summaryrefslogtreecommitdiffstats
path: root/drivers/memory
AgeCommit message (Collapse)AuthorFilesLines
2019-01-16memory: tegra: Clean up error messagesDmitry Osipenko1-7/+8
Make all messages to start with a lower case and don't unnecessarily go over 80 chars in the code. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2019-01-16memory: tegra: Do not ask for IRQ sharingDmitry Osipenko1-1/+1
Memory Controller driver never shared IRQ with any other driver and very unlikely that it will. Hence there is no need to request IRQ sharing and the corresponding flag can be dropped safely. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2019-01-16memory: tegra: Do not try to probe SMMU on Tegra20Dmitry Osipenko1-2/+4
Tegra20 doesn't have SMMU. Move out checking of the SMMU presence from the SMMU driver into the Memory Controller driver. This change makes code consistent in regards to how GART/SMMU presence checking is performed. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2019-01-16iommu/tegra: gart: Integrate with Memory Controller driverDmitry Osipenko1-0/+43
The device-tree binding has been changed. There is no separate GART device anymore, it is squashed into the Memory Controller. Integrate GART module with the MC in a way it is done for the SMMU on Tegra30+. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2019-01-16memory: tegra: Use relaxed versions of readl/writelDmitry Osipenko1-2/+2
There is no need for inserting of memory barriers to access registers of Memory Controller. Hence use the relaxed versions of the accessors. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2019-01-16memory: tegra: Use of_device_get_match_data()Dmitry Osipenko1-6/+2
There is no need to match device with the DT node since it was already matched, use of_device_get_match_data() helper to get the match-data. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2019-01-16memory: tegra: Read client ID on GART page faultDmitry Osipenko1-2/+10
With the device tree binding changes, now Memory Controller has access to GART registers. Hence it is now possible to read client ID on GART page fault to get information about what memory client causes the fault. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2019-01-16memory: tegra: Adapt to Tegra20 device-tree binding changesDmitry Osipenko2-19/+8
The tegra20-mc device-tree binding has been changed, GART has been squashed into Memory Controller and now the clock property is mandatory for Tegra20, the DT compatible has been changed as well. Adapt driver to the DT changes. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2019-01-16memory: tegra: Don't invoke Tegra30+ specific memory timing setup on Tegra20Dmitry Osipenko1-5/+6
This fixes irrelevant "tegra-mc 7000f000.memory-controller: no memory timings for RAM code 0 registered" warning message during of kernels boot-up on Tegra20. Fixes: a8d502fd3348 ("memory: tegra: Squash tegra20-mc into common tegra-mc driver") Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2019-01-05Merge tag 'armsoc-late' of ↵Linus Torvalds3-0/+473
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull more ARM SoC updates from Olof Johansson: "A few updates that we merged late but are low risk for regressions for other platforms (and a few other straggling patches): - I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in here. They're for a driver for the PL353 SRAM controller and a build fix for the qualcomm scm driver. - A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated Vivante GPU, 256MB RAM, Wifi). This includes some acked platform-specific drivers (serial, etc). This also include DTs for two boards with this SoC, OrangePi 2G and OrangePi i86. - i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K video playback offload). This is the first i.MX 64-bit SoC. - Some minor updates to Samsung boards (adding a few peripherals in DTs). - Small rework for SMP bootup on STi platforms. - A couple of TEE driver fixes. - A couple of new config options (bcm2835 thermal, Uniphier MDMAC) enabled in defconfigs" * tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits) ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC arm64: defconfig: Re-enable bcm2835-thermal driver MAINTAINERS: Add entry for RDA Micro SoC architecture tty: serial: Add RDA8810PL UART driver ARM: dts: rda8810pl: Add interrupt support for UART dt-bindings: serial: Document RDA Micro UART ARM: dts: rda8810pl: Add timer support ARM: dts: Add devicetree for OrangePi i96 board ARM: dts: Add devicetree for OrangePi 2G IoT board ARM: dts: Add devicetree for RDA8810PL SoC ARM: Prepare RDA8810PL SoC dt-bindings: arm: Document RDA8810PL and reference boards dt-bindings: Add RDA Micro vendor prefix ARM: sti: remove pen_release and boot_lock arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards arm64: dts: imx8mq-evk: enable watchdog arm64: dts: imx8mq: add watchdog devices MAINTAINERS: add i.MX8 DT path to i.MX architecture arm64: add support for i.MX8M EVK board arm64: add basic DTS for i.MX8MQ ...
