summaryrefslogtreecommitdiffstats
path: root/drivers/md/raid5.c
AgeCommit message (Collapse)AuthorFilesLines
2020-10-08md/raid5: fix oops during stripe resizingSong Liu1-2/+2
KoWei reported crash during raid5 reshape: [ 1032.252932] Oops: 0002 [#1] SMP PTI [...] [ 1032.252943] RIP: 0010:memcpy_erms+0x6/0x10 [...] [ 1032.252947] RSP: 0018:ffffba1ac0c03b78 EFLAGS: 00010286 [ 1032.252949] RAX: 0000784ac0000000 RBX: ffff91bec3d09740 RCX: 0000000000001000 [ 1032.252951] RDX: 0000000000001000 RSI: ffff91be6781c000 RDI: 0000784ac0000000 [ 1032.252953] RBP: ffffba1ac0c03bd8 R08: 0000000000001000 R09: ffffba1ac0c03bf8 [ 1032.252954] R10: 0000000000000000 R11: 0000000000000000 R12: ffffba1ac0c03bf8 [ 1032.252955] R13: 0000000000001000 R14: 0000000000000000 R15: 0000000000000000 [ 1032.252958] FS: 0000000000000000(0000) GS:ffff91becf500000(0000) knlGS:0000000000000000 [ 1032.252959] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1032.252961] CR2: 0000784ac0000000 CR3: 000000031780a002 CR4: 00000000001606e0 [ 1032.252962] Call Trace: [ 1032.252969] ? async_memcpy+0x179/0x1000 [async_memcpy] [ 1032.252977] ? raid5_release_stripe+0x8e/0x110 [raid456] [ 1032.252982] handle_stripe_expansion+0x15a/0x1f0 [raid456] [ 1032.252988] handle_stripe+0x592/0x1270 [raid456] [ 1032.252993] handle_active_stripes.isra.0+0x3cb/0x5a0 [raid456] [ 1032.252999] raid5d+0x35c/0x550 [raid456] [ 1032.253002] ? schedule+0x42/0xb0 [ 1032.253006] ? schedule_timeout+0x10e/0x160 [ 1032.253011] md_thread+0x97/0x160 [ 1032.253015] ? wait_woken+0x80/0x80 [ 1032.253019] kthread+0x104/0x140 [ 1032.253022] ? md_start_sync+0x60/0x60 [ 1032.253024] ? kthread_park+0x90/0x90 [ 1032.253027] ret_from_fork+0x35/0x40 This is because cache_size_mutex was unlocked too early in resize_stripes, which races with grow_one_stripe() that grow_one_stripe() allocates a stripe with wrong pool_size. Fix this issue by unlocking cache_size_mutex after updating pool_size. Cc: <stable@vger.kernel.org> # v4.4+ Reported-by: KoWei Sung <winders@amazon.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-09-24md/raid5: reallocate page array after setting new stripe_sizeYufen Yu1-0/+20
When try to resize stripe_size, we also need to free old shared page array and allocate new. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-09-24md/raid5: resize stripe_head when reshape arrayYufen Yu1-0/+24
When reshape array, we try to reuse shared pages of old stripe_head, and allocate more for the new one if needed. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-09-24md/raid5: let multiple devices of stripe_head share pageYufen Yu1-2/+87
In current implementation, grow_buffers() uses alloc_page() to allocate the buffers for each stripe_head, i.e. allocate a page for each dev[i] in stripe_head. After setting stripe_size as a configurable value by writing sysfs entry, it means that we always allocate 64K buffers, but just use 4K of them when stripe_size is 4K in 64KB arm64. To avoid wasting memory, we try to let multiple sh->dev share one real page. That means, multiple sh->dev[i].page will point to the only page with different offset. Example of 64K PAGE_SIZE and 4K stripe_size as following: 64K PAGE_SIZE +---+---+---+---+------------------------------+ | | | | | | | | | | +-+-+-+-+-+-+-+-+------------------------------+ ^ ^ ^ ^ | | | +----------------------------+ | | | | | | +-------------------+ | | | | | | +----------+ | | | | | | +-+ | | | | | | | +-----+-----+------+-----+------+-----+------+------+ sh | offset(0) | offset(4K) | offset(8K) | offset(12K) | + +-----------+------------+------------+-------------+ +----> dev[0].page dev[1].page dev[2].page dev[3].page A new 'pages' array will be added into stripe_head to record shared page used by this stripe_head. Allocate them when grow_buffers() and free them when shrink_buffers(). After trying to share page, the users of sh->dev[i].page need to take care of the related page offset: page of issued bio and page passed to xor compution functions. But thanks for previous different page offset supported. Here, we just need to set correct dev[i].offset. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-09-24md/raid6: let async recovery function support different page offsetYufen Yu1-2/+2
For now, asynchronous raid6 recovery calculate functions are require common offset for pages. But, we expect them to support different page offset after introducing stripe shared page. Do that by simplily adding page offset where each page address are referred. Then, replace the old interface with the new ones in raid6 and raid6test. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-09-24md/raid6: let syndrome computor support different page offsetYufen Yu1-12/+24
For now, syndrome compute functions require common offset in the pages array. However, we expect them to support different offset when try to use shared page in the following. Simplily covert them by adding page offset where each page address are referred. Since the only caller of async_gen_syndrome() and async_syndrome_val() are in raid6, we don't want to reserve the old interface but modify the interface directly. After that, replacing old interfaces with new ones for raid6 and raid6test. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-09-24md/raid5: convert to new xor compution interfaceYufen Yu1-9/+34
We try to replace async_xor() and async_xor_val() with the new introduced interface async_xor_offs() and async_xor_val_offs() for raid456. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-09-24md/raid5: make async_copy_data() to support different page offsetYufen Yu1-3/+5
ops_run_biofill() and ops_run_biodrain() will call async_copy_data() to copy sh->dev[i].page from or to bio page. For now, it implies the offset of dev[i].page is 0. But we want to support different page offset in the following. Thus, pass page offset to these functions and replace 'page_offset' with 'page_offset + poff'. No functional change. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-09-24md/raid5: add a new member of offset into r5devYufen Yu1-11/+39
