summaryrefslogtreecommitdiffstats
path: root/drivers/irqchip/Kconfig
AgeCommit message (Collapse)AuthorFilesLines
2017-07-05Merge tag 'arm64-upstream' of ↵Linus Torvalds1-1/+0
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 updates from Will Deacon: - RAS reporting via GHES/APEI (ACPI) - Indirect ftrace trampolines for modules - Improvements to kernel fault reporting - Page poisoning - Sigframe cleanups and preparation for SVE context - Core dump fixes - Sparse fixes (mainly relating to endianness) - xgene SoC PMU v3 driver - Misc cleanups and non-critical fixes * tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (75 commits) arm64: fix endianness annotation for 'struct jit_ctx' and friends arm64: cpuinfo: constify attribute_group structures. arm64: ptrace: Fix incorrect get_user() use in compat_vfp_set() arm64: ptrace: Remove redundant overrun check from compat_vfp_set() arm64: ptrace: Avoid setting compat FP[SC]R to garbage if get_user fails arm64: fix endianness annotation for __apply_alternatives()/get_alt_insn() arm64: fix endianness annotation in get_kaslr_seed() arm64: add missing conversion to __wsum in ip_fast_csum() arm64: fix endianness annotation in acpi_parking_protocol.c arm64: use readq() instead of readl() to read 64bit entry_point arm64: fix endianness annotation for reloc_insn_movw() & reloc_insn_imm() arm64: fix endianness annotation for aarch64_insn_write() arm64: fix endianness annotation in aarch64_insn_read() arm64: fix endianness annotation in call_undef_hook() arm64: fix endianness annotation for debug-monitors.c ras: mark stub functions as 'inline' arm64: pass endianness info to sparse arm64: ftrace: fix !CONFIG_ARM64_MODULE_PLTS kernels arm64: signal: Allow expansion of the signal frame acpi: apei: check for pending errors when probing GHES entries ...
2017-06-23irqchip/irq-mvebu-icu: Add new driver for Marvell ICUThomas Petazzoni1-0/+3
The Marvell ICU unit is found in the CP110 block of the Marvell Armada 7K and 8K SoCs. It collects the wired interrupts of the devices located in the CP110 and turns them into SPI interrupts in the GIC located in the AP806 side of the SoC, by using a memory transaction. Until now, the ICU was configured in a static fashion by the firmware, and Linux was relying on this static configuration. By having Linux configure the ICU, we are more flexible, and we can allocate dynamically the GIC SPI interrupts only for devices that are actually in use. The driver was initially written by Hanna Hawa <hannah@marvell.com>. Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2017-06-23irqchip/irq-mvebu-gicp: Add new driver for Marvell GICPThomas Petazzoni1-0/+3
This commit adds a simple driver for the Marvell GICP, a hardware unit that converts memory writes into GIC SPI interrupts. The driver provides a number of functions to the ICU driver to allocate GICP interrupts, and get the physical addresses that the ICUs should write to to set/clear interrupts. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2017-06-15ARM64/irqchip: Update ACPI_IORT symbol selection logicLorenzo Pieralisi1-1/+0
ACPI IORT is an ACPI addendum to describe the connection topology of devices with IOMMUs and interrupt controllers on ARM64 ACPI systems. Currently the ACPI IORT Kbuild symbol is selected whenever the Kbuild symbol ARM_GIC_V3_ITS is enabled, which in turn is selected by ARM64 Kbuild defaults. This makes the logic behind ACPI_IORT selection a bit twisted and not easy to follow. On ARM64 systems enabling ACPI the kbuild symbol ACPI_IORT should always be selected in that it is a kernel layer provided to the ARM64 arch code to parse and enable ACPI firmware bindings. Make the ACPI_IORT selection explicit in ARM64 Kbuild and remove the selection from ARM_GIC_V3_ITS entry, making the ACPI_IORT selection logic clearer to follow. Acked-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Hanjun Guo <hanjun.guo@linaro.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-05-12Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds1-0/+2
Pull MIPS updates from James Hogan: "math-emu: - Add missing clearing of BLTZALL and BGEZALL emulation counters - Fix BC1EQZ and BC1NEZ condition handling - Fix BLEZL and BGTZL identification BPF: - Add JIT support for SKF_AD_HATYPE - Use unsigned access for unsigned SKB fields - Quit clobbering callee saved registers in JIT code - Fix multiple problems in JIT skb access helpers Loongson 3: - Select MIPS_L1_CACHE_SHIFT_6 Octeon: - Remove vestiges of CONFIG_CAVIUM_OCTEON_2ND_KERNEL - Remove unused L2C types and macros. - Remove unused SLI types and macros. - Fix compile error when USB is not enabled. - Octeon: Remove unused PCIERCX types and macros. - Octeon: Clean up platform code. SNI: - Remove recursive include of cpu-feature-overrides.h Sibyte: - Export symbol periph_rev to sb1250-mac network driver. - Fix Kconfig warning. Generic platform: - Enable Root FS on NFS in generic_defconfig SMP-MT: - Use CPU interrupt controller IPI IRQ domain support UASM: - Add support for LHU for uasm. - Remove needless ISA abstraction mm: - Add 48-bit VA space and 4-level page tables for 4K pages. PCI: - Add controllers before the specified head irqchip driver for MIPS CPU: - Replace magic 0x100 with IE_SW0 - Prepare for non-legacy IRQ domains - Introduce IPI IRQ domain support MAINTAINERS: - Update email-id of Rahul Bedarkar NET: - sb1250-mac: Add missing MODULE_LICENSE() CPUFREQ: - Loongson2: drop set_cpus_allowed_ptr() Misc: - Disable Werror when