| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This adds basic support for LEDs on the front side of CZ.NIC's Turris
Omnia router.
There are 12 RGB LEDs. The controller supports HW triggering mode for
the LEDs, but this driver does not support it yet, and sets all the LEDs
defined in device-tree into SW mode upon probe.
This driver uses the multicolor LED framework.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Introduce a multicolor class that groups colored LEDs
within a LED node.
The multicolor class groups monochrome LEDs and allows controlling two
aspects of the final combined color: hue and lightness. The former is
controlled via the intensity file and the latter is controlled
via brightness file.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[squashed leds: multicolor: Fix camel case in documentation in]
|
|
This commit adds support for AWINIC AW2013 3-channel LED driver.
The chip supports 3 PWM channels and is controlled with I2C.
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Add a driver for the SGMICRO SGM3140 Buck/Boost Charge Pump LED driver.
This device is controlled by two GPIO pins, one for enabling and the
second one for switching between torch and flash mode.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
This adds support for controlling the LEDs attached to the Embedded
Controller on a Dell Wyse 3020 "Ariel" board.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Sort Makefile entries to reduce risk of rejects.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
This patch implemenets a driver to support the front panel LEDs of
SGI Octane (IP30) workstations.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
This driver adds support for the LED operational mode of the
tps6105x MFD device.
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
This patch adds a LED class driver for the LEDs found on
the Crane Merchandising System EL15203000 LEDs board
(aka RED LEDs board).
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Merge immutable branch between LEDs, MFD and REGULATOR due to
TI LMU LED support rework and introduction of two new drivers
with DT bindings.
* tag 'ti-lmu-led-drivers':
leds: lm36274: Introduce the TI LM36274 LED driver
dt-bindings: leds: Add LED bindings for the LM36274
regulator: lm363x: Add support for LM36274
mfd: ti-lmu: Add LM36274 support to the ti-lmu
dt-bindings: mfd: Add lm36274 bindings to ti-lmu
leds: lm3697: Introduce the lm3697 driver
mfd: ti-lmu: Remove support for LM3697
dt-bindings: ti-lmu: Modify dt bindings for the LM3697
leds: TI LMU: Add common code for TI LMU devices
dt-bindings: mfd: LMU: Add ti,brightness-resolution
dt-bindings: mfd: LMU: Add the ramp up/down property
|
|
Introduce the LM36274 LED driver. This driver uses the ti-lmu
MFD driver to probe this LED driver. The driver configures only the
LED registers and enables the outputs according to the config file.
The driver utilizes the TI LMU (Lighting Management Unit) LED common
framework to set the brightness bits.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
Introduce the lm3697 LED driver for backlighting and display.
Datasheet location:
http://www.ti.com/lit/ds/symlink/lm3697.pdf
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
Create a TI LMU common framework for TI LMU devices that share
common features.
Currently the runtime ramp and brightness setting have
been identified as common features with common register settings.
This work is derived from Milo Kims TI LMU MFD code.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
This driver adds support for simple SPI based LED controller which use
only one byte for setting the brightness.
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
'ib-mfd-pinctrl-5.2-2' and 'ib-mfd-regulator-5.2', tag 'ib-mfd-arm-net-5.2' into ibs-for-mfd-merged
Immutable branch between MFD, ARM and Net due for the 5.2 merge window
|
|
This adds basic support for LEDs for the max77650 PMIC. The device has
three current sinks for driving LEDs.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Introduce the Texas Instruments LM3532 White LED driver.
The driver supports ALS configurability or manual brightness
control.
The driver also supports associating LED strings with specific
control banks in a group or as individually controlled strings.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
AN30259A is a 3-channel LED driver which uses I2C. It supports timed
operation via an internal PWM clock, and variable brightness. This
driver offers support for basic hardware-based blinking and brightness
control.
The datasheet is freely available:
https://www.alliedelec.com/m/d/a9d2b3ee87c2d1a535a41dd747b1c247.pdf
Signed-off-by: Simon Shields <simon@lineageos.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
Introduce the family of LED devices that can
drive a torch, strobe or IR LED.