2018-12-31Merge tag 'armsoc-drivers' of ↵Linus Torvalds4-4/+606
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Olof Johansson: "Misc driver updates for platforms, many of them power related. - Rockchip adds power domain support for rk3066 and rk3188 - Amlogic adds a power measurement driver - Allwinner adds SRAM support for three platforms (F1C100, H5, A64 C1) - Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7 - Broadcom fixes suspend/resume with Thumb2 kernels, and improves stability of a handful of firmware/platform interfaces - PXA completes their conversion to dmaengine framework - Renesas does a bunch of PM cleanups across many platforms - Tegra adds support for suspend/resume on T186/T194, which includes some driver cleanups and addition of wake events - Tegra also adds a driver for memory controller (EMC) on Tegra2 - i.MX tweaks power domain bindings, and adds support for i.MX8MQ in GPC - Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60 and misc cleanups across several platforms" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits) ARM: at91: add support in soc driver for new SAM9X60 ARM: at91: add support in soc driver for LPDDR2 SiP memory: omap-gpmc: Use of_node_name_eq for node name comparisons bus: ti-sysc: Check for no-reset and no-idle flags at the child level ARM: OMAP2+: Check also the first dts child for hwmod flags soc: amlogic: meson-clk-measure: Add missing REGMAP_MMIO dependency soc: imx: gpc: Increase GPC_CLK_MAX to 7 soc: renesas: rcar-sysc: Fix power domain control after system resume soc: renesas: rcar-sysc: Merge PM Domain registration and linking soc: renesas: rcar-sysc: Remove rcar_sysc_power_{down,up}() helpers soc: renesas: r8a77990-sysc: Fix initialization order of 3DG-{A,B} dt-bindings: sram: sunxi: Add compatible for the A64 SRAM C1 dt-bindings: sram: sunxi: Add bindings for the H5 with SRAM C1 dt-bindings: sram: Add Allwinner suniv F1C100s soc: sunxi: sram: Add support for the H5 SoC system control soc: sunxi: sram: Enable EMAC clock access for H3 variant soc: imx: gpcv2: add support for i.MX8MQ SoC soc: imx: gpcv2: move register access table to domain data soc: imx: gpcv2: prefix i.MX7 specific defines dmaengine: pxa: make the filter function internal ...
2018-12-29Merge tag 'kbuild-v4.21' of ↵Linus Torvalds1-3/+2
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild updates from Masahiro Yamada: "Kbuild core: - remove unneeded $(call cc-option,...) switches - consolidate Clang compiler flags into CLANG_FLAGS - announce the deprecation of SUBDIRS - fix single target build for external module - simplify the dependencies of 'prepare' stage targets - allow fixdep to directly write to .*.cmd files - simplify dependency generation for CONFIG_TRIM_UNUSED_KSYMS - change if_changed_rule to accept multi-line recipe - move .SECONDARY special target to scripts/Kbuild.include - remove redundant 'set -e' - improve parallel execution for CONFIG_HEADERS_CHECK - misc cleanups Treewide fixes and cleanups - set Clang flags correctly for PowerPC boot images - fix UML build error with CONFIG_GCC_PLUGINS - remove unneeded patterns from .gitignore files - refactor firmware/Makefile - remove unneeded rules for *offsets.s - avoid unneeded regeneration of intermediate .s files - clean up ./Kbuild Modpost: - remove unused -M, -K options - fix false positive warnings about section mismatch - use simple devtable lookup instead of linker magic - misc cleanups Coccinelle: - relax boolinit.cocci checks for overall consistency - fix warning messages of boolinit.cocci Other tools: - improve -dirty check of scripts/setlocalversion - add a tool to generate compile_commands.json from .*.cmd files" * tag 'kbuild-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (51 commits) kbuild: remove unused cmd_gentimeconst kbuild: remove $(obj)/ prefixes in ./Kbuild treewide: add intermediate .s files to targets treewide: remove explicit rules for *offsets.s firmware: refactor firmware/Makefile firmware: remove unnecessary patterns from .gitignore scripts: remove unnecessary ihex2fw and check-lc_ctypes from .gitignore um: remove unused filechk_gen_header in Makefile scripts: add a tool to produce a compile_commands.json file kbuild: add -Werror=implicit-int flag unconditionally kbuild: add -Werror=strict-prototypes flag unconditionally kbuild: add -fno-PIE flag unconditionally scripts: coccinelle: Correct warning message scripts: coccinelle: only suggest true/false in files that already use them kbuild: handle part-of-module correctly for *.ll and *.symtypes kbuild: refactor part-of-module kbuild: refactor quiet_modtag kbuild: remove redundant quiet_modtag for $(obj-m) kbuild: refactor Makefile.asm-generic user/Makefile: Fix typo and capitalization in comment section ...
