summaryrefslogtreecommitdiffstats
path: root/drivers/iio
AgeCommit message (Collapse)AuthorFilesLines
2017-08-28Merge 4.13-rc7 into staging-nextGreg Kroah-Hartman8-40/+100
We want the staging and iio fixes in here to handle the merge issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-20Merge tag 'iio-for-4.14b' of ↵Greg Kroah-Hartman24-205/+1180
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next Jonathan writes: Second set of IIO new device support, features and cleanup for the 4.14 cycle. New device support: * ak8974 - support the AMI306. * st_magnetometer - add support for the LIS2MDL with bindings. * rockchip-saradc - add binding for rv1108 SoC (no driver change). * srf08 - add srf02 (i2c only) and srf10 support. * stm32-timer - support for the STM32H7 to existing driver. Features: * tools - move over to the tools buildsystem rather than hand rolling. - add an install section to the build. * ak8974 - use serial number to add device randomness. - add AMI306 calibration data output. * ccs811 - triggered buffer support. * srf08 - add a device tree table as the old style i2c probing is going away, - add triggered buffer support * st32-adc - add optional st,min-sample-time-nsecs binding to allow control of sampling against analog circuitry. * stm32-timer - add output compare triggers. * ti-ads1015 - add threshold event support. * ti-ads7950 - Allow use on ACPI platforms including providing a default reference voltage as there is no way to obtain this on ACPI currently. Cleanup and fixes: * ad7606 - fix an error return code in probe. * ads1015 - fix incorrect data rate setting update when capture in progress, - fix wrong scale information for the ADS1115, - make conversions work when CONFIG_PM is not set, - make sure we don't get a stale result after a runtime resume by ensuring we wait long enough, - avoid returning a false error form the buffer setup callbacks, - add enough wait time to get the correct conversion, - remove an unnecessary config register update, - add a helper to set conversion mode reducing repeated boilerplate, - use devm_iio_triggered_buffer_setup to simplify error and remove paths, - use iio_device_claim_direct_mode instead of opencoding the same. * ak8974 - mark the INT_CLEAR register as precious to prevent debugfs access. * apds9300 - constify the i2c_device_id. * at91-sama5 adc - add missing Kconfig dependency. * bma180 accel - constify the i2c_device_id. * rockchip_saradc - explicitly request exclusive reset control as part of the reset rework on going throughout the kernel. * st_accel - fix drdy configuration for a load of accelerometers that only have the int1 line. Fix is unimportant as presumably no deviec tree actually used the non existent hardware line. * st_pressure - fix drdy configuration for LPS22HB and LPS25H by dropping int2 support as they don't have this. Fix is unimportant as presumably no device tree actually used the non existent hardware line. * stm32-dac - explicitly request exclusive reset control (part of reset being reworked). * tsl2583 - constify the i2c_device_id. * xadc - coding style fixes.
2017-08-20iio: adc: rockchip_saradc: explicitly request exclusive reset controlPhilipp Zabel1-1/+2
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting reset lines") started to transition the reset control request API calls to explicitly state whether the driver needs exclusive or shared reset control behavior. Convert all drivers requesting exclusive resets to the explicit API call so the temporary transition helpers can be removed. No functional changes. Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: linux-iio@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: dac: stm32-dac-core: explicitly request exclusive reset controlPhilipp Zabel1-1/+1
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting reset lines") started to transition the reset control request API calls to explicitly state whether the driver needs exclusive or shared reset control behavior. Convert all drivers requesting exclusive resets to the explicit API call so the temporary transition helpers can be removed. No functional changes. Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: linux-iio@vger.kernel.org Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: add threshold event supportAkinobu Mita1-2/+407
The ADS1015 device provides programmable comparator that can issue an interrupt on the ALERT pin. This change adds the iio threshold event support for that feature. The ADS1015 device only have a single config register which contains an input multiplexer selection, comparator settings, and etc. So only a single event channel can be enabled at a time. Also enabling both buffer and event are prohibited for simplicity. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: use iio_device_claim_direct_mode()Akinobu Mita1-8/+7