W= is set - Opt into HAVE_COPY_THREAD_TLS - Enable GENERIC_CPU_AUTOPROBE - Use common outgoing-CPU-notification code - Remove dead define of ST_OFF - Remove CONFIG_ARCH_HAS_ILOG2_U{32,64} - Stengthen IPI IRQ domain sanity check - Remove confusing else statement in __do_page_fault() - Don't unnecessarily include kmalloc.h into <asm/cache.h>. - Delete unused definition of SMP_CACHE_SHIFT. - Delete redundant definition of SMP_CACHE_BYTES" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (39 commits) MIPS: Sibyte: Fix Kconfig warning. MIPS: Sibyte: Export symbol periph_rev to sb1250-mac network driver. NET: sb1250-mac: Add missing MODULE_LICENSE() MAINTAINERS: Update email-id of Rahul Bedarkar MIPS: Remove confusing else statement in __do_page_fault() MIPS: Stengthen IPI IRQ domain sanity check MIPS: smp-mt: Use CPU interrupt controller IPI IRQ domain support irqchip: mips-cpu: Introduce IPI IRQ domain support irqchip: mips-cpu: Prepare for non-legacy IRQ domains irqchip: mips-cpu: Replace magic 0x100 with IE_SW0 MIPS: Remove CONFIG_ARCH_HAS_ILOG2_U{32,64} MIPS: generic: Enable Root FS on NFS in generic_defconfig MIPS: mach-rm: Remove recursive include of cpu-feature-overrides.h MIPS: Opt into HAVE_COPY_THREAD_TLS CPUFREQ: Loongson2: drop set_cpus_allowed_ptr() MIPS: uasm: Remove needless ISA abstraction MIPS: Remove dead define of ST_OFF MIPS: Use common outgoing-CPU-notification code MIPS: math-emu: Fix BC1EQZ and BC1NEZ condition handling MIPS: r2-on-r6-emu: Clear BLTZALL and BGEZALL debugfs counters ...
2017-04-20Merge branch 'linus' into irq/coreThomas Gleixner1-0/+1
Pick up upstream fixes to avoid conflicts with pending patches.
2017-04-12irqchip: mips-cpu: Introduce IPI IRQ domain supportPaul Burton1-0/+2
Introduce support for registering an IPI IRQ domain suitable for use by systems using the MIPS MT (multithreading) ASE within a single core. This will allow for such systems to be supported generically, without the current kludge of IPI code split between the MIPS arch & the malta board support code. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15836/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-04-07irqchip/gemini: Refactor Gemini driver to reflect Faraday originLinus Walleij1-0/+6
The Gemini irqchip turns out to be a standard IP component from Faraday Technology named FTINTC010 after some research and new information. - Rename the driver and all symbols to reflect the new information. - Add the new compatible string "faraday,ftintc010" - Create a Kconfig symbol CONFIG_FARADAY_FTINTC010 so that SoCs using this interrupt controller can easily select and reuse it instead of hardwiring it to ARCH_GEMINI I have created a separate patch to select the new Kconfig symbol from the Gemini machine, which will be merged through the ARM SoC tree. Cc: Greentime Hu <green.hu@gmail.com> Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2017-03-14irqchip/mvebu-odmi: Select GENERIC_MSI_IRQ_DOMAINArnd Bergmann1-0/+1
This driver uses the MSI domain but has no strict dependency on PCI_MSI, so we may run into a build failure when CONFIG_GENERIC_MSI_IRQ_DOMAIN is disabled: drivers/irqchip/irq-mvebu-odmi.c:152:15: error: variable 'odmi_msi_ops' has initializer but incomplete type static struct msi_domain_ops odmi_msi_ops = { ^~~~~~~~~~~~~~ drivers/irqchip/irq-mvebu-odmi.c:155:15: error: variable 'odmi_msi_domain_info' has initializer but incomplete type static struct msi_domain_info odmi_msi_domain_info = { ^~~~~~~~~~~~~~~ drivers/irqchip/irq-mvebu-odmi.c:156:3: error: 'struct msi_domain_info' has no member named 'flags' .flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS), ^~~~~ drivers/irqchip/irq-mvebu-odmi.c:156:12: error: 'MSI_FLAG_USE_DEF_DOM_OPS' undeclared here (not in a function) .flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS), ^~~~~~~~~~~~~~~~~~~~~~~~ drivers/irqchip/irq-mvebu-odmi.c:156:39: error: 'MSI_FLAG_USE_DEF_CHIP_OPS' undeclared here (not in a function); did you mean 'MSI_FLAG_USE_DEF_DOM_OPS'? Selecting the option from this driver seems to solve this nicely, though I could not find any other instance of this in irqchip drivers. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2017-02-03irqchip/qcom: Add IRQ combiner driverAgustin Vega-Frias1-0/+9
Driver for interrupt combiners in the Top-level Control and Status Registers (TCSR) hardware block in Qualcomm Technologies chips. An interrupt combiner in this block combines a set of interrupts by OR'ing the individual interrupt signals into a summary interrupt signal routed to a parent interrupt controller, and provides read- only, 32-bit registers to query the status of individual interrupts. The status bit for IRQ n is bit (n % 32) within register (n / 32) of the given combiner. Thus, each combiner can be described as a set of register offsets and the number of IRQs managed. Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-11-29microblaze/irqchip: Move intc driver to irqchipZubair Lutfullah Kakakhel1-0/+4
The Xilinx AXI Interrupt Controller IP block is used by the MIPS based xilfpga platform and a few PowerPC based platforms. Move the interrupt controller code out of arch/microblaze so that it can be used by everyone Tested-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-10-20irqchip/jcore: Don't show Kconfig menu item for driverRich Felker1-2/+2