Add a new member of offset into struct r5dev. It indicates the offset of related dev[i].page. For now, since each device have a privated page, the value is always 0. Thus, we set offset as 0 when allcate page in grow_buffers() and resize_stripes(). To support following different page offset, we try to use the page offset rather than '0' directly for async_memcpy() and ops_run_io(). We try to support different page offset for xor compution functions in the following. To avoid repeatly allocate a new array each time, we add a memory region into scribble buffer to record offset. No functional change. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-09-24bdi: replace BDI_CAP_STABLE_WRITES with a queue and a sb flagChristoph Hellwig1-4/+4
The BDI_CAP_STABLE_WRITES is one of the few bits of information in the backing_dev_info shared between the block drivers and the writeback code. To help untangling the dependency replace it with a queue flag and a superblock flag derived from it. This also helps with the case of e.g. a file system requiring stable writes due to its own checksumming, but not forcing it on other users of the block device like the swap code. One downside is that we an't support the stable_pages_required bdi attribute in sysfs anymore. It is replaced with a queue attribute which also is writable for easier testing. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-09-24block: lift setting the readahead size into the block layerChristoph Hellwig1-12/+1
Drivers shouldn't really mess with the readahead size, as that is a VM concept. Instead set it based on the optimal I/O size by lifting the algorithm from the md driver when registering the disk. Also set bdi->io_pages there as well by applying the same scheme based on max_sectors. To ensure the limits work well for stacking drivers a new helper is added to update the readahead limits from the block limits, which is also called from disk_stack_limits. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Mike Snitzer <snitzer@redhat.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-09-24md: update the optimal I/O size on reshapeChristoph Hellwig1-2/+8
The raid5 and raid10 drivers currently update the read-ahead size, but not the optimal I/O size on reshape. To prepare for deriving the read-ahead size from the optimal I/O size make sure it is updated as well. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-by: Song Liu <song@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-08-28Merge tag 'block-5.9-2020-08-28' of git://git.kernel.dk/linux-blockLinus Torvalds1-2/+5
Pull block fixes from Jens Axboe: - nbd timeout fix (Hou) - device size fix for loop LOOP_CONFIGURE (Martijn) - MD pull from Song with raid5 stripe size fix (Yufen) * tag 'block-5.9-2020-08-28' of git://git.kernel.dk/linux-block: md/raid5: make sure stripe_size as power of two loop: Set correct device size when using LOOP_CONFIGURE nbd: restore default timeout when setting it to zero
2020-08-27md/raid5: make sure stripe_size as power of twoYufen Yu1-2/+5
Commit 3b5408b98e4d ("md/raid5: support config stripe_size by sysfs entry") make stripe_size as a configurable value. It just requires stripe_size as multiple of 4KB. In fact, we should make sure stripe_size as power of two. Otherwise, stripe_shift which is the result of ilog2 can not represent the real stripe_size. Then, stripe_hash() and stripe_hash_locks_hash() may get unexpected value. Fixes: 3b5408b98e4d ("md/raid5: support config stripe_size by sysfs entry") Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva1-2/+2
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-10Merge tag 'locking-urgent-2020-08-10' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull locking updates from Thomas Gleixner: "A set of locking fixes and updates: - Untangle the header spaghetti which causes build failures in various situations caused by the lockdep additions to seqcount to validate that the write side critical sections are non-preemptible. - The seqcount associated lock debug addons which were blocked by the above fallout. seqcount writers contrary to seqlock writers must be externally serialized, which usually happens via locking - except for strict per CPU seqcounts. As the lock is not part of the seqcount, lockdep cannot validate that the lock is held. This new debug mechanism adds the concept of associated locks. sequence count has now lock type variants and corresponding initializers which take a pointer to the associated lock used for writer serialization. If lockdep is enabled the pointer is stored and write_seqcount_begin() has a lockdep assertion to validate that the lock is held. Aside of the type and the initializer no other code changes are required at the seqcount usage sites. The rest of the seqcount API is unchanged and determines the type at compile time with the help of _Generic which is possible now that the minimal GCC version has been moved up. Adding this lockdep coverage unearthed a handful of seqcount bugs which have been addressed already independent of this. While generally useful this comes with a Trojan Horse twist: On RT kernels the write side critical section can become preemtible if the writers are serialized by an associated lock, which leads to the well known reader preempts writer livelock. RT prevents this by storing the associated lock pointer independent of lockdep in the seqcount and changing the reader side to block on the lock when a reader detects that a writer is in the write side critical section. - Conversion of seqcount usage sites to associated types and initializers" * tag 'locking-urgent-2020-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits) locking/seqlock, headers: Untangle the spaghetti monster locking, arch/ia64: Reduce <asm/smp.h> header dependencies by moving XTP bits into the new <asm/xtp.h> header x86/headers: Remove APIC headers from <asm/smp.h> seqcount: More consistent seqprop names seqcount: Compress SEQCNT_LOCKNAME_ZERO() seqlock: Fold seqcount_LOCKNAME_init() definition seqlock: Fold seqcount_LOCKNAME_t definition seqlock: s/__SEQ_LOCKDEP/__SEQ_LOCK/g hrtimer: Use sequence counter with associated raw spinlock kvm/eventfd: Use sequence counter with associated spinlock userfaultfd: Use sequence counter with associated spinlock NFSv4: Use sequence counter with associated spinlock iocost: Use sequence counter with associated spinlock raid5: Use sequence counter with associated spinlock vfs: Use sequence counter with associated spinlock timekeeping: Use sequence counter with associated raw spinlock xfrm: policy: Use sequence counters with associated lock netfilter: nft_set_rbtree: Use sequence counter with associated rwlock netfilter: conntrack: Use sequence counter with associated spinlock sched: tasks: Use sequence counter with associated spinlock ...
