| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull core block layer updates from Jens Axboe:
"This is the main pull request for block storage for 4.15-rc1.
Nothing out of the ordinary in here, and no API changes or anything
like that. Just various new features for drivers, core changes, etc.
In particular, this pull request contains:
- A patch series from Bart, closing the whole on blk/scsi-mq queue
quescing.
- A series from Christoph, building towards hidden gendisks (for
multipath) and ability to move bio chains around.
- NVMe
- Support for native multipath for NVMe (Christoph).
- Userspace notifications for AENs (Keith).
- Command side-effects support (Keith).
- SGL support (Chaitanya Kulkarni)
- FC fixes and improvements (James Smart)
- Lots of fixes and tweaks (Various)
- bcache
- New maintainer (Michael Lyle)
- Writeback control improvements (Michael)
- Various fixes (Coly, Elena, Eric, Liang, et al)
- lightnvm updates, mostly centered around the pblk interface
(Javier, Hans, and Rakesh).
- Removal of unused bio/bvec kmap atomic interfaces (me, Christoph)
- Writeback series that fix the much discussed hundreds of millions
of sync-all units. This goes all the way, as discussed previously
(me).
- Fix for missing wakeup on writeback timer adjustments (Yafang
Shao).
- Fix laptop mode on blk-mq (me).
- {mq,name} tupple lookup for IO schedulers, allowing us to have
alias names. This means you can use 'deadline' on both !mq and on
mq (where it's called mq-deadline). (me).
- blktrace race fix, oopsing on sg load (me).
- blk-mq optimizations (me).
- Obscure waitqueue race fix for kyber (Omar).
- NBD fixes (Josef).
- Disable writeback throttling by default on bfq, like we do on cfq
(Luca Miccio).
- Series from Ming that enable us to treat flush requests on blk-mq
like any other request. This is a really nice cleanup.
- Series from Ming that improves merging on blk-mq with schedulers,
getting us closer to flipping the switch on scsi-mq again.
- BFQ updates (Paolo).
- blk-mq atomic flags memory ordering fixes (Peter Z).
- Loop cgroup support (Shaohua).
- Lots of minor fixes from lots of different folks, both for core and
driver code"
* 'for-4.15/block' of git://git.kernel.dk/linux-block: (294 commits)
nvme: fix visibility of "uuid" ns attribute
blk-mq: fixup some comment typos and lengths
ide: ide-atapi: fix compile error with defining macro DEBUG
blk-mq: improve tag waiting setup for non-shared tags
brd: remove unused brd_mutex
blk-mq: only run the hardware queue if IO is pending
block: avoid null pointer dereference on null disk
fs: guard_bio_eod() needs to consider partitions
xtensa/simdisk: fix compile error
nvme: expose subsys attribute to sysfs
nvme: create 'slaves' and 'holders' entries for hidden controllers
block: create 'slaves' and 'holders' entries for hidden gendisks
nvme: also expose the namespace identification sysfs files for mpath nodes
nvme: implement multipath access to nvme subsystems
nvme: track shared namespaces
nvme: introduce a nvme_ns_ids structure
nvme: track subsystems
block, nvme: Introduce blk_mq_req_flags_t
block, scsi: Make SCSI quiesce and resume work reliably
block: Add the QUEUE_FLAG_PREEMPT_ONLY request queue flag
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.15:
API:
- Disambiguate EBUSY when queueing crypto request by adding ENOSPC.
This change touches code outside the crypto API.
- Reset settings when empty string is written to rng_current.
Algorithms:
- Add OSCCA SM3 secure hash.
Drivers:
- Remove old mv_cesa driver (replaced by marvell/cesa).
- Enable rfc3686/ecb/cfb/ofb AES in crypto4xx.
- Add ccm/gcm AES in crypto4xx.
- Add support for BCM7278 in iproc-rng200.
- Add hash support on Exynos in s5p-sss.
- Fix fallback-induced error in vmx.
- Fix output IV in atmel-aes.
- Fix empty GCM hash in mediatek.
Others:
- Fix DoS potential in lib/mpi.