Core drivers for J-Core SoCs will be selected implicitly via CONFIG_SH_JCORE_SOC instead. Based on a corresponding change to the clocksource/timer driver requested by Daniel Lezcano. Signed-off-by: Rich Felker <dalias@libc.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: linux-sh@vger.kernel.org Link: http://lkml.kernel.org/r/883a3d17084003e3cf21bab73ec12828fe4ff6c6.1476899495.git.dalias@libc.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-09-22Merge tag 'irqchip-core-4.9' of git://git.infradead.org/users/jcooper/linux ↵Thomas Gleixner1-0/+10
into irq/core Pull irqchip core changes for v4.9 from Jason Cooper - jcore: Add AIC driver - mips-gic: Use for_each_set_bit - mvebu: Add PIC driver
2016-09-21drivers/irqchip: Add STM32 external interrupts supportAlexandre TORGUE1-0/+4
The STM32 external interrupt controller consists of edge detectors that generate interrupts requests or wake-up events. Each line can be independently configured as interrupt or wake-up source, and triggers either on rising, falling or both edges. Each line can also be masked independently. Originally-from: Maxime Coquelin <mcoquelin.stm32@gmail.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Jason Cooper <jason@lakedaemon.net> Cc: arnd@arndb.de Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: bruherrera@gmail.com Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-gpio@vger.kernel.org Cc: Rob Herring <robh+dt@kernel.org> Cc: lee.jones@linaro.org Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1474387259-18926-3-git-send-email-alexandre.torgue@st.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-09-12irqchip/gicv3-its: Probe ITS in the ACPI wayTomasz Nowicki1-0/+1
ITS is prepared for being initialized different than DT, therefore we can initialize it in ACPI way. We collect register base address from MADT table and pass mandatory info to firmware-agnostic ITS init call. Use here IORT lib to register ITS domain which then can be found and used on to build another PCI MSI domain in hierarchical stack domain. NOTE: Waiting for proper ITS and NUMA node relation description in IORT table, we pass around NUMA_NO_NODE to the its_probe_one init call. This means that Cavium ThunderX erratum 23144 (pass1.1 only) is not supported for ACPI boot method yet. Signed-off-by: Tomasz Nowicki <tn@semihalf.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-08-23Merge branch 'irqchip/mvebu64' into irqchip/coreJason Cooper1-0/+3
2016-08-22irqchip/mvebu-pic: New driver for Marvell Armada 7K/8K PICThomas Petazzoni1-0/+3
The Marvell Armada 7K/8K integrates a secondary interrupt controller very originally named "PIC". It is connected to the main GIC via a PPI. Amongst other things, this PIC is used for the ARM PMU. This commit adds a simple irqchip driver for this interrupt controller. Since this interrupt controller is not needed early at boot time, we make the driver a proper platform driver rather than use the IRQCHIP_DECLARE() mechanism. Signed-off-by: Yehuda Yitschak <yehuday@marvell.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Link: https://lkml.kernel.org/r/1470408921-447-3-git-send-email-thomas.petazzoni@free-electrons.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2016-08-08irqchip/jcore-aic: Add J-Core AIC driverRich Felker1-0/+7
There are two versions of the J-Core interrupt controller in use, aic1 which generates interrupts with programmable priorities, but only supports 8 irq lines and maps them to cpu traps in the range 17 to 24, and aic2 which uses traps in the range 64-127 and supports up to 128 irqs, with priorities dependent on the interrupt number. The Linux driver does not make use of priorities anyway. For simplicity, there is no aic1-specific logic in the driver beyond setting the priority register, which is necessary for interrupts to work at all. Eventually aic1 will likely be phased out, but it's currently in use in deployments and all released bitstream binaries. Signed-off-by: Rich Felker <dalias@libc.org> Link: https://lkml.kernel.org/r/c3b89ef74aaa6477575dbe2d410eb1d182503243.147018b6529.git.dalias@libc.org Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2016-08-02Merge tag 'pci-v4.8-changes' of ↵Linus Torvalds1-10/+8
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "Highlights: - ARM64 support for ACPI host bridges - new drivers for Axis ARTPEC-6 and Marvell Aardvark - new pci_alloc_irq_vectors() interface for MSI-X, MSI, legacy INTx - pci_resource_to_user() cleanup (more to come) Detailed summary: Enumeration: - Move ecam.h to linux/include/pci-ecam.h (Jayachandran C) - Add parent device field to ECAM struct pci_config_window (Jayachandran C) - Add generic MCFG table handling (Tomasz Nowicki) - Refactor pci_bus_assign_domain_nr() for CONFIG_PCI_DOMAINS_GENERIC (Tomasz Nowicki) - Factor DT-specific pci_bus_find_domain_nr() code out (Tomasz Nowicki) Resource management: - Add devm_request_pci_bus_resources() (Bjorn Helgaas) - Unify pci_resource_to_user() declarations (Bjorn Helgaas) - Implement pci_resource_to_user() with pcibios_resource_to_bus() (microblaze, powerpc, sparc) (Bjorn Helgaas) - Request host bridge window resources (designware, iproc, rcar, xgene, xilinx, xilinx-nwl) (Bjorn Helgaas) - Make PCI I/O space optional on ARM32 (Bjorn Helgaas) - Ignore write combining when mapping I/O port space (Bjorn Helgaas) - Claim bus resources on MIPS PCI_PROBE_ONLY set-ups (Bjorn Helgaas) - Remove unicore32 pci=firmware command line parameter handling (Bjorn Helgaas) - Support I/O resources when parsing host bridge resources (Jayachandran C) - Add helpers to request/release memory and I/O regions (Johannes Thumshirn) - Use