summaryrefslogtreecommitdiffstats
path: root/drivers/media/i2c/ov5640.c
AgeCommit message (Collapse)AuthorFilesLines
2021-08-04media: ov5640: Complement yuv mbus formats with their 1X16 versionsXavier Roumegue1-0/+4
According to media bus pixel codes definition, data formats on serial busses should be described with one bus sample per pixel. Documentation/userspace-api/media/v4l/subdev-formats.rst states: "The media bus pixel codes document parallel formats. Should the pixel data be transported over a serial bus, the media bus pixel code that describes a parallel format that transfers a sample on a single clock cycle is used. For instance, both MEDIA_BUS_FMT_BGR888_1X24 and MEDIA_BUS_FMT_BGR888_3X8 are used on parallel busses for transferring an 8 bits per sample BGR data, whereas on serial busses the data in this format is only referred to using MEDIA_BUS_FMT_BGR888_1X24. This is because there is effectively only a single way to transport that format on the serial busses." Some MIPI CSI receivers strictly obey this definition and declare support for only *1X_* formats. Hence, complement the supported media bus formats with their 1X16 versions (currently applicable to yuyv, uyvy) to enhance interoperability with CSI receivers. Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-06-17media: v4l2-subdev: add subdev-wide state structTomi Valkeinen1-7/+7
We have 'struct v4l2_subdev_pad_config' which contains configuration for a single pad used for the TRY functionality, and an array of those structs is passed to various v4l2_subdev_pad_ops. I was working on subdev internal routing between pads, and realized that there's no way to add TRY functionality for routes, which is not pad specific configuration. Adding a separate struct for try-route config wouldn't work either, as e.g. set-fmt needs to know the try-route configuration to propagate the settings. This patch adds a new struct, 'struct v4l2_subdev_state' (which at the moment only contains the v4l2_subdev_pad_config array) and the new struct is used in most of the places where v4l2_subdev_pad_config was used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config are changed to instead take v4l2_subdev_state. The changes to drivers/media/v4l2-core/v4l2-subdev.c and include/media/v4l2-subdev.h were written by hand, and all the driver changes were done with the semantic patch below. The spatch needs to be applied to a select list of directories. I used the following shell commands to apply the spatch: dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media" for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done Note that Coccinelle chokes on a few drivers (gcc extensions?). With minor changes we can make Coccinelle run fine, and these changes can be reverted after spatch. The diff for these changes is: For drivers/media/i2c/s5k5baf.c: @@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd, &s5k5baf_cis_rect, v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS), v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS), - v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT) + v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT), }; s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r); return 0; For drivers/media/platform/s3c-camif/camif-capture.c: @@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd, *mf = camif->mbus_fmt; break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* crop rectangle at camera interface input */ mf->width = camif->camif_crop.width; mf->height = camif->camif_crop.height; @@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd, } break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* Pixel format can be only changed on the sink pad. */ mf->code = camif->mbus_fmt.code; mf->width = crop->width; The semantic patch is: // <smpl> // Change function parameter @@ identifier func; identifier cfg; @@ func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...) { <... - cfg + sd_state ...> } // Change function declaration parameter @@ identifier func; identifier cfg; type T; @@ T func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...); // Change function return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...) { ... } // Change function declaration return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...); // Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it // inside a pad_state. @@ identifier func; identifier pad_cfg; @@ func(...) { ... struct v4l2_subdev_pad_config pad_cfg; + struct v4l2_subdev_state pad_state = { .pads = &pad_cfg }; <+... ( v4l2_subdev_call | sensor_call | isi_try_fse | isc_try_fse | saa_call_all ) (..., - &pad_cfg + &pad_state ,...) ...