summaryrefslogtreecommitdiffstats
path: root/drivers/i2c
AgeCommit message (Collapse)AuthorFilesLines
2009-07-30i2c-omap: OMAP3430 Silicon Errata 1.153Sonasath, Moiz1-1/+23
When an XRDY/XDR is hit, wait for XUDF before writing data to DATA_REG. Otherwise some data bytes can be lost while transferring them from the memory to the I2C interface. Do a Busy-wait for XUDF, before writing data to DATA_REG. While waiting if there is NACK | AL, set the appropriate error flags, ack the pending interrupts and return from the ISR. Signed-off-by: Moiz Sonasath <m-sonasath@ti.com> Signed-off-by: Vikram pandita <vikram.pandita@ti.com> [ben-linux@fluff.org: fixed mail format and added i2c-omap to subject] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-30i2c-omap: In case of a NACK|ARDY|AL return from the ISRSonasath, Moiz1-1/+3
In case of a NACK or ARDY or AL interrupt, complete the request. There is no need to service the RRDY/RDR or XRDY/XDR interrupts. Refer TRM SWPU114: Figure 18-31.I2C Master Transmitter Mode, Interrupt Method, in F/S and HS Modes http://focus.ti.com/pdfs/wtbu/SWPU114T_PrelimFinalEPDF_06_25_2009.pdf Signed-off-by: Moiz Sonasath <m-sonasath@ti.com> Signed-off-by: Vikram pandita <vikram.pandita@ti.com> [ben-linux@fluff.org: fixed mail format and added i2c-omap to subject] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-30i2c-omap: Bug in reading the RXSTAT/TXSTAT values from the I2C_BUFFSTAT registerSonasath, Moiz1-5/+7
Fix bug in reading the I2C_BUFFSTAT register for getting byte count on RX/TX interrupt. On Interrupt: I2C_STAT[RDR], read 'RXSTAT' from I2C_BUFFSTAT[8-13] On Interrupt: I2C_STAT[XDR] read 'TXSTAT' from I2C_BUFFSTAT[0-5] Signed-off-by: Jagadeesh Pakaravoor <j-pakaravoor@ti.com> Signed-off-by: Moiz Sonasath <m-sonasath@ti.com> Signed-off-by: Vikram pandita <vikram.pandita@ti.com> [ben-linux@fluff.org: fixed mail format and added i2c-omap to subject] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-30i2c-sh_mobile: change module_init() to subsys_initcall()Magnus Damm1-1/+1
Convert the i2c-sh_mobile i2c bus driver to use subsys_initcall() instead of module_init(). This change makes the driver register a bit earlier which together with earlier platform data moves the time for probe(). The earlier probe() makes it possible to use i2c_get_adapter() and i2c_transfer() from device_initcall(). The same strategy is used by other i2c bus drivers such as i2c-pxa.c and i2c-s3c2410.c. Signed-off-by: Magnus Damm <damm@igel.co.jp> [ben-linux@fluff.org: minor subject updaye] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-30i2c: strncpy does not null terminate stringRoel Kluin1-1/+1
strlcpy() will always null terminate the string. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-30i2c-s3c2410: s3c24xx_i2c_init: don't clobber IICLC valuePeter Korsgaard1-5/+0
s3c24xx_i2c_init() was overwriting the IICLC value set just above in s3c24xx_i2c_clockrate() with zero, effectively disabling the platform line control setting. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-28i2c/tsl2550: Fix lux value in dark environmentMichele Jr De Candia1-7/+10
I've tested TSL2550 driver and I've found a bug: when light is off, returned value from tsl2550_calculate_lux function is -1 when it should be 0 (sensor correctly read that light was off). I think the bug is that a zero c0 value (approximated value of ch0) is misinterpreted as an error. Signed-off-by: Michele Jr De Candia <michele.decandia@valueteam.com> Acked-by: Rodolfo Giometti <giometti@linux.it> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-07-15i2c: Use resource_sizeJulia Lawall4-8/+8
Use the function resource_size, which reduces the chance of introducing off-by-one errors in calculating the resource size. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ struct resource *res; @@ - (res->end - res->start) + 1 + resource_size(res) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-15i2c-davinci: behave with i2cdetectDavid Brownell1-4/+14
Make i2c-davinci cope properly with "i2cdetect": don't spew syslog spam on perfectly normal behaviors, or respond to any address other than the one reserved for the SMBus host. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-15i2c-davinci: convert clock usage after clkdev conversionKevin Hilman1-1/+1
DaVinci core code has converted to the new clkdev API so clock name strings are not needed. Instead, just the a 'struct device' pointer is needed. Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-08Remove multiple KERN_ prefixes from printk formatsJoe Perches1-4/+5