- Fix potential out-of-order issues with padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
lib/mpi: call cond_resched() from mpi_powm() loop
crypto: stm32/hash - Fix return issue on update
crypto: dh - Remove pointless checks for NULL 'p' and 'g'
crypto: qat - Clean up error handling in qat_dh_set_secret()
crypto: dh - Don't permit 'key' or 'g' size longer than 'p'
crypto: dh - Don't permit 'p' to be 0
crypto: dh - Fix double free of ctx->p
hwrng: iproc-rng200 - Add support for BCM7278
dt-bindings: rng: Document BCM7278 RNG200 compatible
crypto: chcr - Replace _manual_ swap with swap macro
crypto: marvell - Add a NULL entry at the end of mv_cesa_plat_id_table[]
hwrng: virtio - Virtio RNG devices need to be re-registered after suspend/resume
crypto: atmel - remove empty functions
crypto: ecdh - remove empty exit()
MAINTAINERS: update maintainer for qat
crypto: caam - remove unused param of ctx_map_to_sec4_sg()
crypto: caam - remove unneeded edesc zeroization
crypto: atmel-aes - Reset the controller before each use
crypto: atmel-aes - properly set IV after {en,de}crypt
hwrng: core - Reset user selected rng by writing "" to rng_current
...
|
|
Conflicts:
include/linux/compiler-clang.h
include/linux/compiler-gcc.h
include/linux/compiler-intel.h
include/uapi/linux/stddef.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
dm-verity is starting async. crypto ops and waiting for them to complete.
Move it over to generic code doing the same.
This also avoids a future potential data coruption bug created
by the use of wait_for_completion_interruptible() without dealing
correctly with an interrupt aborting the wait prior to the
async op finishing, should this code ever move to a context
where signals are not masked.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mutex_destroy does nothing most of time, but it's better to call
it to make the code future proof and it also has some meaning
for like mutex debug.
As Coly pointed out in a previous review, bcache_exit() may not be
able to handle all the references properly if userspace registers
cache and backing devices right before bch_debug_init runs and
bch_debug_init failes later. So not exposing userspace interface
until everything is ready to avoid that issue.
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Reviewed-by: Eric Wheeler <bcache@linux.ewheeler.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, Cache missed IOs are identified by s->cache_miss, but actually,
there are many situations that missed IOs are not assigned a value for
s->cache_miss in cached_dev_cache_miss(), for example, a bypassed IO
(s->iop.bypass = 1), or the cache_bio allocate failed. In these situations,
it will go to out_put or out_submit, and s->cache_miss is null, which leads
bch_mark_cache_accounting() to treat this IO as a hit IO.
[ML: applied by 3-way merge]
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
bucket_in_use is updated in gc thread which triggered by invalidating or
writing sectors_to_gc dirty data, It's a long interval. Therefore, when we
use it to compare with the threshold, it is often not timely, which leads
to inaccurate judgment and often results in bucket depletion.
We have send a patch before, by the means of updating bucket_in_use
periodically In gc thread, which Coly thought that would lead high
latency, In this patch, we add avail_nbuckets to record the count of
available buckets, and we calculate bucket_in_use when alloc or free
bucket in real time.
[edited by ML: eliminated some whitespace errors]
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable cached_dev.count is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When bcache does read I/Os, for example in writeback or writethrough mode,
if a read request on cache device is failed, bcache will try to recovery
the request by reading from cached device. If the data on cached device is
not synced with cache device, then requester will get a stale data.
For critical storage system like database, providing stale data from
recovery may result an application level data corruption, which is
unacceptible.
With this patch, for a failed read request in writeback or writethrough
mode, recovery a recoverable read request only happens when cache device
is clean. That is to say, all data on cached device is up to update.
For other cache modes in bcache, read request will never hit
cached_dev_read_error(), they don't need this patch.
Please note, because cache mode can be switched arbitrarily in run time, a
writethrough mode might be switched from a writeback mode. Therefore
checking dc->has_data in writethrough mode still makes sense.