pci_(request|release)_mem_regions (NVMe, lpfc, GenWQE, ethernet/intel, alx) (Johannes Thumshirn) - Extend pci=resource_alignment to specify device/vendor IDs (Koehrer Mathias (ETAS/ESW5)) - Add generic pci_bus_claim_resources() (Lorenzo Pieralisi) - Claim bus resources on ARM32 PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi) - Remove ARM32 and ARM64 arch-specific pcibios_enable_device() (Lorenzo Pieralisi) - Add pci_unmap_iospace() to unmap I/O resources (Sinan Kaya) - Remove powerpc __pci_mmap_set_pgprot() (Yinghai Lu) PCI device hotplug: - Allow additional bus numbers for hotplug bridges (Keith Busch) - Ignore interrupts during D3cold (Lukas Wunner) Power management: - Enforce type casting for pci_power_t (Andy Shevchenko) - Don't clear d3cold_allowed for PCIe ports (Mika Westerberg) - Put PCIe ports into D3 during suspend (Mika Westerberg) - Power on bridges before scanning new devices (Mika Westerberg) - Runtime resume bridge before rescan (Mika Westerberg) - Add runtime PM support for PCIe ports (Mika Westerberg) - Remove redundant check of pcie_set_clkpm (Shawn Lin) Virtualization: - Add function 1 DMA alias quirk for Marvell 88SE9182 (Aaron Sierra) - Add DMA alias quirk for Adaptec 3805 (Alex Williamson) - Mark Atheros AR9485 and QCA9882 to avoid bus reset (Chris Blake) - Add ACS quirk for Solarflare SFC9220 (Edward Cree) MSI: - Fix PCI_MSI dependencies (Arnd Bergmann) - Add pci_msix_desc_addr() helper (Christoph Hellwig) - Switch msix_program_entries() to use pci_msix_desc_addr() (Christoph Hellwig) - Make the "entries" argument to pci_enable_msix() optional (Christoph Hellwig) - Provide sensible IRQ vector alloc/free routines (Christoph Hellwig) - Spread interrupt vectors in pci_alloc_irq_vectors() (Christoph Hellwig) Error Handling: - Bind DPC to Root Ports as well as Downstream Ports (Keith Busch) - Remove DPC tristate module option (Keith Busch) - Convert Downstream Port Containment driver to use devm_* functions (Mika Westerberg) Generic host bridge driver: - Select IRQ_DOMAIN (Arnd Bergmann) - Claim bus resources on PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi) ACPI host bridge driver: - Add ARM64 acpi_pci_bus_find_domain_nr() (Tomasz Nowicki) - Add ARM64 ACPI support for legacy IRQs parsing and consolidation with DT code (Tomasz Nowicki) - Implement ARM64 AML accessors for PCI_Config region (Tomasz Nowicki) - Support ARM64 ACPI-based PCI host controller (Tomasz Nowicki) Altera host bridge driver: - Check link status before retrain link (Ley Foon Tan) - Poll for link up status after retraining the link (Ley Foon Tan) Axis ARTPEC-6 host bridge driver: - Add PCI_MSI_IRQ_DOMAIN dependency (Arnd Bergmann) - Add DT binding for Axis ARTPEC-6 PCIe controller (Niklas Cassel) - Add Axis ARTPEC-6 PCIe controller driver (Niklas Cassel) Intel VMD host bridge driver: - Use lock save/restore in interrupt enable path (Jon Derrick) - Select device dma ops to override (Keith Busch) - Initialize list item in IRQ disable (Keith Busch) - Use x86_vector_domain as parent domain (Keith Busch) - Separate MSI and MSI-X vector sharing (Keith Busch) Marvell Aardvark host bridge driver: - Add DT binding for the Aardvark PCIe controller (Thomas Petazzoni) - Add Aardvark PCI host controller driver (Thomas Petazzoni) - Add Aardvark PCIe support for Armada 3700 (Thomas Petazzoni) Microsoft Hyper-V host bridge driver: - Fix interrupt cleanup path (Cathy Avery) - Don't leak buffer in hv_pci_onchannelcallback() (Vitaly Kuznetsov) - Handle all pending messages in hv_pci_onchannelcallback() (Vitaly Kuznetsov) NVIDIA Tegra host bridge driver: - Program PADS_REFCLK_CFG* always, not just on legacy SoCs (Stephen Warren) - Program PADS_REFCLK_CFG* registers with per-SoC values (Stephen Warren) - Use lower-case hex consistently for register definitions (Thierry Reding) - Use generic pci_remap_iospace() rather than ARM32-specific one (Thierry Reding) - Stop setting pcibios_min_mem (Thierry Reding) Renesas R-Car host bridge driver: - Drop gen2 dummy I/O port region (Bjorn Helgaas) TI DRA7xx host bridge driver: - Fix return value in case of error (Christophe JAILLET) Xilinx AXI host bridge driver: - Fix return value in case of error (Christophe JAILLET) Miscellaneous: - Make bus_attr_resource_alignment static (Ben Dooks) - Include <asm/dma.h> for isa_dma_bridge_buggy (Ben Dooks) - MAINTAINERS: Add file patterns for PCI device tree bindings (Geert Uytterhoeven) - Make host bridge drivers explicitly non-modular (Paul Gortmaker)" * tag 'pci-v4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (125 commits) PCI: xgene: Make explicitly non-modular PCI: thunder-pem: Make explicitly non-modular PCI: thunder-ecam: Make explicitly non-modular PCI: tegra: Make explicitly non-modular PCI: rcar-gen2: Make explicitly non-modular PCI: rcar: Make explicitly non-modular PCI: mvebu: Make explicitly non-modular PCI: layerscape: Make explicitly non-modular PCI: keystone: Make explicitly non-modular PCI: hisi: Make explicitly non-modular PCI: generic: Make explicitly non-modular PCI: designware-plat: Make it explicitly non-modular PCI: artpec6: Make explicitly non-modular PCI: armada8k: Make explicitly non-modular PCI: artpec: Add PCI_MSI_IRQ_DOMAIN dependency PCI: Add ACS quirk for Solarflare SFC9220 arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700 PCI: aardvark: Add Aardvark PCI host controller driver dt-bindings: add DT binding for the Aardvark PCIe controller PCI: tegra: Program PADS_REFCLK_CFG* registers with per-SoC values ...