2018-12-28Merge tag 'devicetree-for-4.21' of ↵Linus Torvalds4-22/+18
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux Pull Devicetree updates from Rob Herring: "The biggest highlight here is the start of using json-schema for DT bindings. Being able to validate bindings has been discussed for years with little progress. - Initial support for DT bindings using json-schema language. This is the start of converting DT bindings from free-form text to a structured format. - Reworking of initrd address initialization. This moves to using the phys address instead of virt addr in the DT parsing code. This rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary rebuilding of lots of files. - Fix stale phandle entries in phandle cache - DT overlay validation improvements. This exposed several memory leak bugs which have been fixed. - Use node name and device_type helper functions in DT code - Last remaining conversions to using %pOFn printk specifier instead of device_node.name directly - Create new common RTC binding doc and move all trivial RTC devices out of trivial-devices.txt. - New bindings for Freescale MAG3110 magnetometer, Cadence Sierra PHY, and Xen shared memory - Update dtc to upstream version v1.4.7-57-gf267e674d145" * tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits) of: __of_detach_node() - remove node from phandle cache of: of_node_get()/of_node_put() nodes held in phandle cache gpio-omap.txt: add reg and interrupts properties dt-bindings: mrvl,intc: fix a trivial typo dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110 dt-bindings: Convert trivial-devices.txt to json-schema dt-bindings: arm: mrvl: amend Browstone compatible string dt-bindings: arm: Convert Tegra board/soc bindings to json-schema dt-bindings: arm: Convert ZTE board/soc bindings to json-schema dt-bindings: arm: Add missing Xilinx boards dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema dt-bindings: arm: Convert VIA board/soc bindings to json-schema dt-bindings: arm: Convert ST STi board/soc bindings to json-schema dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema dt-bindings: arm: Convert QCom board/soc bindings to json-schema dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema dt-bindings: arm: Convert Altera board/soc bindings to json-schema ...
2018-12-23treewide: add intermediate .s files to targetsMasahiro Yamada1-0/+2
Avoid unneeded recreation of these in the incremental build. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-23treewide: remove explicit rules for *offsets.sMasahiro Yamada1-3/+0
These explicit rules are unneeded because scripts/Makefile.build provides a pattern rule to create %.s from %.c Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-20Merge tag 'zynq-soc-for-v5.0' of https://github.com/Xilinx/linux-xlnx into ↵Arnd Bergmann3-0/+473
next/drivers ARM: Xilinx Zynq SoC patches for v5.0 - Adding pl353 smc driver * tag 'zynq-soc-for-v5.0' of https://github.com/Xilinx/linux-xlnx: memory: pl353: Add driver for arm pl353 static memory controller dt-bindings: memory: Add pl353 smc controller devicetree binding information Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-12-17memory: omap-gpmc: Get the header of the enumLinus Walleij1-0/+1
Commit 21abf103818a ("gpio: Pass a flag to gpiochip_request_own_desc()") started to pass an enum gpiod_flags but this file is not including the header file that defines that enum and the compiler spits: drivers/memory/omap-gpmc.c: In function 'gpmc_probe_generic_child': drivers/memory/omap-gpmc.c:2174:9: error: type of formal parameter 4 is incomplete 0); ^ Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Fixes: 21abf103818a ("gpio: Pass a flag to gpiochip_request_own_desc()") Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-14gpio: Pass a flag to gpiochip_request_own_desc()Linus Walleij1-1/+2
Before things go out of hand, make it possible to pass flags when requesting "own" descriptors from a gpio_chip. This is necessary if the chip wants to request a GPIO with active low semantics, for example. Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Roger Quadros <rogerq@ti.com> Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-13memory: pl353: Add driver for arm pl353 static memory controllerNaga Sureshkumar Relli3-0/+473
Add driver for arm pl353 static memory controller. This controller is used in Xilinx Zynq SoC for interfacing the NAND and NOR/SRAM memory devices. Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-12-12Merge tag 'omap-for-v4.21/driver-part2-signed' of ↵Olof Johansson1-4/+4