+> } // If the function uses fields from pad_config, access via state->pads @@ identifier func; identifier state; @@ func(..., struct v4l2_subdev_state *state , ...) { <... ( - state->try_fmt + state->pads->try_fmt | - state->try_crop + state->pads->try_crop | - state->try_compose + state->pads->try_compose ) ...> } // If the function accesses the filehandle, use fh->state instead @@ struct v4l2_subdev_fh *fh; @@ - fh->pad + fh->state @@ struct v4l2_subdev_fh fh; @@ - fh.pad + fh.state // Start of vsp1 specific @@ @@ struct vsp1_entity { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... }; @@ symbol entity; @@ vsp1_entity_init(...) { ... entity->config = - v4l2_subdev_alloc_pad_config + v4l2_subdev_alloc_state (&entity->subdev); ... } @@ symbol entity; @@ vsp1_entity_destroy(...) { ... - v4l2_subdev_free_pad_config + v4l2_subdev_free_state (entity->config); ... } @exists@ identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)"; symbol config; @@ func(...) { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... } // End of vsp1 specific // Start of rcar specific @@ identifier sd; identifier pad_cfg; @@ rvin_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } // End of rcar specific // Start of rockchip specific @@ identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)"; symbol rsz; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = rsz->pad_cfg }; ... - rsz->pad_cfg + &state ... } @@ identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)"; symbol isp; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = isp->pad_cfg }; ... - isp->pad_cfg + &state ... } @@ symbol rkisp1; symbol isp; symbol pad_cfg; @@ rkisp1_isp_register(...) { + struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg }; ... - rkisp1->isp.pad_cfg + &state ... } // End of rockchip specific // Start of tegra-video specific @@ identifier sd; identifier pad_cfg; @@ __tegra_channel_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } @@ identifier sd_state; @@ __tegra_channel_try_format(...) { ... struct v4l2_subdev_state *sd_state; <... - sd_state->try_crop + sd_state->pads->try_crop ...> } // End of tegra-video specific // </smpl> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-04-06media: v4l: fwnode: Rename v4l2_async_register_subdev_sensor_commonSakari Ailus1-1/+1
Rename v4l2_async_register_subdev_sensor_common as v4l2_async_register_subdev_sensor. This is a part of the effort to make the long names present in V4L2 fwnode and async frameworks shorter. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-11-16media: ov5640: fix support of BT656 bus modeHugues Fruchet1-37/+45
Fix PCLK polarity not being taken into account. Add comments about BT656 register control. Remove useless ov5640_set_stream_bt656() function. Refine comments about MIPI IO register control. Fixes: 4039b03720f7 ("media: i2c: ov5640: Add support for BT656 mode") Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-11-16media: ov5640: add support of 160x120 resolutionHugues Fruchet1-1/+25
Add support of 160x120 resolution. Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-09-10media: i2c: ov5640: Fail probe on unsupported bus_typeLad Prabhakar1-0/+7
Fail probe if unsupported bus_type is detected. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-09-10media: i2c: ov5640: Add support for BT656 modeLad Prabhakar1-12/+34
Enable support for BT656 mode. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-09-10media: i2c: ov5640: Configure HVP lines in s_power callbackLad Prabhakar1-65/+58
Configure HVP lines in s_power callback instead of configuring everytime in ov5640_set_stream_dvp(). Alongside also disable MIPI in DVP mode. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Tested-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-09-10media: i2c: ov5640: Enable data pins on poweron for DVP modeLad Prabhakar1-33/+40
During testing this sensor on iW-RainboW-G21D-Qseven platform in 8-bit DVP mode with rcar-vin bridge noticed the capture worked fine for the first run (with yavta), but for subsequent runs the bridge driver waited for the frame to be captured. Debugging further noticed the data lines were enabled/disabled in stream on/off callback and dumping the register contents 0x3017/0x3018 in ov5640_set_stream_dvp() reported the correct values, but yet frame capturing failed. To get around this issue data lines are enabled in s_power callback. (Also the sensor remains in power down mode if not streaming so power consumption shouldn't be affected) Fixes: f22996db44e2d ("media: ov5640: add support of DVP parallel interface") Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Tested-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-09-10media: i2c: ov5640: Separate out mipi configuration from s_powerLad Prabhakar1-56/+60
