| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
for-linus
Sagi writes:
Here we have:
- Kconfig dependencies fix from Arnd
- nvme-rdma device removal fixes from Steve
- possible bad deref fix from Colin
|
|
Otherwise an endpoint can be still closing down causing a touch
after free crash. Also WARN_ON if ulps have failed to destroy
various resources during device removal.
Fixes: ad61a4c7a9b7 ("iw_cxgb4: don't block in destroy_qp awaiting the last deref")
Reviewed-by: Sagi Grimberg <sagi@grimbrg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Reviewed-by: Sagi Grimberg <sagi@grimbrg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
The i40iw initiator sends an MPA-request with ird=16 and ord=16. The cxgb4
responder sends an MPA-reply with ord = 32 causing i40iw to terminate
due to insufficient resources.
The logic to reduce the ORD to <= peer's IRD was wrong.
Reported-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The i40iw initiator sends an MPA-request with ird = 63, ord = 63. The
cxgb4 responder sends a RST. Since the inbound ord=63 and it exceeds
the max_ird/c4iw_max_read_depth (=32 default), chelsio decides to abort.
Instead, cxgb4 should adjust the ord/ird down before presenting it to
the ULP.
Reported-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There exists a race where the application can setup a connection
and then disconnect it before iw_cxgb4 processes the fw4_ack
message. For passive side connections, the fw4_ack message is
used to know when to stop the ep timer for MPA_REPLY messages.
If the application disconnects before the fw4_ack is handled then
c4iw_ep_disconnect() needs to clean up the timer state and stop the
timer before restarting it for the disconnect timer. Failure to do this
results in a "timer already started" message and a premature stopping
of the disconnect timer.
Fixes: e4b76a2 ("RDMA/iw_cxgb4: stop_ep_timer() after MPA negotiation")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Pre-allocate buffers for sending various control messages to close
connection, abort connection, etc so that we gracefully handle
connections when system is running out of memory.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Get rid of unneeded code, and refactor things a bit.
For MPA version 0 we abort the connection. For > 0, we attempt to send
an MPA_START/REJECT Reply, and then disconnect gracefully. If the send
of the MPA message fails, then we abort the connection. We can ignore
c4iw_ep_disconnect() errors here because it will clean up the endpoint
if there are failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
markers_enabled should be read only once during MPA negotiation.
The present code does read markers_enabled twice during negotiation
which results in setting wrong recv/xmit markers if the markers_enabled is
changed in the middle of negotiation.
With this change the markers_enabled is read only once during MPA
negotiation. recv markers are set based on markers enabled module
parameter and xmit markers are set based on markers flag from the
MPA_START_REQ/MPA_START_REP.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
__force casts should be avoided if there is a better alternative.
Hence modify the comparison of s_addr with INADDR_ANY such that the
__force cast is no longer necessary.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Vipul Pandya <vipul@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
These handlers when called print error message to the kernel log,
but the actual handling is done by _c4iw_free_ep() and process_timeout().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Currently c4iw_peer_abort_intr() does not wake up the waiter if the
endpoint state indicates we're using MPAv2 and we're currently trying to
connect. This was introduced with commit 7c0a33d61187a ("RDMA/cxgb4:
Don't wakeup threads for MPAv2")
However, this original fix is flawed because it introduces a race that
can cause a deadlock of the iwarp stack. Here is the race:
->local side sets up an active offload connection.
->local side sends MPA_START request.
->peer sends MPA_START response.
->local side ingress cpl thread begins processing the MPA_START response,
but before it changes the state from MPA_REQ_SENT to FPDU_MODE:
->peer sends a RST which results in a ABORT_REQ_RSS. This triggers
peer_abort_intr() which sees the state in MPA_REQ_SENT and since mpa_rev
is 2, it will avoid waking up the endpoint with -ECONNRESET, assuming the
stack will re-attempt the connection using MPAv1.
->Meanwhile, the cpl thread moves the state to FPDU_MODE and calls
c4iw_modify_rc_qp() which calls rdma_init() which sends a RI_WR/INIT WR
to firmware. But since HW sent an abort, FW correctly drops the RI_WR/INIT
WR.
->So the cpl thread is stuck waiting for a reply and cannot process the
ABORT_REQ_RSS cpl sitting in its input queue. Thus everything comes to a
halt because no more ingress cpls are processed by the stack...
The correct fix for the issue is to always do the wake up in
c4iw_abort_intr() but reinitialize the wait object in c4iw_reconnect().
Fixes: 7c0a33d61187a ("RDMA/cxgb4: Don't wakeup threads for MPAv2")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add get_ep_from_stid() which will atomically find and reference the
endpoint struct if found. This avoids touch-after-free races between
threads destroying listening endpoints and the CPL processing thread
processing an incoming PASS_ACCEPT_REQ CPL.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
c4iw_reject() and c4iw_accept() need to handle the case where the
endpoint has timed out and is in the middle of ABORTING the connection.
