Age | Commit message (Collapse) | Author | Files | Lines |
|
This driver enables the LPC snoop hardware on the ASPEED BMC
which generates an interrupt upon every write to an I/O port
by the host.
This is typically used to monitor BIOS boot progress by listening
to well-known debug port 80h.
The functionality in this commit just saves all snooped values
to a circular 2K buffer in the kernel, subsequent commits can
act on the values to do things with them.
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is the following link error with CONFIG_PCI_ENDPOINT_TEST=y and
CONFIG_CRC32=m:
drivers/built-in.o: In function 'pci_endpoint_test_ioctl':
pci_endpoint_test.c:(.text+0xf1251): undefined reference to 'crc32_le'
pci_endpoint_test.c:(.text+0xf1322): undefined reference to 'crc32_le'
pci_endpoint_test.c:(.text+0xf13b2): undefined reference to 'crc32_le'
pci_endpoint_test.c:(.text+0xf141e): undefined reference to 'crc32_le'
Fix this by selecting CRC32 in the PCI_ENDPOINT_TEST kconfig entry.
Fixes: 2c156ac71c6b ("misc: Add host side PCI driver for PCI test function device")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
|
|
Add PCI endpoint test driver that can verify base address register, legacy
interrupt/MSI interrupt and read/write/copy buffers between host and
device. The corresponding pci-epf-test function driver should be used on
the EP side.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
It looks like arm-charlcd.c belongs to auxdisplay subsystem.
Move it to drivers/auxdisplay folder.
No functional changes intended.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It looks like panel.c belongs to auxdisplay subsystem.
Move it to drivers/auxdisplay folder.
No functional changes intended.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Extract the character LCD core from the Parallel port LCD/Keypad Panel
driver in the misc subsystem, and convert it into a subdriver in the
auxdisplay subsystem. This allows the character LCD core to be used by
other drivers later.
Compilation is controlled by its own Kconfig symbol CHARLCD, which is to
be selected by its users, but can be enabled manually for
compile-testing.
All functions changed their prefix from "lcd_" to "charlcd_", and gained
a "struct charlcd *" parameter to operate on a specific instance.
While the driver API thus is ready to support multiple instances, the
current limitation of a single display (/dev/lcd has a single misc minor
assigned) is retained.
No functional changes intended.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to manage server systems, there is typically another processor
known as a BMC (Baseboard Management Controller) which is responsible
for powering the server and other various elements, sometimes fans,
often the system flash.
The Aspeed BMC family which is what is used on OpenPOWER machines and a
number of x86 as well is typically connected to the host via an LPC
(Low Pin Count) bus (among others).
The LPC bus is an ISA bus on steroids. It's generally used by the
BMC chip to provide the host with access to the system flash (via MEM/FW
cycles) that contains the BIOS or other host firmware along with a
number of SuperIO-style IOs (via IO space) such as UARTs, IPMI
controllers.
On the BMC chip side, this is all configured via a bunch of registers
whose content is related to a given policy of what devices are exposed
at a per system level, which is system/vendor specific, so we don't want
to bolt that into the BMC kernel. This started with a need to provide
something nicer than /dev/mem for user space to configure these things.
One important aspect of the configuration is how the MEM/FW space is
exposed to the host (ie, the x86 or POWER). Some registers in that
bridge can define a window remapping all or portion of the LPC MEM/FW
space to a portion of the BMC internal bus, with no specific limits
imposed in HW.
I think it makes sense to ensure that this window is configured by a
kernel driver that can apply some serious sanity checks on what it is
configured to map.
In practice, user space wants to control this by flipping the mapping
between essentially two types of portions of the BMC address space:
- The flash space. This is a region of the BMC MMIO space that
more/less directly maps the system flash (at least for reads, writes
are somewhat more complicated).
- One (or more) reserved area(s) of the BMC physical memory.
The latter is needed for a number of things, such as avoiding letting
the host manipulate the innards of the BMC flash controller via some
evil backdoor, we want to do flash updates by routing the window to a
portion of memory (under control of a mailbox protocol via some
separate set of registers) which the host can use to write new data in
bulk and then request the BMC to flash it. There are other uses, such
as allowing the host to boot from an in-memory flash image rather than
the one in flash (very handy for continuous integration and test, the
BMC can just download new images).