In preparation for adding DVP configuration in s_power callback move mipi configuration into separate function Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Tested-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-09-10media: i2c: ov5640: Remain in power down for DVP mode unless streamingLad Prabhakar1-3/+16
Keep the sensor in software power down mode and wake up only in ov5640_set_stream_dvp() callback. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Tested-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-09-01media: ov5640: Correct Bit Div register in clock tree diagramPaul Kocialkowski1-1/+1
Although the code is correct and doing the right thing, the clock diagram showed the wrong register for the bit divider, which had me doubting the understanding of the tree. Fix this to avoid doubts in the future. Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Fixes: aa2882481cada ("media: ov5640: Adjust the clock based on the expected rate") Acked-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-08-29media: Use fallthrough pseudo-keywordGustavo A. R. Silva1-1/+1
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-04-14media: ov5640: fix use of destroyed mutexTomi Valkeinen1-2/+2
v4l2_ctrl_handler_free() uses hdl->lock, which in ov5640 driver is set to sensor's own sensor->lock. In ov5640_remove(), the driver destroys the sensor->lock first, and then calls v4l2_ctrl_handler_free(), resulting in the use of the destroyed mutex. Fix this by calling moving the mutex_destroy() to the end of the cleanup sequence, as there's no need to destroy the mutex as early as possible. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: stable@vger.kernel.org # v4.14+ Reviewed-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-01-04media: ov5640: Fix check for PLL1 exceeding max allowed rateAdam Ford1-1/+1
The variable _rate is by ov5640_compute_sys_clk() which returns zero if the PLL exceeds 1GHz. Unfortunately, the check to see if the max PLL1 output is checking 'rate' and not '_rate' and 'rate' does not ever appear to be 0. This patch changes the check against the returned value of '_rate' to determine if the PLL1 output exceeds 1GHz. Fixes: aa2882481cad ("media: ov5640: Adjust the clock based on the expected rate") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-01-04media: ov5640: Put max framerate into table and simplify checkAdam Ford1-17/+22
Currently the various modes are placed into a table, but when ov5640_find_mode is called, it has to double check whether or not the requested framerate is tolerated by the mode. The determination is based on checking hact, vact, and frame rate. Only 640x480 is allowed at 60fps and QSXGA is limited to 15fps, but as the number of permitted frame rates change, this will begin to add more and more complexity to the check. This patch simplifies the check by adding the max framerate allowed for each mode into the table of modes. It then compares the requested framerate to the max permitted in the mode's table. This reduces the number of comparisions to one down from three at run-time. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2019-10-24media: ov5640: Make 2592x1944 mode only available at 15 fpsBenoit Parrot1-0/+5
The sensor data sheet clearly state that 2592x1944 only works at 15 fps make sure we don't try to miss configure the pll out of acceptable range. Signed-off-by: Benoit Parrot <bparrot@ti.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-10-24media: ov5640: Fix 1920x1080 mode to remove extra enable/disableBenoit Parrot1-2/+1
In the 1920x1080 register array an extra pair of reset ctrl disable re-enable was causing unwanted init delays. Signed-off-by: Benoit Parrot <bparrot@ti.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-10-24media: ov5640: add PIXEL_RATE controlBenoit Parrot1-2/+23
Add v4l2 controls to report the pixel rates of each mode. This is needed by some CSI2 receiver in order to perform proper DPHY configuration. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-08-15media: ov5640: Add support for flash and lens devicesLuca Weiss1-1/+1
