summaryrefslogtreecommitdiffstats
path: root/drivers/media/i2c/tda1997x.c
AgeCommit message (Collapse)AuthorFilesLines
2021-10-19media: TDA1997x: replace video detection routineKrzysztof Hałasa1-52/+67
The TDA1997x (HDMI receiver) driver currently uses a specific video format detection scheme. The frame (or field in interlaced mode), line and HSync pulse durations are compared to those of known, standard video modes. If a match is found, the mode is assumed to be detected, otherwise -ERANGE is returned (then possibly ignored). This means that: - another mode with similar timings will be detected incorrectly (e.g. 2x faster clock and lines twice as long) - non-standard modes will not work. This patch replaces this scheme with a direct read of geometry registers. This way all modes recognized by the chip are supported. In interlaced modes, the code assumes the V sync signal has the same duration for both fields. While this may be not necessarily true, I can't see any way to get the "other" V sync width. This is most probably harmless. All tests have been performed on Gateworks' Ventana GW54xx board, with a TDA19971 chip. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Tested-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-09-30media: TDA1997x: handle short reads of hdmi info frame.Tom Rix1-4/+4
Static analysis reports this representative problem tda1997x.c:1939: warning: 7th function call argument is an uninitialized value The 7th argument is buffer[0], which is set in the earlier call to io_readn(). When io_readn() call to io_read() fails with the first read, buffer[0] is not set and 0 is returned and stored in len. The later call to hdmi_infoframe_unpack()'s size parameter is the static size of buffer, always 40, so a short read is not caught in hdmi_infoframe_unpacks()'s checking. The variable len should be used instead. Zero initialize buffer to 0 so it is in a known start state. Fixes: 9ac0038db9a7 ("media: i2c: Add TDA1997x HDMI receiver driver") Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-09-30media: TDA1997x: fix tda1997x_remove()Krzysztof Hałasa1-2/+2
TDA1997x driver tried to hold two values in a single variable: device's "client data" pointer was first set to "sd" in v4l2_i2c_subdev_init(), then it was overwritten explicitly using dev_set_drvdata() with "state". This caused tda1997x_remove() to fail badly. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04media: TDA1997x: report -ENOLINK after disconnecting HDMI sourceKrzysztof Hałasa1-1/+2
The TD1997x chip retains vper, hper and hsper register values when the HDMI source is disconnected. Use a different means of checking if the link is still valid. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04media: TDA1997x: fix tda1997x_query_dv_timings() return valueKrzysztof Hałasa1-2/+3
Correctly propagate the tda1997x_detect_std error value. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04media: Fix cosmetic error in TDA1997x driverKrzysztof Hałasa1-1/+1
The colon isn't followed by anything here. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-07-12media: TDA1997x: enable EDID supportKrzysztof Hałasa1-0/+1
Without this patch, the TDA19971 chip's EDID is inactive. EDID never worked with this driver, it was all tested with HDMI signal sources which don't need EDID support. Signed-off-by: Krzysztof Halasa <khalasa@piap.pl> Fixes: 9ac0038db9a7 ("media: i2c: Add TDA1997x HDMI receiver driver") Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-06-17media: v4l2-subdev: add subdev-wide state structTomi Valkeinen1-7/+7
We have 'struct v4l2_subdev_pad_config' which contains configuration for a single pad used for the TRY functionality, and an array of those structs is passed to various v4l2_subdev_pad_ops. I was working on subdev internal routing between pads, and realized that there's no way to add TRY functionality for routes, which is not pad specific configuration. Adding a separate struct for try-route config wouldn't work either, as e.g. set-fmt needs to know the try-route configuration to propagate the settings. This patch adds a new struct, 'struct v4l2_subdev_state' (which at the moment only contains the v4l2_subdev_pad_config array) and the new struct is used in most of the places where v4l2_subdev_pad_config was used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config are changed to instead take v4l2_subdev_state. The changes to drivers/media/v4l2-core/v4l2-subdev.c and include/media/v4l2-subdev.h were written by hand, and all the driver changes were done with the semantic patch below. The spatch needs