entropy pool a bit better we can toss in the
CID for eMMC and SD cards into it, usually the serial
number portion is at least unique.
This does not count as improvement of the entropy but
in practice it makes it a bit more random to mix in these
numbers.
Cc: Theodore Ts'o <tytso@mit.edu>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220425205442.1347837-1-linus.walleij@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Occasionally, user-land applications initiate longer timeout values for certain commands
through ioctl() system call. But so far we are still using a fixed timeout of 10 seconds
in mmc_poll_for_busy() on the ioctl() path, even if a custom timeout is specified in the
userspace application. This patch allows custom timeout values to override this default
timeout values on the ioctl path.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220423221623.1074556-3-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
|
|
To make it unambiguous that the hw_reset callback is for cards and not
for controllers, we add 'card' to the callback name and convert all
users in one go. We keep the argument as mmc_host, though, because the
callback is used very early when mmc_card is not yet populated.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220408080045.6497-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
To make it unambiguous that mmc_sw_reset() is for cards and not for
controllers, we make the function argument mmc_card instead of mmc_host.
There are no users to convert currently.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220408080045.6497-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Despite mmc_ioc_multi_cmd::num_of_cmds is a 64-bit field, its maximum
value is limited to MMC_IOC_MAX_CMDS (only 255); using a 64-bit local
variable to hold a copy of that field leads to gcc generating ineffective
loop code: despite the source code using an *int* variable for the loop
counters, the 32-bit object code uses 64-bit unsigned counters. Also,
gcc has to drop the most significant word of that 64-bit variable when
calling kcalloc() and assigning to mmc_queue_req::ioc_count anyway.
Using the *unsigned int* variable instead results in a better code.
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/eea3b0bd-6091-f005-7189-b5b7868abdb6@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Way back in commit 4f25580fb84d ("mmc: core: changes frequency to
hs_max_dtr when selecting hs400es"), Rockchip engineers noticed that
some eMMC don't respond to SEND_STATUS commands very reliably if they're
still running at a low initial frequency. As mentioned in that commit,
JESD84-B51 P49 suggests a sequence in which the host:
1. sets HS_TIMING
2. bumps the clock ("<= 52 MHz")
3. sends further commands
It doesn't exactly require that we don't use a lower-than-52MHz
frequency, but in practice, these eMMC don't like it.
The aforementioned commit tried to get that right for HS400ES, although
it's unclear whether this ever truly worked as committed into mainline,
as other changes/refactoring adjusted the sequence in conflicting ways:
08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode
switch")
53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode
for mmc")
In any case, today we do step 3 before step 2. Let's fix that, and also
apply the same logic to HS200/400, where this eMMC has problems too.
Resolves errors like this seen when booting some RK3399 Gru/Scarlet
systems:
[ 2.058881] mmc1: CQHCI version 5.10
[ 2.097545] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
[ 2.209804] mmc1: mmc_select_hs400es failed, error -84
[ 2.215597] mmc1: error -84 whilst initialising MMC card
[ 2.417514] mmc1: mmc_select_hs400es failed, error -110
[ 2.423373] mmc1: error -110 whilst initialising MMC card
[ 2.605052] mmc1: mmc_select_hs400es failed, error -110
[ 2.617944] mmc1: error -110 whilst initialising MMC card
[ 2.835884] mmc1: mmc_select_hs400es failed, error -110
[ 2.841751] mmc1: error -110 whilst initialising MMC card
Ealier versions of this patch bumped to 200MHz/HS200 speeds too early,
which caused issues on, e.g., qcom-msm8974-fairphone-fp2. (Thanks for
the report Luca!) After a second look, it appears that aligns with
JESD84 / page 45 / table 28, so we need to keep to lower (HS / 52 MHz)
rates first.
Fixes: 08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode switch")
Fixes: 53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc")
Fixes: 4f25580fb84d ("mmc: core: changes frequency to hs_max_dtr when selecting hs400es")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/linux-mmc/11962455.O9o76ZdvQC@g550jk/
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220422100824.v4.1.I484f4ee35609f78b932bd50feed639c29e64997e@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Secure erase is a very different operation from discard in that it is
a data integrity operation vs hint. Fully split the limits and helper
infrastructure to make the separation more clear.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> [drbd]
Acked-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> [nifs2]
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org> [f2fs]
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Acked-by: Chao Yu <chao@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220415045258.199825-27-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Just use a non-zero max_discard_sectors as an indicator for discard
support, similar to what is done for write zeroes.
The only places where needs special attention is the RAID5 driver,
which must clear discard support for security reasons by default,
even if the default stacking rules would allow for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> [drbd]
Acked-by: Jan Höppner <hoeppner@linux.ibm.com> [s390]
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220415045258.199825-25-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
To make it unambiguous that mmc_hw_reset() is for cards and not for
controllers, we make the function argument mmc_card instead of mmc_host.