Parse async sub-devices related to the sensor by switching the async sub-device registration function. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-08-13media: i2c: Convert to new i2c device probe()Kieran Bingham1-3/+2
The I2C core framework provides a simplified probe framework from commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type"). These drivers do not utilise the i2c_device_id table in the probe, so we can easily convert them to utilise the simplified i2c driver registration. Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Acked-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-07-25media: i2c: ov5640: Fix the order for enabling regulatorsFabio Estevam1-1/+1
According to the OV5640 datasheet the following sequence needs to be followed when powering the OV5640 supplies: - DOVDD - AVDD - DVDD So follow this order inside the ov5640_supply_name[] array, so that the regulator_bulk() functions can enable the regulator in the correct sequence. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-07-25media: i2c: ov5640: Check for devm_gpiod_get_optional() errorFabio Estevam1-0/+5
The power down and reset GPIO are optional, but the return value from devm_gpiod_get_optional() needs to be checked and propagated in the case of error, so that probe deferral can work. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner1-5/+1
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-01media: i2c: fix several typosMauro Carvalho Chehab1-1/+1
Use codespell to fix lots of typos over frontends. Manually verified to avoid false-positives. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-02-18media: i2c: ov5640: Fix post-reset delayLoic Poulain1-1/+1
According to the ov5640 specification (2.7 power up sequence), host can access the sensor's registers 20ms after reset. Trying to access them before leads to undefined behavior and result in sporadic initialization errors. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-02-18media: ov5640: Fix set 15fps regressionJagan Teki1-1/+1
The ov5640_try_frame_interval operation updates the FPS as per user input based on default ov5640_frame_rate, OV5640_30_FPS which is failed to update when user trigger 15fps. So, initialize the default ov5640_frame_rate to OV5640_15_FPS so-that it can satisfy to update all fps. Fixes: 5a3ad937bc78 ("media: ov5640: Make the return rate type more explicit") Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-02-18media: ov5640: Consolidate JPEG compression mode settingChen-Yu Tsai1-11/+23
The register value lists for all the supported resolution settings all include a register address/value pair for setting the JPEG compression mode. With the exception of 1080p (which sets mode 2), all resolutions use mode 3. The only difference between mode 2 and mode 3 is that mode 2 may have padding data on the last line, while mode 3 does not add padding data. As these register values were from dumps of running systems, and the difference between the modes is quite small, using mode 3 for all configurations should be OK. [Sakari Ailus: Align OV5640_REG_JPG_MODE_SELECT register naming.] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-02-18media: ov5640: Set JPEG output timings when outputting JPEG dataChen-Yu Tsai1-0/+21
When compression is turned on, the on-bus data is framed according to the compression mode, and the height and width set in VFIFO_VSIZE and VFIFO_HSIZE. If these are not updated correctly, the sensor will send data framed in a manner unexpected by the capture interface, such as having more bytes per line than expected, and having the extra data dropped. This ultimately results in corrupted data. Set the two values when the media bus is configured for JPEG data, meaning the sensor would be in JPEG mode. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-02-18media: ov5640: Add three more test patternsChen-Yu Tsai1-0/+7
The OV5640 driver currently supports a static color bar pattern with a small vertical gamma gradient. The hardware also supports a color square pattern, as well as having a rolling bar for dynamic sequences. Add three more test patterns: - color bars with a rolling bar (but without the gamma gradient) - static color squares - color squares with a rolling bar Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-02-18media: ov5640: Disable transparent feature for test patternChen-Yu Tsai1-2/+1