to be applied to a select list of directories. I used the following shell commands to apply the spatch: dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media" for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done Note that Coccinelle chokes on a few drivers (gcc extensions?). With minor changes we can make Coccinelle run fine, and these changes can be reverted after spatch. The diff for these changes is: For drivers/media/i2c/s5k5baf.c: @@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd, &s5k5baf_cis_rect, v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS), v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS), - v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT) + v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT), }; s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r); return 0; For drivers/media/platform/s3c-camif/camif-capture.c: @@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd, *mf = camif->mbus_fmt; break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* crop rectangle at camera interface input */ mf->width = camif->camif_crop.width; mf->height = camif->camif_crop.height; @@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd, } break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* Pixel format can be only changed on the sink pad. */ mf->code = camif->mbus_fmt.code; mf->width = crop->width; The semantic patch is: // <smpl> // Change function parameter @@ identifier func; identifier cfg; @@ func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...) { <... - cfg + sd_state ...> } // Change function declaration parameter @@ identifier func; identifier cfg; type T; @@ T func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...); // Change function return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...) { ... } // Change function declaration return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...); // Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it // inside a pad_state. @@ identifier func; identifier pad_cfg; @@ func(...) { ... struct v4l2_subdev_pad_config pad_cfg; + struct v4l2_subdev_state pad_state = { .pads = &pad_cfg }; <+... ( v4l2_subdev_call | sensor_call | isi_try_fse | isc_try_fse | saa_call_all ) (..., - &pad_cfg + &pad_state ,...) ...+> } // If the function uses fields from pad_config, access via state->pads @@ identifier func; identifier state; @@ func(..., struct v4l2_subdev_state *state , ...) { <... ( - state->try_fmt + state->pads->try_fmt | - state->try_crop + state->pads->try_crop | - state->try_compose + state->pads->try_compose ) ...> } // If the function accesses the filehandle, use fh->state instead @@ struct v4l2_subdev_fh *fh; @@ - fh->pad + fh->state @@ struct v4l2_subdev_fh fh; @@ - fh.pad + fh.state // Start of vsp1 specific @@ @@ struct vsp1_entity { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... }; @@ symbol entity; @@ vsp1_entity_init(...) { ... entity->config = - v4l2_subdev_alloc_pad_config + v4l2_subdev_alloc_state (&entity->subdev); ... } @@ symbol entity; @@ vsp1_entity_destroy(...) { ... - v4l2_subdev_free_pad_config + v4l2_subdev_free_state (entity->config); ... } @exists@ identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)"; symbol config; @@ func(...) { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... } // End of vsp1 specific // Start of rcar specific @@ identifier sd; identifier pad_cfg; @@ rvin_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } // End of rcar specific // Start of rockchip specific @@ identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)"; symbol rsz; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = rsz->pad_cfg }; ... - rsz->pad_cfg + &state ... } @@ identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)"; symbol isp; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = isp->pad_cfg }; ... - isp->pad_cfg + &state ... } @@ symbol rkisp1; symbol isp; symbol pad_cfg; @@ rkisp1_isp_register(...) { + struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg }; ... - rkisp1->isp.pad_cfg + &state ... } // End of rockchip specific // Start of tegra-video specific @@ identifier sd; identifier pad_cfg; @@ __tegra_channel_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } @@ identifier sd_state; @@ __tegra_channel_try_format(...) { ... struct v4l2_subdev_state *sd_state; <... - sd_state->try_crop + sd_state->pads->try_crop ...> } // End of tegra-video specific // </smpl> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-04-09media: i2c: tda1997: Fix possible use-after-free in tda1997x_remove()Yang Yingliang1-1/+1