The LED driver can be configured with a strobe
timer to execute a strobe flash. The IR LED
brightness is controlled via the torch brightness
register.
The data sheet for each the LM36010 and LM36011
LED drivers can be found here:
http://www.ti.com/product/LM36010
http://www.ti.com/product/LM36011
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
This patch adds Spreadtrum SC27xx PMIC series breathing light controller
driver, which can support 3 LEDs. Each LED can work at normal PWM mode
and breathing mode.
Signed-off-by: Xiaotong Lu <xiaotong.lu@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
This patch adds a LED class driver for the RGB LEDs found on
the Crane Merchandising System CR0014114 LEDs board.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
Driver obtains LED devices according to system configuration and creates
devices in form: "devicename:color:function", like
The full path is to be:
/sys/class/leds/mlxreg\:status\:amber/brightness
After timer trigger activation:
echo timer > /sys/class/leds/mlxreg\:status\:amber/trigger
Attributes for LED blinking will appaer in sysfs infrastructure:
/sys/class/leds/mlxreg\:status\:amber/delay_off
/sys/class/leds/mlxreg\:status\:amber/delay_on
LED setting is controlled through the on-board programmable devices,
which exports its register map. This device could be attached to any
bus type, for which register mapping is supported.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
Introducing the LM3692x Dual-String white LED driver.
Data sheet is located
http://www.ti.com/lit/ds/snvsa29/snvsa29.pdf
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- add a driver for PC Engines APU/APU2 LEDs
New LED trigger:
- add a system activity LED trigger
LED core improvements:
- replace flags bit shift with BIT() macros
Convert timers to use timer_setup() in:
- led-core
- ledtrig-activity
- ledtrig-heartbeat
- ledtrig-transient
LED class drivers fixes:
- lp55xx: fix spelling mistake: 'cound' -> 'could'
- tca6507: Remove unnecessary reg check
- pca955x: Don't invert requested value in pca955x_gpio_set_value()
LED documentation improvements:
- update 00-INDEX file"
* tag 'leds_for_4.15rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: Add driver for PC Engines APU/APU2 LEDs
leds: lp55xx: fix spelling mistake: 'cound' -> 'could'
leds: Convert timers to use timer_setup()
Documentation: leds: Update 00-INDEX file
leds: tca6507: Remove unnecessary reg check
leds: ledtrig-heartbeat: Convert timers to use timer_setup()
leds: Replace flags bit shift with BIT() macros
leds: pca955x: Don't invert requested value in pca955x_gpio_set_value()
leds: ledtrig-activity: Add a system activity LED trigger
|
|
This patch implements the driver to support the front panel LEDs
for PC Engines APU and APU2 boards.
Signed-off-by: Alan Mizrahi <alan@mizrahi.com.ve>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a LED flash class driver for the as3654a flash controller. A V4L2 flash
driver for it already exists (drivers/media/i2c/as3645a.c), and this driver
is based on that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
SEAD3 is using the generic syscon & regmap based register-bit-led
driver as of commit c764583f40b8 ("MIPS: SEAD3: Use register-bit-led
driver via DT for LEDs") merged in the v4.9 cycle. As such the custom
SEAD-3 LED driver is now unused, so remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
All users of the Versatile LED driver are deleted and replaced
with the very generic leds-syscon. Delete the old driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
Motorola CPCAP is a PMIC (power management integrated circuit) found
in multiple smartphones. This driver adds support for the chip's LED
controllers. This introduces support for all controllers used by the
Droid 4. According to Motorola's driver (no datasheets available)
there a couple of more LED controllers. I did not add support for
them, since I cannot verify that they work with my modifications.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
MT6323 PMIC is a multi-function device that includes LED function.
It allows attaching up to 4 LEDs which can either be on, off or dimmed
and/or blinked with the controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
The dell-led driver handles a specific WMI GUID present on some Dell
laptops and as such it belongs in the x86 platform driver subsystem.
Source code is moved along with the relevant Kconfig and Makefile
entries, with some minor modifications:
- Kconfig option is renamed from CONFIG_LEDS_DELL_NETBOOKS to
CONFIG_DELL_WMI_LED,
- the X86 Kconfig dependency is removed as the whole
drivers/platform/x86 menu depends on it, so there is no need to
duplicate it,
- the name of the module's source file is removed from the header
comment to avoid the need to update it in the future.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
Add the driver to support User LEDs on PXI Embedded Controller.