2016-06-15PCI/MSI: irqchip: Fix PCI_MSI dependenciesArnd Bergmann1-10/+8
The PCI_MSI symbol is used inconsistently throughout the tree, with some drivers using 'select' and others using 'depends on', or using conditional selects. This keeps causing problems; the latest one is a result of ARCH_ALPINE using a 'select' statement to enable its platform-specific MSI driver without enabling MSI: warning: (ARCH_ALPINE) selects ALPINE_MSI which has unmet direct dependencies (PCI && PCI_MSI) drivers/irqchip/irq-alpine-msi.c:104:15: error: variable 'alpine_msix_domain_info' has initializer but incomplete type static struct msi_domain_info alpine_msix_domain_info = { ^~~~~~~~~~~~~~~ drivers/irqchip/irq-alpine-msi.c:105:2: error: unknown field 'flags' specified in initializer .flags = MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS | ^ drivers/irqchip/irq-alpine-msi.c:105:11: error: 'MSI_FLAG_USE_DEF_DOM_OPS' undeclared here (not in a function) .flags = MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS | ^~~~~~~~~~~~~~~~~~~~~~~~ There is little reason to enable PCI support for a platform that uses MSI but then leave MSI disabled at compile time. Select PCI_MSI from irqchips that implement MSI, and make PCI host bridges that use MSI on ARM depend on PCI_MSI_IRQ_DOMAIN. For all three architectures that support PCI_MSI_IRQ_DOMAIN (ARM, ARM64, X86), enable it by default whenever MSI is enabled. [bhelgaas: changelog, omit crypto config change] Suggested-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com>
2016-06-13irqchip/gic: Add platform driver for non-root GICs that require RPMJon Hunter1-0/+6
Add a platform driver to support non-root GICs that require runtime power-management. Currently, only non-root GICs are supported because the functions, smp_cross_call() and set_handle_irq(), that need to be called for a root controller are located in the __init section and so cannot be called by the platform driver. The GIC platform driver re-uses many functions from the existing GIC driver including some functions to save and restore the GIC context during power transitions. The functions for saving and restoring the GIC context are currently only defined if CONFIG_CPU_PM is enabled and to ensure that these functions are always defined when the platform driver is enabled, a dependency on CONFIG_ARM_GIC_PM (which selects the platform driver) has been added. In order to re-use the private GIC initialisation code, a new public function, gic_of_init_child(), has been added which calls various private functions to initialise the GIC. This is different from the existing gic_of_init() because it only supports non-root GICs (ie. does not call smp_cross_call() is set_handle_irq()) and is not located in the __init section (so can be used by platform drivers). Furthermore, gic_of_init_child() dynamically allocates memory for the GIC chip data which is also different from gic_of_init(). There is no specific suspend handling for GICs registered as platform devices. Non-wakeup interrupts will be disabled by the kernel during late suspend, however, this alone will not power down the GIC if interrupts have been requested and not freed. Therefore, requestors of non-wakeup interrupts will need to free them on entering suspend in order to power-down the GIC. Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-05-20irqchip: nps: add 64BIT dependencyArnd Bergmann1-0/+1
The newly added nps irqchip driver causes build warnings on ARM64. include/soc/nps/common.h: In function 'nps_host_reg_non_cl': include/soc/nps/common.h:148:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] As the driver is only used on ARC, we don't need to see it without COMPILE_TEST elsewhere, and we can avoid the warnings by only building on 32-bit architectures even with CONFIG_COMPILE_TEST. Acked-by: Marc Zyngier <narc.zyngier@arm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-05-19Merge tag 'arc-4.7-rc1' of ↵Linus Torvalds1-0/+6
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc Pull ARC updates from Vineet Gupta: "We have a relatively big changeset for ARC for 4.7. The highlight is support for EZChip (now Mellanox) NPS-400 network processor, a 400-Gb throughput C-programmable packet processor based on ARC700 cores from Synopsys. See http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf Also present are irqchip and clocksource drivers for NPS as agreed with respective maintainers to go via ARC tree due to an soc header dependency. I have the needed ACKs from Jason, Marc, Daniel. You might run into a trivial merge conflict in drivers/irqchip/* This EZChip platform support required some deep changes in ARC architecture code and also opportunity to cleanup past sins (legacy irq domains, missing irq domain lookup, hard coded timer irqs...) Summary: - Support for EZChip (now Mellanox) NPS-400 Network processor based on ARC700 - NPS interrupt controller and clocksource drivers - ARC timers probed off DT - ARC iqrchips switching to linear domain (upgrade from legacy domains)" * tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (37 commits) arc: axs103_smp: Fix CPU frequency to 100MHz for dual-core arc: axs10x: Add DT bindings for I2S PLL Clock ARC: pae: STRICT_MM_TYPECHECKS was broken ARC: Add eznps platform to Kconfig and Makefile ARC: [plat-eznps] Use dedicated COMMAND_LINE_SIZE ARC: [plat-eznps] Use dedicated cpu_relax() ARC: [plat-eznps] Use dedicated identity auxiliary register. ARC: [plat-eznps] Use dedicated SMP barriers ARC: [plat-eznps] Use dedicated atomic/bitops/cmpxchg ARC: [plat-eznps] Use dedicated user stack top ARC: [plat-eznps] Add eznps platform ARC: [plat-eznps] Add eznps board defconfig and dts ARC: Mark secondary cpu online only after all HW setup is done ARC: rwlock: disable interrupts in !LLSC variant ARC: Make vmalloc size configurable ARC: clean out UAPI byteorder.h clean off Kconfig symbol irqchip: add nps Internal and external irqchips clocksource: Add NPS400 timers driver soc: Support for EZchip SoC Documentation: Add EZchip vendor to binding list ...