2020-08-05Merge tag 'for-5.9/drivers-20200803' of git://git.kernel.dk/linux-blockLinus Torvalds1-140/+246
Pull block driver updates from Jens Axboe: - NVMe: - ZNS support (Aravind, Keith, Matias, Niklas) - Misc cleanups, optimizations, fixes (Baolin, Chaitanya, David, Dongli, Max, Sagi) - null_blk zone capacity support (Aravind) - MD: - raid5/6 fixes (ChangSyun) - Warning fixes (Damien) - raid5 stripe fixes (Guoqing, Song, Yufen) - sysfs deadlock fix (Junxiao) - raid10 deadlock fix (Vitaly) - struct_size conversions (Gustavo) - Set of bcache updates/fixes (Coly) * tag 'for-5.9/drivers-20200803' of git://git.kernel.dk/linux-block: (117 commits) md/raid5: Allow degraded raid6 to do rmw md/raid5: Fix Force reconstruct-write io stuck in degraded raid5 raid5: don't duplicate code for different paths in handle_stripe raid5-cache: hold spinlock instead of mutex in r5c_journal_mode_show md: print errno in super_written md/raid5: remove the redundant setting of STRIPE_HANDLE md: register new md sysfs file 'uuid' read-only md: fix max sectors calculation for super 1.0 nvme-loop: remove extra variable in create ctrl nvme-loop: set ctrl state connecting after init nvme-multipath: do not fall back to __nvme_find_path() for non-optimized paths nvme-multipath: fix logic for non-optimized paths nvme-rdma: fix controller reset hang during traffic nvme-tcp: fix controller reset hang during traffic nvmet: introduce the passthru Kconfig option nvmet: introduce the passthru configfs interface nvmet: Add passthru enable/disable helpers nvmet: add passthru code to process commands nvme: export nvme_find_get_ns() and nvme_put_ns() nvme: introduce nvme_ctrl_get_by_path() ...
2020-08-04Merge tag 'uninit-macro-v5.9-rc1' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull uninitialized_var() macro removal from Kees Cook: "This is long overdue, and has hidden too many bugs over the years. The series has several "by hand" fixes, and then a trivial treewide replacement. - Clean up non-trivial uses of uninitialized_var() - Update documentation and checkpatch for uninitialized_var() removal - Treewide removal of uninitialized_var()" * tag 'uninit-macro-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: compiler: Remove uninitialized_var() macro treewide: Remove uninitialized_var() usage checkpatch: Remove awareness of uninitialized_var() macro mm/debug_vm_pgtable: Remove uninitialized_var() usage f2fs: Eliminate usage of uninitialized_var() macro media: sur40: Remove uninitialized_var() usage KVM: PPC: Book3S PR: Remove uninitialized_var() usage clk: spear: Remove uninitialized_var() usage clk: st: Remove uninitialized_var() usage spi: davinci: Remove uninitialized_var() usage ide: Remove uninitialized_var() usage rtlwifi: rtl8192cu: Remove uninitialized_var() usage b43: Remove uninitialized_var() usage drbd: Remove uninitialized_var() usage x86/mm/numa: Remove uninitialized_var() usage docs: deprecated.rst: Add uninitialized_var()
2020-08-02md/raid5: Allow degraded raid6 to do rmwChangSyun Peng1-6/+16
Degraded raid6 always do reconstruct-write now. With raid6 xor supported, we can do rmw in degraded raid6. This patch can reduce many read IOs to improve performance. If the failed disk is P, Q or the disk we want to write to, we may need to do reconstruct-write in max degraded raid6. In this situation we can not read enough data from handle_stripe_dirtying() so we have to set force_rcw in handle_stripe_fill() to read all data. Reviewed-by: Alex Wu <alexwu@synology.com> Reviewed-by: BingJing Chang <bingjingc@synology.com> Reviewed-by: Danny Shih <dannyshih@synology.com> Signed-off-by: ChangSyun Peng <allenpeng@synology.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-08-02md/raid5: Fix Force reconstruct-write io stuck in degraded raid5ChangSyun Peng1-1/+2
In degraded raid5, we need to read parity to do reconstruct-write when data disks fail. However, we can not read parity from handle_stripe_dirtying() in force reconstruct-write mode. Reproducible Steps: 1. Create degraded raid5 mdadm -C /dev/md2 --assume-clean -l5 -n3 /dev/sda2 /dev/sdb2 missing 2. Set rmw_level to 0 echo 0 > /sys/block/md2/md/rmw_level 3. IO to raid5 Now some io may be stuck in raid5. We can use handle_stripe_fill() to read the parity in this situation. Cc: <stable@vger.kernel.org> # v4.4+ Reviewed-by: Alex Wu <alexwu@synology.com> Reviewed-by: BingJing Chang <bingjingc@synology.com> Reviewed-by: Danny Shih <dannyshih@synology.com> Signed-off-by: ChangSyun Peng <allenpeng@synology.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-08-02raid5: don't duplicate code for different paths in handle_stripeGuoqing Jiang1-6/+3
As we can see, R5_LOCKED is set and s.locked is increased whether R5_ReWrite is set or not, so move it to common path. Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-08-02md/raid5: remove the redundant setting of STRIPE_HANDLEGuoqing Jiang1-6/+2
The flag is already set before compare rcw with rmw, so it is not necessary to do it again. Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-07-29raid5: Use sequence counter with associated spinlockAhmed S. Darwish1-1/+1