While the iio buffer for the ti-ads1015 driver is enabled, reading the raw ADC channel data is restricted. We usually use the iio_device_claim_direct_mode()/iio_device_release_direct_mode() pair for that. This change consequently reverses the locking order for the driver's private lock and indio_dev->mlock which acquired by iio_device_claim_direct_mode() internally. But it's safe because there is no other dependency between these locks. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: use devm_iio_triggered_buffer_setupAkinobu Mita1-12/+5
Use devm_iio_triggered_buffer_setup to simplify the error path in the probe() and remove() function. This changes the remove order, but the end result of remove function actually does the reverse of probe. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: add helper to set conversion modeAkinobu Mita1-12/+11
This adds a helper function to set conversion mode as there are a fair number of users. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: remove unnecessary config register updateAkinobu Mita1-14/+4
The ti-ads1015 driver has eight iio voltage channels and each iio channel can hold own scale information. The ADS1015 device only have a single config register which contains an input multiplexer selection, PGA and data rate settings. So the driver should load the correct settings when the input multiplexer selection is changed. However, regardless of which channlel is currently selected, changing any iio channel's scale information immediately overwrites the current PGA setting in the config register. It is harmless because the correct PGA settings are reloaded just before getting adc result anyway. But it is unnecessary register update and should be removed. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: add adequate wait time to get correct conversionAkinobu Mita1-12/+19
This driver assumes that the device is operating in the continuous conversion mode which performs the conversion continuously. So this driver inserts a wait time before reading the conversion register if the configuration is changed from a previous request. Currently, the wait time is only the period required for a single conversion that is calculated as the reciprocal of the sampling frequency. However we also need to wait for the the previous conversion to complete. Otherwise we probably get the conversion result for the previous configuration when the sampling frequency is lower. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: don't return invalid value from buffer setup callbacksAkinobu Mita1-1/+1
pm_runtime_get_sync() and pm_runtime_put_autosuspend() return 0 on success, 1 if the device's runtime PM status was already requested status or error code on failure. So a positive return value doesn't indicate an error condition. However, any non-zero return values from buffer preenable and postdisable callbacks are recognized as an error and this driver reuses the return value from pm_runtime_get_sync() and pm_runtime_put_autosuspend() in these callbacks. This change fixes the false error detections. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: avoid getting stale result after runtime resumeAkinobu Mita1-2/+16
This driver assumes that the device is operating in the continuous conversion mode which performs the conversion continuously. So this driver doesn't insert a wait time before reading the conversion register if the configuration is not changed from a previous request. This assumption is broken if the device is runtime suspended and entered a power-down state. The forthcoming request causes reading a stale result from the conversion register as the device is runtime resumed just before. Fix it by adding a flag to detect that condition and insert a necessary wait time. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: enable conversion when CONFIG_PM is not setAkinobu Mita1-0/+7
The ADS1015 device have two operating modes, continuous conversion mode and single-shot mode. This driver assumes that the continuous conversion mode is selected by runtime resume callback when the ADC result is requested. If CONFIG_PM is disabled, the device is always in the default single-shot mode and no one begins a single conversion. So the conversion register doesn't contain valid ADC result. Fix it by changing the continuous mode in probe function. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: fix scale information for ADS1115Akinobu Mita1-24/+24
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same scale information is used for both devices in this driver, however they have actually different values and the ADS1115's one is not correct. These devices have the same full-scale input voltage range for each PGA selection. So instead of adding another hardcoded scale information, compute a correct scale on demand from each device's resolution. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads1015: fix incorrect data rate setting updateAkinobu Mita1-17/+10
