| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
ROCE uses "VA % buf_page_size" to caclulate the offset in the PBL's first
page, the actual PA corresponding to the MR's VA is equal to MR's PA plus
this offset. The first PA in PBL has already been aligned to PAGE_SIZE
after calling ib_umem_get(), but the MR's VA may not. If the buf_page_size
is smaller than the PAGE_SIZE, this will lead the HW to access the wrong
memory because the offset is smaller than expected.
Fixes: 9b2cf76c9f05 ("RDMA/hns: Optimize PBL buffer allocation process")
Link: https://lore.kernel.org/r/1594726935-45666-1-git-send-email-liweihang@huawei.com
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
The RoCE Engine will schedule to another QP after one has sent
(2 ^ lp_pktn_ini) packets. lp_pktn_ini is set in QPC and should be
calculated from 2 factors:
1. current MTU as a integer
2. the RoCE Engine's maximum slice length 64KB
But the driver use MTU as a enum ib_mtu and the max inline capability, the
lp_pktn_ini will be much bigger than expected which may cause traffic of
some QPs to never get scheduled.
Fixes: b713128de7a1 ("RDMA/hns: Adjust lp_pktn_ini dynamically")
Link: https://lore.kernel.org/r/1594726138-49294-1-git-send-email-liweihang@huawei.com
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
SRQ table is accessed both from interrupt and process context,
therefore we must use xa_lock_irq.
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
kworker/u17:9/8573 takes:
ffff8883e3503d30 (&xa->xa_lock#13){?...}-{2:2}, at: mlx5_cmd_get_srq+0x18/0x70 [mlx5_ib]
{IN-HARDIRQ-W} state was registered at:
lock_acquire+0xb9/0x3a0
_raw_spin_lock+0x25/0x30
srq_event_notifier+0x2b/0xc0 [mlx5_ib]
notifier_call_chain+0x45/0x70
__atomic_notifier_call_chain+0x69/0x100
forward_event+0x36/0xc0 [mlx5_core]
notifier_call_chain+0x45/0x70
__atomic_notifier_call_chain+0x69/0x100
mlx5_eq_async_int+0xc5/0x160 [mlx5_core]
notifier_call_chain+0x45/0x70
__atomic_notifier_call_chain+0x69/0x100
mlx5_irq_int_handler+0x19/0x30 [mlx5_core]
__handle_irq_event_percpu+0x43/0x2a0
handle_irq_event_percpu+0x30/0x70
handle_irq_event+0x34/0x60
handle_edge_irq+0x7c/0x1b0
do_IRQ+0x60/0x110
ret_from_intr+0x0/0x2a
default_idle+0x34/0x160
do_idle+0x1ec/0x220
cpu_startup_entry+0x19/0x20
start_secondary+0x153/0x1a0
secondary_startup_64+0xa4/0xb0
irq event stamp: 20907
hardirqs last enabled at (20907): _raw_spin_unlock_irq+0x24/0x30
hardirqs last disabled at (20906): _raw_spin_lock_irq+0xf/0x40
softirqs last enabled at (20746): __do_softirq+0x2c9/0x436
softirqs last disabled at (20681): irq_exit+0xb3/0xc0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&xa->xa_lock#13);
<Interrupt>
lock(&xa->xa_lock#13);
*** DEADLOCK ***
2 locks held by kworker/u17:9/8573:
#0: ffff888295218d38 ((wq_completion)mlx5_ib_page_fault){+.+.}-{0:0}, at: process_one_work+0x1f1/0x5f0
#1: ffff888401647e78 ((work_completion)(&pfault->work)){+.+.}-{0:0}, at: process_one_work+0x1f1/0x5f0
stack backtrace:
CPU: 0 PID: 8573 Comm: kworker/u17:9 Tainted: GO 5.7.0_for_upstream_min_debug_2020_06_14_11_31_46_41 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5_ib_page_fault mlx5_ib_eqe_pf_action [mlx5_ib]
Call Trace:
dump_stack+0x71/0x9b
mark_lock+0x4f2/0x590
? print_shortest_lock_dependencies+0x200/0x200
__lock_acquire+0xa00/0x1eb0
lock_acquire+0xb9/0x3a0
? mlx5_cmd_get_srq+0x18/0x70 [mlx5_ib]
_raw_spin_lock+0x25/0x30
? mlx5_cmd_get_srq+0x18/0x70 [mlx5_ib]
mlx5_cmd_get_srq+0x18/0x70 [mlx5_ib]
mlx5_ib_eqe_pf_action+0x257/0xa30 [mlx5_ib]
? process_one_work+0x209/0x5f0
process_one_work+0x27b/0x5f0
? __schedule+0x280/0x7e0
worker_thread+0x2d/0x3c0
? process_one_work+0x5f0/0x5f0
kthread+0x111/0x130
? kthread_park+0x90/0x90
ret_from_fork+0x24/0x30
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Link: https://lore.kernel.org/r/20200712102641.15210-1-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
ib_pd is accessed internally during destroy of the TIR/TIS, but PD
can be not set yet. This leading to the following kernel panic.