Also, all users are converted.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408080045.6497-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
During the card initialization process, the mmc core checks whether the
eMMC/SD card supports an internal writeback-cache and then enables it
inside the card.
Unfortunately, this isn't according to what the mmc core reports to the
upper block layer. Instead, the writeback-cache support with REQ_FLUSH and
REQ_FUA, are being enabled depending on whether the host supports the CMD23
(MMC_CAP_CMD23) and whether an eMMC supports the reliable-write command.
This is wrong and it may also sound awkward. In fact, it's a remnant
from when both eMMC/SD cards didn't have dedicated commands/support to
control the internal writeback-cache. In other words, it was the best we
could do at that point in time.
To fix the problem, but also without breaking backwards compatibility,
let's align the REQ_FLUSH support with whether the writeback-cache became
successfully enabled - for both eMMC and SD cards.
Cc: stable@kernel.org
Fixes: 881d1c25f765 ("mmc: core: Add cache control for eMMC4.5 device")
Fixes: 130206a615a9 ("mmc: core: Add support for cache ctrl for SD cards")
Depends-on: 97fce126e279 ("mmc: block: Issue a cache flush only when it's enabled")
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Michael Wu <michael@allwinnertech.com>
Link: https://lore.kernel.org/r/20220331073223.106415-1-michael@allwinnertech.com
[Ulf: Re-wrote the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Introduce a SEND_STATUS check for writes through SPI to not mark
an unsuccessful write as successful.
Since SPI SD/MMC does not have states, after a write, the card will
just hold the line LOW until it is ready again. The driver marks the
write therefore as completed as soon as it reads something other than
all zeroes.
The driver does not distinguish from a card no longer signalling busy
and it being disconnected (and the line being pulled-up by the host).
This lead to writes being marked as successful when disconnecting
a busy card.
Now the card is ensured to be still connected by an additional CMD13,
just like non-SPI is ensured to go back to TRAN state.
While at it and since we already poll for the post-write status anyway,
we might as well check for SPIs error bits (any of them).
The disconnecting card problem is reproducable for me after continuous
write activity and randomly disconnecting, around every 20-50 tries
on SPI DS for some card.
Fixes: 7213d175e3b6f ("MMC/SD card driver learns SPI")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/76f6f5d2b35543bab3dfe438f268609c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver changes for 5.18-rc1.
Nothing major, some more good cleanups from Jiri and 2 new serial
drivers. Highlights include:
- termbits cleanups
- export symbol cleanups and other core cleanups from Jiri Slaby
- new sunplus and mvebu uart drivers (amazing that people are still
creating new uarts...)
- samsung serial driver cleanups
- ldisc 29 is now "reserved" for experimental/development line
disciplines
- lots of other tiny fixes and cleanups to serial drivers and
bindings
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (104 commits)
vt_ioctl: fix potential spectre v1 in VT_DISALLOCATE
serial: 8250: fix XOFF/XON sending when DMA is used
tty: serial: samsung: Add ARTPEC-8 support
dt-bindings: serial: samsung: Add ARTPEC-8 UART
serial: sc16is7xx: Clear RS485 bits in the shutdown
tty: serial: samsung: simplify getting OF match data
tty: serial: samsung: constify variables and pointers
tty: serial: samsung: constify s3c24xx_serial_drv_data members
tty: serial: samsung: constify UART name
tty: serial: samsung: constify s3c24xx_serial_drv_data
tty: serial: samsung: reduce number of casts
tty: serial: samsung: embed s3c2410_uartcfg in parent structure
tty: serial: samsung: embed s3c24xx_uart_info in parent structure
serial: 8250_tegra: mark acpi_device_id as unused with !ACPI
tty: serial: bcm63xx: use more precise Kconfig symbol
serial: SERIAL_SUNPLUS should depend on ARCH_SUNPLUS
tty: serial: jsm: fix two assignments in if conditions
tty: serial: jsm: remove redundant assignments to variable linestatus
serial: 8250_mtk: make two read-only arrays static const
serial: samsung_tty: do not unlock port->lock for uart_write_wakeup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big set of staging driver updates for 5.18-rc1.
Loads of tiny cleanups for almost all staging drivers in here, nothing
major at all. Highlights include:
- remove the ashmem Android driver. It is long-dead and if there are
any legacy userspace applications still using it, the Android
kernel images will maintain it, the community shouldn't care about
it anymore
- wfx wifi driver major cleanups. Should be ready to merge out of
staging soon, and will coordinate with the wifi maintainers after
-rc1 is out
- major cleanups and unwinding of the layers of the r8188eu driver.