It is important to note that due to the way the Aspeed chip lets the
kernel configure the mapping between host LPC addresses and BMC ram
addresses the offset within the window must be a multiple of size.
Not doing so will fragment the accessible space rather than simply
moving 'zero' upwards. This is caused by the nature of HICR8 being a
mask and the way host LPC addresses are translated.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All 18 suboptions related to the panel driver have individual
dependencies on PANEL.
Replace them by a single "if PANEL / endif # PANEL" section for easier
dependency management.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As of commit 7c5763b8453a9487 ("drivers: misc: Remove MISC_DEVICES
config option"), misc device support no longer needs to be enabled
manually.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When panel driver was moved from staging to misc a new line was missing
to be added on Kconfig file.
Fixes: 305b37bd01c2 ("misc: Move panel driver out of staging")
Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce a new "protect-exec" reserved sram area type which is
makes use of the the existing functionality provided for the "pool"
sram region type for use with the genalloc framework and with the
added requirement that it be maintained as read-only and executable
while allowing for an arbitrary number of drivers to share the space.
This introduces a common way to maintain a region of sram as read-only
and executable and also introduces a helper function, sram_exec_copy,
which allows for copying data to this protected region while maintaining
locking to avoid conflicts between multiple users of the same space. A
region of memory that is marked with the "protect-exec" flag in the
device tree also has the requirement of providing a page aligned block
of memory so that the page attribute manipulation does not affect
surrounding regions.
Also, selectively enable this only for builds that support set_memory_*
calls, for now just ARM, through the use of Kconfig.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the fixes in here for merging and testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patches merged to the IIO BMP085 driver makes it fully compliant
with all features found in this old misc driver. Retire this old
driver in favor of the new one in the proper subsystem.
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Marek Belisko <marek@goldelico.com>
Acked-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Rohm BH1780 ambient light sensor has a new driver with extended
functionality (proper runtime PM) in the appropriate framework IIO,
it can be found at:
drivers/iio/light/bh1780.c
The MISC driver symbol CONFIG_SENSORS_BH1780 does not appear in any
defconfigs, so it should safe to delete.
Cc: Hemanth V <hemanthv@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This resolves the merge issues and confusions people were having with
the goldfish drivers due to changes for them showing up in two different
trees.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 985087dbcb02 'misc: add support for bmp18x chips to the bmp085
driver' changed the BMP085 config symbol to a boolean. I see no
reason why the shared code cannot be built as a module, so change it
back to tristate.
Fixes: 985087dbcb02 ("misc: add support for bmp18x chips to the bmp085 driver")
Cc: Eric Andersson <eric.andersson@unixphere.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow the pch_phub driver to be build on MIPS platforms, in preparation
for its use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move panel driver from drivers/staging/panel to drivers/misc.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix build when CONFIG_SERIAL_8250=m and CONFIG_IBM_ASM=y.
Fixes these build errors:
drivers/built-in.o: In function `ibmasm_remove_one':
module.c:(.text+0xf6874): undefined reference to `ibmasm_unregister_uart'
drivers/built-in.o: In function `ibmasm_init_one':
module.c:(.text+0xf6c37): undefined reference to `ibmasm_register_uart'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Max Asbock <masbock@us.ibm.com>
Cc: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Get notified immediately when a balloon target is set, instead of waiting for
up to one second.
The up-to 1 second gap could be long enough to cause swapping inside of the
VM that receives the VM.
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: Xavier Deguillard <xdeguillard@vmware.com>
Tested-by: Siva Sankar Reddy B <sankars@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver is used to configure the coincell charger found in
Qualcomm PMICs.
The driver allows configuring the current-limiting resistor for
the charger, as well as the voltage to apply to the coincell
(or capacitor) when charging.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CARMA project has ended, and the hardware has all been moved into
storage. It is unlikely to ever be used again.
Remove the drivers so that there is no more maintenance burden from
ongoing upstream kernel changes.
Signed-off-by: Ira W. Snyder <ira.snyder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When removing old board !DT support, several Kconfig options were deleted.