Signed-off-by: Hui Chun Ong <hui.chun.ong@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This driver creates a userspace leds driver similar to uinput.
New LEDs are created by opening /dev/uleds and writing a uleds_user_dev
struct. A new LED class device is registered with the name given in the
struct. Reading will return a single byte that is the current brightness.
The poll() syscall is also supported. It will be triggered whenever the
brightness changes. Closing the file handle to /dev/uleds will remove
the leds class device.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This makes it possible to create a set of LEDs for Mellanox systems:
"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410",
"msb7800", "msn2740", "msn2100".
Driver obtains LED devices according to system configuration, provided
through system DMI data, like mlxcpld:fan1:green, mlxcpld:fan1:red and
creates devices in form: "devicename:colour:function".
LED setting is controlled through on board CPLD Lattice device.
For setting particular LED off, solid, blink:
echo 0 > /sys/class/leds/mlxcpld\:status\:green/brightness
echo 1 > /sys/class/leds/mlxcpld\:status\:green/brightness
echo timer > /sys/class/leds/mlxcpld\:status\:green/trigger
On module probing all LEDs are set green, on removing - off.
Last setting overwrites previous, f.e. sequence for
changing LED from green - red - green:
echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness
echo 1 > /sys/class/leds/mlxcpld\:psu\:red/brightness
echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness
Note: LEDs cannot be turned on/off simultaneously.
The Kconfig currently controlling compilation of this code is:
drivers/leds/Kconfig:config LEDS_MLXCPLD
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This adds a driver for the six PM8058 LEDs, three ordinary LEDs,
two "flash" LEDs and one "keypad" LED.
The "keypad" and "flash" LEDs are not really hard-wired to these
usecases: for example on the APQ8060 Dragonboard, the "keypad"
LED is instead used to drive an IR LED used for the proximity
sensor. The "flash" LEDs are just ordinary high-current LED
drivers.
Cc: linux-arm-msm@vger.kernel.org
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This is a driver for the Integrated Silicon Solution Inc. LED driver
chips series IS31FL319x. They can drive 1, 3, 6 or up to 9
LEDs.
Each LED is individually controllable in brightness (through pwm)
in 256 steps so that RGB LEDs can show any of ca. 16 Mio colors.
The maximum current of the LEDs can be programmed and limited to
5 .. 40mA through a device tree property.
The chip is connected through I2C and can have one of 4 addresses
in the range 0x64 .. 0x67 depending on how the AD pin is connected. The
address is defined by the reg property as usual.
The chip also has a shutdown input which could be connected to a GPIO,
but this driver uses software shutdown if all LEDs are inactivated.
The chip also has breathing and audio features which are not fully
supported by this driver.
Tested-on: OMAP5 based Pyra handheld prototype.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The chip can drive 2 sets of RGB leds. Controller can
be controlled via PWM, I2C and audio synchronisation.
This driver uses I2C to communicate with the chip.
Datasheet: http://www.ti.com/lit/gpn/lp3952
Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The IS31FL32xx family of LED controllers are I2C devices with multiple
constant-current channels, each with independent 256-level PWM control.
Datasheets: http://www.issi.com/US/product-analog-fxled-driver.shtml
This has been tested on the IS31FL3236 and IS31FL3216, on an ARM
(TI am335x) platform.
The programming paradigm of these devices is similar in the following
ways:
- All registers are 8 bit
- All LED control registers are write-only
- Each LED channel has a PWM register (0-255)
- PWM register writes are shadowed until an Update register is poked
- All have a concept of Software Shutdown, which disables output
However, there are some differences in devices:
- 3236/3235 have a separate Control register for each LED,
(3218/3216 pack the enable bits into fewer registers)
- 3236/3235 have a per-channel current divisor setting
- 3236/3235 have a Global Control register that can turn off all LEDs
- 3216 is unique in a number of ways
- OUT9-OUT16 can be configured as GPIOs instead of LED controls
- LEDs can be programmed with an 8-frame animation, with
programmable delay between frames
- LEDs can be modulated by an input audio signal
- Max output current can be adjusted from 1/4 to 2x globally
- Has a Configuration register instead of a Shutdown register
This driver currently only supports the base PWM control function
of these devices. The following features of these devices are not
implemented, although it should be possible to add them in the future:
- All devices are capable of going into a lower-power "software
shutdown" mode.