Changelog:
V4: Fix parens error pointed by Michael Lyle.
v3: By response from Kent Oversteet, he thinks recovering stale data is a
bug to fix, and option to permit it is unnecessary. So this version
the sysfs file is removed.
v2: rename sysfs entry from allow_stale_data_on_failure to
allow_stale_data_on_failure, and fix the confusing commit log.
v1: initial patch posted.
[small change to patch comment spelling by mlyle]
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reported-by: Arne Wolf <awolf@lenovo.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Nix <nix@esperi.org.uk>
Cc: Kai Krakow <hurikhan77@gmail.com>
Cc: Eric Wheeler <bcache@lists.ewheeler.net>
Cc: Junhui Tang <tang.junhui@zte.com.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
to READ_ONCE()/WRITE_ONCE()
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't currently harmful.
However, for some features it is necessary to instrument reads and
writes separately, which is not possible with ACCESS_ONCE(). This
distinction is critical to correct operation.
It's possible to transform the bulk of kernel code using the Coccinelle
script below. However, this doesn't pick up some uses, including those
in dm-integrity.c. As a preparatory step, this patch converts the driver
to use {READ,WRITE}_ONCE() consistently.
At the same time, this patch adds the missing include of
<linux/compiler.h> necessary for the {READ,WRITE}_ONCE() definitions.
----
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-1-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
READ_ONCE() now has an implicit smp_read_barrier_depends() call, so it
can be used instead of lockless_dereference() without any change in
semantics.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1508840570-22169-4-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Sorry this got through to linux-block, was detected by the kbuilds test
robot. NSEC_PER_SEC is a long constant; 2.5 * 10^9 doesn't fit in a
signed long constant.
Fixes: e41166c5c44e ("bcache: writeback rate shouldn't artifically clamp")
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The use of the union reduces the size of closure struct by taking advantage
of the current size of its members. The offset of func in work_struct
equals the size of the first three members, so that work.work_func will
just reference the forth member - fn.
This is smart but dangerous. It can be broken if work_struct or the other
structs get changed, and can be a bit difficult to debug.
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The time spent searching for things to write back "counts" for the
actual rate achieved, so don't flush the accumulated rate with each
chunk.
This will maintain better fidelity to user-commanded rates, but it
may slightly increase the burstiness of writeback. The writeback
lock needs improvement to help mitigate this.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The previous code artificially limited writeback rate to 1000000
blocks/second (NSEC_PER_MSEC), which is a rate that can be met on fast
hardware. The rate limiting code works fine (though with decreased
precision) up to 3 orders of magnitude faster, so use NSEC_PER_SEC.
Additionally, ensure that uint32_t is used as a type for rate throughout
the rate management so that type checking/clamp_t can work properly.
bch_next_delay should be rewritten for increased precision and better
handling of high rates and long sleep periods, but this is adequate for
now.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reported-by: Coly Li <colyli@suse.de>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This works in conjunction with the new PI controller. Currently, in
real-world workloads, the rate controller attempts to write back 1
sector per second. In practice, these minimum-rate writebacks are
between 4k and 60k in test scenarios, since bcache aggregates and
attempts to do contiguous writes and because filesystems on top of
bcachefs typically write 4k or more.
Previously, bcache used to guarantee to write at least once per second.
This means that the actual writeback rate would exceed the configured
amount by a factor of 8-120 or more.
This patch adjusts to be willing to sleep up to 2.5 seconds, and to
target writing 4k/second. On the smallest writes, it will sleep 1
second like before, but many times it will sleep longer and load the
backing device less. This keeps the loading on the cache and backing
device related to writeback more consistent when writing back at low
rates.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
bcache uses a control system to attempt to keep the amount of dirty data
in cache at a user-configured level, while not responding excessively to
transients and variations in write rate. Previously, the system was a
PD controller; but the output from it was integrated, turning the
Proportional term into an Integral term, and turning the Derivative term
into a crude Proportional term. Performance of the controller has been
uneven in production, and it has tended to respond slowly, oscillate,
and overshoot.