Propagate this removal to drivers Kconfig files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This adds the base cxl support that cannot be built as a module. Specifically
it adds the cxl callbacks that are called from the core powerpc mm code which
must always exist irrespective of if the cxl module is loaded or not. This is
similar to how cell works with CONFIG_SPU_BASE.
This adds a cxl_slbia() call (similar to spu_flush_all_slbs()) which checks if
the cxl module is loaded and in use, returning immediately if it is not. If it
is in use it calls into the cxl SLB invalidation code.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The misc/atmel_pwm is not used by any mainlined boards and has been replaced by
the pwm-driver using the generic PWM framework.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
AT91 symbols AT91SAM9263, AT91SAM9RL, and AT91SAM9G45 do not exist and this
patch changes them to their correct ARCH_* version.
These symbols are chosen instead of the SOC_* ones because this driver is not
converted to DT.
Anyway, the ATMEL_PWM symbol and the associated driver will be removed soon,
during the move to the PWM sub-system.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into next
Pull char/misc driver patches from Greg KH:
"Here is the big char / misc driver update for 3.16-rc1.
Lots of different driver updates for a variety of different drivers
and minor driver subsystems.
All have been in linux-next with no reported issues"
* tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (79 commits)
hv: use correct order when freeing monitor_pages
spmi: of: fixup generic SPMI devicetree binding example
applicom: dereferencing NULL on error path
misc: genwqe: fix uninitialized return value in genwqe_free_sync_sgl()
miscdevice.h: Simple syntax fix to make pointers consistent.
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
mcb: Add support for shared PCI IRQs
drivers: Remove duplicate conditionally included subdirs
misc: atmel_pwm: only build for supported platforms
mei: me: move probe quirk to cfg structure
mei: add per device configuration
mei: me: read H_CSR after asserting reset
mei: me: drop harmful wait optimization
mei: me: fix hw ready reset flow
mei: fix memory leak of mei_clients array
uio: fix vma io range check in mmap
drivers: uio_dmem_genirq: Fix memory leak in uio_dmem_genirq_probe()
w1: do not unlock unheld list_mutex in __w1_remove_master_device()
w1: optional bundling of netlink kernel replies
connector: allow multiple messages to be sent in one packet
...
|
|
There is architecture code in mach-at91 that depends on the
CONFIG_ATMEL_PWM symbol in order to call the soc-specific
at91_add_device_pwm function. While all of this is about code
that will be removed in the future, using DT probing and
the PWM framework, we currently get a build failure:
arch/arm/mach-at91/built-in.o: In function `at91_pwm_leds':
arch/arm/mach-at91/leds.c:88: undefined reference to `at91_add_device_pwm'
This patch ensures we only try to build this driver on
platforms on which it will build and work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pch_phub driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch - finally, after over 6 months! :-( - addresses
Samuel's request to split the vexpress-sysreg driver into
smaller portions and define the device in a form of MFD
cells:
* LEDs code has been completely removed and replaced with
"gpio-leds" nodes in the tree (referencing dedicated
GPIO subnodes in sysreg - bindings documentation updated);
this also better fits the reality as some variants of the
motherboard don't have all the LEDs populated
* syscfg bridge code has been extracted into a separate
driver (placed in drivers/misc for no better place)
* all the ID & MISC registers are defined as sysconf
making them available for other drivers should they need
to use them (and also to the user via /sys/kernel/debug/regmap
which can be helpful in platform debugging)
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
|
|
According to the driver descriptions, the atmel_pwm and atmel-ssc
drivers are only useful on Atmel AT32 and AT91 systems. So add
hardware dependencies to these drivers to hide them on other systems.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones
added.
All have been in linux-next for a while"
* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1375 commits)
staging: xillybus: XILLYBUS_PCIE depends on PCI_MSI
staging: xillybus: Added "select CRC32" for XILLYBUS in Kconfig
staging: comedi: poc: remove obsolete driver
staging: unisys: replace kzalloc/kfree with UISMALLOC/UISFREE
staging: octeon-usb: prevent memory corruption
staging: usbip: fix line over 80 characters
staging: usbip: fix quoted string split across lines
Staging: unisys: Remove RETINT macro
Staging: unisys: Remove FAIL macro
Staging: unisys: Remove RETVOID macro
Staging: unisys: Remove RETPTR macro
Staging: unisys: Remove RETBOOL macro
Staging: unisys: Remove FAIL_WPOSTCODE_1 macro
Staging: unisys: Cleanup macros to get rid of goto statements
Staging: unisys: include: Remove unused macros from timskmod.h
staging: dgap: fix the rest of the checkpatch warnings in dgap.c
Staging: bcm: Remove unnecessary parentheses
staging: wlags49_h2: Delete unnecessary braces
staging: wlags49_h2: Do not use assignment in if condition
staging: wlags49_h2: Enclose macro in a do-while loop
...