A sequence counter write side critical section must be protected by some form of locking to serialize writers. A plain seqcount_t does not contain the information of which lock must be held when entering a write side critical section. Use the new seqcount_spinlock_t data type, which allows to associate a spinlock with the sequence counter. This enables lockdep to verify that the spinlock used for writer serialization is held when the write side critical section is entered. If lockdep is disabled this lock association is compiled out and has neither storage size nor runtime overhead. Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Song Liu <song@kernel.org> Link: https://lkml.kernel.org/r/20200720155530.1173732-20-a.darwish@linutronix.de
2020-07-22md/raid5: use do_div() for 64 bit divisions in raid5_sync_requestYufen Yu1-1/+1
We get compilation error on 32-bit architectures (e.g. m68k), as: ERROR: modpost: "__udivdi3" [drivers/md/raid456.ko] undefined! Since 'sync_blocks' is defined as u64, use do_div() to fix this error. Fixes: c911c46c017c ("md/raid456: convert macro STRIPE_* to RAID5_STRIPE_*") Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-07-21md/raid5: support config stripe_size by sysfs entryYufen Yu1-0/+72
Adding a new 'stripe_size' sysfs entry to set and show stripe_size. stripe_size should not be bigger than PAGE_SIZE, and it requires to be multiple of 4096. We can adjust stripe_size by writing value into sysfs entry, likely, set stripe_size as 16KB: echo 16384 > /sys/block/md1/md/stripe_size Show current stripe_size value: cat /sys/block/md1/md/stripe_size For PAGE_SIZE is equal to 4096, 'stripe_size' can just be read. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-07-21md/raid5: set default stripe_size as 4096Yufen Yu1-0/+5
In RAID5, if issued bio size is bigger than stripe_size, it will be split in the unit of stripe_size and process them one by one. Even for size less then stripe_size, RAID5 also request data from disk at least of stripe_size. Nowdays, stripe_size is equal to the value of PAGE_SIZE. Since filesystem usually issue bio in the unit of 4KB, there is no problem for PAGE_SIZE as 4KB. But, for 64KB PAGE_SIZE, bio from filesystem requests 4KB data while RAID5 issue IO at least stripe_size (64KB) each time. That will waste resource of disk bandwidth and compute xor. To avoding the waste, we want to make stripe_size configurable. This patch just set default stripe_size as 4096. User can also set the value bigger than 4KB for some special requirements, such as we know the issued io size is more than 4KB. To evaluate the new feature, we create raid5 device '/dev/md5' with 4 SSD disk and test it on arm64 machine with 64KB PAGE_SIZE. 1) We format /dev/md5 with mkfs.ext4 and mount ext4 with default configure on /mnt directory. Then, trying to test it by dbench with command: dbench -D /mnt -t 1000 10. Result show as: 'stripe_size = 64KB' Operation Count AvgLat MaxLat ---------------------------------------- NTCreateX 9805011 0.021 64.728 Close 7202525 0.001 0.120 Rename 415213 0.051 44.681 Unlink 1980066 0.079 93.147 Deltree 240 1.793 6.516 Mkdir 120 0.004 0.007 Qpathinfo 8887512 0.007 37.114 Qfileinfo 1557262 0.001 0.030 Qfsinfo 1629582 0.012 0.152 Sfileinfo 798756 0.040 57.641 Find 3436004 0.019 57.782 WriteX 4887239 0.021 57.638 ReadX 15370483 0.005 37.818 LockX 31934 0.003 0.022 UnlockX 31933 0.001 0.021 Flush 687205 13.302 530.088 Throughput 307.799 MB/sec 10 clients 10 procs max_latency=530.091 ms ------------------------------------------------------- 'stripe_size = 4KB' Operation Count AvgLat MaxLat ---------------------------------------- NTCreateX 11999166 0.021 36.380 Close 8814128 0.001 0.122 Rename 508113 0.051 29.169 Unlink 2423242 0.070 38.141 Deltree 300 1.885 7.155 Mkdir 150 0.004 0.006 Qpathinfo 10875921 0.007 35.485 Qfileinfo 1905837 0.001 0.032 Qfsinfo 1994304 0.012 0.125 Sfileinfo 977450 0.029 26.489 Find 4204952 0.019 9.361 WriteX 5981890 0.019 27.804 ReadX 18809742 0.004 33.491 LockX 39074 0.003 0.025 UnlockX 39074 0.001 0.014 Flush 841022 10.712 458.848 Throughput 376.777 MB/sec 10 clients 10 procs max_latency=458.852 ms ------------------------------------------------------- It show that setting stripe_size as 4KB has higher thoughput, i.e. (376.777 vs 307.799) and has smaller latency than that setting as 64KB. 2) We try to evaluate IO throughput for /dev/md5 by fio with config: [4KB randwrite] direct=1 numjob=2 iodepth=64 ioengine=libaio filename=/dev/md5 bs=4KB rw=randwrite [64KB write] direct=1 numjob=2 iodepth=64 ioengine=libaio filename=/dev/md5 bs=1MB rw=write The result as follow: + + | stripe_size(64KB) | stripe_size(4KB) +----------------------------------------------------+ 4KB randwrite | 15MB/s | 100MB/s +----------------------------------------------------+ 1MB write | 1000MB/s | 700MB/s The result show that when size of io is bigger than 4KB (64KB), 64KB stripe_size has much higher IOPS. But for 4KB randwrite, that means, size of io issued to device are smaller, 4KB stripe_size have better performance. Normally, default value (4096) can get relatively good performance. But if each issued io is bigger than 4096, setting value more than 4096 may get better performance. Here, we just set default stripe_size as 4096, and we will try to support setting different stripe_size by sysfs interface in the following patch. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-07-21md/raid456: convert macro STRIPE_* to RAID5_STRIPE_*Yufen Yu1-102/+123