BUG: kernel NULL pointer dereference, address: 0000000000000074
PGD 8000000079eaa067 P4D 8000000079eaa067 PUD 7ae81067 PMD 0 Oops: 0000 [#1] SMP PTI
CPU: 1 PID: 709 Comm: syz-executor.0 Not tainted 5.8.0-rc3 #41 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
RIP: 0010:destroy_raw_packet_qp_tis drivers/infiniband/hw/mlx5/qp.c:1189 [inline]
RIP: 0010:destroy_raw_packet_qp drivers/infiniband/hw/mlx5/qp.c:1527 [inline]
RIP: 0010:destroy_qp_common+0x2ca/0x4f0 drivers/infiniband/hw/mlx5/qp.c:2397
Code: 00 85 c0 74 2e e8 56 18 55 ff 48 8d b3 28 01 00 00 48 89 ef e8 d7 d3 ff ff 48 8b 43 08 8b b3 c0 01 00 00 48 8b bd a8 0a 00 00 <0f> b7 50 74 e8 0d 6a fe ff e8 28 18 55 ff 49 8d 55 50 4c 89 f1 48
RSP: 0018:ffffc900007bbac8 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff88807949e800 RCX: 0000000000000998
RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffff88807c180140
RBP: ffff88807b50c000 R08: 000000000002d379 R09: ffffc900007bba00
R10: 0000000000000001 R11: 000000000002d358 R12: ffff888076f37000
R13: ffff88807949e9c8 R14: ffffc900007bbe08 R15: ffff888076f37000
FS: 00000000019bf940(0000) GS:ffff88807dd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000074 CR3: 0000000076d68004 CR4: 0000000000360ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
mlx5_ib_create_qp+0xf36/0xf90 drivers/infiniband/hw/mlx5/qp.c:3014
_ib_create_qp drivers/infiniband/core/core_priv.h:333 [inline]
create_qp+0x57f/0xd20 drivers/infiniband/core/uverbs_cmd.c:1443
ib_uverbs_create_qp+0xcf/0x100 drivers/infiniband/core/uverbs_cmd.c:1564
ib_uverbs_write+0x5fa/0x780 drivers/infiniband/core/uverbs_main.c:664
__vfs_write+0x3f/0x90 fs/read_write.c:495
vfs_write+0xc7/0x1f0 fs/read_write.c:559
ksys_write+0x5e/0x110 fs/read_write.c:612
do_syscall_64+0x3e/0x70 arch/x86/entry/common.c:359
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x466479
Code: Bad RIP value.
RSP: 002b:00007ffd057b62b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000466479
RDX: 0000000000000070 RSI: 0000000020000240 RDI: 0000000000000003
RBP: 00000000019bf8fc R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 0000000000000bf6 R14: 00000000004cb859 R15: 00000000006fefc0
Fixes: 6c41965d647a ("RDMA/mlx5: Don't access ib_qp fields in internal destroy QP path")
Link: https://lore.kernel.org/r/20200707110612.882962-4-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Some released FW versions mistakenly don't set the capability that 50G per
lane link-modes are supported for VFs (ptys_extended_ethernet capability
bit).
Use PTYS.ext_eth_proto_capability instead, as this indication is always
accurate. If PTYS.ext_eth_proto_capability is valid
(has a non-zero value) conclude that the HCA supports 50G per lane.
Otherwise, conclude that the HCA doesn't support 50G per lane.
Fixes: 08e8676f1607 ("IB/mlx5: Add support for 50Gbps per lane link modes")
Link: https://lore.kernel.org/r/20200707110612.882962-3-leon@kernel.org
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
The workqueue link_wq should only be destroyed when the hfi1 driver is
unloaded, not when the device is shut down.
Fixes: 71d47008ca1b ("IB/hfi1: Create workqueue for link events")
Link: https://lore.kernel.org/r/20200623204053.107638.70315.stgit@awfm-01.aw.intel.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
The workqueue hfi1_wq is destroyed in function shutdown_device(), which is
called by either shutdown_one() or remove_one(). The function
shutdown_one() is called when the kernel is rebooted while remove_one() is
called when the hfi1 driver is unloaded. When the kernel is rebooted,
hfi1_wq is destroyed while all qps are still active, leading to a kernel
crash:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000102
IP: [<ffffffff94cb7b02>] __queue_work+0x32/0x3e0
PGD 0
Oops: 0000 [#1] SMP
Modules linked in: dm_round_robin nvme_rdma(OE) nvme_fabrics(OE) nvme_core(OE) ib_isert iscsi_target_mod target_core_mod ib_ucm mlx4_ib iTCO_wdt iTCO_vendor_support mxm_wmi sb_edac intel_powerclamp coretemp intel_rapl iosf_mbi kvm rpcrdma sunrpc irqbypass crc32_pclmul ghash_clmulni_intel rdma_ucm aesni_intel ib_uverbs lrw gf128mul opa_vnic glue_helper ablk_helper ib_iser cryptd ib_umad rdma_cm iw_cm ses enclosure libiscsi scsi_transport_sas pcspkr joydev ib_ipoib(OE) scsi_transport_iscsi ib_cm sg ipmi_ssif mei_me lpc_ich i2c_i801 mei ioatdma ipmi_si dm_multipath ipmi_devintf ipmi_msghandler wmi acpi_pad acpi_power_meter hangcheck_timer ip_tables ext4 mbcache jbd2 mlx4_en sd_mod crc_t10dif crct10dif_generic mgag200 drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm hfi1(OE)
