| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
At probe, runtime pm should be setup before registering the sysfs interface so
that all the power attributes are accurate and functional when registering.
Also, when removing the device we should unregister first to make sure
that the interfaces that may result in wakeups are no longer available.
Fix this behaviour for the following drivers: bmc150, bmg160, kmx61,
kxcj-1013, mma9551, mma9553, rpr0521.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The return value of gpiod_to_irq should be checked before giving
it to devm_request_threaded_irq in order to not pass an error
code in case it fails.
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Since 39b2bbe3d715 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
outputs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Freescale has the MMA955xL family of devices that use the
same communication protocol (based on i2c messages):
http://www.freescale.com/files/sensors/doc/data_sheet/MMA955xL.pdf.
To support more devices from this family, we need to split the
mma9551 driver so we can export the common functions that will
be used by other mma955x drivers.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add support for runtime pm to reduce the power consumed by the device
when not used.
If CONFIG_PM is not enabled, the device will be powered on at
init and only powered off on system suspend.
If CONFIG_PM is enabled, runtime pm autosuspend is used:
- for raw reads will keep the device on for a specified time
- for events it will keep the device on as long as we have at least
one event active
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
sparse warnings: (new ones prefixed by >>)
>> drivers/iio/accel/mma9551.c:554:57: sparse: mixing different enum types
drivers/iio/accel/mma9551.c:554:57: int enum mma9551_tilt_axis versus
drivers/iio/accel/mma9551.c:554:57: int enum mma9551_gpio_pin
>> drivers/iio/accel/mma9551.c:576:57: sparse: mixing different enum types
drivers/iio/accel/mma9551.c:576:57: int enum mma9551_tilt_axis versus
drivers/iio/accel/mma9551.c:576:57: int enum mma9551_gpio_pin
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add support for Freescale MMA9551L Intelligent Motion-Sensing Platform.
The driver supports raw reads for acceleration and inclination, as well
as configuring inclination rate-of-change events. The events can be
used similarly to an Android sensor Tilt event.
The specifications can be downloaded from:
http://www.freescale.com/files/sensors/doc/ref_manual/MMA955xLSWRM.pdf
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