This patch set replaces the current control system with an explicit PI
controller and tuning that should be correct for most hardware. By
default, it attempts to write at a rate that would retire 1/40th of the
current excess blocks per second. An integral term in turn works to
remove steady state errors.
IMO, this yields benefits in simplicity (removing weighted average
filtering, etc) and system performance.
Another small change is a tunable parameter is introduced to allow the
user to specify a minimum rate at which dirty blocks are retired.
There is a slight difference from earlier versions of the patch in
integral handling to prevent excessive negative integral windup.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If an IO operation fails, and we didn't successfully read data from the
cache, don't writeback invalid/partial data to the backing disk.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Parameter bio is no longer used, clean it.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Flag for bypass if the IO is for read-ahead or background, unless the
read-ahead request is for metadata (eg, from gfs2).
Bypass if:
bio->bi_opf & (REQ_RAHEAD|REQ_BACKGROUND) &&
!(bio->bi_opf & REQ_META))
Writeback if:
op_is_sync(bio->bi_opf) ||
bio->bi_opf & (REQ_META|REQ_PRIO)
Signed-off-by: Eric Wheeler <bcache@linux.ewheeler.net>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
set_capacity() has been called in bcache_device_init(),
remove the redundant one.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Reviewed-by: Eric Wheeler <bcache@linux.ewheeler.net>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Current partition support of bcache is confusing and buggy. It tries to
trace non-continuous device minor numbers by an ida bit string, and
mistakenly mixed bcache device index with minor numbers. This design
generates several negative results,
- Index of bcache device name is not consecutive under /dev/. If there are
3 bcache devices, they name will be,
/dev/bcache0, /dev/bcache16, /dev/bcache32
Only bcache code indexes bcache device name is such an interesting way.
- First minor number of each bcache device is traced by ida bit string.
One bcache device will occupy 16 bits, this is not a good idea. Indeed
only one bit is enough.
- Because minor number and bcache device index are mixed, a device index
is allocated by ida_simple_get(), but an first minor number is sent into
ida_simple_remove() to release the device. It confused original author
too.
Root cause of the above errors is, bcache code should not handle device
minor numbers at all! A standard process to support multiple partitions in
Linux kernel is,
- Device driver provides major device number, and indexes multiple device
instances.
- Device driver does not allocat nor trace device minor number, only
provides a first minor number of a given device instance, and sets how
many minor numbers (paritions) the device instance may have.
All rested stuffs are handled by block layer code, most of the details can
be found from block/{genhd, partition-generic}.c files.
This patch re-writes multiple partitions support for bcache. It makes
whole things to be more clear, and uses ida bit string in a more efficeint
way.
- Ida bit string only traces bcache device index, not minor number. For a
bcache device with 128 partitions, only one bit in ida bit string is
enough.
- Device minor number and device index are separated in concept. Device
index is used for /dev node naming, and ida bit string trace. Minor
number is calculated from device index and only used to initialize
first_minor of a bcache device.
- It does not follow any standard for 16 partitions on a bcache device.
This patch sets 128 partitions on single bcache device at max, this is
the limitation from GPT (GUID Partition Table) and supported by fdisk.
Considering a typical device minor number is 20 bits width, each bcache
device may have 128 partitions (7 bits), there can be 8192 bcache devices
existing on system. For most common deployment for a single server in
now days, it should be enough.
[minor spelling fixes in commit message by Michael Lyle]
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Eric Wheeler <bcache@lists.ewheeler.net>
Cc: Junhui Tang <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Code comments in alloc.c:bch_alloc_sectors() mentions a function
name find_data_bucket(), the correct function name should be
pick_data_bucket() indeed. bch_alloc_sectors() is a quite important
function in bcache allocation code, fixing the typo may help
other people to have less confusion.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In bcache code, sysfs entries are created before all resources get
allocated, e.g. allocation thread of a cache set.
There is posibility for NULL pointer deference if a resource is accessed
but which is not initialized yet. Indeed Jorg Bornschein catches one on
cache set allocation thread and gets a kernel oops.