2016-05-09irqchip: add nps Internal and external irqchipsNoam Camus1-0/+6
Adding EZchip NPS400 support. Internal interrupts are handled by Multi Thread Manager (MTM) Once interrupt is serviced MTM is acked for deactivating the interrupt. External interrupts are handled by MTM as well as at Global Interrupt Controller (GIC) e.g. serial and network devices. Signed-off-by: Noam Camus <noamc@ezchip.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Vineet Gupta <vgupta@synopsys.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Cc: Thomas Gleixner <tglx@linutronix.de>
2016-05-04irqchip: Add Layerscape SCFG MSI controller supportMinghuan Lian1-0/+5
Some kind of Freescale Layerscape SoC provides a MSI implementation which uses two SCFG registers MSIIR and MSIR to support 32 MSI interrupts for each PCIe controller. The patch is to support it. Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com> Tested-by: Alexander Stein <alexander.stein@systec-electronic.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-05-02irqchip/gic-v3: Add support for partitioned PPIsMarc Zyngier1-0/+1
Plug the partitioning layer into the GICv3 PPI code, parsing the DT and building the partition affinities and providing the generic code with partition data and callbacks. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: Jason Cooper <jason@lakedaemon.net> Cc: Will Deacon <will.deacon@arm.com> Cc: Rob Herring <robh+dt@kernel.org> Link: http://lkml.kernel.org/r/1460365075-7316-5-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-05-02irqchip: Add per-cpu interrupt partitioning libraryMarc Zyngier1-0/+3
We've unfortunately started seeing a situation where percpu interrupts are partitioned in the system: one arbitrary set of CPUs has an interrupt connected to a type of device, while another disjoint set of CPUs has the same interrupt connected to another type of device. This makes it impossible to have a device driver requesting this interrupt using the current percpu-interrupt abstraction, as the same interrupt number is now potentially claimed by at least two drivers, and we forbid interrupt sharing on per-cpu interrupt. A solution to this is to turn things upside down. Let's assume that our system describes all the possible partitions for a given interrupt, and give each of them a unique identifier. It is then possible to create a namespace where the affinity identifier itself is a form of interrupt number. At this point, it becomes easy to implement a set of partitions as a cascaded irqchip, each affinity identifier being the HW irq. This allows us to keep a number of nice properties: - Each partition results in a separate percpu-interrupt (with a restrictied affinity), which keeps drivers happy. - Because the underlying interrupt is still per-cpu, the overhead of the indirection can be kept pretty minimal. - The core code can ignore most of that crap. For that purpose, we implement a small library that deals with some of the boilerplate code, relying on platform-specific drivers to provide a description of the affinity sets and a set of callbacks. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: Jason Cooper <jason@lakedaemon.net> Cc: Will Deacon <will.deacon@arm.com> Cc: Rob Herring <robh+dt@kernel.org> Link: http://lkml.kernel.org/r/1460365075-7316-4-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-03-23irqchip/mbigen: Make CONFIG_HISILICON_IRQ_MBIGEN a hidden optionMaJun1-8/+6
This config is selected by CONFIG_ARCH_HISI, so there is no point to have it user configurable. While at it move the config option to the proper place in the alphabetically sorted option list. Requested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ma Jun <majun258@huawei.com> Cc: mark.rutland@arm.com Cc: jason@lakedaemon.net Cc: marc.zyngier@arm.com Cc: Catalin.Marinas@arm.com Cc: guohanjun@huawei.com Cc: Will.Deacon@arm.com Cc: huxinwei@huawei.com Cc: lizefan@huawei.com Cc: dingtianhong@huawei.com Cc: zhaojunhua@hisilicon.com Cc: liguozhu@hisilicon.com Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1458723993-21044-3-git-send-email-majun258@huawei.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-03-09irqchip: Add the Alpine MSIX interrupt controllerAntoine Tenart1-0/+6
This patch adds the Alpine MSIX interrupt controller driver. Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-25MIPS: Make smp CMP, CPS and MT use the new generic IPI functionsQais Yousef1-0/+1
This commit does several things to avoid breaking bisectability. 1- Remove IPI init code from irqchip/mips-gic 2- Implement the new irqchip->send_ipi() in irqchip/mips-gic 3- Select GENERIC_IRQ_IPI Kconfig symbol for MIPS_GIC 4- Change MIPS SMP to use the generic IPI implementation Only the SMP variants that use GIC were converted as it's the only irqchip that will have the support for generic IPI for now. Signed-off-by: Qais Yousef <qais.yousef@imgtec.com> Acked-by: Ralf Baechle <ralf@linux-mips.org> Cc: <jason@lakedaemon.net> Cc: <marc.zyngier@arm.com> Cc: <jiang.liu@linux.intel.com> Cc: <linux-mips@linux-mips.org> Cc: <lisa.parratt@imgtec.com> Cc: Qais Yousef <qsyousef@gmail.com> Link: http://lkml.kernel.org/r/1449580830-23652-18-git-send-email-qais.yousef@imgtec.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-02-25irqchip/mips-gic: Add a IPI hierarchy domainQais Yousef1-0/+1
Add a new ipi domain on top of the normal domain. MIPS GIC now supports dynamic allocation of an IPI. Signed-off-by: Qais Yousef <qais.yousef@imgtec.com> Acked-by: Ralf Baechle <ralf@linux-mips.org> Cc: <jason@lakedaemon.net> Cc: <marc.zyngier@arm.com> Cc: <jiang.liu@linux.intel.com> Cc: <linux-mips@linux-mips.org> Cc: <lisa.parratt@imgtec.com> Cc: Qais Yousef <qsyousef@gmail.com> Link: http://lkml.kernel.org/r/1449580830-23652-13-git-send-email-qais.yousef@imgtec.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-02-21Merge tag 'irqchip-core-4.6-2' of ↵Thomas Gleixner1-0/+9
git://git.infradead.org/users/jcooper/linux into irq/core Pull the second round of irqchip core changes for v4.6 from Jason Cooper: - mvebu: - Add odmi driver for Marvell 7K/8K SoCs - Replace driver-specific set_affinity with generic version - mips: - Move ath79 MISC and CPU drivers from arch/ code to irqchip/ - tango: - Add support for Sigma Designs SMP8[67]xx ctrl