|
|
The bus and architecture dependencies are already on MFD_CS5535, so
there is no need to repeat them here.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code is clean, there are users of it, so it doesn't belong in
staging anymore, move it to drivers/misc/.
Cc: Steve Underwood <steveu@coppice.org>
Cc: David Rowe <david@rowetel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable possiblity to configure and build this driver.
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Co-authors: Joerg-Stephan Vogt <jsvogt@de.ibm.com>,
Michael Jung <MIJUNG@de.ibm.com>,
Michael Ruettger <michael@ibmra.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Mostly bug fixes and clean up. There is a new driver, which is
actually moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree
support in the pwm-backlight driver. Backlights can now additionally
be powered using a regulator and enabled using a GPIO in addition to
just the PWM input"
* tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
Documentation/pwm: Update supported SoC name for pwm-samsung
pwm: samsung: Fix kernel warning while unexporting a channel
MAINTAINERS: Move PWM subsystem tree to kernel.org
Documentation/pwm: Fix trivial typos
pwm-backlight: Remove unused variable
pwm_backlight: avoid short blank screen while doing hibernation
pwm-backlight: Fix brightness adjustment
pwm: add ep93xx PWM support
pwm-backlight: Allow for non-increasing brightness levels
pwm-backlight: Add power supply support
pwm-backlight: Use new enable_gpio field
unicore32: Initialize PWM backlight enable_gpio field
ARM: shmobile: Initialize PWM backlight enable_gpio field
ARM: SAMSUNG: Initialize PWM backlight enable_gpio field
ARM: pxa: Initialize PWM backlight enable_gpio field
ARM: OMAP: Initialize PWM backlight enable_gpio field
pwm-backlight: Add optional enable GPIO
pwm-backlight: Track enable state
pwm-backlight: Refactor backlight power on/off
pwm-backlight: Improve readability
...
|
|
Remove the non-standard EP93xx PWM driver in drivers/misc and add
a new driver for the PWM controllers on the EP93xx platform based
on the PWM framework.
These PWM controllers each support 1 PWM channel with programmable
duty cycle, frequency, and polarity inversion.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This patch enables the following:
a) Initializes the Intel MIC X100 PCIe devices.
b) Provides sysfs entries for family and stepping information.
Co-author: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Caz Yokoyama <Caz.Yokoyama@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Harshavardhan R Kharche <harshavardhan.r.kharche@intel.com>
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Acked-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the big driver core merge for 3.11-rc1
Lots of little things, and larger firmware subsystem updates, all
described in the shortlog. Nice thing here is that we finally get rid
of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
been always on for a number of kernel releases, now it's just
removed)"
* tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
driver core: device.h: fix doc compilation warnings
firmware loader: fix another compile warning with PM_SLEEP unset
build some drivers only when compile-testing
firmware loader: fix compile warning with PM_SLEEP set
kobject: sanitize argument for format string
sysfs_notify is only possible on file attributes
firmware loader: simplify holding module for request_firmware
firmware loader: don't export cache_firmware and uncache_firmware
drivers/base: Use attribute groups to create sysfs memory files
firmware loader: fix compile warning
firmware loader: fix build failure with !CONFIG_FW_LOADER_USER_HELPER
Documentation: Updated broken link in HOWTO
Finally eradicate CONFIG_HOTPLUG
driver core: firmware loader: kill FW_ACTION_NOHOTPLUG requests before suspend
driver core: firmware loader: don't cache FW_ACTION_NOHOTPLUG firmware
Documentation: Tidy up some drivers/base/core.c kerneldoc content.
platform_device: use a macro instead of platform_driver_register
firmware: move EXPORT_SYMBOL annotations
firmware: Avoid deadlock of usermodehelper lock at shutdown
dell_rbu: Select CONFIG_FW_LOADER_USER_HELPER explicitly
...
|
|
Some drivers can be built on more platforms than they run on. This is
a burden for users and distributors who package a kernel. They have to
manually deselect some (for them useless) drivers when updating their
configs via oldconfig. And yet, sometimes it is even impossible to
disable the drivers without patching the kernel.