The reason for this bug is, when bch_bucket_alloc() is called during
cache set registration and attaching, ca->alloc_thread is not properly
allocated and initialized yet, call wake_up_process() on ca->alloc_thread
triggers NULL pointer deference failure. A simple and fast fix is, before
waking up ca->alloc_thread, checking whether it is allocated, and only
wake up ca->alloc_thread when it is not NULL.
Signed-off-by: Coly Li <colyli@suse.de>
Reported-by: Jorg Bornschein <jb@capsec.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fixes below error with clang:
../drivers/md/bcache/sysfs.c:759:3: error: function definition is not allowed here
{ return *((uint16_t *) r) - *((uint16_t *) l); }
^
../drivers/md/bcache/sysfs.c:789:32: error: use of undeclared identifier 'cmp'
sort(p, n, sizeof(uint16_t), cmp, NULL);
^
2 errors generated.
v2:
rename function to __bch_cache_cmp
Signed-off-by: Peter Foley <pefoley2@pefoley.com>
Reviewed-by: Coly Li <colyli@suse.de>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull block fixes from Jens Axboe:
"A collection of fixes for this series. This contains:
- NVMe pull request from Christoph, one uuid attribute fix, and one
fix for the controller memory buffer address for remapped BARs.
- use-after-free fix for bsg, from Benjamin Block.
- bcache race/use-after-free fix for a list traversal, fixing a
regression in this merge window. From Coly Li.
- null_blk change configfs dependency change from a 'depends' to a
'select'. This is a change from this merge window as well. From me.
- nbd signal fix from Josef, fixing a regression introduced with the
status code changes.
- nbd MAINTAINERS mailing list entry update.
- blk-throttle stall fix from Joseph Qi.
- blk-mq-debugfs fix from Omar, fixing an issue where we don't
register the IO scheduler debugfs directory, if the driver is
loaded with it. Only shows up if you switch through the sysfs
interface"
* 'for-linus' of git://git.kernel.dk/linux-block:
bsg-lib: fix use-after-free under memory-pressure
nvme-pci: Use PCI bus address for data/queues in CMB
blk-mq-debugfs: fix device sched directory for default scheduler
null_blk: change configfs dependency to select
blk-throttle: fix possible io stall when upgrade to max
MAINTAINERS: update list for NBD
nbd: fix -ERESTARTSYS handling
nvme: fix visibility of "uuid" ns attribute
bcache: use llist_for_each_entry_safe() in __closure_wake_up()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix for the alignment of the event number reported at the
end of the 'DM_LIST_DEVICES' ioctl.
- a couple stable fixes for the DM crypt target.
- a DM raid health status reporting fix.
* tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: fix incorrect status output at the end of a "recover" process
dm crypt: reject sector_size feature if device length is not aligned to it
dm crypt: fix memory leak in crypt_ctr_cipher_old()
dm ioctl: fix alignment of event number in the device list
|
|
We already have a queue_is_rq_based helper to check if a request_queue
is request based, so we can remove the flag for it.
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There are three important fields that indicate the overall health and
status of an array: dev_health, sync_ratio, and sync_action. They tell
us the condition of the devices in the array, and the degree to which
the array is synchronized.
This commit fixes a condition that is reported incorrectly. When a member
of the array is being rebuilt or a new device is added, the "recover"
process is used to synchronize it with the rest of the array. When the
process is complete, but the sync thread hasn't yet been reaped, it is
possible for the state of MD to be:
mddev->recovery = [ MD_RECOVERY_RUNNING MD_RECOVERY_RECOVER MD_RECOVERY_DONE ]
curr_resync_completed = <max dev size> (but not MaxSector)
and all rdevs to be In_sync.
This causes the 'array_in_sync' output parameter that is passed to
rs_get_progress() to be computed incorrectly and reported as 'false' --
or not in-sync. This in turn causes the dev_health status characters to
be reported as all 'a', rather than the proper 'A'.
This can cause erroneous output for several seconds at a time when tools
will want to be checking the condition due to events that are raised at
the end of a sync process. Fix this by properly calculating the
'array_in_sync' return parameter in rs_get_progress().