It's amazing just how many unneeded layers of abstraction is in
there, just when we think it's done, another is found...
- lots of tiny coding style cleanups in many other staging drivers.
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (455 commits)
staging: r8188eu: remove unnecessary memset in r8188eu
staging: greybus: introduce pwm_ops::apply
staging: rts5208: Resolve checkpatch.pl issues.
staging: sm750fb: fix naming style
staging: fbtft: Consider type of init sequence values in fbtft_init_display()
staging: fbtft: Constify buf parameter in fbtft_dbg_hex()
staging: mmal-vchiq: clear redundant item named bulk_scratch
mips: dts: ralink: add MT7621 SoC
staging: r8188eu: remove some unused local ieee80211 macros
staging: r8188eu: make rtl8188e_process_phy_info static
staging: r8188eu: remove unused function prototype
staging: r8188eu: remove three unused receive defines
staging: r8188eu: remove unnecessary initializations
staging: rtl8192e: Fix spelling mistake "RESQUEST" -> "REQUEST"
MAINTAINERS: remove the obsolete file entry for staging in ANDROID DRIVERS
staging: r8188eu: proper error handling in rtw_init_drv_sw
staging: r8188eu: call _cancel_timer_ex from _rtw_free_recv_priv
staging: vt6656: Removed unused variable vt3342_vnt_threshold
staging: vt6656: Removed unused variable bb_vga_0
staging: remove ashmem
...
|
|
When mmc_select_hs400es() tries to switch to the HS400 ES mode, it may bail
out early if the host doesn't support an 8-bit buswidth, as it's required
for the HS400 mode.
To improve the situation, let's instead drop the HS400 bits from the
capability field if the 8-bit bus isn't supported. In this way, we allow
the mmc initialization to continue by trying a lower speed mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220303165151.129806-1-ulf.hansson@linaro.org
|
|
Even if the current WARN() notifies the user that something is severely
wrong, we can still end up in a PANIC() when trying to invoke the missing
->enable_sdio_irq() ops. Therefore, let's also return an error code and
prevent the host from being added.
While at it, move the code into a separate function to prepare for
subsequent changes and for further host caps validations.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220303165142.129745-1-ulf.hansson@linaro.org
|
|
In the error path of mmc_select_hs200() we are trying our best to restore
the card/host into a valid state. This makes sense, especially if we
encounter a simple switch error (-EBADMSG). However, rather than then
continue with using the legacy speed mode, let's try the other better speed
modes first. Additionally, let's update the card->mmc_avail_type to avoid
us from trying a broken HS200 mode again.
In an Amlogic S905W based TV box where the switch to HS200 mode fails for
the eMMC, this allows us to use the eMMC in DDR mode in favor of the legacy
mode, which greatly improves the performance.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20220303164522.129583-1-ulf.hansson@linaro.org
|
|
We need the staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
Commit 76bfc7ccc2fa ("mmc: core: adjust polling interval for CMD1"),
significantly decreased the polling period from ~10-12ms into just a couple
of us. The purpose was to decrease the total time spent in the busy polling
loop, but unfortunate it has lead to problems, that causes eMMC cards to
never gets out busy and thus fails to be initialized.
To fix the problem, but also to try to keep some of the new improved
behaviour, let's start by using a polling period of 1-2ms, which then
increases for each loop, according to common polling loop in
__mmc_poll_for_busy().
Reported-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Huijin Park <huijin.park@samsung.com>
Fixes: 76bfc7ccc2fa ("mmc: core: adjust polling interval for CMD1")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/20220304105656.149281-1-ulf.hansson@linaro.org
|
|
Having a generic UART_LCR_WLEN() macro and the tty_get_char_size()
helper, we can remove all those repeated switch-cases in drivers.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224095558.30929-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sprintf() (still used in the MMC core for the sysfs output) is vulnerable
to the buffer overflow. Use the new-fangled sysfs_emit() instead.
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/717729b2-d65b-c72e-9fac-471d28d00b5a@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We need the staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Until now, the SDIO quirks are applied directly from the driver.
However, it is better to apply the quirks before driver probing. So,
this patch relocate the quirks in the MMC framework.
Note that the WF200 has no valid SDIO VID/PID. Therefore, we match DT
rather than on the SDIO VID/PID.
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20220216093112.92469-3-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On reads with MMC_READ_MULTIPLE_BLOCK that fail,
the recovery handler will use MMC_READ_SINGLE_BLOCK for
each of the blocks, up to MMC_READ_SINGLE_RETRIES times each.
The logic for this is fixed to never report unsuccessful reads
as success to the block layer.
On command error with retries remaining, blk_update_request was
called with whatever value error was set last to.