Introduce a new config option COMPILE_TEST and make all those drivers
to depend on the platform they run on, or on the COMPILE_TEST option.
Now, when users/distributors choose COMPILE_TEST=n they will not have
the drivers in their allmodconfig setups, but developers still can
compile-test them with COMPILE_TEST=y.
Now the drivers where we use this new option:
* PTP_1588_CLOCK_PCH: The PCH EG20T is only compatible with Intel Atom
processors so it should depend on x86.
* FB_GEODE: Geode is 32-bit only so only enable it for X86_32.
* USB_CHIPIDEA_IMX: The OF_DEVICE dependency will be met on powerpc
systems -- which do not actually support the hardware via that
method.
* INTEL_MID_PTI: It is specific to the Penwell type of Intel Atom
device.
[v2]
* remove EXPERT dependency
[gregkh - remove chipidea portion, as it's incorrect, and also doesn't
apply to my driver-core tree]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-geode@lists.infradead.org
Cc: linux-fbdev@vger.kernel.org
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: netdev@vger.kernel.org
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: "Keller, Jacob E" <jacob.e.keller@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since we have at least one user of this function outside of CONFIG_NET
scope, we have to provide this function independently. The proposed
solution is to move it under lib/net_utils.c with corresponding
configuration variable and select wherever it is needed.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 paravirt update from Ingo Molnar:
"Various paravirtualization related changes - the biggest one makes
guest support optional via CONFIG_HYPERVISOR_GUEST"
* 'x86-paravirt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, wakeup, sleep: Use pvops functions for changing GDT entries
x86, xen, gdt: Remove the pvops variant of store_gdt.
x86-32, gdt: Store/load GDT for ACPI S3 or hibernation/resume path is not needed
x86-64, gdt: Store/load GDT for ACPI S3 or hibernate/resume path is not needed.
x86: Make Linux guest support optional
x86, Kconfig: Move PARAVIRT_DEBUG into the paravirt menu
|
|
This driver requests and remaps a memory region as configured in the
device tree. It serves memory from this region via the genalloc API. It
optionally enables the SRAM clock.
Other drivers can retrieve the genalloc pool from a phandle pointing to
this drivers' device node in the device tree.
The allocation granularity is hard-coded to 32 bytes for now, to make the
SRAM driver useful for the 6502 remoteproc driver. There is overhead for
bigger SRAMs, where only a much coarser allocation granularity is needed:
At 32 bytes minimum allocation size, a 256 KiB SRAM needs a 1 KiB bitmap
to track allocations.
[akpm@linux-foundation.org: fix Kconfig text, make sram_init static]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Huang Shijie <shijie8@gmail.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Matt Porter <mporter@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver was merged in 2.6.38 but never actually compiled because
it depends on the <mach/pcie.h> header that has not made it into the
kernel. Starting with Linux-3.10, this results in "allyesconfig"
build errors, since spear13xx can now be enabled with the default
"multiplatform" platform on ARM. Let's mark it as broken for now.
If it doesn't get fixed, we can drop it completely.
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This module accepts a single 'irq' parameter, which it should register for.
Its sole purpose is to help with debugging of IRQ sharing problems, by
force-enabling IRQ that would otherwise be disabled.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Put all config options needed to run Linux as a guest behind a
CONFIG_HYPERVISOR_GUEST menu so that they don't get built-in by default
but be selectable by the user. Also, make all units which depend on
x86_hyper, depend on this new symbol so that compilation doesn't fail
when CONFIG_HYPERVISOR_GUEST is disabled but those units assume its
presence.
Sort options in the new HYPERVISOR_GUEST menu, adapt config text and
drop redundant select.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1362428421-9244-3-git-send-email-bp@alien8.de
Cc: Dmitry Torokhov <dtor@vmware.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
|