Also, remove an unnecessary intermediate 'recovery_cp' variable in
rs_get_progress().
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
If a crypt mapping uses optional sector_size feature, additional
restrictions to mapped device segment size must be applied in
constructor, otherwise the device activation will fail later.
Fixes: 8f0009a225 ("dm crypt: optionally support larger encryption sector size")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Instead of adding weird retry logic in that function, utilize
__GFP_NOFAIL to ensure that the vm takes care of handling any
potential retries appropriately. This means we don't have to
call free_more_memory() from here.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fix memory leak of cipher_api.
Fixes: 33d2f09fcb35 (dm crypt: introduce new format of cipher with "capi:" prefix)
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
static checker reports a potential integer overflow. Cap the worker count to
avoid the overflow.
Reported:-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
raid_map calls pers->make_request, which missed the suspend check. Fix it with
the new md_handle_request API.
Fix: cc27b0c78c79(md: fix deadlock between mddev_suspend() and md_write_start())
Cc: Heinz Mauelshagen <heinzm@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
md_submit_flush_data calls pers->make_request, which missed the suspend check.
Fix it with the new md_handle_request API.
Reported-by: Nate Dailey <nate.dailey@stratus.com>
Tested-by: Nate Dailey <nate.dailey@stratus.com>
Fix: cc27b0c78c79(md: fix deadlock between mddev_suspend() and md_write_start())
Cc: stable@vger.kernel.org
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
With commit cc27b0c78c79, pers->make_request could bail out without handling
the bio. If that happens, we should retry. The commit fixes md_make_request
but not other call sites. Separate the request handling part, so other call
sites can use it.
Reported-by: Nate Dailey <nate.dailey@stratus.com>
Fix: cc27b0c78c79(md: fix deadlock between mddev_suspend() and md_write_start())
Cc: stable@vger.kernel.org
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Commit 09b3efec ("bcache: Don't reinvent the wheel but use existing llist
API") replaces the following while loop by llist_for_each_entry(),
-
- while (reverse) {
- cl = container_of(reverse, struct closure, list);
- reverse = llist_next(reverse);
-
+ llist_for_each_entry(cl, reverse, list) {
closure_set_waiting(cl, 0);
closure_sub(cl, CLOSURE_WAITING + 1);
}
This modification introduces a potential race by iterating a corrupted
list. Here is how it happens.
In the above modification, closure_sub() may wake up a process which is
waiting on reverse list. If this process decides to wait again by calling
closure_wait(), its cl->list will be added to another wait list. Then
when llist_for_each_entry() continues to iterate next node, it will travel
on another new wait list which is added in closure_wait(), not the
original reverse list in __closure_wake_up(). It is more probably to
happen on UP machine because the waked up process may preempt the process
which wakes up it.
Use llist_for_each_entry_safe() will fix the issue, the safe version fetch
next node before waking up a process. Then the copy of next node will make
sure list iteration stays on original reverse list.
Fixes: 09b3efec81de ("bcache: Don't reinvent the wheel but use existing llist API")
Signed-off-by: Coly Li <colyli@suse.de>
Reported-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Byungchul Park <byungchul.park@lge.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The size of struct dm_name_list is different on 32-bit and 64-bit
kernels (so "(nl + 1)" differs between 32-bit and 64-bit kernels).
This mismatch caused some harmless difference in padding when using 32-bit
or 64-bit kernel. Commit 23d70c5e52dd ("dm ioctl: report event number in
DM_LIST_DEVICES") added reporting event number in the output of
DM_LIST_DEVICES_CMD. This difference in padding makes it impossible for
userspace to determine the location of the event number (the location
would be different when running on 32-bit and 64-bit kernels).
Fix the padding by using offsetof(struct dm_name_list, name) instead of
sizeof(struct dm_name_list) to determine the location of entries.
Also, the ioctl version number is incremented to 37 so that userspace
can use the version number to determine that the event number is present
and correctly located.
In addition, a global event is now raised when a DM device is created,
removed, renamed or when table is swapped, so that the user can monitor
for device changes.