crct10dif_pclmul crct10dif_common crc32c_intel drm ahci mlx4_core libahci rdmavt(OE) igb megaraid_sas ib_core libata drm_panel_orientation_quirks ptp pps_core devlink dca i2c_algo_bit dm_mirror dm_region_hash dm_log dm_mod
CPU: 19 PID: 0 Comm: swapper/19 Kdump: loaded Tainted: G OE ------------ 3.10.0-957.el7.x86_64 #1
Hardware name: Phegda X2226A/S2600CW, BIOS SE5C610.86B.01.01.0024.021320181901 02/13/2018
task: ffff8a799ba0d140 ti: ffff8a799bad8000 task.ti: ffff8a799bad8000
RIP: 0010:[<ffffffff94cb7b02>] [<ffffffff94cb7b02>] __queue_work+0x32/0x3e0
RSP: 0018:ffff8a90dde43d80 EFLAGS: 00010046
RAX: 0000000000000082 RBX: 0000000000000086 RCX: 0000000000000000
RDX: ffff8a90b924fcb8 RSI: 0000000000000000 RDI: 000000000000001b
RBP: ffff8a90dde43db8 R08: ffff8a799ba0d6d8 R09: ffff8a90dde53900
R10: 0000000000000002 R11: ffff8a90dde43de8 R12: ffff8a90b924fcb8
R13: 000000000000001b R14: 0000000000000000 R15: ffff8a90d2890000
FS: 0000000000000000(0000) GS:ffff8a90dde40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000102 CR3: 0000001a70410000 CR4: 00000000001607e0
Call Trace:
[<ffffffff94cb8105>] queue_work_on+0x45/0x50
[<ffffffffc03f781e>] _hfi1_schedule_send+0x6e/0xc0 [hfi1]
[<ffffffffc03f78a2>] hfi1_schedule_send+0x32/0x70 [hfi1]
[<ffffffffc02cf2d9>] rvt_rc_timeout+0xe9/0x130 [rdmavt]
[<ffffffff94ce563a>] ? trigger_load_balance+0x6a/0x280
[<ffffffffc02cf1f0>] ? rvt_free_qpn+0x40/0x40 [rdmavt]
[<ffffffff94ca7f58>] call_timer_fn+0x38/0x110
[<ffffffffc02cf1f0>] ? rvt_free_qpn+0x40/0x40 [rdmavt]
[<ffffffff94caa3bd>] run_timer_softirq+0x24d/0x300
[<ffffffff94ca0f05>] __do_softirq+0xf5/0x280
[<ffffffff9537832c>] call_softirq+0x1c/0x30
[<ffffffff94c2e675>] do_softirq+0x65/0xa0
[<ffffffff94ca1285>] irq_exit+0x105/0x110
[<ffffffff953796c8>] smp_apic_timer_interrupt+0x48/0x60
[<ffffffff95375df2>] apic_timer_interrupt+0x162/0x170
<EOI>
[<ffffffff951adfb7>] ? cpuidle_enter_state+0x57/0xd0
[<ffffffff951ae10e>] cpuidle_idle_call+0xde/0x230
[<ffffffff94c366de>] arch_cpu_idle+0xe/0xc0
[<ffffffff94cfc3ba>] cpu_startup_entry+0x14a/0x1e0
[<ffffffff94c57db7>] start_secondary+0x1f7/0x270
[<ffffffff94c000d5>] start_cpu+0x5/0x14
The solution is to destroy the workqueue only when the hfi1 driver is
unloaded, not when the device is shut down. In addition, when the device
is shut down, no more work should be scheduled on the workqueues and the
workqueues are flushed.
Fixes: 8d3e71136a08 ("IB/{hfi1, qib}: Add handling of kernel restart")
Link: https://lore.kernel.org/r/20200623204047.107638.77646.stgit@awfm-01.aw.intel.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Legacy IPoIB sets IB_QP_CREATE_NETIF_QP QP create flag and because mlx5
doesn't use this flag, the process_create_flags() failed to create IPoIB
QPs.
Fixes: 2978975ce7f1 ("RDMA/mlx5: Process create QP flags in one place")
Link: https://lore.kernel.org/r/20200630122147.445847-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Clang warns:
drivers/infiniband/hw/hfi1/qp.c:198:9: warning: implicit conversion from enumeration type 'enum opa_mtu' to different enumeration type 'enum ib_mtu' [-Wenum-conversion]
mtu = OPA_MTU_8192;
~ ^~~~~~~~~~~~
enum opa_mtu extends enum ib_mtu. There are typically two ways to deal
with this:
* Remove the expected types and just use 'int' for all parameters and
types.
* Explicitly cast the enums between each other.
This driver chooses to do the later so do the same thing here.
Fixes: 6d72344cf6c4 ("IB/ipoib: Increase ipoib Datagram mode MTU's upper limit")
Link: https://lore.kernel.org/r/20200623005224.492239-1-natechancellor@gmail.com
Link: https://github.com/ClangBuiltLinux/linux/issues/1062
Link: https://lore.kernel.org/linux-rdma/20200527040350.GA3118979@ubuntu-s3-xlarge-x86/
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
When running iperf in a two host configuration the following trace can
occur:
[ 319.728730] NETDEV WATCHDOG: ib0 (hfi1): transmit queue 0 timed out
The issue happens because the current implementation relies on the netif
txq being stopped to control the flushing of the tx list.
There are two resources that the transmit logic can wait on and stop the
txq:
- SDMA descriptors
- Ring space to hold completions
The ring space is tested on the sending side and relieved when the ring is
consumed in the napi tx reaping.