2016-02-21Merge tag 'irqchip-core-4.6' of git://git.infradead.org/users/jcooper/linux ↵Thomas Gleixner1-0/+6
into irq/core Pull irqchip core changes for v4.6 from Jason Cooper: - mvebu (armada-370-xp) - MSI support - Deconflict with mvebu's arm64 code - ts4800 - Restrict when ts4800 driver can be built - Make ts4800_ic_ops static const - bcm2836: Drop superfluous memory barrier
2016-02-21Merge branch 'irqchip/mvebu' into irqchip/coreJason Cooper1-0/+4
2016-02-21Merge branch 'irqchip/tango' into irqchip/coreJason Cooper1-0/+5
2016-02-19irqchip/mvebu-odmi: Add new driver for platform MSI on Marvell 7K/8KThomas Petazzoni1-0/+4
This commits adds a new irqchip driver that handles the ODMI controller found on Marvell 7K/8K processors. The ODMI controller provide MSI interrupt functionality to on-board peripherals, much like the GIC-v2m. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/1455888883-5127-1-git-send-email-thomas.petazzoni@free-electrons.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2016-02-18irqchip/ts4800: Add hardware dependencyJean Delvare1-0/+1
The Technologic Systems TS-4800 is an i.MX515 board, so its drivers are useless unless building a SOC_IMX51 kernel, except for build testing purposes. Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Damien Riegel <damien.riegel@savoirfairelinux.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/20160209111920.1ec318bd@endymion Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2016-02-18irqchip/tango: Add support for Sigma Designs SMP86xx/SMP87xx interrupt ↵Mans Rullgard1-0/+5
controller This adds support for the secondary interrupt controller used in Sigma Designs SMP86xx and SMP87xx chips. Signed-off-by: Mans Rullgard <mans@mansr.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/1453313237-18570-2-git-send-email-mans@mansr.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2016-02-16irqchip/armada-370-xp: Do not enable it by default when ARCH_MVEBU is selectedGregory CLEMENT1-1/+0
The irq-armada-370-xp driver can only be built for ARM 32 bits. The mvebu family had grown with a new ARM64 SoC which will also select the ARCH_MEVBU configuration. Since "ARM: mvebu: use the ARMADA_370_XP_IRQ option", the ARM32 mvebu SoC directly select this new option. Selecting it by default when ARCH_MEVBU is selected is no more needed. This patch removes this dependency, thanks to this, a kernel for ARM64 mvebu SoC can be built without error due this driver. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Link: https://lkml.kernel.org/r/1454951660-13289-3-git-send-email-gregory.clement@free-electrons.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2016-02-16irqchip/armada-370-xp: Use the generic MSI infrastructureThomas Petazzoni1-0/+1
This commit moves the irq-armada-370-xp driver from using the PCI-specific MSI infrastructure to the generic MSI infrastructure, to which drivers are progressively converted. In this hardware, the MSI controller is directly bundled inside the interrupt controller, so we have a single Device Tree node to which multiple IRQ domaines are attached: the wired interrupt domain and the MSI interrupt domain. In order to ensure that they can be differentiated, we have to force the bus_token of the wired interrupt domain to be DOMAIN_BUS_WIRED. The MSI domain bus_token is automatically set to the appropriate value by pci_msi_create_irq_domain(). Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Suggested-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/1455115621-22846-3-git-send-email-thomas.petazzoni@free-electrons.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2016-02-16irqchip/armada-370-xp: Add Kconfig option for the driverThomas Petazzoni1-0/+5
Instead of building the irq-armada-370-xp driver directly when CONFIG_ARCH_MVEBU is enabled, this commit introduces an intermediate CONFIG_ARMADA_370_XP_IRQ hidden Kconfig option. This allows this option to select other interrupt-related Kconfig options (which will be needed in follow-up commits) rather than having such selects done from arch/arm/mach-<foo>/. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Link: https://lkml.kernel.org/r/1455115621-22846-2-git-send-email-thomas.petazzoni@free-electrons.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2016-02-08irqchips/bmips: Add bcm6345-l1 interrupt controllerSimon Arlott1-0/+5
Add the BCM6345 interrupt controller based on the SMP-capable BCM7038 and the BCM3380 but with packed interrupt registers. Add the BCM6345 interrupt controller to a list with the existing BCM7038 so that interrupts on CPU1 are not ignored. Update the maintainers file list for BMIPS to include this driver. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Pawel Moll <pawel.moll@arm.com> Cc: linux-mips@linux-mips.org Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Kumar Gala <galak@codeaurora.org> Cc: Rob Herring <robh@kernel.org> Link: http://lkml.kernel.org/r/5651D176.6030908@simon.arlott.org.uk Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-01-31Merge branch 'irq-urgent-for-linus' of ↵Linus Torvalds1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull IRQ fixes from Ingo Molnar: "Mostly irqchip driver fixes, but also an irq core crash fix and a build fix" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/mxs: Add missing set_handle_irq() irqchip/atmel-aic: Fix wrong bit operation for IRQ priority irqchip/gic-v3-its: Recompute the number of pages on page size change base: Export platform_msi_domain_[alloc,free]_irqs of: MSI: Simplify irqdomain lookup irqdomain: Allow domain lookup with DOMAIN_BUS_WIRED token irqchip: Fix dependencies for archs w/o HAS_IOMEM irqchip/s3c24xx: Mark init_eint as __maybe_unused genirq: Validate action before dereferencing it in handle_irq_event_percpu()
2016-01-26irqchip: Fix dependencies for archs w/o HAS_IOMEMRichard Weinberger1-0/+1
Not every arch has io memory. So, unbreak the build by fixing the dependencies. Signed-off-by: Richard Weinberger <richard@nod.at> Cc: user-mode-linux-devel@lists.sourceforge.net Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Link: http://lkml.kernel.org/r/1453760661-1444-19-git-send-email-richard@nod.at Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-01-24Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds1-0/+5