Reported-by: Eugene Syromiatnikov <esyr@redhat.com>
Fixes: 23d70c5e52dd ("dm ioctl: report event number in DM_LIST_DEVICES")
Cc: stable@vger.kernel.org # 4.13
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Pull MD fixes from Shaohua Li:
"Two small patches to fix long-lived raid5 stripe batch bugs, one from
Dennis and the other from me"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/raid5: preserve STRIPE_ON_UNPLUG_LIST in break_stripe_batch_list
md/raid5: fix a race condition in stripe batch
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Some request-based DM core and DM multipath fixes and cleanups
- Constify a few variables in DM core and DM integrity
- Add bufio optimization and checksum failure accounting to DM
integrity
- Fix DM integrity to avoid checking integrity of failed reads
- Fix DM integrity to use init_completion
- A couple DM log-writes target fixes
- Simplify DAX flushing by eliminating the unnecessary flush
abstraction that was stood up for DM's use.
* tag 'for-4.14/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dax: remove the pmem_dax_ops->flush abstraction
dm integrity: use init_completion instead of COMPLETION_INITIALIZER_ONSTACK
dm integrity: make blk_integrity_profile structure const
dm integrity: do not check integrity for failed read operations
dm log writes: fix >512b sectorsize support
dm log writes: don't use all the cpu while waiting to log blocks
dm ioctl: constify ioctl lookup table
dm: constify argument arrays
dm integrity: count and display checksum failures
dm integrity: optimize writing dm-bufio buffers that are partially changed
dm rq: do not update rq partially in each ending bio
dm rq: make dm-sq requeuing behavior consistent with dm-mq behavior
dm mpath: complain about unsupported __multipath_map_bio() return values
dm mpath: avoid that building with W=1 causes gcc 7 to complain about fall-through
|
|
Commit abebfbe2f731 ("dm: add ->flush() dax operation support") is
buggy. A DM device may be composed of multiple underlying devices and
all of them need to be flushed. That commit just routes the flush
request to the first device and ignores the other devices.
It could be fixed by adding more complex logic to the device mapper. But
there is only one implementation of the method pmem_dax_ops->flush - that
is pmem_dax_flush() - and it calls arch_wb_cache_pmem(). Consequently, we
don't need the pmem_dax_ops->flush abstraction at all, we can call
arch_wb_cache_pmem() directly from dax_flush() because dax_dev->ops->flush
can't ever reach anything different from arch_wb_cache_pmem().
It should be also pointed out that for some uses of persistent memory it
is needed to flush only a very small amount of data (such as 1 cacheline),
and it would be overkill if we go through that device mapper machinery for
a single flushed cache line.
Fix this by removing the pmem_dax_ops->flush abstraction and call
arch_wb_cache_pmem() directly from dax_flush(). Also, remove the device
mapper code that forwards the flushes.
Fixes: abebfbe2f731 ("dm: add ->flush() dax operation support")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The new lockdep support for completions causeed the stack usage
in dm-integrity to explode, in case of write_journal from 504 bytes
to 1120 (using arm gcc-7.1.1):
drivers/md/dm-integrity.c: In function 'write_journal':
drivers/md/dm-integrity.c:827:1: error: the frame size of 1120 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
The problem is that not only the size of 'struct completion' grows
significantly, but we end up having multiple copies of it on the stack
when we assign it from a local variable after the initial declaration.
COMPLETION_INITIALIZER_ONSTACK() is the right thing to use when we
want to declare and initialize a completion on the stack. However,
this driver doesn't do that and instead initializes the completion
just before it is used.
In this case, init_completion() does the same thing more efficiently,
and drops the stack usage for the function above down to 496 bytes.
While the other functions in this file are not bad enough to cause
a warning, they benefit equally from the change, so I do the change
across the entire file. In the one place where we reuse a completion,
I picked the cheaper reinit_completion() over init_completion().