Unfortunately, that reaping can run conncurrently with the workqueue
flushing of the txlist. If the txq is started just before the workitem
executes, the txlist will never be flushed, leading to the txq being
stuck.
Fix by:
- Adding sleep/wakeup wrappers
* Use an atomic to control the call to the netif routines inside the
wrappers
- Use another atomic to record ring space exhaustion
* Only wakeup when the a ring space exhaustion has happened and it
relieved
Add additional wrappers to clarify the ring space resource handling.
Fixes: d99dc602e2a5 ("IB/hfi1: Add functions to transmit datagram ipoib packets")
Link: https://lore.kernel.org/r/20200623204327.108092.4024.stgit@awfm-01.aw.intel.com
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
The current code mishandles -EBUSY in two ways:
- The flow change doesn't test the return from the flush and runs on to
process the current packet racing with the wakeup processing
- The -EBUSY handling for a single packet inserts the tx into the txlist
after the submit call, racing with the same wakeup processing
Fix the first by dropping the skb and returning NETDEV_TX_OK.
Fix the second by insuring the the list entry within the txreq is inited
when allocated. This enables the sleep routine to detect that the txreq
has used the non-list api and queue the packet to the txlist.
Both flaws can lead to having the flushing thread executing in causing two
threads to manipulate the txlist.
Fixes: d99dc602e2a5 ("IB/hfi1: Add functions to transmit datagram ipoib packets")
Link: https://lore.kernel.org/r/20200623204321.108092.83898.stgit@awfm-01.aw.intel.com
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
When the try_module_get calls were removed from opening and closing of the
i2c debugfs file, the corresponding module_put calls were missed. This
results in an inaccurate module use count that requires a power cycle to
fix.
Fixes: 09fbca8e6240 ("IB/hfi1: No need to use try_module_get for debugfs")
Link: https://lore.kernel.org/r/20200623203230.106975.76240.stgit@awfm-01.aw.intel.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
We need to do some rework on the dummy netdev. Calling the free_netdev()
would normally make sense, and that will be addressed in an upcoming
patch. For now just revert the behavior to what it was before keeping the
unused variable removal part of the patch.
The dd->dumm_netdev is mainly used for packet receiving through
alloc_netdev_mqs() for typical net devices. A a result, it should be freed
with kfree instead of free_netdev() that leads to a crash when unloading
the hfi1 module:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 8000000855b54067 P4D 8000000855b54067 PUD 84a4f5067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 73 PID: 10299 Comm: modprobe Not tainted 5.6.0-rc5+ #1
Hardware name: Intel Corporation S2600WT2R/S2600WT2R, BIOS SE5C610.86B.01.01.0016.033120161139 03/31/2016
RIP: 0010:__hw_addr_flush+0x12/0x80
Code: 40 00 48 83 c4 08 4c 89 e7 5b 5d 41 5c e9 76 77 18 00 66 0f 1f 44 00 00 0f 1f 44 00 00 41 54 49 89 fc 55 53 48 8b 1f 48 39 df <48> 8b 2b 75 08 eb 4a 48 89 eb 48 89 c5 48 89 df e8 99 bf d0 ff 84
RSP: 0018:ffffb40e08783db8 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000002
RDX: ffffb40e00000000 RSI: 0000000000000246 RDI: ffff88ab13662298
RBP: ffff88ab13662000 R08: 0000000000001549 R09: 0000000000001549
R10: 0000000000000001 R11: 0000000000aaaaaa R12: ffff88ab13662298
R13: ffff88ab1b259e20 R14: ffff88ab1b259e42 R15: 0000000000000000
FS: 00007fb39b534740(0000) GS:ffff88b31f940000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000084d3ea004 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
dev_addr_flush+0x15/0x30
free_netdev+0x7e/0x130
hfi1_netdev_free+0x59/0x70 [hfi1]
remove_one+0x65/0x110 [hfi1]
pci_device_remove+0x3b/0xc0
device_release_driver_internal+0xec/0x1b0
driver_detach+0x46/0x90
bus_remove_driver+0x58/0xd0
pci_unregister_driver+0x26/0xa0
hfi1_mod_cleanup+0xc/0xd54 [hfi1]
__x64_sys_delete_module+0x16c/0x260
? exit_to_usermode_loop+0xa4/0xc0
do_syscall_64+0x5b/0x200
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 193ba03141bb ("IB/hfi1: Use free_netdev() in hfi1_netdev_free()")
Link: https://lore.kernel.org/r/20200623203224.106975.16926.stgit@awfm-01.aw.intel.com
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Don't deref udata if it is NULL
BUG: kernel NULL pointer dereference, address: 0000000000000030
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 SMP PTI
CPU: 2 PID: 1592 Comm: python3 Not tainted 5.7.0-rc6+ #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
RIP: 0010:create_qp+0x39e/0xae0 [mlx5_ib]
Code: c0 0d 00 00 bf 10 01 00 00 e8 be a9 e4 e0 48 85 c0 49 89 c2 0f 84 0c 07 00 00 41 8b 85 74 63 01 00 0f c8 a9 00 00 00 10 74 0a <41> 8b 46 30 0f c8 41 89 42 14 41 8b 52 18 41 0f b6 4a 1c 0f ca 89
RSP: 0018:ffffc9000067f8b0 EFLAGS: 00010206
RAX: 0000000010170000 RBX: ffff888441313000 RCX: 0000000000000000