Pull MIPS updates from Ralf Baechle: "This is the main pull request for MIPS for 4.5 plus some 4.4 fixes. The executive summary: - ATH79 platform improvments, use DT bindings for the ATH79 USB PHY. - Avoid useless rebuilds for zboot. - jz4780: Add NEMC, BCH and NAND device tree nodes - Initial support for the MicroChip's DT platform. As all the device drivers are missing this is still of limited use. - Some Loongson3 cleanups. - The unavoidable whitespace polishing. - Reduce clock skew when synchronizing the CPU cycle counters on CPU startup. - Add MIPS R6 fixes. - Lots of cleanups across arch/mips as fallout from KVM. - Lots of minor fixes and changes for IEEE 754-2008 support to the FPU emulator / fp-assist software. - Minor Ralink, BCM47xx and bcm963xx platform support improvments. - Support SMP on BCM63168" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits) MIPS: zboot: Add support for serial debug using the PROM MIPS: zboot: Avoid useless rebuilds MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function MIPS: bcm963xx: Update bcm_tag field image_sequence MIPS: bcm963xx: Move extended flash address to bcm_tag header file MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure MIPS: bcm63xx: nvram: Use nvram structure definition from header file MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure MAINTAINERS: Add KVM for MIPS entry MIPS: KVM: Add missing newline to kvm_err() MIPS: Move KVM specific opcodes into asm/inst.h MIPS: KVM: Use cacheops.h definitions MIPS: Break down cacheops.h definitions MIPS: Use EXCCODE_ constants with set_except_vector() MIPS: Update trap codes MIPS: Move Cause.ExcCode trap codes to mipsregs.h MIPS: KVM: Make kvm_mips_{init,exit}() static MIPS: KVM: Refactor added offsetof()s MIPS: KVM: Convert EXPORT_SYMBOL to _GPL ...
2016-01-24IRQCHIP: irq-pic32-evic: Add support for PIC32 interrupt controllerCristian Birsan1-0/+5
This adds support for the interrupt controller present on PIC32 class devices. It handles all internal and external interrupts. This controller exists outside of the CPU core and is the arbitrator of all interrupts (including interrupts from the CPU itself) before they are presented to the CPU. The following features are supported: - DT properties for EVIC and for devices/peripherals that use interrupt lines - Persistent and non-persistent interrupt handling - irqdomain and generic chip support - Configuration of external interrupt edge polarity Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com> Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12092/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2015-12-29irqchip/ts4800: Add TS-4800 interrupt controllerDamien Riegel1-0/+6
This commit adds support for the TS-4800 interrupt controller. This controller is instantiated in a companion FPGA, and multiplex interrupts for other FPGA IPs. As this component is external to the SoC, the SoC might need to reserve pins, so this controller is implemented as a platform driver and doesn't use the IRQCHIP_DECLARE construct. Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: kernel@savoirfairelinux.com Link: http://lkml.kernel.org/r/1450728683-31416-2-git-send-email-damien.riegel@savoirfairelinux.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-12-19Merge branch 'irq/gic-4.5' of ↵Thomas Gleixner1-0/+5
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core Pull the GIC related updates from Marc Zyngier: "Not a lot this time (what a relief!), but an interesting series from Linus Walleij coming out of his work converting the ARM RealView platforms to DT, and a couple of mundane fixes."
2015-12-18irqchip/mgigen: Add platform device driver for mbigen deviceMa Jun1-0/+8
Mbigen means Message Based Interrupt Generator(MBIGEN). Its a kind of interrupt controller that collects the interrupts from external devices and generate msi interrupt. Mbigen is applied to reduce the number of wire connected interrupts. As the peripherals increasing, the interrupts lines needed is increasing much, especially on the Arm64 server SOC. Therefore, the interrupt pin in GIC is not enough to cover so many peripherals. Mbigen is designed to fix this problem. Mbigen chip locates in ITS or outside of ITS. Mbigen chip hardware structure shows as below: mbigen chip |---------------------|-------------------| mgn_node0 mgn_node1 mgn_node2 | |-------| |-------|------| dev1 dev1 dev2 dev1 dev3 dev4 Each mbigen chip contains several mbigen nodes. External devices can connect to mbigen node through wire connecting way. Because a mbigen node only can support 128 interrupt maximum, depends on the interrupt lines number of devices, a device can connects to one more mbigen nodes. Also, several different devices can connect to a same mbigen node. When devices triggered interrupt,mbigen chip detects and collects the interrupts and generates the MBI interrupts by writing the ITS Translator register. To simplify mbigen driver,I used a new conception--mbigen device. Each mbigen device is initialized as a platform device. Mbigen device presents the parts(register, pin definition etc.) in mbigen chip corresponding to a peripheral device. So from software view, the structure likes below mbigen chip |---------------------|-----------------| mbigen device1 mbigen device2 mbigen device3 | | | dev1 dev2 dev3 Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Ma Jun <majun258@huawei.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-12-18irqchip/gic: Kconfig the number of instancesLinus Walleij1-0/+5
There is currently a hack in the GIC driver making it possible to pass the number of GIC instances from the platform-specific include files and thus override the variable MAX_GIC_NR. With multiplatform deployments, this will not work as we need to get rid of the platform-specific include files. It turns out that this feature is only used by the RealView platform which has a cascaded GIC. So move the configuration to Kconfig and bump to 2 instances if we're building for the RealView. The include file hacks can then be removed. Tested on the ARM PB11MPCore with its cascaded GIC. Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-19 03:35:28 +0000