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers Few more omap driver fixes and improvments for v4.21 merge window This series of changes improves the TI module flag handling to allow booting with older dts files until the module flags have been moved to the interconnect target module level. And there's a of_node_name_eq() clean-up patch from Rob Herring for the GPMC driver. * tag 'omap-for-v4.21/driver-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: memory: omap-gpmc: Use of_node_name_eq for node name comparisons bus: ti-sysc: Check for no-reset and no-idle flags at the child level ARM: OMAP2+: Check also the first dts child for hwmod flags Signed-off-by: Olof Johansson <olof@lixom.net>
2018-12-11memory: omap-gpmc: Use of_node_name_eq for node name comparisonsRob Herring1-4/+4
Convert string compares of DT node names to use of_node_name_eq helper instead. This removes direct access to the node name pointer. For instances using of_node_cmp, this has the side effect of now using case sensitive comparisons. This should not matter for any FDT based system which this is. Cc: Roger Quadros <rogerq@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-omap@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-11-27memory: Convert to using %pOFn instead of device_node.nameRob Herring4-22/+18
In preparation to remove the node name pointer from struct device_node, convert printf users to use the %pOFn format specifier. Cc: Roger Quadros <rogerq@ti.com> Cc: Kukjin Kim <kgene@kernel.org> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: linux-omap@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-samsung-soc@vger.kernel.org Cc: linux-tegra@vger.kernel.org Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org>
2018-11-08memory: tegra: Introduce Tegra20 EMC driverDmitry Osipenko3-0/+602
Introduce driver for the External Memory Controller (EMC) found on Tegra20 chips, which controls the external DRAM on the board. The purpose of this driver is to program memory timing for external memory on the EMC clock rate change. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-25Merge tag 'at91-4.20-drivers' of ↵Olof Johansson1-2/+1
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into next/drivers AT91 drivers for 4.20 - use struct_size in atmel-ebi * tag 'at91-4.20-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: memory: atmel-ebi: Use struct_size() in devm_kzalloc() Signed-off-by: Olof Johansson <olof@lixom.net>
2018-09-06memory: ti-aemif: fix a potential NULL-pointer dereferenceBartosz Golaszewski1-1/+1
Platform data pointer may be NULL. We check it everywhere but in one place. Fix it. Fixes: 8af70cd2ca50 ("memory: aemif: add support for board files") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Cc: stable@vger.kernel.org Signed-off-by: Olof Johansson <olof@lixom.net>
2018-08-27memory: atmel-ebi: Use struct_size() in devm_kzalloc()Gustavo A. R. Silva1-2/+1
One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct foo { int stuff; void *entry[]; }; instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL); Instead of leaving these open-coded and prone to type mistakes, we can now use the new struct_size() helper: instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL); This issue was detected with the help of Coccinelle. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-08-23Merge tag 'armsoc-drivers' of ↵Linus Torvalds2-10/+39
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Olof Johansson: "Some of the larger changes this merge window: - Removal of drivers for Exynos5440, a Samsung SoC that never saw widespread use. - Uniphier support for USB3 and SPI reset handling - Syste control and SRAM drivers and bindings for Allwinner platforms - Qualcomm AOSS (Always-on subsystem) reset controller drivers - Raspberry Pi hwmon driver for voltage - Mediatek pwrap (pmic) support for MT6797 SoC" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits) drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests soc: fsl: cleanup Kconfig menu soc: fsl: dpio: Convert DPIO documentation to .rst staging: fsl-mc: Remove remaining files staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl staging: fsl-dpaa2: eth: move generic FD defines to DPIO soc: fsl: qe: gpio: Add qe_gpio_set_multiple usb: host: exynos: Remove support for Exynos5440 clk: samsung: Remove support for Exynos5440 soc: sunxi: Add the A13, A23 and H3 system control compatibles reset: uniphier: add reset control support for SPI cpufreq: exynos: Remove support for Exynos5440 ata: ahci-platform: Remove support for Exynos5440 soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs soc: mediatek: pwrap: fix cipher init setting error dt-bindings: pwrap: mediatek: add pwrap support for MT6797 reset: uniphier: add USB3 core reset control dt-bindings: reset: uniphier: add USB3 core reset support ...