The ti-ads1015 driver has eight iio voltage channels and each iio channel can hold own sampling frequency information. The ADS1015 device only have a single config register which contains an input multiplexer selection, PGA and data rate settings. So the driver should load the correct settings when the input multiplexer selection is changed. However, regardless of which channlel is currently selected, changing any iio channel's sampling frequency information immediately overwrites the current data rate setting in the config register. It breaks the current data rate setting if the different channel's sampling frequency information is changed because the data rate setting is not reloaded when the input multiplexer is switched. This removes the unexpected config register update and correctly load the data rate setting before getting adc result. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: adc: ti-ads7950: Allow to use on ACPI platformsAndy Shevchenko1-4/+20
ACPI enabled platforms do not have a mean of regulators. Instead we use hard coded voltage value for reference pin. When value is 0 (default) we fall back to request a regulator. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: magnetometer: ak8974: debug AMI306 calibration dataMichał Mirosław1-0/+41
Use AMI306 calibration data for randomness and debugging. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: magnetometer: st_magn: remove ihl property for LSM303AGRLorenzo Bianconi1-2/+0
Remove IRQ active low support for LSM303AGR since the sensor does not support that capability for data-ready line Fixes: a9fd053b56c6 (iio: st_sensors: support active-low interrupts) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: magnetometer: st_magn: fix status register address for LSM303AGRLorenzo Bianconi1-1/+1
Fixes: 97865fe41322 (iio: st_sensors: verify interrupt event to status) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: hid-sensor-trigger: Fix the race with user space powering up sensorsSrinivas Pandruvada1-4/+4
It has been reported for a while that with iio-sensor-proxy service the rotation only works after one suspend/resume cycle. This required a wait in the systemd unit file to avoid race. I found a Yoga 900 where I could reproduce this. The problem scenerio is: - During sensor driver init, enable run time PM and also set a auto-suspend for 3 seconds. This result in one runtime resume. But there is a check to avoid a powerup in this sequence, but rpm is active - User space iio-sensor-proxy tries to power up the sensor. Since rpm is active it will simply return. But sensors were not actually powered up in the prior sequence, so actaully the sensors will not work - After 3 seconds the auto suspend kicks If we add a wait in systemd service file to fire iio-sensor-proxy after 3 seconds, then now everything will work as the runtime resume will actually powerup the sensor as this is a user request. To avoid this: - Remove the check to match user requested state, this will cause a brief powerup, but if the iio-sensor-proxy starts immediately it will still work as the sensors are ON. - Also move the autosuspend delay to place when user requested turn off of sensors, like after user finished raw read or buffer disable Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Tested-by: Bastien Nocera <hadess@hadess.net> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: trigger: stm32-timer: fix get trigger modeFabrice Gasnier1-1/+1
Fix reading trigger mode, when other bit-fields are set. SMCR register value must be masked to read SMS (slave mode selection) only. Fixes: 9eba381 ("iio: make stm32 trigger driver use INDIO_HARDWARE_TRIGGERED mode") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: imu: adis16480: Fix acceleration scale factor for adis16480Dragos Bogdan1-1/+1
According to the datasheet, the range of the acceleration is [-10 g, + 10 g], so the scale factor should be 10 instead of 5. Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: magnetometer: ak8974: mark INT_CLEAR as preciousMichał Mirosław1-0/+6
Reading INT_CLEAR has side effects - disallow reading it via debugfs. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: magnetometer: ak8974: add_device_randomness (serial number)Michał Mirosław1-0/+2
Mix device-specific data into randomness pool. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: magnetometer: ak8974: support AMI306 variantMichał Mirosław2-22/+72
Add support for AMI306 magnetometer - very similar to AMI305. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: light: tsl2583: constify i2c_device_idArvind Yadav1-1/+1
i2c_device_id are not supposed to change at runtime. All functions working with i2c_device_id provided by <linux/i2c.h> work with const i2c_device_id. So mark the non-const structs as const. Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: light: apds9300: constify i2c_device_idArvind Yadav1-1/+1
i2c_device_id are not supposed to change at runtime. All functions working with i2c_device_id provided by <linux/i2c.h> work with const i2c_device_id. So mark the non-const structs as const. Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20iio: accel: bma180: constify i2c_device_idArvind Yadav1-1/+1