Commit 5fd29d6ccbc98884569d6f3105aeca70858b3e0f ("printk: clean up handling of log-levels and newlines") changed printk semantics. printk lines with multiple KERN_<level> prefixes are no longer emitted as before the patch. <level> is now included in the output on each additional use. Remove all uses of multiple KERN_<level>s in formats. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-25i2c: fix build bug in i2c-designware.cIngo Molnar1-0/+1
This build error triggers on x86: drivers/built-in.o: In function `i2c_dw_init': i2c-designware.c:(.text+0x4e37ca): undefined reference to `clk_get_rate' drivers/built-in.o: In function `dw_i2c_probe': i2c-designware.c:(.devinit.text+0x51f5e): undefined reference to `clk_get' i2c-designware.c:(.devinit.text+0x51f76): undefined reference to `clk_enable' i2c-designware.c:(.devinit.text+0x520ff): undefined reference to `clk_disable' i2c-designware.c:(.devinit.text+0x52108): undefined reference to `clk_put' Because this new driver uses the clk_*() facilities which is an ARM-only thing currently. Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-24i2c: driver for the Synopsys DesignWare I2C controllerBaruch Siach3-0/+634
The i2c Linux driver for the DesignWare i2c block of Synopsys, which is meant for AMBA Peripheral Bus. This i2c block is used on SoC chips like the ARM9 based PVG610. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-22i2c: Fix stuck transaction on cpm-i2c driverMichael Trimarchi1-3/+3
When a process tries to read/write a disconnected i2c device, it receives a signal (e.g. ctrl-c) and the kernel gets stuck. BUG: soft lockup - CPU#0 stuck for 61s! [I2CEEpromTest:392] NIP: c01628f8 LR: c01628f0 CTR: c00177cc REGS: c39abd70 TRAP: 0901 Not tainted (2.6.25.7-alcore) MSR: 00009032 <EE,ME,IR,DR> CR: 42042048 XER: 20000000 TASK = c3889bd0[392] 'I2CEEpromTest' THREAD: c39aa000 GPR00: 00009000 c39abe20 c3889bd0 c39075c8 c39abe28 00000001 00000000 00000001 GPR08: c3889bd0 c39075c8 00009032 c39abe34 00002437 NIP [c01628f8] cpm_i2c_xfer+0x5fc/0x6d0 LR [c01628f0] cpm_i2c_xfer+0x5f4/0x6d0 Call Trace: [c39abe20] [c0162924] cpm_i2c_xfer+0x628/0x6d0 (unreliable) [c39abe90] [c015f6a0] i2c_transfer+0x88/0xb4 [c39abeb0] [c0160164] i2c_master_recv+0x48/0x6c [c39abed0] [c01618dc] i2cdev_read+0x50/0xe4 [c39abef0] [c0068b24] vfs_read+0xc4/0x108 [c39abf10] [c0068f4c] sys_read+0x4c/0x90 [c39abf40] [c000d348] ret_from_syscall+0x0/0x38 Instruction dump: 3bc00064 92610010 3bf201c8 92810014 3b61 This happen because though the wait_event_interruptible_timeout takes the signals into account, the driver does not handle them. We propose to change the wait_event_interruptible_timeout with wait_event_timeout, leaving the signals to be handled in other points on the upper layers. Signed-off-by: Bruno Morelli <bruno@evidence.eu.com> Signed-off-by: Michael Trimarchi <michael@evidence.eu.com> Acked-by: Jochen Friedrich <jochen@scram.de> [ben-linux@fluff.org: fix title for patch] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-22i2c-omap: Fix build breaking typo cpu_is_omap_2430Tony Lindgren1-1/+1
Hi Ben, Can you please queue this fix? Thanks, Tony >From ffe2b2cdf6283770b70a197e3748c6b40a1006be Mon Sep 17 00:00:00 2001 From: Tony Lindgren <tony@atomide.com> Date: Wed, 17 Jun 2009 13:14:23 +0300 Subject: [PATCH] i2c-omap: Fix build breaking typo in cpu_is_omap_2430 Commit 84bf2c86 introduced a typo, it should be cpu_is_omap2430 instead. The typo was probably caused by a mismerge. Without this patch all omaps fail to build with: error: implicit declaration of function 'cpu_is_omap_2430' Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-19Merge branch 'i2c-for-linus' of ↵Linus Torvalds3-363/+205
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging * 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: i2c: New macro to initialize i2c address lists on the fly i2c: Don't advertise i2c functions when not available i2c: Use rwsem instead of mutex for board info i2c: Add a sysfs interface to instantiate devices i2c: Limit core locking to the necessary sections i2c: Kill the redundant client list i2c: Kill is_newstyle_driver i2c: Merge i2c_attach_client into i2c_new_device i2c: Drop i2c_probe function i2c: Get rid of the legacy binding model i2c: Kill client_register and client_unregister methods
2009-06-19i2c: Use rwsem instead of mutex for board infoRodolfo Giometti3-6/+10
By using rwsem we can easily manage recursive calls of i2c_scan_static_board_info() function without breaking the locking. Signed-off-by: Rodolfo Giometti <giometti@linux.it> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-19i2c: Add a sysfs interface to instantiate devicesJean Delvare1-1/+122