Convert macro STRIPE_SIZE, STRIPE_SECTORS and STRIPE_SHIFT to RAID5_STRIPE_SIZE(), RAID5_STRIPE_SECTORS() and RAID5_STRIPE_SHIFT(). This patch is prepare for the following adjustable stripe_size. It will not change any existing functionality. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-07-16treewide: Remove uninitialized_var() usageKees Cook1-1/+1
Using uninitialized_var() is dangerous as it papers over real bugs[1] (or can in the future), and suppresses unrelated compiler warnings (e.g. "unused variable"). If the compiler thinks it is uninitialized, either simply initialize the variable or make compiler changes. In preparation for removing[2] the[3] macro[4], remove all remaining needless uses with the following script: git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \ xargs perl -pi -e \ 's/\buninitialized_var\(([^\)]+)\)/\1/g; s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;' drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid pathological white-space. No outstanding warnings were found building allmodconfig with GCC 9.3.0 for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64, alpha, and m68k. [1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/ [2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/ [3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/ [4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/ Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5 Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs Signed-off-by: Kees Cook <keescook@chromium.org>
2020-07-16raid5: remove the meaningless check in raid5_make_requestGuoqing Jiang1-2/+1
We can't guarntee the batched stripe to be set with STRIPE_HANDLE since there are lots of functions could set the flag, such as sync_request, ops_complete_* and end_{read,write}_request etc. Also clear_batch_ready called in handle_stripe ensures the batched list can't continue to be handled by handle_stripe. Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-07-16raid5: put the comment of clear_batch_ready to the right placeGuoqing Jiang1-4/+4
To make people understand the function well, let's put the comment to the right place. Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-07-16raid5: call clear_batch_ready before set STRIPE_ACTIVEGuoqing Jiang1-5/+10
We tried to only put the head sh of batch list to handle_list, then the handle_stripe doesn't handle other members in the batch list. However, we still got the calltrace in break_stripe_batch_list. [593764.644269] stripe state: 2003 kernel: [593764.644299] ------------[ cut here ]------------ kernel: [593764.644308] WARNING: CPU: 12 PID: 856 at drivers/md/raid5.c:4625 break_stripe_batch_list+0x203/0x240 [raid456] [...] kernel: [593764.644363] Call Trace: kernel: [593764.644370] handle_stripe+0x907/0x20c0 [raid456] kernel: [593764.644376] ? __wake_up_common_lock+0x89/0xc0 kernel: [593764.644379] handle_active_stripes.isra.57+0x35f/0x570 [raid456] kernel: [593764.644382] ? raid5_wakeup_stripe_thread+0x96/0x1f0 [raid456] kernel: [593764.644385] raid5d+0x480/0x6a0 [raid456] kernel: [593764.644390] ? md_thread+0x11f/0x160 kernel: [593764.644392] md_thread+0x11f/0x160 kernel: [593764.644394] ? wait_woken+0x80/0x80 kernel: [593764.644396] kthread+0xfc/0x130 kernel: [593764.644398] ? find_pers+0x70/0x70 kernel: [593764.644399] ? kthread_create_on_node+0x70/0x70 kernel: [593764.644401] ret_from_fork+0x1f/0x30 As we can see, the stripe was set with STRIPE_ACTIVE and STRIPE_HANDLE, and only handle_stripe could set those flags then return. And since the stipe was already in the batch list, we need to return earlier before set the two flags. And after dig a little about git history especially commit 3664847d95e6 ("md/raid5: fix a race condition in stripe batch"), it seems the batched stipe still could be handled by handle_stipe, then handle_stipe needs to return earlier if clear_batch_ready to return true. Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-07-15md: raid5: Fix compilation warningDamien Le Moal1-6/+6
Remove the if statement around the calls to sysfs_link_rdev() to avoid the compilation warning "suggest braces around empty body in an ‘if’ statement" when compiling with W=1. Also fix function description comments to avoid kdoc format warnings. Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-07-14md: fix deadlock causing by sysfs_notifyJunxiao Bi1-3/+3