RDX: 0000000000000200 RSI: 0000000000000000 RDI: ffff88845b1d4400
RBP: ffffc9000067fa60 R08: 0000000000000200 R09: ffff88845b1d4200
R10: ffff88845b1d4200 R11: ffff888441313000 R12: ffffc9000067f950
R13: ffff88846ac00140 R14: 0000000000000000 R15: ffff88846c2bc000
FS: 00007faa1a3c0540(0000) GS:ffff88846fd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000030 CR3: 0000000446dca003 CR4: 0000000000760ea0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
? __switch_to_asm+0x40/0x70
? __switch_to_asm+0x34/0x70
mlx5_ib_create_qp+0x897/0xfa0 [mlx5_ib]
ib_create_qp+0x9e/0x300 [ib_core]
create_qp+0x92d/0xb20 [ib_uverbs]
? ib_uverbs_cq_event_handler+0x30/0x30 [ib_uverbs]
? release_resource+0x30/0x30
ib_uverbs_create_qp+0xc4/0xe0 [ib_uverbs]
ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0xc8/0xf0 [ib_uverbs]
ib_uverbs_run_method+0x223/0x770 [ib_uverbs]
? track_pfn_remap+0xa7/0x100
? uverbs_disassociate_api+0xd0/0xd0 [ib_uverbs]
? remap_pfn_range+0x358/0x490
ib_uverbs_cmd_verbs.isra.6+0x19b/0x370 [ib_uverbs]
? rdma_umap_priv_init+0x82/0xe0 [ib_core]
? vm_mmap_pgoff+0xec/0x120
ib_uverbs_ioctl+0xc0/0x120 [ib_uverbs]
ksys_ioctl+0x92/0xb0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x48/0x130
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: e383085c2425 ("RDMA/mlx5: Set ECE options during QP create")
Link: https://lore.kernel.org/r/20200621115959.60126-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
create_flags checks was refactored and broke the creation on integrity
enabled QPs and actually broke the NVMe/RDMA and iSER ULP's when using
mlx5 driven devices.
Fixes: 2978975ce7f1 ("RDMA/mlx5: Process create QP flags in one place")
Link: https://lore.kernel.org/r/20200617130230.2846915-1-leon@kernel.org
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Like any other QP type, rely on FW for the RAW_PACKET QPs to decide if ECE
is supported or not. This fixes an inability to create RAW_PACKET QPs with
latest rdma-core with the ECE support.
Fixes: e383085c2425 ("RDMA/mlx5: Set ECE options during QP create")
Link: https://lore.kernel.org/r/20200618112507.3453496-2-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Remote gid is not copied to the right address. Fix it by using
rdma_ah_set_dgid_raw to copy the remote gid value from the QP context on
query QP.
Fixes: 70bd7fb87625 ("RDMA/mlx5: Remove manually crafted QP context the query call")
Link: https://lore.kernel.org/r/20200618112507.3453496-3-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
destroy_qp_common is called for flows where QP is already created by
HW. While it is called from IB/core, the ibqp.* fields will be fully
initialized, but it is not the case if this function is called during QP
creation.
Don't rely on ibqp fields as much as possible and initialize
send_cq/recv_cq as temporal solution till all drivers will be converted to
IB/core QP allocation scheme.
refcount_t: underflow; use-after-free.
WARNING: CPU: 1 PID: 5372 at lib/refcount.c:28 refcount_warn_saturate+0xfe/0x1a0
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 5372 Comm: syz-executor.2 Not tainted 5.5.0-rc5 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
mlx5_core_put_rsc+0x70/0x80
destroy_resource_common+0x8e/0xb0
mlx5_core_destroy_qp+0xaf/0x1d0
mlx5_ib_destroy_qp+0xeb0/0x1460
ib_destroy_qp_user+0x2d5/0x7d0
create_qp+0xed3/0x2130
ib_uverbs_create_qp+0x13e/0x190
? ib_uverbs_ex_create_qp
ib_uverbs_write+0xaa5/0xdf0
__vfs_write+0x7c/0x100
ksys_write+0xc8/0x200
do_syscall_64+0x9c/0x390
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 08d53976609a ("RDMA/mlx5: Copy response to the user in one place")
Link: https://lore.kernel.org/r/20200617130148.2846643-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
If a IMP reset caused by some hardware errors and hns RoCE driver reset
occurred at the same time, there is a possiblity that the IMP will stop
dealing with command and users can't use the hardware. The logs are as
follows:
hns3 0000:fd:00.1: cleaned 0, need to clean 1
hns3 0000:fd:00.1: firmware version query failed -11
hns3 0000:fd:00.1: Cmd queue init failed
hns3 0000:fd:00.1: Upgrade reset level
hns3 0000:fd:00.1: global reset interrupt
The hns NIC driver divides the reset process into 3 status:
initialization, hardware resetting and softwaring restting. RoCE driver
gets reset status by interfaces provided by NIC driver and commands will
not be sent to the IMP if the driver is in any above status. The main
reason for this issue is that there is a time gap between status 1 and 2,
if the RoCE driver sends commands to the IMP during this gap, the IMP will
stop working because it is not ready.
To eliminate the time gap, the hns NIC driver has added a new interface in
commit a4de02287abb9 ("net: hns3: provide .get_cmdq_stat interface for the
client"), so RoCE driver can ensure that no commands will be sent during
resetting.