Add a sysfs interface to instantiate and delete I2C devices. This is primarily a replacement of the force_* module parameters implemented by some i2c drivers. These module parameters were implemented internally by the I2C_CLIENT_INSMOD* macros, which don't scale well. This can also be used when developing a driver on a self-soldered board which doesn't yet have proper I2C device declaration at the platform level, and presumably for various debugging situations. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19i2c: Limit core locking to the necessary sectionsJean Delvare1-23/+28
The i2c-core code tends to hold the core lock for longer than it should. Limit locking to the necessary sections for both performance and clarity. This is also a requirement to support I2C multiplexers in the future. Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Rodolfo Giometti <giometti@linux.it> Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19i2c: Kill the redundant client listJean Delvare1-17/+11
We used to maintain our own per-adapter list of i2c clients, but this is redundant with what the driver core does, and no longer needed. Just drop the redundant list. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19i2c: Kill is_newstyle_driverJean Delvare1-31/+1
Legacy i2c drivers are gone, all drivers are new-style now, so there is no point to check. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19i2c: Merge i2c_attach_client into i2c_new_deviceJean Delvare1-59/+41
Now that i2c_attach_client is no longer exported, it doesn't need to be a separate function. Merge it into its only user, i2c_new_device. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19i2c: Drop i2c_probe functionJean Delvare1-137/+0
The legacy i2c_probe() function has no users left, get rid of it. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19i2c: Get rid of the legacy binding modelJean Delvare1-76/+7
We converted all the legacy i2c drivers so we can finally get rid of the legacy binding model. Hooray! Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19i2c: Kill client_register and client_unregister methodsJean Delvare1-29/+1
These methods were useful in the legacy binding model but no longer in the new (standard) binding model. There are no users left so we can drop them. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-18Merge commit 'gcl/merge' into nextBenjamin Herrenschmidt1-1/+1
Manual merge of: drivers/net/fec_mpc52xx.c
2009-06-17powerpc/5xxx: Add common mpc5xxx_get_bus_frequency() functionWolfgang Denk1-1/+1
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency, while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different clock names (IPS vs. IPB) the code was identical. Use common code for both processor families. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-06-16i2c-stu300: Make driver depend on MACH_U300Linus Walleij1-0/+1
This makes the stu300 driver for the ST Micro ST DDC I2C bus driver depend on MACH_U300, new platforms reusing this I2C driver will need to add in a similar dependency. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> [ben-linux@fluff.org: re-aranged subject line] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-16i2c-s3c2410: use resource_size()Ben Dooks1-2/+2
Change the usage of res->end-res->start to resource_size(), missed by the last patch to change this. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-16i2c: Use resource_size macroLinus Walleij11-31/+28
This replace all instances in the i2c busses tree of res->end - res->start + 1 with the handy macro resource_size(res) from ioport.h (coming in from platform_device.h). This was created with a simple sed -i -e 's/\([a-z]*\)->end *- *[a-z]*->start *+ *1/resource_size(\1)/g' Then manually replacing the PXA redefiniton of the same kind of macro manually. Recompiled some ARM defconfigs I could find to make a rough test so it shouldn't break anything, though I couldn't see exactly which configs you need for all the drivers. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-16i2c: ST DDC I2C U300 bus driver v3Linus Walleij3-0/+1042
This adds support for the ST Microelectronics DDC I2C bus driver. This bus is used in the U300 architecture recently added to RMK:s ARM tree. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Reviewed-by: Ben Dooks <ben-linux@fluff.org> Reviewed-by: Jean Delvare <khali@linus-fr.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-16i2c-bfin-twi: pull in io.h for ioremap()Mike Frysinger1-0/+1
Rather than relying on some of the headers implicitly pulling in io.h, pull it in explicitly our self for ioremap() and friends. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-16Merge branch 'i2c-for-linus' of ↵Linus Torvalds7-282/+34