The following deadlock was captured. The first process is holding 'kernfs_mutex' and hung by io. The io was staging in 'r1conf.pending_bio_list' of raid1 device, this pending bio list would be flushed by second process 'md127_raid1', but it was hung by 'kernfs_mutex'. Using sysfs_notify_dirent_safe() to replace sysfs_notify() can fix it. There were other sysfs_notify() invoked from io path, removed all of them. PID: 40430 TASK: ffff8ee9c8c65c40 CPU: 29 COMMAND: "probe_file" #0 [ffffb87c4df37260] __schedule at ffffffff9a8678ec #1 [ffffb87c4df372f8] schedule at ffffffff9a867f06 #2 [ffffb87c4df37310] io_schedule at ffffffff9a0c73e6 #3 [ffffb87c4df37328] __dta___xfs_iunpin_wait_3443 at ffffffffc03a4057 [xfs] #4 [ffffb87c4df373a0] xfs_iunpin_wait at ffffffffc03a6c79 [xfs] #5 [ffffb87c4df373b0] __dta_xfs_reclaim_inode_3357 at ffffffffc039a46c [xfs] #6 [ffffb87c4df37400] xfs_reclaim_inodes_ag at ffffffffc039a8b6 [xfs] #7 [ffffb87c4df37590] xfs_reclaim_inodes_nr at ffffffffc039bb33 [xfs] #8 [ffffb87c4df375b0] xfs_fs_free_cached_objects at ffffffffc03af0e9 [xfs] #9 [ffffb87c4df375c0] super_cache_scan at ffffffff9a287ec7 #10 [ffffb87c4df37618] shrink_slab at ffffffff9a1efd93 #11 [ffffb87c4df37700] shrink_node at ffffffff9a1f5968 #12 [ffffb87c4df37788] do_try_to_free_pages at ffffffff9a1f5ea2 #13 [ffffb87c4df377f0] try_to_free_mem_cgroup_pages at ffffffff9a1f6445 #14 [ffffb87c4df37880] try_charge at ffffffff9a26cc5f #15 [ffffb87c4df37920] memcg_kmem_charge_memcg at ffffffff9a270f6a #16 [ffffb87c4df37958] new_slab at ffffffff9a251430 #17 [ffffb87c4df379c0] ___slab_alloc at ffffffff9a251c85 #18 [ffffb87c4df37a80] __slab_alloc at ffffffff9a25635d #19 [ffffb87c4df37ac0] kmem_cache_alloc at ffffffff9a251f89 #20 [ffffb87c4df37b00] alloc_inode at ffffffff9a2a2b10 #21 [ffffb87c4df37b20] iget_locked at ffffffff9a2a4854 #22 [ffffb87c4df37b60] kernfs_get_inode at ffffffff9a311377 #23 [ffffb87c4df37b80] kernfs_iop_lookup at ffffffff9a311e2b #24 [ffffb87c4df37ba8] lookup_slow at ffffffff9a290118 #25 [ffffb87c4df37c10] walk_component at ffffffff9a291e83 #26 [ffffb87c4df37c78] path_lookupat at ffffffff9a293619 #27 [ffffb87c4df37cd8] filename_lookup at ffffffff9a2953af #28 [ffffb87c4df37de8] user_path_at_empty at ffffffff9a295566 #29 [ffffb87c4df37e10] vfs_statx at ffffffff9a289787 #30 [ffffb87c4df37e70] SYSC_newlstat at ffffffff9a289d5d #31 [ffffb87c4df37f18] sys_newlstat at ffffffff9a28a60e #32 [ffffb87c4df37f28] do_syscall_64 at ffffffff9a003949 #33 [ffffb87c4df37f50] entry_SYSCALL_64_after_hwframe at ffffffff9aa001ad RIP: 00007f617a5f2905 RSP: 00007f607334f838 RFLAGS: 00000246 RAX: ffffffffffffffda RBX: 00007f6064044b20 RCX: 00007f617a5f2905 RDX: 00007f6064044b20 RSI: 00007f6064044b20 RDI: 00007f6064005890 RBP: 00007f6064044aa0 R8: 0000000000000030 R9: 000000000000011c R10: 0000000000000013 R11: 0000000000000246 R12: 00007f606417e6d0 R13: 00007f6064044aa0 R14: 00007f6064044b10 R15: 00000000ffffffff ORIG_RAX: 0000000000000006 CS: 0033 SS: 002b PID: 927 TASK: ffff8f15ac5dbd80 CPU: 42 COMMAND: "md127_raid1" #0 [ffffb87c4df07b28] __schedule at ffffffff9a8678ec #1 [ffffb87c4df07bc0] schedule at ffffffff9a867f06 #2 [ffffb87c4df07bd8] schedule_preempt_disabled at ffffffff9a86825e #3 [ffffb87c4df07be8] __mutex_lock at ffffffff9a869bcc #4 [ffffb87c4df07ca0] __mutex_lock_slowpath at ffffffff9a86a013 #5 [ffffb87c4df07cb0] mutex_lock at ffffffff9a86a04f #6 [ffffb87c4df07cc8] kernfs_find_and_get_ns at ffffffff9a311d83 #7 [ffffb87c4df07cf0] sysfs_notify at ffffffff9a314b3a #8 [ffffb87c4df07d18] md_update_sb at ffffffff9a688696 #9 [ffffb87c4df07d98] md_update_sb at ffffffff9a6886d5 #10 [ffffb87c4df07da8] md_check_recovery at ffffffff9a68ad9c #11 [ffffb87c4df07dd0] raid1d at ffffffffc01f0375 [raid1] #12 [ffffb87c4df07ea0] md_thread at ffffffff9a680348 #13 [ffffb87c4df07f08] kthread at ffffffff9a0b8005 #14 [ffffb87c4df07f50] ret_from_fork at ffffffff9aa00344 Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-07-08writeback: remove bdi->congested_fnChristoph Hellwig1-25/+0
Except for pktdvd, the only places setting congested bits are file systems that allocate their own backing_dev_info structures. And pktdvd is a deprecated driver that isn't useful in stack setup either. So remove the dead congested_fn stacking infrastructure. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Song Liu <song@kernel.org> Acked-by: David Sterba <dsterba@suse.com> [axboe: fixup unused variables in bcache/request.c] Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-07-01block: rename generic_make_request to submit_bio_noacctChristoph Hellwig1-5/+5
generic_make_request has always been very confusingly misnamed, so rename it to submit_bio_noacct to make it clear that it is submit_bio minus accounting and a few checks. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-05-13raid5: update code comment of scribble_alloc()Coly Li1-2/+5
Code comments of scribble_alloc() is outdated for a while. This patch update the comments in function header for the new parameter list. Suggested-by: Song Liu <songliubraving@fb.com> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-05-13raid5: remove gfp flags from scribble_alloc()Coly Li1-6/+9