Here is the flow that causes the BUG_ON() to fire on the server side:
1) offload connection setup and endpoint timer started
2) MPA_START request received from peer, CONNECT_REQUEST passed to ULP
3) endpoint timer fires, and process_timeout() aborts the connection,
this moves the endpoint state to ABORTING until HW sends up the
ABORT_RPL_RSS.
4) application exits closing the CONNECT_REQUEST cm_id. The IWCM calls
c4iw_reject_cr() to destroy this connection request.
5) WHAMO: BUG_ON() because the state is ABORTING.
The fix is to change c4iw_reject_cr() and c4iw_accept_cr() to fail the
operation if the state is not in MPA_REQ_RCVD vs in DEAD.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
ARP failure may also happen when ep in FPDU_MODE and these failures need
to be handled by process_timeout(). process_timeout() also has to handle
case MPA_REQ_RCVD, setting abort to 1, leading to ep resource release.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Arp failure for send_mpa_reply/reject() is handled by freeing the
mpa_skb in c4iw_free_ep() before releasing ep.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is a race between ULP threads calling c4iw_ep_disconnect() via
c4iw_modify_rc_qp() and the ingress CPL thread where the ULP thread
can free the endpoint just after the ingress CPL thread finds the ep
pointer in the tid table. To avoid this, we now use the hwtid_idr table
for lookups instead of the LLD tid table so we can lock around insert,
remove, and lookup+get_ep to avoid the race. The CPL handlers now will
either find the ep ptr and have a ref on it, or not find it and they
can discard the CPL. Callers of get_ep_from_tid() will have a ref
on the ep if found, and thus must deref when they are done.
Negative advice in peer_abort_intr() need to dereference the ep.
therefore peer_abort() is scheduled to dereference the ep later.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In abort_arp_failure(), the return value from c4iw_ofld_send() is
ignored and thus if the CPL isn't sent, the endpoint is stuck and never
gets aborted. Failure of c4iw_ofld_send() is treated as fatal error, and
the ep resources are released in a safer context through process_work().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Moving the state to ABORTING causes the ep to get stuck because
c4iw_ep_timeout() thinks the ABORT has already been done. So leave the
state alone and let c4iw_ep_disconnect() do the right thing given the
ep state.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
->In act_open_rpl(), CPL_ERR_TCAM_FULL error handling branch, there is
no handling of the return value of send_fw_act_open_req().
->In send_fw_act_open_req(), there is no handling of return value of
c4iw_l2t_send(), which may cause a ep leak and won't notify upper layers
on connection establish failure.
->send_mpa_req() should act on the return from c4iw_l2t_send() and
return the error to the caller.
->In case of c4iw_l2t_send() failure in send_mpa_req(), returns without
starting the timer and not changing the ep state, which is further
handled by act_establish()
-> In act_establish()?if send_mpa_request's get_skb returns an error,
may cause an ep leak. So handle return value of send_mpa_req()
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
->Stop the ep timer after MPA negotiation so that the arp failures
during send_mpa_reply/reject will be handled by process_timeout() after
the ep timer expires.
->Added case MPA_REP_SENT in process_timeout().
->For MPA reject, c4iw_ep_disconnect tries to start an already started
timer, which leads to warning message "timer already started".
-> In case of mpa reject stop the timer and call send_mpa_reject().
-> Added new ep flag STOP_MPA_TIMER to tell fw4_ack() to stop the timer
only for send_mpa_reply(), which is set in c4iw_accept_cr().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In case of incomplete mpa messages we should not stop timer as it
results in return with timeout for the next mpa message
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
failure
-> On passive side of connection parent_ep referenced during connection
request has to be dereferenced during the passive accept failure.
-> As passive accept failure error handlinglogic runs in atomic context,
the parent ep is dereferenced by scheduling work request.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
- add EP_DISC_FAIL history bit
- add QP_REFED/DEREFED history bits
- Add functions to ref/deref the cm_id and add history bit for the same
- add CLOSE_CON_RPL history
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Use c4iw_ep_disconnect() instead. This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
This is the last user of abort_connection(), so remove it too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In c4iw_ep_disconnect(), if we fail to initiate a close operation, then
move the qp to ERROR to disassociate the ep from the qp. Failure to do
this will leak the ep resources.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Instead return whether the caller needs to disconnect. This is part of
getting rid of abort_connection() altogether so we properly clean up on
send_abort() failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Use c4iw_ep_disconnect() instead. This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Instead, have the caller, rx_data() handle the close/abort like
it does for process_mpa_request(). This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In rx_data(), with the ep in FPDU_MODE, refcnt=2, if we get unexpected
streaming data, we call c4iw_modify_rc_qp() and move the qp from
RTS -> TERMINATE. In c4iw_modify_rc_qp(), if rdma_fini() returns
an error, the ep will be dereferenced (refcnt=1). Then rx_data()
calls c4iw_ep_disconnect() which starts the close operation.