Link: https://lore.kernel.org/r/1592314778-52822-1-git-send-email-liweihang@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
ibmr.device is assigned after MR is successfully registered, but both
write_mtpt() and frmr_write_mtpt() accesses it during the mr registration
process, which may cause the following error when trying to register MR in
userspace and pbl_hop_num is set to 0.
pc : hns_roce_mtr_find+0xa0/0x200 [hns_roce]
lr : set_mtpt_pbl+0x54/0x118 [hns_roce_hw_v2]
sp : ffff00023e73ba20
x29: ffff00023e73ba20 x28: ffff00023e73bad8
x27: 0000000000000000 x26: 0000000000000000
x25: 0000000000000002 x24: 0000000000000000
x23: ffff00023e73bad0 x22: 0000000000000000
x21: ffff0000094d9000 x20: 0000000000000000
x19: ffff8020a6bdb2c0 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0140000000000000 x12: 0040000000000041
x11: ffff000240000000 x10: 0000000000001000
x9 : 0000000000000000 x8 : ffff802fb7558480
x7 : ffff802fb7558480 x6 : 000000000003483d
x5 : ffff00023e73bad0 x4 : 0000000000000002
x3 : ffff00023e73bad8 x2 : 0000000000000000
x1 : 0000000000000000 x0 : ffff0000094d9708
Call trace:
hns_roce_mtr_find+0xa0/0x200 [hns_roce]
set_mtpt_pbl+0x54/0x118 [hns_roce_hw_v2]
hns_roce_v2_write_mtpt+0x14c/0x168 [hns_roce_hw_v2]
hns_roce_mr_enable+0x6c/0x148 [hns_roce]
hns_roce_reg_user_mr+0xd8/0x130 [hns_roce]
ib_uverbs_reg_mr+0x14c/0x2e0 [ib_uverbs]
ib_uverbs_write+0x27c/0x3e8 [ib_uverbs]
__vfs_write+0x60/0x190
vfs_write+0xac/0x1c0
ksys_write+0x6c/0xd8
__arm64_sys_write+0x24/0x30
el0_svc_common+0x78/0x130
el0_svc_handler+0x38/0x78
el0_svc+0x8/0xc
Solve above issue by adding a pointer of structure hns_roce_dev as a
parameter of write_mtpt() and frmr_write_mtpt(), so that both of these
functions can access it before finishing MR's registration.
Fixes: 9b2cf76c9f05 ("RDMA/hns: Optimize PBL buffer allocation process")
Link: https://lore.kernel.org/r/1592314629-51715-1-git-send-email-liweihang@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Missed steps during ECE handshake left userspace application with less
options for the ECE handshake. Pass ECE options in the additional
transitions.
Fixes: 50aec2c3135e ("RDMA/mlx5: Return ECE data after modify QP")
Link: https://lore.kernel.org/r/20200616104536.2426384-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Private data passed to iwarp_cm_handler is copied for connection request /
response, but ignored otherwise. If junk is passed, it is stored in the
event and used later in the event processing.
The driver passes an old junk pointer during connection close which leads
to a use-after-free on event processing. Set private data to NULL for
events that don 't have private data.
BUG: KASAN: use-after-free in ucma_event_handler+0x532/0x560 [rdma_ucm]
kernel: Read of size 4 at addr ffff8886caa71200 by task kworker/u128:1/5250
kernel:
kernel: Workqueue: iw_cm_wq cm_work_handler [iw_cm]
kernel: Call Trace:
kernel: dump_stack+0x8c/0xc0
kernel: print_address_description.constprop.0+0x1b/0x210
kernel: ? ucma_event_handler+0x532/0x560 [rdma_ucm]
kernel: ? ucma_event_handler+0x532/0x560 [rdma_ucm]
kernel: __kasan_report.cold+0x1a/0x33
kernel: ? ucma_event_handler+0x532/0x560 [rdma_ucm]
kernel: kasan_report+0xe/0x20
kernel: check_memory_region+0x130/0x1a0
kernel: memcpy+0x20/0x50
kernel: ucma_event_handler+0x532/0x560 [rdma_ucm]
kernel: ? __rpc_execute+0x608/0x620 [sunrpc]
kernel: cma_iw_handler+0x212/0x330 [rdma_cm]
kernel: ? iw_conn_req_handler+0x6e0/0x6e0 [rdma_cm]
kernel: ? enqueue_timer+0x86/0x140
kernel: ? _raw_write_lock_irq+0xd0/0xd0
kernel: cm_work_handler+0xd3d/0x1070 [iw_cm]
Fixes: e411e0587e0d ("RDMA/qedr: Add iWARP connection management functions")
Link: https://lore.kernel.org/r/20200616093408.17827-1-michal.kalderon@marvell.com
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The max_pkeys device attribute was not set in query device verb, set it to
one in order to account for the default pkey (0xffff). This information is
exposed to userspace and can cause malfunction
Fixes: 40909f664d27 ("RDMA/efa: Add EFA verbs implementation")
Link: https://lore.kernel.org/r/20200614103534.88060-1-galpress@amazon.com
Reviewed-by: Firas JahJah <firasj@amazon.com>
Reviewed-by: Yossi Leybovich <sleybo@amazon.com>
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The word 'descriptor' is misspelled throughout the tree.
Fix it up accordingly:
decriptors -> descriptors
Link: https://lore.kernel.org/r/20200609124610.3445662-3-kieran.bingham+renesas@ideasonboard.com
Link: https://lore.kernel.org/r/20200609124610.3445662-12-kieran.bingham+renesas@ideasonboard.com
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Variables of type size_t should use %zu rather than %lu [1]. The variables
"inlen", "ucmd", "last", and "size" are all size_t, so use the correct
format specifiers.