2018-08-18Merge tag 'char-misc-4.19-rc1' of ↵Linus Torvalds1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the bit set of char/misc drivers for 4.19-rc1 There is a lot here, much more than normal, seems like everyone is writing new driver subsystems these days... Anyway, major things here are: - new FSI driver subsystem, yet-another-powerpc low-level hardware bus - gnss, finally an in-kernel GPS subsystem to try to tame all of the crazy out-of-tree drivers that have been floating around for years, combined with some really hacky userspace implementations. This is only for GNSS receivers, but you have to start somewhere, and this is great to see. Other than that, there are new slimbus drivers, new coresight drivers, new fpga drivers, and loads of DT bindings for all of these and existing drivers. All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits) android: binder: Rate-limit debug and userspace triggered err msgs fsi: sbefifo: Bump max command length fsi: scom: Fix NULL dereference misc: mic: SCIF Fix scif_get_new_port() error handling misc: cxl: changed asterisk position genwqe: card_base: Use true and false for boolean values misc: eeprom: assignment outside the if statement uio: potential double frees if __uio_register_device() fails eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency misc: ti-st: Fix memory leak in the error path of probe() android: binder: Show extra_buffers_size in trace firmware: vpd: Fix section enabled flag on vpd_section_destroy platform: goldfish: Retire pdev_bus goldfish: Use dedicated macros instead of manual bit shifting goldfish: Add missing includes to goldfish.h mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux dt-bindings: mux: add adi,adgs1408 Drivers: hv: vmbus: Cleanup synic memory free path Drivers: hv: vmbus: Remove use of slow_virt_to_phys() Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind() ...
2018-07-31drivers/memory/Kconfig: Add CONFIG_OF dependencyAnders Roxell1-1/+1
JZ4780_NEMC doesn't depend on OF, and if OF isn't enabled we get this error: drivers/memory/jz4780-nemc.c: In function ‘jz4780_nemc_num_banks’: drivers/memory/jz4780-nemc.c:72:10: error: implicit declaration of function ‘of_read_number’; did you mean ‘down_read_nested’? [-Werror=implicit-function-declaration] bank = of_read_number(prop, 1); ^~~~~~~~~~~~~~ down_read_nested Make JZ4780_NEMC depend on OF. Fixes: ab99e11062c1 ("memory: jz4780-nemc: Allow selection of this driver when COMPILE_TEST=y") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-07-19memory: jz4780-nemc: Allow selection of this driver when COMPILE_TEST=yBoris Brezillon1-1/+2
It just makes maintainers' life easier by allowing them to compile-test this driver without having MACH_JZ4780 enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-07-18memory: fsl_ifc: Allow selection of this driver when COMPILE_TEST=yBoris Brezillon1-1/+2
It just makes maintainers' life easier by allowing them to compile-test this driver without having FSL_SOC, ARCH_LAYERSCAPE or SOC_LS1021A enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-07-14Merge tag 'tegra-for-4.19-memory' of ↵Olof Johansson1-10/+6
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers memory: tegra: Changes for v4.19-rc1 This contains a single fix for the initialization order of the various parts of the Tegra memory controller driver. * tag 'tegra-for-4.19-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: memory: tegra: Correct driver probe order Signed-off-by: Olof Johansson <olof@lixom.net>
2018-07-10memory: tegra: Correct driver probe orderDmitry Osipenko1-10/+6