The transparent feature for test patterns blends the test pattern with an actual captured image. This makes the result non-static, subject to changes in the sensor's field of view. Test patterns should be predictable and deterministic, even if they are dynamic patterns. Disable the transparent feature of the test pattern. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-02-18media: ov5640: Add register definition for test pattern registerChen-Yu Tsai1-2/+22
The OV5640 can generate many types of test patterns, some with additional modifiers, such as a rolling bar, or gamma gradients. Add the bit definitions for all bits in the test pattern register, and use them to compose the values to be written to the register. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-02-18media: ov5640: Move test_pattern_menu before ov5640_set_ctrl_test_patternChen-Yu Tsai1-5/+5
The OV5640 has many options for generating test patterns. Unfortunately there is only one V4L2 control for it. Thus the driver would need to list some or all combinations. Move the test_pattern_menu list before the ov5640_set_ctrl_test_pattern function that programs the hardware. This would allow us to add a matching list of values to program into the hardware, while keeping the two lists together for ease of maintenance. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-01-16media: ov5640: Add RAW bayer format supportLoic Poulain1-12/+46
OV5640 sensor supports raw image output (bayer). Configure ISP mux/format registers accordingly. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Remove duplicate auto-exposure setupMaxime Ripard1-1/+1
The autoexposure setup in the 1080p init array is redundant with the default value of the sensor. Remove it. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Add 60 fps supportMaxime Ripard1-4/+16
Now that we have everything in place to compute the clock rate at runtime, we can enable the 60fps framerate for the mode we tested it with. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Make the FPS clamping / rounding more extendableMaxime Ripard1-12/+15
The current code uses an algorithm to clamp the FPS values and round them to the closest supported one that isn't really allows to be extended to more than two values. Rework it a bit to make it much easier to extend the amount of FPS options we support. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Make the return rate type more explicitMaxime Ripard1-4/+4
In the ov5640_try_frame_interval function, the ret variable actually holds the frame rate index to use, which is represented by the enum ov5640_frame_rate in the driver. Make it more obvious. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Enhance FPS handlingMaxime Ripard1-255/+51
Now that we have moved the clock generation logic out of the bytes array, these arrays are identical between the 15fps and 30fps variants. Remove the duplicate entries, and convert the code accordingly. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Remove pixel clock ratesMaxime Ripard1-20/+1
The pixel clock rates were introduced to report the initially static clock rate. Since this is now handled dynamically, we can remove them entirely. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Compute the clock rate at runtimeMaxime Ripard1-1/+2
The clock rate, while hardcoded until now, is actually a function of the resolution, framerate and bytes per pixel. Now that we have an algorithm to adjust our clock rate, we can select it dynamically when we change the mode. This changes a bit the clock rate being used, with the following effect: +------+------+------+------+-----+-----------------+----------------+-----------+ | Hact | Vact | Htot | Vtot | FPS | Hardcoded clock | Computed clock | Deviation | +------+------+------+------+-----+-----------------+----------------+-----------+ | 640 | 480 | 1896 | 1080 | 15 | 56000000 | 61430400 | 8.84 % | | 640 | 480 | 1896 | 1080 | 30 | 112000000 | 122860800 | 8.84 % | | 1024 | 768 | 1896 | 1080 | 15 | 56000000 | 61430400 | 8.84 % | | 1024 | 768 | 1896 | 1080 | 30 | 112000000 | 122860800 | 8.84 % | | 320 | 240 | 1896 | 984 | 15 | 56000000 | 55969920 | 0.05 % | | 320 | 240 | 1896 | 984 | 30 | 112000000 | 111939840 | 0.05 % | | 176 | 144 | 1896 | 984 | 15 | 56000000 | 55969920 | 0.05 % | | 176 | 144 | 1896 | 984 | 30 | 112000000 | 111939840 | 0.05 % | | 720 | 480 | 1896 | 984 | 15 | 56000000 | 55969920 | 0.05 % | | 720 | 480 | 1896 | 984 | 30 | 112000000 | 111939840 | 0.05 % | | 720 | 576 | 1896 | 984 | 15 | 56000000 | 55969920 | 0.05 % | | 720 | 576 | 1896 | 984 | 30 | 112000000 | 111939840 | 0.05 % | | 1280 | 720 | 1892 | 740 | 15 | 42000000 | 42002400 | 0.01 % | | 1280 | 720 | 1892 | 740 | 30 | 84000000 | 84004800 | 0.01 % | | 