Fixes: cd8084f91c02 ("locking/lockdep: Apply crossrelease to completions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Make this structure const as it is only stored in the profile field of a
blk_integrity structure. This field is of type const, so make structure
as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Even though read operations fail, dm_integrity_map_continue() calls
integrity_metadata() to check integrity. In this case, just complete
these.
This also makes it so read I/O errors do not generate integrity warnings
in the kernel log.
Cc: stable@vger.kernel.org
Signed-off-by: Hyunchul Lee <cheol.lee@lge.com>
Acked-by: Milan Broz <gmazyland@gmail.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
512b sectors vs device's physical sectorsize was not maintained
consistently and as such the support for >512b sector devices has bugs.
The log metadata expects native sectorsize but 512b sectors were being
stored. Also, device's sectorsize was assumed when assigning the
bi_sector for blocks that were being logged.
Fix this up by adding two helpers to convert between bio and dev
sectors, and use these in the appropriate places to fix the problem and
make it clear which units go where. Doing so allows dm-log-writes use
with 4k devices.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The check to see if the logging kthread needs to go to sleep is wrong,
it checks lc->pending_blocks, which will be non-0 if there are any
blocks that are pending, whether they are ready to be logged or not.
What we really want is to go to sleep until it's time to log blocks, so
change this check so we do actually go to sleep in between flushes.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Pull followup block layer updates from Jens Axboe:
"I ended up splitting the main pull request for this series into two,
mainly because of clashes between NVMe fixes that went into 4.13 after
the for-4.14 branches were split off. This pull request is mostly
NVMe, but not exclusively. In detail, it contains:
- Two pull request for NVMe changes from Christoph. Nothing new on
the feature front, basically just fixes all over the map for the
core bits, transport, rdma, etc.
- Series from Bart, cleaning up various bits in the BFQ scheduler.
- Series of bcache fixes, which has been lingering for a release or
two. Coly sent this in, but patches from various people in this
area.
- Set of patches for BFQ from Paolo himself, updating both
documentation and fixing some corner cases in performance.
- Series from Omar, attempting to now get the 4k loop support
correct. Our confidence level is higher this time.
- Series from Shaohua for loop as well, improving O_DIRECT
performance and fixing a use-after-free"
* 'for-4.14/block-postmerge' of git://git.kernel.dk/linux-block: (74 commits)
bcache: initialize dirty stripes in flash_dev_run()
loop: set physical block size to logical block size
bcache: fix bch_hprint crash and improve output
bcache: Update continue_at() documentation
bcache: silence static checker warning
bcache: fix for gc and write-back race
bcache: increase the number of open buckets
bcache: Correct return value for sysfs attach errors
bcache: correct cache_dirty_target in __update_writeback_rate()
bcache: gc does not work when triggering by manual command
bcache: Don't reinvent the wheel but use existing llist API
bcache: do not subtract sectors_to_gc for bypassed IO
bcache: fix sequential large write IO bypass
bcache: Fix leak of bdev reference
block/loop: remove unused field
block/loop: fix use after free
bfq: Use icq_to_bic() consistently
bfq: Suppress compiler warnings about comparisons
bfq: Check kstrtoul() return value
bfq: Declare local functions static
...
|
|
Pull MD updates from Shaohua Li:
"This update mainly fixes bugs:
- Make raid5 ppl support several ppl from Pawel
- Several raid5-cache bug fixes from Song
- Bitmap fixes from Neil and Me
- One raid1/10 regression fix since 4.12 from Me
- Other small fixes and cleanup"
* tag 'md/4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/bitmap: disable bitmap_resize for file-backed bitmaps.
raid5-ppl: Recovery support for multiple partial parity logs
md: Runtime support for multiple ppls
md/raid0: attach correct cgroup info in bio
lib/raid6: align AVX512 constants to 512 bits, not bytes
raid5: remove raid5_build_block
md/r5cache: call mddev_lock/unlock() in r5c_journal_mode_show
md: replace seq_release_private with seq_release
md: notify about new spare disk in the container
md/raid1/10: reset bio allocated from mempool
md/raid5: release/flush io in raid5_do_work()
md/bitmap: copy correct data for bitmap super
|