[1] https://www.kernel.org/doc/html/latest/core-api/printk-formats.html
Fixes: e383085c2425 ("RDMA/mlx5: Set ECE options during QP create")
Link: https://lore.kernel.org/r/20200605023012.9527-1-tseewald@gmail.com
Signed-off-by: Tom Seewald <tseewald@gmail.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The assignment to resp.response_length is never read since it is being
updated again on the next statement. The assignment is redundant so
removed it.
Fixes: a645a89d9a78 ("RDMA/mlx5: Return ECE DC support")
Link: https://lore.kernel.org/r/20200604143902.56021-1-colin.king@canonical.com
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Convert comments that reference mmap_sem to reference mmap_lock instead.
[akpm@linux-foundation.org: fix up linux-next leftovers]
[akpm@linux-foundation.org: s/lockaphore/lock/, per Vlastimil]
[akpm@linux-foundation.org: more linux-next fixups, per Michel]
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Liam Howlett <Liam.Howlett@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ying Han <yinghan@google.com>
Link: http://lkml.kernel.org/r/20200520052908.204642-13-walken@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This change converts the existing mmap_sem rwsem calls to use the new mmap
locking API instead.
The change is generated using coccinelle with the following rule:
// spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir .
@@
expression mm;
@@
(
-init_rwsem
+mmap_init_lock
|
-down_write
+mmap_write_lock
|
-down_write_killable
+mmap_write_lock_killable
|
-down_write_trylock
+mmap_write_trylock
|
-up_write
+mmap_write_unlock
|
-downgrade_write
+mmap_write_downgrade
|
-down_read
+mmap_read_lock
|
-down_read_killable
+mmap_read_lock_killable
|
-down_read_trylock
+mmap_read_trylock
|
-up_read
+mmap_read_unlock
)
-(&mm->mmap_sem)
+(mm)
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Liam Howlett <Liam.Howlett@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ying Han <yinghan@google.com>
Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The replacement of <asm/pgrable.h> with <linux/pgtable.h> made the include
of the latter in the middle of asm includes. Fix this up with the aid of
the below script and manual adjustments here and there.
import sys
import re
if len(sys.argv) is not 3:
print "USAGE: %s <file> <header>" % (sys.argv[0])
sys.exit(1)
hdr_to_move="#include <linux/%s>" % sys.argv[2]
moved = False
in_hdrs = False
with open(sys.argv[1], "r") as f:
lines = f.readlines()
for _line in lines:
line = _line.rstrip('
')
if line == hdr_to_move:
continue
if line.startswith("#include <linux/"):
in_hdrs = True
elif not moved and in_hdrs:
moved = True
print hdr_to_move
print line
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull rdma updates from Jason Gunthorpe:
"A more active cycle than most of the recent past, with a few large,
long discussed works this time.
The RNBD block driver has been posted for nearly two years now, and
flowing through RDMA due to it also introducing a new ULP.
The removal of FMR has been a recurring discussion theme for a long
time.
And the usual smattering of features and bug fixes.
Summary:
- Various small driver bugs fixes in rxe, mlx5, hfi1, and efa
- Continuing driver cleanups in bnxt_re, hns
- Big cleanup of mlx5 QP creation flows
- More consistent use of src port and flow label when LAG is used and
a mlx5 implementation
- Additional set of cleanups for IB CM
- 'RNBD' network block driver and target. This is a network block
RDMA device specific to ionos's cloud environment. It brings strong
multipath and resiliency capabilities.
- Accelerated IPoIB for HFI1
- QP/WQ/SRQ ioctl migration for uverbs, and support for multiple
async fds
- Support for exchanging the new IBTA defiend ECE data during RDMA CM
exchanges
- Removal of the very old and insecure FMR interface from all ULPs
and drivers. FRWR should be preferred for at least a decade now"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (247 commits)
RDMA/cm: Spurious WARNING triggered in cm_destroy_id()
RDMA/mlx5: Return ECE DC support
RDMA/mlx5: Don't rely on FW to set zeros in ECE response
RDMA/mlx5: Return an error if copy_to_user fails
IB/hfi1: Use free_netdev() in hfi1_netdev_free()
RDMA/hns: Uninitialized variable in modify_qp_init_to_rtr()
RDMA/core: Move and rename trace_cm_id_create()
IB/hfi1: Fix hfi1_netdev_rx_init() error handling
RDMA: Remove 'max_map_per_fmr'
RDMA: Remove 'max_fmr'
RDMA/core: Remove FMR device ops
RDMA/rdmavt: Remove FMR memory registration
RDMA/mthca: Remove FMR support for memory registration
RDMA/mlx4: Remove FMR support for memory registration
RDMA/i40iw: Remove FMR leftovers
RDMA/bnxt_re: Remove FMR leftovers
RDMA/mlx5: Remove FMR leftovers
RDMA/core: Remove FMR pool API
RDMA/rds: Remove FMR support for memory registration
RDMA/srp: Remove support for FMR memory registration
...
|
|
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
|
|
The DC QPs are many-to-one QP types that means that first connection will
establish ECE options that coming connections should follow. Due to this
property, the ECE code was removed between first [1] and second [2] ECE
submissions.