i2c_device_id are not supposed to change at runtime. All functions working with i2c_device_id provided by <linux/i2c.h> work with const i2c_device_id. So mark the non-const structs as const. Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-18iio: chemical: ccs811: Add triggered buffer supportNarcisa Ana Maria Vasile2-5/+73
A software trigger such as hrtimer can be used to capture the data that will be stored in the buffer. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Alison Schofield <amsfield22@gmail.com> Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-18iio: srf08: add support for srf02 in i2c modeAndreas Klinger2-22/+67
srf02 added with support for i2c interface Attributes for setting max range or sensitivity are omitted for the case of srf02 type sensor, because they are not supported by the hardware. Signed-off-by: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-18iio: srf08: add sensor type srf10Andreas Klinger2-17/+77
Ultrasonic sensor srf10 is quite similar to srf08 and now also supported by the driver as device tree compatible string. It was necessary to prepare the source for supplementary sensors. This is done by enum srf08_sensor_type. The most significiant difference between srf08 and srf10 is another range and values of register gain (in the driver it's call sensitivity). Therefore the array of it is extended and dependent of the sensor type. Signed-off-by: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-18iio: srf08: add triggered buffer supportAndreas Klinger1-3/+57
Add support for triggered buffers. Data format is quite simple: distance 16 Bit alignment 48 Bit timestamp 64 Bit Signed-off-by: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-18iio: srf08: add device tree tableAndreas Klinger1-0/+8
Added MODULE_DEVICE_TABLE for device tree bindings. It used to work without it by using the i2c_device_id table, but adding the table makes everything clear and documented. Signed-off-by: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-17iio: magnetometer: add support to LIS2MDLLorenzo Bianconi4-0/+12
add support to STMicroelectronics LIS2MDL magnetometer in st_magn framework http://www.st.com/resource/en/datasheet/lis2mdl.pdf Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-17iio: adc: select triggered buffer for sama5d2 adcArnd Bergmann1-0/+1
Without the triggered buffer code, we get a link error: drivers/iio/adc/at91-sama5d2_adc.o: In function `at91_adc_probe': at91-sama5d2_adc.c:(.text+0x938): undefined reference to `devm_iio_triggered_buffer_setup' This adds a Kconfig 'select' statement like other ADC drivers have it already. Fixes: 5e1a1da0f8c9 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-14Merge 4.13-rc5 into staging-nextGreg Kroah-Hartman9-14/+133
We need it here for iio fixes. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-12iio: accel: st_accel: fix data-ready line configurationLorenzo Bianconi1-2/+2
Remove int2 configuration parameter for LIS3DH, LSM303DLHC, LSM330D, LSM330DL, LSM330DLC, LSM303AGR, LIS2DH12 and LNG2DM since these devices export just int1 as data-ready line Fixes: 23cde4d65cc7 (iio: Added platform data to select the DRDY pin) Fixes: dcdb0a78cab3 (iio: accel: st_accel: add support to lng2dm) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-12iio: pressure: st_pressure: fix drdy configuration for LPS22HB and LPS25HLorenzo Bianconi1-2/+2
Remove int2 configuration parameter for LPS22HB and LPS25H since these devices export just int1 as data-ready line Fixes: 931878405b86 (iio:pressure: Add support for LPS25H pressure sensor) Fixes: e039e2f5b4da (iio:st_pressure:initial lps22hb sensor support) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-12iio: adc: xadc: Fix coding style violationsSai Krishna Potthuri2-25/+23
This patch fix following checkpatch warnings in xadc driver 1. prefer 'unsigned int' to bare use of 'unsigned'. 2. else is not generally useful after a break or return. 3. fill all function definition arguments with identifier name Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-12iio: trigger: stm32-timer: add output compare triggersFabrice Gasnier1-11/+20
Add output compare trigger sources available on some instances. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-12iio: trigger: stm32-timer: add support for STM32H7Fabrice Gasnier1-4/+51
Add support for STM32H7 timer triggers: - Add new valids_table - Introduce compatible, with configuration data - Extend up to 15 timers, available on STM32H7 Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-09iio: adc: ti-ads7950: Add OF device ID tableAndy Shevchenko1-0/+18