This driver's remove path calls cancel_delayed_work(). However, that function does not wait until the work function finishes. This means that the callback function may still be running after the driver's remove function has finished, which would result in a use-after-free. Fix by calling cancel_delayed_work_sync(), which ensures that the work is properly cancelled, no longer running, and unable to re-schedule itself. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-08-29media: Use fallthrough pseudo-keywordGustavo A. R. Silva1-5/+5
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-08-29media: i2c: tda1997x.c: Fix assignment of 0/1 to bool variableDaniel W. S. Almeida1-3/+3
Fix the following coccinelle reports: drivers/media/i2c/tda1997x.c:911:6-21: WARNING: Assignment of 0/1 to bool variable drivers/media/i2c/tda1997x.c:939:2-17: WARNING: Assignment of 0/1 to bool variable drivers/media/i2c/tda1997x.c:947:4-19: WARNING: Assignment of 0/1 to bool variable Replace assignment to 1 with true and assignment to 0 with false. Found using - Coccinelle (http://coccinelle.lip6.fr) Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2019-08-13media: i2c: tda1997x: prevent potential NULL pointer accessWolfram Sang1-2/+7
i2c_new_dummy() can fail returning a NULL pointer. This is not checked and the returned pointer is blindly used. Convert to devm_i2c_new_dummy_client() which returns an ERR_PTR and also add a validity check. Using devm_* here also fixes a leak because the dummy client was not released in the probe error path. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-02-18media: tda1997x: fix get_edidTim Harvey1-0/+4
set_edid never wrote the new EDID to state->edid.edid, it was only written to the hardware. Since get_edid returned state->edid.edid, it was never returning the right EDID. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> [hverkuil-cisco@xs4all.nl: added missing commit log] Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-11-19Merge tag 'drm-misc-next-2018-11-07' of ↵Dave Airlie1-2/+2
git://anongit.freedesktop.org/drm/drm-misc into drm-next drm-misc-next for v4.21, part 1: UAPI Changes: - Add syncobj timeline support to drm. Cross-subsystem Changes: - Remove shared fence staging in dma-buf's fence object, and allow reserving more than 1 fence and add more paranoia when debugging. - Constify infoframe functions in video/hdmi. Core Changes: - Add vkms todo, and a lot of assorted doc fixes. - Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown(). - Move atomic state helper functions to drm_atomic_state_helper.[ch] - Refactor drm selftests, and add new tests. - DP MST atomic state cleanups. - Drop EXPORT_SYMBOL from drm leases. - Lease cleanups and fixes. - Create render node for vgem. Driver Changes: - Fix build failure in imx without fbdev emulation. - Add rotation quirk for GPD win2 panel. - Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG, Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA, Himax HX8357D, simulated RTSM AEMv8. - Add dw_hdmi support to rockchip driver. - Fix YUV support in vc4. - Fix resource id handling in virtio. - Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support. - Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR. - Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup(). - Add Mali linear tiled formats, and enable them in the Mali-DP driver. - Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP. - Assorted driver cleanups and fixes. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/be7ebd91-edd9-8fa4-4286-1c57e3165113@linux.intel.com
2018-10-04media: v4l: fwnode: Initialise the V4L2 fwnode endpoints to zeroSakari Ailus1-1/+1
Initialise the V4L2 fwnode endpoints to zero in all drivers using v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint flags as well as the bus type. Setting bus type to zero will continue to guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY). Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-10-01video/hdmi: Pass buffer size to infoframe unpack functionsVille Syrjälä1-2/+2
To make sure the infoframe unpack functions don't end up examining stack garbage or oopsing, let's pass in the size of the buffer. v2: Convert tda1997x.c as well (kbuild test robot) Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Hans Verkuil <hans.verkuil@cisco.com> Cc: linux-media@vger.kernel.org Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180920185145.1912-3-ville.syrjala@linux.intel.com Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
2018-07-25media: rename MEDIA_ENT_F_DTV_DECODER to MEDIA_ENT_F_DV_DECODERHans Verkuil1-1/+1