The Reset Controller should be registered in the end of probe, otherwise Memory Controller device goes away if IRQ requesting fails and the Reset Controller stays registered. To avoid having to unwind the MC probing in a case of SMMU probe failure, let's simply print the error message without failing the MC probe. This allows us to just move the Reset Controller registering before the SMMU registration, reducing code churning. Also let's not fail MC probe in a case of Reset Controller registration failure as it doesn't prevent the MC driver to work. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-07-07headers: separate linux/mod_devicetable.h from linux/platform_device.hRandy Dunlap1-0/+1
At over 4000 #includes, <linux/platform_device.h> is the 9th most #included header file in the Linux kernel. It does not need <linux/mod_devicetable.h>, so drop that header and explicitly add <linux/mod_devicetable.h> to source files that need it. 4146 #include <linux/platform_device.h> After this patch, there are 225 files that use <linux/mod_devicetable.h>, for a reduction of around 3900 times that <linux/mod_devicetable.h> does not have to be read & parsed. 225 #include <linux/mod_devicetable.h> This patch was build-tested on 20 different arch-es. It also makes these drivers SubmitChecklist#1 compliant. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/ Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-26memory: ti-emif-sram: Add resume function to recopy sram codeDave Gerlach1-0/+33
After an RTC+DDR cycle we lose sram context so emif pm functions present in sram are lost. We can check if the first byte of the original code in DDR contains the same first byte as the code in sram, and if they do not match we know we have lost context and must recopy the functions to the previous address to maintain PM functionality. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
2018-06-12Merge tag 'overflow-v4.18-rc1-part2' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull more overflow updates from Kees Cook: "The rest of the overflow changes for v4.18-rc1. This includes the explicit overflow fixes from Silvio, further struct_size() conversions from Matthew, and a bug fix from Dan. But the bulk of it is the treewide conversions to use either the 2-factor argument allocators (e.g. kmalloc(a * b, ...) into kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a * b) into vmalloc(array_size(a, b)). Coccinelle was fighting me on several fronts, so I've done a bunch of manual whitespace updates in the patches as well. Summary: - Error path bug fix for overflow tests (Dan) - Additional struct_size() conversions (Matthew, Kees) - Explicitly reported overflow fixes (Silvio, Kees) - Add missing kvcalloc() function (Kees) - Treewide conversions of allocators to use either 2-factor argument variant when available, or array_size() and array3_size() as needed (Kees)" * tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits) treewide: Use array_size in f2fs_kvzalloc() treewide: Use array_size() in f2fs_kzalloc() treewide: Use array_size() in f2fs_kmalloc() treewide: Use array_size() in sock_kmalloc() treewide: Use array_size() in kvzalloc_node() treewide: Use array_size() in vzalloc_node() treewide: Use array_size() in vzalloc() treewide: Use array_size() in vmalloc() treewide: devm_kzalloc() -> devm_kcalloc() treewide: devm_kmalloc() -> devm_kmalloc_array() treewide: kvzalloc() -> kvcalloc() treewide: kvmalloc() -> kvmalloc_array() treewide: kzalloc_node() -> kcalloc_node() treewide: kzalloc() -> kcalloc() treewide: kmalloc() -> kmalloc_array() mm: Introduce kvcalloc() video: uvesafb: Fix integer overflow in allocation UBIFS: Fix potential integer overflow in allocation leds: Use struct_size() in allocation Convert intel uncore to struct_size ...