The driver doesn't have a struct of_device_id table but supported devices are registered via Device Trees. This is working on the assumption that a SPI device registered via OF will always match a legacy SPI device ID and that the MODALIAS reported will always be of the form spi:<device>. There is an ACPI method to enumerate such devices via specific ACPI ID and use of compatible strings. It will not work for the drivers which have no OF match ID table present. Besides this could change in the future so the correct approach is to have an OF device ID table if the devices are registered via OF. Tested-by: David Lechner <david@lechnology.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-09iio: adc: stm32: add optional st,min-sample-time-nsecsFabrice Gasnier1-4/+136
STM32 ADC allows each channel to be sampled with a different sampling time, by setting SMPR registers. Basically, value depends on local electrical properties. Selecting correct value for sampling time highly depends on analog source impedance. There is a manual that may help in this process: 'How to get the best ADC accuracy in STM32...' This patch allows to configure minimum sampling time via device tree, either for: - all channels at once: st,min-sample-time-nsecs = <10000>; - independently for each channel (must match "st,adc-channels" list): st,adc-channels = <0 1>; st,min-sample-time-nsecs = <5000 10000>; Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-30iio: adc: stm32: fix common clock rateFabrice Gasnier1-5/+5
ADC clock input is provided to internal prescaler (that decreases its frequency). It's then used as reference clock for conversions. - Fix common clock rate used then by stm32-adc sub-devices. Take common prescaler into account. Currently, rate is used to set "boost" mode. It may unnecessarily be set. This impacts power consumption. - Fix ADC max clock rate on STM32H7 (fADC from datasheet). Currently, prescaler may be set too low. This can result in ADC reference clock used for conversion to exceed max allowed clock frequency. Fixes: 95e339b6e85d ("iio: adc: stm32: add support for STM32H7") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-30iio: adc: ina219: Avoid underflow for sleeping timeStefan Brüns1-1/+1
Proper support for the INA219 lowered the minimum sampling period from 2*140us to 2*84us. Subtracting 200us later leads to an underflow and an almost infinite udelay later. Using a signed int for the sampling period provides sufficient range (at most 2*8640*1024us), but catches the underflow when comparing with buffer_us. Fixes: 18edac2e22f4 ("iio: adc: Fix integration time/averaging for INA219/220") Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-30iio: trigger: stm32-timer: add enable attributeFabrice Gasnier1-14/+41
In order to use encoder mode, timers needs to be enabled (e.g. CEN bit) along with peripheral clock. Add IIO_CHAN_INFO_ENABLE attribute to handle this. Also, in triggered mode, CEN bit is set automatically in hardware. Then clock must be enabled before starting triggered mode. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-30iio: trigger: stm32-timer: fix get/set down count directionFabrice Gasnier1-4/+11
Fixes: 4adec7da0536 ("iio: stm32 trigger: Add quadrature encoder device") This fixes two issues: - stm32_set_count_direction: to set down direction - stm32_get_count_direction: to get down direction IIO core provides/expects value to be an index of iio_enum items array. This needs to be turned by these routines into TIM_CR1_DIR (e.g. BIT(4)) value. Also, report error when attempting to write direction, when in encoder mode: in this case, direction is read only (given by encoder inputs). Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-30iio: trigger: stm32-timer: fix write_raw return valueFabrice Gasnier1-2/+1
Fixes: 4adec7da0536 ("iio: stm32 trigger: Add quadrature encoder device") IIO core expects zero as return value for write_raw() callback in case of success. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-30iio: trigger: stm32-timer: fix quadrature mode get routineFabrice Gasnier1-2/+5
Fixes: 4adec7da0536 ("iio: stm32 trigger: Add quadrature encoder device") SMS bitfiled is mode + 1. After reset, upon boot, SMS = 0. When reading from sysfs, stm32_get_quadrature_mode() returns -1 (e.g. -EPERM) which is wrong error code here. So, check SMS bitfiled matches valid encoder mode, or return -EINVAL. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-30iio: bmp280: properly initialize device for humidity readingAndreas Klinger2-3/+29
If the device is not initialized at least once it happens that the humidity reading is skipped, which means the special value 0x8000 is delivered. For omitting this case the oversampling of the humidity must be set before the oversampling of the temperature und pressure is set as written in the datasheet of the BME280. Furthermore proper error detection is added in case a skipped value is read from the device. This is done also for pressure and temperature reading. Especially it don't make sense to compensate this value and treat it as regular value. Signed-off-by: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-08-29 06:36:28 +0000