The use of 'DTV' is very confusing since it normally refers to Digital TV e.g. DVB etc. Instead use 'DV' (Digital Video), which nicely corresponds to the DV Timings API used to configure such receivers and transmitters. We keep an alias to avoid breaking userspace applications. Since this alias is only available if __KERNEL__ is *not* defined (i.e. it is only available for userspace, not kernelspace), any drivers that use it also have to be converted to the new define. These drivers are adv7604, adv7842 and tda1997x. Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-06-07Merge tag 'media/v4.18-2' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media Pull media updates from Mauro Carvalho Chehab: - remove of atomisp driver from staging, as nobody would have time to dedicate huge efforts to fix all the problems there. Also, we have a feeling that the driver may not even run the way it is. - move Zoran driver to staging, in order to be either fixed to use VB2 and the proper media kAPIs or to be removed - remove videobuf-dvb driver, with is unused for a while - some V4L2 documentation fixes/improvements - new sensor drivers: imx258 and ov7251 - a new driver was added to allow using I2C transparent drivers - several improvements at the ddbridge driver - several improvements at the ISDB pt1 driver, making it more coherent with the DVB framework - added a new platform driver for MIPI CSI-2 RX: cadence - now, all media drivers can be compiled on x86 with COMPILE_TEST - almost all media drivers now build on non-x86 architectures with COMPILE_TEST - lots of other random stuff: cleanups, support for new board models, bug fixes, etc * tag 'media/v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits) media: omap2: fix compile-testing with FB_OMAP2=m media: media/radio/Kconfig: add back RADIO_ISA media: v4l2-ioctl.c: fix missing unlock in __video_do_ioctl() media: pxa_camera: ignore -ENOIOCTLCMD from v4l2_subdev_call for s_power media: arch: sh: migor: Fix TW9910 PDN gpio media: staging: tegra-vde: Reset VDE regardless of memory client resetting failure media: marvel-ccic: mmp: select VIDEOBUF2_VMALLOC/DMA_CONTIG media: marvel-ccic: allow ccic and mmp drivers to coexist media: uvcvideo: Prevent setting unavailable flags media: ddbridge: conditionally enable fast TS for stv0910-equipped bridges media: dvb-frontends/stv0910: make TS speed configurable media: ddbridge/mci: add identifiers to function definition arguments media: ddbridge/mci: protect against out-of-bounds array access in stop() media: rc: ensure input/lirc device can be opened after register media: rc: nuvoton: Keep device enabled during reg init media: rc: nuvoton: Keep track of users on CIR enable/disable media: rc: nuvoton: Tweak the interrupt enabling dance media: uvcvideo: Support realtek's UVC 1.5 device media: uvcvideo: Fix driver reference counting media: gspca_zc3xx: Enable short exposure times for OV7648 ...
2018-05-11media: i2c: tda1997: Fix an error handling path 'tda1997x_probe()'Christophe JAILLET1-1/+1
If 'media_entity_pads_init()' fails, we must free the resources allocated by 'v4l2_ctrl_handler_init()', as already done in the previous error handling path. 'goto' the right label to fix it. Fixes: 9ac0038db9a7 ("media: i2c: Add TDA1997x HDMI receiver driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-05-05media: i2c: tda1997: replace codec to componentKuninori Morimoto1-12/+13
Now we can replace Codec to Component. Let's do it. Note: xxx_codec_xxx() -> xxx_component_xxx() .idle_bias_off = 0 -> .idle_bias_on = 1 .ignore_pmdown_time = 0 -> .use_pmdown_time = 1 - -> .endianness = 1 - -> .non_legacy_dai_naming = 1 Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-23media: tda1997x: Use bitwise or for setting subdev flagsSakari Ailus1-1/+1
Assigning subdev flags in probe() after v4l2_i2c_subdev_init() clears the I2C flag set by that function. Fix this by using bitwise or instead. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2018-02-22tda1997x: get rid of an unused varMauro Carvalho Chehab1-2/+2
1 warning regressions: + drivers/media/i2c/tda1997x.c: warning: variable 'last_irq_status' set but not used [-Wunused-but-set-variable]: => 1421:17 Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2018-02-22media: i2c: Add TDA1997x HDMI receiver driverTim Harvey1-0/+2820
Add support for the TDA1997x HDMI receivers. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> [hans.verkuil@cisco.com: fix type 'testin' -> 'testing'] Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-10-27 15:54:52 +0000