2018-06-12treewide: devm_kzalloc() -> devm_kcalloc()Kees Cook1-2/+2
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc(). This patch replaces cases of: devm_kzalloc(handle, a * b, gfp) with: devm_kcalloc(handle, a * b, gfp) as well as handling cases of: devm_kzalloc(handle, a * b * c, gfp) with: devm_kzalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kcalloc(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kzalloc + devm_kcalloc (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, C1 * C2, ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-05-25Merge tag 'tegra-for-4.18-memory-v2' of ↵Olof Johansson11-308/+807
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers memory: tegra: Changes for v4.18-rc1 This contains some cleanup of the memory controller driver as well as unification work to share more code between Tegra20 and later SoC generations. Also included are an implementation for the hot resets functionality by the memory controller which is required to properly reset busy hardware. * tag 'tegra-for-4.18-memory-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions memory: tegra: Remove Tegra114 SATA and AFI reset definitions memory: tegra: Register SMMU after MC driver became ready memory: tegra: Add Tegra210 memory controller hot resets memory: tegra: Add Tegra124 memory controller hot resets memory: tegra: Add Tegra114 memory controller hot resets memory: tegra: Add Tegra30 memory controller hot resets memory: tegra: Add Tegra20 memory controller hot resets memory: tegra: Introduce memory client hot reset memory: tegra: Squash tegra20-mc into common tegra-mc driver memory: tegra: Remove unused headers inclusions memory: tegra: Apply interrupts mask per SoC memory: tegra: Setup interrupts mask before requesting IRQ memory: tegra: Do not handle spurious interrupts dt-bindings: memory: tegra: Add hot resets definitions Signed-off-by: Olof Johansson <olof@lixom.net>
2018-05-18memory: tegra: Remove Tegra114 SATA and AFI reset definitionsDmitry Osipenko1-2/+0
Tegra114 doesn't have SATA nor PCIe, but TRM seems erroneously document them. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-05-18memory: tegra: Register SMMU after MC driver became readyDmitry Osipenko1-9/+9
Memory Controller driver invokes SMMU driver registration and MC's registers mapping is shared with SMMU. This mapping goes away if MC driver probing fails after SMMU registration. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-05-14Merge tag 'arm-soc/for-4.18/drivers' of https://github.com/Broadcom/stblinux ↵Olof Johansson1-32/+10
into next/drivers This pull request contains Broadcom ARM/ARM64/MIPS SoCs drivers changes for 4.18, please pull the following: - Florian removes the synthetic struct device in the DPFE driver which was used to attach sysfs attributes and uses the platform_device we are probed from instead. * tag 'arm-soc/for-4.18/drivers' of https://github.com/Broadcom/stblinux: memory: brcmstb: dpfe: Remove need for dpfe_dev Signed-off-by: Olof Johansson <olof@lixom.net>
2018-05-14Merge tag 'gpmc-omap-for-v4.18' of https://github.com/rogerq/linux into ↵Olof Johansson1-2/+2
next/drivers OMAP-GPMC: driver updates for v4.18 * get rid of a redundant NULL check in gpmc_probe_dt_children() * tag 'gpmc-omap-for-v4.18' of https://github.com/rogerq/linux: memory: omap-gpmc: Avoid redundant NULL check Signed-off-by: Olof Johansson <olof@lixom.net>
2018-05-14Merge tag 'soc_drivers_for_4.18' of ↵Olof Johansson1-21/+39
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/drivers ARM: SOC driver update for 4.18 - AEMIF driver update to support board files and remove need of mach-davinci aemif code - Use percpu counters for qmss datapath stats - License update for TI SCI * tag 'soc_drivers_for_4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: firmware: ti_sci: Switch to SPDX Licensing soc: ti: knav_qmss: Use percpu instead atomic for stats counter memory: aemif: add support for board files memory: aemif: don't rely on kbuild for driver's name Signed-off-by: Olof Johansson <olof@lixom.net>
2018-05-09memory: brcmstb: dpfe: Remove need for dpfe_devFlorian Fainelli1-32/+10
We can hook sysfs objects to the parent platform device that we are created from, no need to have a synthetic dpfe_dev just for that. This incidentally removes the need for having an index, since we are guaranteed to have an unique path in the sysfs hiearchy. Acked-by: Markus Mayer <mmayer@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-04-30memory: tegra: Add Tegra210 memory controller hot resetsThierry Reding1-0/+45
Define the table of memory controller hot resets for Tegra210. Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-04-30memory: tegra: Add Tegra124 memory controller hot resetsDmitry Osipenko1-0/+42
Define the table of memory controller hot resets for Tegra124. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-04-30memory: tegra: Add Tegra114 memory controller hot resetsDmitry Osipenko1-0/+33
Define the table of memory controller hot resets for Tegra114. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-04-30memory: tegra: Add Tegra30 memory controller hot resetsDmitry Osipenko1-0/+33
Define the table of memory controller hot resets for Tegra30. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-04-30memory: tegra: Add Tegra20 memory controller hot resetsDmitry Osipenko1-0/+118
Define the table of memory controller hot resets for Tegra20 and add specific to Tegra20 hot reset operations. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-04-30memory: tegra: Introduce memory client hot resetDmitry Osipenko2-0/+212
In order to reset busy HW properly, memory controller needs to be involved, otherwise it is possible to get corrupted memory or hang machine if HW was reset during DMA. Introduce memory client 'hot reset' that will be used for resetting of busy HW. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-03 15:25:22 +0000