Using GFP_NOIO flag to call scribble_alloc() from resize_chunk() does not have the expected behavior. kvmalloc_array() inside scribble_alloc() which receives the GFP_NOIO flag will eventually call kmalloc_node() to allocate physically continuous pages. Now we have memalloc scope APIs in mddev_suspend()/mddev_resume() to prevent memory reclaim I/Os during raid array suspend context, calling to kvmalloc_array() with GFP_KERNEL flag may avoid deadlock of recursive I/O as expected. This patch removes the useless gfp flags from parameters list of scribble_alloc(), and call kvmalloc_array() with GFP_KERNEL flag. The incorrect GFP_NOIO flag does not exist anymore. Fixes: b330e6a49dc3 ("md: convert to kvmalloc") Suggested-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Song Liu <songliubraving@fb.com>
2020-01-13raid5: remove worker_cnt_per_group argument from alloc_thread_groupsGuoqing Jiang1-14/+7
We can use "cnt" directly to update conf->worker_cnt_per_group if alloc_thread_groups returns 0. Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-12-11raid5: need to set STRIPE_HANDLE for batch headGuoqing Jiang1-1/+1
With commit 6ce220dd2f8ea71d6afc29b9a7524c12e39f374a ("raid5: don't set STRIPE_HANDLE to stripe which is in batch list"), we don't want to set STRIPE_HANDLE flag for sh which is already in batch list. However, the stripe which is the head of batch list should set this flag, otherwise panic could happen inside init_stripe at BUG_ON(sh->batch_head), it is reproducible with raid5 on top of nvdimm devices per Xiao oberserved. Thanks for Xiao's effort to verify the change. Fixes: 6ce220dd2f8ea ("raid5: don't set STRIPE_HANDLE to stripe which is in batch list") Reported-by: Xiao Ni <xni@redhat.com> Tested-by: Xiao Ni <xni@redhat.com> Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-11-14drivers/md/raid5.c: use the new spelling of RWH_WRITE_LIFE_NOT_SETEugene Syromiatnikov1-2/+2
As it is consistent with prefixes of other write life time hints. Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-10-24md: improve handling of bio with REQ_PREFLUSH in md_flush_request()David Jeffery1-2/+2
If pers->make_request fails in md_flush_request(), the bio is lost. To fix this, pass back a bool to indicate if the original make_request call should continue to handle the I/O and instead of assuming the flush logic will push it to completion. Convert md_flush_request to return a bool and no longer calls the raid driver's make_request function. If the return is true, then the md flush logic has or will complete the bio and the md make_request call is done. If false, then the md make_request function needs to keep processing like it is a normal bio. Let the original call to md_handle_request handle any need to retry sending the bio to the raid driver's make_request function should it be needed. Also mark md_flush_request and the make_request function pointer as __must_check to issue warnings should these critical return values be ignored. Fixes: 2bc13b83e629 ("md: batch flush requests.") Cc: stable@vger.kernel.org # # v4.19+ Cc: NeilBrown <neilb@suse.com> Signed-off-by: David Jeffery <djeffery@redhat.com> Reviewed-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-09-13raid5: remove STRIPE_OPS_REQ_PENDINGGuoqing Jiang1-1/+0
This stripe state is not used anymore after commit 51acbcec6c42b24 ("md: remove CONFIG_MULTICORE_RAID456"), so remove the obsoleted state. gjiang@nb01257:~/md$ grep STRIPE_OPS_REQ_PENDING drivers/md/ -r drivers/md/raid5.c: (1 << STRIPE_OPS_REQ_PENDING) | drivers/md/raid5.h: STRIPE_OPS_REQ_PENDING, Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-09-13raid5: don't set STRIPE_HANDLE to stripe which is in batch listGuoqing Jiang1-1/+2
If stripe in batch list is set with STRIPE_HANDLE flag, then the stripe could be set with STRIPE_ACTIVE by the handle_stripe function. And if error happens to the batch_head at the same time, break_stripe_batch_list is called, then below warning could happen (the same report in [1]), it means a member of batch list was set with STRIPE_ACTIVE. [7028915.431770] stripe state: 2001 [7028915.431815] ------------[ cut here ]------------ [7028915.431828] WARNING: CPU: 18 PID: 29089 at drivers/md/raid5.c:4614 break_stripe_batch_list+0x203/0x240 [raid456] [...] [7028915.431879] CPU: 18 PID: 29089 Comm: kworker/u82:5 Tainted: G O 4.14.86-1-storage #4.14.86-1.2~deb9 [7028915.431881] Hardware name: Supermicro SSG-2028R-ACR24L/X10DRH-iT, BIOS 3.1 06/18/2018 [7028915.431888] Workqueue: raid5wq raid5_do_work [raid456] [7028915.431890] task: ffff9ab0ef36d7c0 task.stack: ffffb72926f84000 [7028915.431896] RIP: 0010:break_stripe_batch_list+0x203/0x240 [raid456] [7028915.431898] RSP: 0018:ffffb72926f87ba8 EFLAGS: 00010286 [7028915.431900] RAX: 0000000000000012 RBX: ffff9aaa84a98000 RCX: 0000000000000000 [7028915.431901] RDX: 0000000000000000 RSI: ffff9ab2bfa15458 RDI: ffff9ab2bfa15458 [7028915.431902] RBP: ffff9aaa8fb4e900 R08: 0000000000000001 R09: 0000000000002eb4 [7028915.431903] R10: 00000000ffffffff R11: 0000000000000000 R12: ffff9ab1736f1b00 [7028915.431904] R13: 0000000000000000 R14: ffff9aaa8fb4e900 R15: 0000000000000001 [7028915.431906] FS: 0000000000000000(0000) GS:ffff9ab2bfa00000(0000) knlGS:0000000000000000 [7028915.431907] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [7028915.431908] CR2: 