But if send_halfclose() fails in c4iw_ep_disconnect(), we will call
release_ep_resources() derefing the ep which reduces the refcnt to 0 and
and frees the ep. However we still has the ep mutex at that point, so we
have a touch-after-free bug. There is a similar issue where
peer_close() calls c4iw_ep_disconnect().
The solution is to add a reference to the ep in c4iw_ep_disconnect()
after acquiring the mutex, and release it after releasing the mutex.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In c4iw_ep_disconnect(), if we start the ep timer to begin a close,
but send_halfclose() fails, we need to stop the timer and send a CLOSE
event up to the IWCM before releasing the resources. Otherwise, we can
crash when the ep timer fires if the ep is referencing a previous instance
of the device. This can happen as part of adapter reset/recovery, for
instance.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
If ARP fails before the CPL_PASS_ACCEPT_RPL is seen by hardware, the tid
will be stuck in SYN_PEND and never released. So create an arp failure
handler specifically for this message to release the endpoint resources.
In pass_accept_rpl_arp_failure(), put the parent endpoint so it will
be freed when destroyed. Also we don't need to call release_tid() here
because _c4iw_free_ep() calls cxgb4_remove_tid() which releases the
hwtid.
If we get an ABORT_REQ_RSS instead of a PASS_ESTABLISH (because the
peer's ACK to our SYN is never received), then put the parent as well
in peer_abort().
Treat accept_cr() failures just like arp failures: put the parent ep
and release the ep resources destroying the tid
The ARP failure handlers are called in an atomic context, so we need to
schedule some of the processing which might block. Namely _c4iw_free_ep()
which needs a mutex. So create a "special" CPL opcode and handler and
schedule it via sched() to be run by process_work() in a blockable context.
Also rework the active open arp failure handler to make use of
release_ep_resources(). This allows both the active and passive arp
failure handlers to use the same deferred cleanup function.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
|
|
Now that most of the port mapper code been moved to iwcm, we can remove
it from iw_cxgb4.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This series provides support for iWARP applications to specify a TOS
value and have that map to a VLAN Priority for iw_cxgb4 iWARP connections.
In iw_cxgb4, when allocating an L2T entry, pass the skb_priority based
on the tos value in the cm_id. Also pass the correct tos value during
connection setup so the passive side gets the client's desired tos.
When sending the FLOWC work request to FW, if the egress device is
in a vlan, then use the vlan priority bits as the scheduling class.
This allows associating RDMA connections with scheduling classes to
provide traffic shaping per flow.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Don't log errors if a listening endpoint is going away when procesing a
PASS_ACCEPT_REQ message. This can happen. Change the error printk to
a PDBG() debug log entry
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.5 merge window patches
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed
through the RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to
dependencies, acknowledged by Bruce)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (169 commits)
IB/mlx5: Unify CQ create flags check
IB/mlx5: Expose Raw Packet QP to user space consumers
{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib
IB/mlx5: Support setting Ethernet priority for Raw Packet QPs
IB/mlx5: Add Raw Packet QP query functionality
IB/mlx5: Add create and destroy functionality for Raw Packet QP
IB/mlx5: Refactor mlx5_ib_qp to accommodate other QP types
IB/mlx5: Allocate a Transport Domain for each ucontext
net/mlx5_core: Warn on unsupported events of QP/RQ/SQ
net/mlx5_core: Add RQ and SQ event handling
net/mlx5_core: Export transport objects
IB/mlx5: Expose CQE version to user-space
IB/mlx5: Add CQE version 1 support to user QPs and SRQs
IB/mlx5: Fix data validation in mlx5_ib_alloc_ucontext
IB/sa: Fix netlink local service GFP crash
IB/srpt: Remove redundant wc array
IB/qib: Improve ipoib UD performance
IB/mlx4: Advertise RoCE v2 support
IB/mlx4: Create and use another QP1 for RoCEv2
IB/mlx4: Enable send of RoCE QP1 packets with IP/UDP headers
...
|
|
The h/w is designed in such a way that, if you do anything IPv6
related, a valid clip entry must be there. So take clip reference
before creating IPv6 listening servers, and then if we fail to
create server, release the clip entry.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
|
|
This patch fix multiple spelling typos found in
various part of kernel.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The ESTABLISHED event should have the peer's ord/ird so
swap the values in the event before the upcall.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When calculating the minimum ird in c4iw_accept_cr(), we need to always
have a value of at least 1 if the RTR message is a 0B read. The code
was
incorrectly using ep->ord for this logic which was incorrectly adjusting
the ird and causing incorrect ord/ird negotiation when using MPAv2 to
negotiate these values.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This allows client ULPs to get the negotiated ord/ird which is useful
to avoid stalling the SQ due to exceeding the ORD.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In c4iw_create_listen(), if we're using listen filters, then bail out
of the busy loop if the device becomes fatally dead
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This fixes an if statement checking the return value of the function
get_lladdr for success in the function pick_local_ip6addrs to instead
of directly checking the return value of this call check the opposite
as get_lladdr returns zero for success which would incorrectly make
this if statement block not execute with the current if statement
check.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