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging * 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: therm_windtunnel: Convert to a new-style i2c driver therm_adt746x: Convert to a new-style i2c driver windfarm: Convert to new-style i2c drivers therm_pm72: Convert to a new-style i2c driver i2c-viapro: Add new PCI device ID for VX855 i2c/chips: Move max6875 to drivers/misc/eeprom i2c: Do not give adapters a default parent i2c: Do not probe for TV chips on Voodoo3 adapters i2c: Retry automatically on arbitration loss i2c: Remove void casts
2009-06-15Merge branch 'merge' of ↵Linus Torvalds1-3/+3
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits) powerpc: Fix bug in move of altivec code to vector.S powerpc: Add support for swiotlb on 32-bit powerpc/spufs: Remove unused error path powerpc: Fix warning when printing a resource_size_t powerpc/xmon: Remove unused variable in xmon.c powerpc/pseries: Fix warnings when printing resource_size_t powerpc: Shield code specific to 64-bit server processors powerpc: Separate PACA fields for server CPUs powerpc: Split exception handling out of head_64.S powerpc: Introduce CONFIG_PPC_BOOK3S powerpc: Move VMX and VSX asm code to vector.S powerpc: Set init_bootmem_done on NUMA platforms as well powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock powerpc/mm: Fix some SMP issues with MMU context handling powerpc: Add PTRACE_SINGLEBLOCK support fbdev: Add PLB support and cleanup DCR in xilinxfb driver. powerpc/virtex: Add ml510 reference design device tree powerpc/virtex: Add Xilinx ML510 reference design support powerpc/virtex: refactor intc driver and add support for i8259 cascading powerpc/virtex: Add support for Xilinx PCI host bridge ...
2009-06-15i2c-viapro: Add new PCI device ID for VX855Harald Welte2-3/+7
The south bridge of the VIA VX855 chipset has a different PCI Device ID so i2c-viapro.c needs to be updated with this. Signed-off-by: Harald Welte <HaraldWelte@viatech.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15i2c/chips: Move max6875 to drivers/misc/eepromWolfram Sang3-262/+0
This driver only reads the user EEPROM of that chip, so we can move it to the eeprom-directory in order to further clean up (and later remove) drivers/i2c/chips. The Kconfig text was updated to match the current functionality, dropping the meanwhile obsoleted parts. Defconfigs have been adapted. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Ben Gardner <gardner.ben@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15i2c: Do not give adapters a default parentJean Delvare1-11/+0
We don't need to give adapters a parent if they don't have one. The driver core will put them in the virtual device directory and all will be fine. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15i2c: Do not probe for TV chips on Voodoo3 adaptersJean Delvare1-1/+0
There's no point in giving the I2C bus of Voodoo3 adapters a class value, there's no video chip driver checking for it anymore. If support is ever needed, the video device should be instantiated explicitly rather than probed. To the best of my knowledge the only video chip that can be found on these boards is a BT869 video encoder, for which no support exists currently. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
2009-06-15i2c: Retry automatically on arbitration lossClifford Wolf1-4/+26
Some small changes in i2c core to retry i2c xfers until either the maximum number of retries or the timeout is hit. Signed-off-by: Clifford Wolf <clifford@clifford.at> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15i2c: Remove void castsJack Stone1-1/+1
Remove uneeded void casts. Signed-off-by: Jack Stone <jwjstone@fastmail.fm> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15Merge commit 'origin/master' into nextBenjamin Herrenschmidt6-57/+118
2009-06-14Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds1-3/+19
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits) MAINTAINERS: EB110ATX is not ebsa110 MAINTAINERS: update Eric Miao's email address and status fb: add support of LCD display controller on pxa168/910 (base layer) [ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN [ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines [ARM] 5544/1: Trust PrimeCell resource sizes [ARM] pxa/sharpsl_pm: cleanup of gpio-related code. [ARM] pxa/sharpsl_pm: drop set_irq_type calls [ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one [ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific [ARM] sa1100: remove unused collie_pm.c [ARM] pxa: fix the conflicting non-static declarations of global_gpios[] [ARM] 5550/1: Add default configure file for w90p910 platform [ARM] 5549/1: Add clock api for w90p910 platform. [ARM] 5548/1: Add gpio api for w90p910 platform [ARM] 5551/1: Add multi-function pin api for w90p910 platform. [ARM] Make ARM_VIC_NR depend on ARM_VIC [ARM] 5546/1: ARM PL022 SSP/SPI driver v3 ARM: OMAP4: SMP: Update defconfig for OMAP4430 ARM: OMAP4: SMP: Enable SMP support for OMAP4430 ...