- The is31fl3236 and is31fl3235 can reduce the max output current
per-channel with a divisor of 1, 2, 3, or 4.
- The is31fl3216 can use some LED channels as GPIOs instead.
- The is31fl3216 can animate LEDs in hardware.
- The is31fl3216 can modulate LEDs according to an audio input.
- The is31fl3216 can reduce/increase max output current globally.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Fixes the following randconfig problem
leds-sead3.c:(.text+0x7dc): undefined reference to `led_classdev_unregister'
leds-sead3.c:(.text+0x7e8): undefined reference to `led_classdev_unregister'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-leds@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Stop using LP855X Platform Data to control regulators
- Move PWM8941 WLED driver into Backlight
- Remove invalid use of IS_ERR_VALUE() macro
- Remove duplicate check for NULL data before unregistering
- Export I2C Device ID structure
* tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: tosa: Export I2C module alias information
backlight: lp8788_bl: Delete a check before backlight_device_unregister()
backlight: sky81452: Remove unneeded use of IS_ERR_VALUE() macro
backlight: pm8941-wled: Move PM8941 WLED driver to backlight
backlight: lp855x: Use private data for regulator control
|
|
The Qualcomm PM8941 WLED block is used for backlight and should therefor
be in the backlight framework and not in the LED framework. This moves
the driver and adapts to the backlight api instead.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch implements LED driver for PowerNV platform using the existing
generic LED class framework.
PowerNV platform has below type of LEDs:
- System attention
Indicates there is a problem with the system that needs attention.
- Identify
Helps the user locate/identify a particular FRU or resource in the
system.
- Fault
Indicates there is a problem with the FRU or resource at the
location with which the indicator is associated.
We register classdev structures for all individual LEDs detected on the
system through LED specific device tree nodes. Device tree nodes specify
what all kind of LEDs present on the same location code. It registers
LED classdev structure for each of them.
All the system LEDs can be found in the same regular path /sys/class/leds/.
We don't use LED colors. We use LED node and led-types property to form
LED classdev. Our LEDs have names in this format.
<location_code>:<attention|identify|fault>
Any positive brightness value would turn on the LED and a zero value would
turn off the LED. The driver will return LED_FULL (255) for any turned on
LED and LED_OFF (0) for any turned off LED.
The platform level implementation of LED get and set state has been
achieved through OPAL calls. These calls are made available for the
driver by exporting from architecture specific codes.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This adds support for the LED controller on Broadcom's BCM6358.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch adds a driver to support the ktd2692 flash LEDs.
ktd2692 can control flash current by ExpressWire interface.
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This adds support for the LED controller on Broadcom's BCM6328.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch adds a driver for the 1.5A Step-Up Current Regulator
for Flash LEDs. The device is programmed through a Skyworks proprietary
AS2Cwire serial digital interface.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch adds led-flash support to Maxim max77693 chipset.
A device can be exposed to user space through LED subsystem
sysfs interface. Device supports up to two leds which can
work in flash and torch mode. The leds can be triggered
externally or by software.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
The TLC59116 is an I2C bus controlled 16-channel LED driver. The
TLC59108 is an I2C bus controlled 8-channel LED driver, which is very
similar to the TLC59116. Each LED output has its own 8-bit
fixed-frequency PWM controller to control the brightness of the LED.
The LEDs can also be fixed off and on, making them suitable for use as
GPOs.
This is based on a driver from Belkin, but has been extensively
rewritten and extended to support both 08 and 16 versions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Matthew.Fatheree@belkin.com
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This adds support for the WLED ('White' LED) block on Qualcomm's
PM8941 PMICs.
(cooloney@gmail.com: remove unneeded semicolon)
Signed-off-by: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
