Age | Commit message (Collapse) | Author | Files | Lines |
|
Make it a bit more obvious that the card has been claimed by the
mmc_test driver so that people don't have to wonder why their block
device never shows up.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Support highmem pages in the bounce buffer code by using the
sg_copy_from/to_buffer() functions.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Add tests that make sure the driver properly checks the blocks and
blksz fields and doesn't assume the sg list has a size that perfectly
matches the current request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Add a couple of tests to make sure the host driver handles highmem
memory pages properly. Unfortunately there is no way to guarantee an
allocation below 4 GB in i386, so it might give you addresses that
are out of reach for the hardware (OTOH, so will any other highmem
allocation in the kernel).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This is a consequence of patch 9ea761bfef52c116fed4715d4043392c2503fe6a.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Relax requirements on host controllers and only require that they do not
report a transfer count than is larger than the actual one (i.e. a lower
value is okay). This is how many other parts of the kernel behaves so
upper layers should already be prepared to handle that scenario. This
gives us a performance boost on MMC cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Clean up and reorganise the mmc_test driver so that it (hopefully)
is easier to extend with more complex tests.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Many failures are non-permanent, but the card might need some time to
finish what it is doing before becoming responsive again. Make sure we
wait for it to finish programming before dealing with the error.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
We can only perform the tests on MMC and SD cards, so avoid binding
to any other type.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Add the ability to run just a single test case by writing the test
case number into the sysfs "test" file.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Fairly simple. "dev_use" was being allocated as a zero length array
because of bad math on 64-bit systems, causing a crash in
find_first_zero_bit(). One-liner follows:
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A dummy driver that performs a series of requests that are often mis-
handled by host drivers.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch converts mmc to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
This also fixes a sparse warning about different signedness.
Only compile tested, because i do not have the hardware.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
mmc_init_queue only initializes the scatterlists with sg_init_table()
when using a bounce buffer. This leads to a BUG() when CONFIG_DEBUG_SG
is set.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Move the code which marks the minor number as free to mmc_blk_put() so
that it happens on the final close() (or removal), instead of doing it
at removal even when the device is still logically open.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Some cards have been reported to signal that they're ready prematurely.
Checking both the busy bit and card state solves the issue.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Commit 45711f1a ("[SG] Update drivers to use sg helpers") had the
following bogus change in drivers/mmc/card/queue.c:
> - src_buf = page_address(src->page) + src->offset;
> + src_buf = sg_virt(dst);
(Notice that "src" is converted to "dst"). Turn this "dst" back into
the intended "src".
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Otherwise we could have junk in the sg fields, fooling
the sg chaining into thinking ->page is valid.
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Teaching the MMC/SD block card driver about SPI.
- Provide the SPI response type flags with each request issued.
- Understand that multiblock SPI writes don't use STOP_TRANSMISSION.
- Correct check for APP_CMD failure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
In a few places, sdio_uart_irq() is called directly instead of waiting
for the actual interrupt to be raised and the SDIO IRQ thread scheduled
in order to reduce latency. However, some interaction with the tty core
may end up calling us back (serial echo, flow control, etc.) creating
two issues:
- the host lock gets claimed twice from the same thread causing a
deadlock;
- the same direct calls to sdio_uart_irq() may be performed causing
unexpected reentrancy into the IRQ handler.
This patch handles both of those issues.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Note that the default baudrate is 4800 instead of 9600 as a convenience
because that's what GPS devices want which is still the main use for
this driver.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This mimics what the serial_core does. Useful for diagnostics.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This currently only accepts the GPS class since that's all I have for
testing. Tested with a Matsushita GPS and gpsd version 2.34.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The MMC_DATA_MULTI flag never had a proper definition of what it
means, so remove it and let the drivers check the block count in
the request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The write parameter in mmc_set_data_timeout() is redundant as the
data structure contains information about the direction of the
transfer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Convert the MMC layer to use standard error codes and not its own,
incompatible values.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Reorganize the code that initializes mmc_block's bounce buffer in
order to avoid warnings when MMC_BLOCK_BOUNCE isn't used.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
drivers/mmc/core/: make 3 functions static
mmc: add missing printk levels
mmc: remove redundant debug information from sdhci and wbsd
mmc: proper debugging output in core
mmc: be more verbose about card insertions/removal
mmc: Don't hold lock when releasing an added card
mmc: add a might_sleep() to mmc_claim_host()
mmc: update kerneldoc
mmc: update header file paths
sdhci: add support to ENE-CB714
mmc: check error bits before command completion
|
|
Make sure all headers in the files reflect their true position
in the tree.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some hosts cannot do scatter/gather in hardware. Since not doing sg
is such a big performance hit, we (optionally) bounce the requests
to a simple linear buffer that we hand over to the driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Remove dead code and unused structs from the block driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The MMC block devices now have an assigned major. Make sure
we actually use it.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The classic MMC bus was defined as multi card bus
system, which is reflected in the design in the MMC
layer.
When SD showed up, the bus topology was abandoned
and a star topology (one card per host) was mandated.
MMC version 4 has followed this, officially deprecating
the bus topology.
As we do not have any known users of the bus
topology we can remove support for it. This will
simplify the code and rectify some incorrect
assumptions in the newer additions.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Make sure we don't deadlock when removing a suspended block
queue, something that might happen if the card is removed during
suspend.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Clean up the drivers/mmc directory by moving card and host drivers
into subdirectories.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|