2009-06-13i2c-ocores: Can add I2C devices to the busRichard Röjfors1-0/+5
There is sometimes a need for the ocores driver to add devices to the bus when installed. i2c_register_board_info can not always be used, because the I2C devices are not known at an early state, they could for instance be connected on a I2C bus on a PCI device which has the Open Cores IP. i2c_new_device can not be used in all cases either since the resulting bus nummer might be unknown. The solution is the pass a list of I2C devices in the platform data to the Open Cores driver. This is useful for MFD drivers. Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-13i2c-s3c2410: move to using platform idtable to match devicesBen Dooks1-26/+22
Change to using platform id table to match either of the two supported platform device names in the driver. This simplifies the driver init and exit code Note, log messages will now be prefixed with 's3c-i2c' instead of the driver name, so output will be of the form of: s3c-i2c s3c2440-i2c.0: slave address 0x10 Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-13i2c: OMAP3: Better noise suppression for fast/standard modesAaro Koskinen1-2/+12
Use longer noise filter period for fast and standard mode. Based on an earlier patch by Eero Nurkkala. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-13i2c: OMAP2/3: Fix scll/sclh calculationsAaro Koskinen1-7/+18
Fix scll/sclh calculations for HS and fast modes. Currently the driver uses equal (roughly) low/high times which will result in too short low time. OMAP3430 TRM gives the following equations: F/S: tLow = (scll + 7) * internal_clk tHigh = (sclh + 5) * internal_clk HS: tLow = (scll + 7) * fclk tHigh = (sclh + 5) * fclk Furthermore, the I2C specification sets the following minimum values for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400) and 400 pF (maximum speed 1700): speed tLow tHigh 3400 160 ns 60 ns 1700 320 ns 120 ns and for F/S: speed tLow tHigh 400 1300 ns 600 ns 100 4700 ns 4000 ns By using duty cycles 33/66 (HS, F) and 50/50 (S) we stay above these minimum values. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-13i2c: Blackfin TWI: implement I2C_FUNC_SMBUS_I2C_BLOCK functionalityMichael Hennerich1-1/+11
Some drivers need i2c_smbus_read_i2c_block_data() functionality, so add support for it to the Blackfin I2C bus driver. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> [ben-linux@fluff.org: shortened subject] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-13i2c: Blackfin TWI: fix transfer errors with repeat startFrank Shew1-6/+15
We have a custom BF537 board with an I2C RTC (MAX DS3231) running uclinux 2007R1 for some time. Recently during migration to 2008R1.5-RC3 we losted access to the RTC. The RTC driver calls 'i2c_transfer()' which in turns calls 'bfin_twi_master_xfer()' in i2c-bfin-twi.c. Compared with 2007R1, it looks like the 2008R1.5 version of i2c-bin-twi.c has a new mode 'TWI_I2C-MODE_REPEAT' which corresponds to the Repeat Start Condition described in the HRM. However, according to the HRM, at XMIT or RECV interrupt and when the data count is 0, not only is the RESTART bit supposed to be set, but MDIR must also be set if the next operation is a receive sequence, and cleared if not. Currently there is no code that looks at the I2C_M_RD bit in the flag from the next cur_msg and set/clear the MDIR flag accordingly at the same time that the RSTART bit is set. Instead, MDIR is set or cleared (by OR'ing with 0?) after the RESTART bit has been cleared during handling of MCOMP interrupt. It appears that this is causing our failure with reading the RTC, as a quick patch to set/clear MDIR when RESTART is set seem to solve our problem. Signed-off-by: Frank Shew <fshew@geometrics.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bryan Wu <cooloney@kernel.org> [ben-linux@fluff.org: shorted subject] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-13i2c: Blackfin TWI: fix REPEAT START mode doesn't repeatSonic Zhang1-8/+7
Avoid rewrite TWI MASTER_CTL reg when issue next message In i2c repeat transfer mode, byte count of next message should be filled into part of the TWI MASTER_CTL reg when interrupt MCOMP of last message transfer is triggered. But, other bits in this reg should not be touched. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bryan Wu <cooloney@kernel.org> [ben-linux@fluff.org: shorted subject] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-13i2c: Blackfin TWI: make sure we don't end up with a CLKDIV=0Michael Hennerich2-4/+9
Make sure we don't end up with an invalid CLKDIV=0 in case someone specifies 20kHz SCL or less (5 * 1024 / 20 = 0x100). Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bryan Wu <cooloney@kernel.org> [ben-linux@fluff.org: shortened subject line] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-28 02:48:35 +0000