1920 | 1080 | 2500 | 1120 | 15 | 84000000 | 84000000 | 0.00 % | | 1920 | 1080 | 2500 | 1120 | 30 | 168000000 | 168000000 | 0.00 % | | 2592 | 1944 | 2844 | 1944 | 15 | 84000000 | 165862080 | 49.36 % | +------+------+------+------+-----+-----------------+----------------+-----------+ Only the 640x480, 1024x768 and 2592x1944 modes are significantly affected by the new formula. In this case, 640x480 and 1024x768 are actually fixed by this change. Indeed, the sensor was sending data at, for example, 27.33fps instead of 30fps. This is -9%, which is roughly what we're seeing in the array. Testing these modes with the new clock setup actually fix that error, and data are now sent at around 30fps. 2592x1944, on the other hand, is probably due to the fact that this mode can only be used using MIPI-CSI2, in a two lane mode, and never really tested with a DVP bus. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Remove redundant register setupMaxime Ripard1-10/+0
The MIPI divider is also cleared as part of the clock setup sequence, so we can remove that code. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Remove redundant definesMaxime Ripard1-5/+2
The OV5640_SCLK2X_ROOT_DIVIDER_DEFAULT and OV5640_SCLK_ROOT_DIVIDER_DEFAULT defines represent exactly the same setup, and are at the same value, than the more consistent with the rest of the driver OV5640_SCLK2X_ROOT_DIV and OV5640_SCLK_ROOT_DIV. Remove them. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Remove the clocks registers initializationMaxime Ripard1-24/+22
Part of the hardcoded initialization sequence is to set up the proper clock dividers. However, this is now done dynamically through proper code and as such, the static one is now redundant. Let's remove it. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Adjust the clock based on the expected rateMaxime Ripard1-1/+364
The clock structure for the PCLK is quite obscure in the documentation, and was hardcoded through the bytes array of each and every mode. This is troublesome, since we cannot adjust it at runtime based on other parameters (such as the number of bytes per pixel), and we can't support either framerates that have not been used by the various vendors, since we don't have the needed initialization sequence. We can however understand how the clock tree works, and then implement some functions to derive the various parameters from a given rate. And now that those parameters are calculated at runtime, we can remove them from the initialization sequence. The modes also gained a new parameter which is the clock that they are running at, from the register writes they were doing, so for now the switch to the new algorithm should be transparent. Co-Developed-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Tested-by: Adam Ford <aford173@gmail.com> #imx6dq Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-12-05media: ov5640: Fix set format regressionJacopo Mondi1-9/+8
The set_fmt operations updates the sensor format only when the image format is changed. When only the image sizes gets changed, the format do not get updated causing the sensor to always report the one that was previously in use. Without this patch, updating frame size only fails: [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:srgb xfer:srgb ...] With this patch applied: [fmt:UYVY8_2X8/1024x768@1/30 field:none colorspace:srgb xfer:srgb ...] Fixes: 6949d864776e ("media: ov5640: do not change mode if format or frame interval is unchanged") Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Adam Ford <aford173@gmail.com> #imx6 w/ CSI2 interface on 4.19.6 and 4.20-RC5 Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-11-23media: ov5640: support log_status ioctl and event interfaceAkinobu Mita1-1/+6
This adds log_status ioctl and event interface for ov5640's v4l2 controls. Cc: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-10-05media: ov5640: fix framerate updateHugues Fruchet1-3/+4
Changing framerate right before streamon had no effect, the new framerate value was taken into account only at next streamon, fix this. Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-10-04media: v4l: mediabus: Recognise CSI-2 D-PHY and C-PHYSakari Ailus1-3/+3
The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media bus enum. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-10-03media: ov5640: use JPEG mode 3 for 720pHugues Fruchet1-1/+1
Change 720p JPEG mode to mode 3 as per other resolutions. Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-08-24 18:32:38 +0000