00007ff953b9f5d8 CR3: 0000000bf4009002 CR4: 00000000003606e0 [7028915.431909] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [7028915.431910] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [7028915.431910] Call Trace: [7028915.431923] handle_stripe+0x8e7/0x2020 [raid456] [7028915.431930] ? __wake_up_common_lock+0x89/0xc0 [7028915.431935] handle_active_stripes.isra.58+0x35f/0x560 [raid456] [7028915.431939] raid5_do_work+0xc6/0x1f0 [raid456] Also commit 59fc630b8b5f9f ("RAID5: batch adjacent full stripe write") said "If a stripe is added to batch list, then only the first stripe of the list should be put to handle_list and run handle_stripe." So don't set STRIPE_HANDLE to stripe which is already in batch list, otherwise the stripe could be put to handle_list and run handle_stripe, then the above warning could be triggered. [1]. https://www.spinics.net/lists/raid/msg62552.html Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-09-13raid5: don't increment read_errors on EILSEQ returnNigel Croxon1-1/+2
While MD continues to count read errors returned by the lower layer. If those errors are -EILSEQ, instead of -EIO, it should NOT increase the read_errors count. When RAID6 is set up on dm-integrity target that detects massive corruption, the leg will be ejected from the array. Even if the issue is correctable with a sector re-write and the array has necessary redundancy to correct it. The leg is ejected because it runs up the rdev->read_errors beyond conf->max_nr_stripes. The return status in dm-drypt when there is a data integrity error is -EILSEQ (BLK_STS_PROTECTION). Signed-off-by: Nigel Croxon <ncroxon@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-09-03md/raid5: use bio_end_sector to calculate last_sectorGuoqing Jiang1-1/+1
Use the common way to get last_sector. Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-08-27raid5 improve too many read errors msg by adding limitsNigel Croxon1-4/+10
Often limits can be changed by admin. When discussing such things it helps if you can provide "self-sustained" facts. Also sometimes the admin thinks he changed a limit, but it did not take effect for some reason or he changed the wrong thing. V3: Only pr_warn when Faulty is 0. V2: Add read_errors value to pr_warn. Signed-off-by: Nigel Croxon <ncroxon@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-08-07md/raid6: Set R5_ReadError when there is read failure on parity diskXiao Ni1-1/+3
7471fb77ce4d ("md/raid6: Fix anomily when recovering a single device in RAID6.") avoids rereading P when it can be computed from other members. However, this misses the chance to re-write the right data to P. This patch sets R5_ReadError if the re-read fails. Also, when re-read is skipped, we also missed the chance to reset rdev->read_errors to 0. It can fail the disk when there are many read errors on P member disk (other disks don't have read error) V2: upper layer read request don't read parity/Q data. So there is no need to consider such situation. This is Reported-by: kbuild test robot <lkp@intel.com> Fixes: 7471fb77ce4d ("md/raid6: Fix anomily when recovering a single device in RAID6.") Cc: <stable@vger.kernel.org> #4.4+ Signed-off-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-06-20block: remove the bi_phys_segments field in struct bioChristoph Hellwig1-1/+0
We only need the number of segments in the blk-mq submission path. Remove the field from struct bio, and return it from a variant of blk_queue_split instead of that it can passed as an argument to those functions that need the value. This also means we stop recounting segments except for cloning and partial segments. To keep the number of arguments in this how path down remove pointless struct request_queue arguments from any of the functions that had it and grew a nr_segs argument. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-06-15raid5-cache: Need to do start() part job after adding journal deviceXiao Ni1-2/+9
commit d5d885fd514f ("md: introduce new personality funciton start()") splits the init job to two parts. The first part run() does the jobs that do not require the md threads. The second part start() does the jobs that require the md threads. Now it just does run() in adding new journal device. It needs to do the second part start() too. Fixes: d5d885fd514f ("md: introduce new personality funciton start()") Cc: stable@vger.kernel.org #v4.9+ Reported-by: Michal Soltys <soltys@ziu.info> Signed-off-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-05-24treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 47Thomas Gleixner1-9/+1
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 or at your option any later version you should have received a copy of the gnu general public license for example usr src linux copying if not write to the free software foundation inc 675 mass ave cambridge ma 02139 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 20 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190520170858.552543146@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-10-30 21:57:24 +0000