This patch returns the dropped code, because ECE is a property of a
connection and like any other connection users are needed to manage this
data. Allow them to set ECE parameter for DC too and avoid need of having
compatibility flag for the DC ECE.
[1]
https://lore.kernel.org/linux-rdma/20200523132243.817936-1-leon@kernel.org/
[2]
https://lore.kernel.org/linux-rdma/20200525174401.71152-1-leon@kernel.org/
Link: https://lore.kernel.org/r/20200602125548.172654-4-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The FW returns zeros in case feature is not enabled, but it is better to
have the capability check and ensure that returned result is cleared.
Fixes: 3e09a427ae7a ("RDMA/mlx5: Get ECE options from FW during create QP")
Link: https://lore.kernel.org/r/20200602125548.172654-3-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
In theoretical event, the ib_copy_to_udata() can fail, so return -EFAULT
error to the user, so he will destroy the QP.
Fixes: 50aec2c3135e ("RDMA/mlx5: Return ECE data after modify QP")
Link: https://lore.kernel.org/r/20200602125548.172654-2-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
dummy_netdev shold be freed by free_netdev() instead of kfree(). Also
remove unneeded variable 'priv'
Fixes: 4730f4a6c6b2 ("IB/hfi1: Activate the dummy netdev")
Link: https://lore.kernel.org/r/20200602061635.31224-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The "dmac" variable is used before it is initialized.
Fixes: 494c3b312255 ("RDMA/hns: Refactor the QP context filling process related to WQE buffer configure")
Link: https://lore.kernel.org/r/20200529083918.GA1298465@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The hfi1_vnic_up() function doesn't check whether hfi1_netdev_rx_init()
returns errors. In hfi1_vnic_init() we need to change the code to
preserve the error code instead of returning success.
Fixes: 2280740f01ae ("IB/hfi1: Virtual Network Interface Controller (VNIC) HW support")
Fixes: 4730f4a6c6b2 ("IB/hfi1: Activate the dummy netdev")
Link: https://lore.kernel.org/r/20200530140224.GA1330098@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Now that FMR support is gone, this attribute can be deleted from all
places.
Link: https://lore.kernel.org/r/13-v3-f58e6669d5d3+2cf-fmr_removal_jgg@mellanox.com
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Now that FMR support is gone, this attribute can be deleted from all
places.
Link: https://lore.kernel.org/r/12-v3-f58e6669d5d3+2cf-fmr_removal_jgg@mellanox.com
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Bernard Metzler <bmt@zurich.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Remove the ancient and unsafe FMR method.
Link: https://lore.kernel.org/r/9-v3-f58e6669d5d3+2cf-fmr_removal_jgg@mellanox.com
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
HCA's that are driven by mlx4 driver support FRWR method to register
memory. Remove the ancient and unsafe FMR method.
Link: https://lore.kernel.org/r/8-v3-f58e6669d5d3+2cf-fmr_removal_jgg@mellanox.com
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The ibfmr member is never referenced, remove it.
Link: https://lore.kernel.org/r/7-v3-f58e6669d5d3+2cf-fmr_removal_jgg@mellanox.com
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The bnxt_re_fmr struct is never referenced and the max_fmr items
in bnxt_qplib_dev_attr are never read.
Link: https://lore.kernel.org/r/6-v3-f58e6669d5d3+2cf-fmr_removal_jgg@mellanox.com
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Remove a few leftovers from FMR functionality which are no longer used.
Link: https://lore.kernel.org/r/5-v3-f58e6669d5d3+2cf-fmr_removal_jgg@mellanox.com
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uaccess/access_ok updates from Al Viro:
"Removals of trivially pointless access_ok() calls.
Note: the fiemap stuff was removed from the series, since they are
duplicates with part of ext4 series carried in Ted's tree"
* 'uaccess.access_ok' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vmci_host: get rid of pointless access_ok()
hfi1: get rid of pointless access_ok()
usb: get rid of pointless access_ok() calls
lpfc_debugfs: get rid of pointless access_ok()
efi_test: get rid of pointless access_ok()
drm_read(): get rid of pointless access_ok()
via-pmu: don't bother with access_ok()
drivers/crypto/ccp/sev-dev.c: get rid of pointless access_ok()
omapfb: get rid of pointless access_ok() calls
amifb: get rid of pointless access_ok() calls
drivers/fpga/dfl-afu-dma-region.c: get rid of pointless access_ok()
drivers/fpga/dfl-fme-pr.c: get rid of pointless access_ok()
cm4000_cs.c cmm_ioctl(): get rid of pointless access_ok()
nvram: drop useless access_ok()
n_hdlc_tty_read(): remove pointless access_ok()
tomoyo_write_control(): get rid of pointless access_ok()
btrfs_ioctl_send(): don't bother with access_ok()
fat_dir_ioctl(): hadn't needed that access_ok() for more than a decade...
dlmfs_file_write(): get rid of pointless access_ok()
|
|
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
net/mlx5: Add ability to read and write ECE options
net/mlx5: Add support for RDMA TX FT headers modifying
net/mlx5: Move iseg access helper routines close to mlx5_core driver
net/mlx5: Cleanup mlx5_ifc_fte_match_set_misc2_bits
net/mlx5: Add support in forward to namespace
{IB/net}/mlx5: Simplify don't trap code
net/mlx5: Replace zero-length array with flexible-array
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There is a spelling mistake in an error message. Fix it.
Link: https://lore.kernel.org/r/20200528110709.400935-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