In case it was last set to BLK_STS_OK (default), the read will be
reported as success, even though there was no data read from the device.
This could happen on a CRC mismatch for the response,
a card rejecting the command (e.g. again due to a CRC mismatch).
In case it was last set to BLK_STS_IOERR, the error is reported correctly,
but no retries will be attempted.
Fixes: 81196976ed946c ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/bc706a6ab08c4fe2834ba0c05a804672@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SD card is allowed to signal busy on DAT0 up to 1s after the
CMD49. According to SD spec (version 6.0 section 5.8.1.3) first host
waits until busy of CMD49 is released and only then polls Power
Management Status register up to 1s until the card indicates ready to
power off.
Without waiting for busy before polling status register sometimes card
becomes unresponsive and system fails to suspend:
[ 205.907459] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 206.421274] sunxi-mmc 1c0f000.mmc: data error, sending stop command
[ 206.421321] sunxi-mmc 1c0f000.mmc: send stop command failed
[ 206.421347] mmc0: error -110 reading status reg of PM func
[ 206.421366] PM: dpm_run_callback(): mmc_bus_suspend+0x0/0x74 returns -110
[ 206.421402] mmcblk mmc0:aaaa: PM: failed to suspend async: error -110
[ 206.437064] PM: Some devices failed to suspend, or early wake event detected
Tested with Sandisk Extreme PRO A2 64GB on Allwinner A64 system.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Fixes: 2c5d42769038 ("mmc: core: Add support for Power Off Notification for SD cards")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220115121447.641524-1-andrej.skvortzov@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Pull block updates from Jens Axboe:
- Unify where the struct request handling code is located in the blk-mq
code (Christoph)
- Header cleanups (Christoph)
- Clean up the io_context handling code (Christoph, me)
- Get rid of ->rq_disk in struct request (Christoph)
- Error handling fix for add_disk() (Christoph)
- request allocation cleanusp (Christoph)
- Documentation updates (Eric, Matthew)
- Remove trivial crypto unregister helper (Eric)
- Reduce shared tag overhead (John)
- Reduce poll_stats memory overhead (me)
- Known indirect function call for dio (me)
- Use atomic references for struct request (me)
- Support request list issue for block and NVMe (me)
- Improve queue dispatch pinning (Ming)
- Improve the direct list issue code (Keith)
- BFQ improvements (Jan)
- Direct completion helper and use it in mmc block (Sebastian)
- Use raw spinlock for the blktrace code (Wander)
- fsync error handling fix (Ye)
- Various fixes and cleanups (Lukas, Randy, Yang, Tetsuo, Ming, me)
* tag 'for-5.17/block-2022-01-11' of git://git.kernel.dk/linux-block: (132 commits)
MAINTAINERS: add entries for block layer documentation
docs: block: remove queue-sysfs.rst
docs: sysfs-block: document virt_boundary_mask
docs: sysfs-block: document stable_writes
docs: sysfs-block: fill in missing documentation from queue-sysfs.rst
docs: sysfs-block: add contact for nomerges
docs: sysfs-block: sort alphabetically
docs: sysfs-block: move to stable directory
block: don't protect submit_bio_checks by q_usage_counter
block: fix old-style declaration
nvme-pci: fix queue_rqs list splitting
block: introduce rq_list_move
block: introduce rq_list_for_each_safe macro
block: move rq_list macros to blk-mq.h
block: drop needless assignment in set_task_ioprio()
block: remove unnecessary trailing '\'
bio.h: fix kernel-doc warnings
block: check minor range in device_add_disk()
block: use "unsigned long" for blk_validate_block_size().
block: fix error unwinding in device_add_disk
...
|
|
kfree() and bitmap_free() are the same. But using the later is more
consistent when freeing memory allocated with bitmap_alloc().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/07a8e48db446888bd77f16b88568e80904f52103.1640528089.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Sparse spits out this following warning:
drivers/mmc/core/queue.c:311:21: warning: incorrect type in assignment (different base types)
drivers/mmc/core/queue.c:311:21: expected int ret
drivers/mmc/core/queue.c:311:21: got restricted blk_status_t [usertype]
drivers/mmc/core/queue.c:314:21: warning: incorrect type in assignment (different base types)
drivers/mmc/core/queue.c:314:21: expected int ret
drivers/mmc/core/queue.c:314:21: got restricted blk_status_t [usertype]
drivers/mmc/core/queue.c:336:16: warning: incorrect type in return expression (different base types)
drivers/mmc/core/queue.c:336:16: expected restricted blk_status_t
drivers/mmc/core/queue.c:336:16: got int [assigned] ret
ret is only used for blk_status_t types, so make it that type.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211215011336.194089-1-joel@jms.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
|
