summaryrefslogtreecommitdiffstats
path: root/drivers/i2c/busses/i2c-i801.c
AgeCommit message (Collapse)AuthorFilesLines
2017-10-05i2c: i801: Add support for Intel Cedar ForkJarkko Nikula1-0/+4
Add PCI ID for Intel Cedar Fork PCH. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-08-28i2c: i801: Restore the presence state of P2SB PCI device after reading BARQiuxu Zhuo1-4/+8
Sun, Yunying reported the following failure on Denverton micro-server: EDAC DEBUG: pnd2_init: EDAC DEBUG: pnd2_probe: EDAC DEBUG: dnv_rd_reg: Read b_cr_tolud_pci=00000000_80000000 EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_lo_pci=00000000_80000000 EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_hi_pci=00000000_00000004 EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region0_mchbar=00000000_00000000 EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region1_mchbar=00000000_00000000 EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_base_mchbar=00000000_00000000 EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_mask_mchbar=00000000_00000000 EDAC pnd2: Failed to register device with error -19. On Denverton micro-server, the presence of the P2SB bridge PCI device is enabled or disabled by the item 'RelaxSecConf' in BIOS setup menu. When 'RelaxSecConf' is enabled, the P2SB PCI device is present and the pnd2_edac EDAC driver also uses it to get BAR. Hiding the P2SB PCI device caused the pnd2_edac EDAC driver failed to get BAR then reported the above failure. Therefor, store the presence state of P2SB PCI device before unhiding it for reading BAR and restore the presence state after reading BAR. Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com> Reported-by: Yunying Sun <yunying.sun@intel.com> Tested-by: Yunying Sun <yunying.sun@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-06-19i2c: i801: Add support for Intel Cannon LakeSrinivas Pandruvada1-0/+8
Added SMBUS PCI Ids for SMBUS for Cannon Lake PCH. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> [jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig. Cover Cannon Lake-H too] Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-02-09i2c: i801: Add support for Intel Gemini LakeMika Westerberg1-0/+3
Intel Gemini Lake has the same SMBus host controller than Intel Broxton. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24i2c: use an IRQ to report Host Notify events, not alertBenjamin Tissoires1-25/+7
The current SMBus Host Notify implementation relies on .alert() to relay its notifications. However, the use cases where SMBus Host Notify is needed currently is to signal data ready on touchpads. This is closer to an IRQ than a custom API through .alert(). Given that the 2 touchpad manufacturers (Synaptics and Elan) that use SMBus Host Notify don't put any data in the SMBus payload, the concept actually matches one to one. Benefits are multiple: - simpler code and API: the client will just have an IRQ, and nothing needs to be added in the adapter beside internally enabling it. - no more specific workqueue, the threading is handled by IRQ core directly (when required) - no more races when removing the device (the drivers are already required to disable irq on remove) - simpler handling for drivers: use plain regular IRQs - no more dependency on i2c-smbus for i2c-i801 (and any other adapter) - the IRQ domain is created automatically when the adapter exports the Host Notify capability - the IRQ are assign only if ACPI, OF and the caller did not assign one already - the domain is automatically destroyed on remove - fewer lines of code (minus 20, yeah!) Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24i2c: i801: remove SMBNTFDDAT reads as they always seem to return 0Benjamin Tissoires1-4/+6
On the platform tested, reading SMBNTFDDAT always returns 0 (using 1 read of a word or 2 of 2 bytes). Given that we are not sure why and that we don't need to rely on the data parameter in the current users of Host Notify, remove this part of the code. If someone wants to re-enable it, just revert this commit and data should be available. Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24i2c: i801: use the BIT() macro for FEATURES_* alsoBenjamin Tissoires1-8/+8
no functional changes Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24i2c: i801: use BIT() macro for bits definitionBenjamin Tissoires1-26/+26
i801 mixes hexadecimal and decimal values for defining bits. However, we have a nice BIT() macro for this exact purpose. No functional changes, cleanup only. Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24i2c: i801: minor formatting issuesBenjamin Tissoires1-4/+2
No functional changes, just typos and remove unused #define. Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24i2c: i801: store and restore the SLVCMD register at load and unloadBenjamin Tissoires1-1/+16
Also do not override any other configuration in this register. Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-25i2c: i801: Fix I2C Block Read on 8-Series/C220 and laterJean Delvare1-3/+13
Starting with the 8-Series/C220 PCH (Lynx Point), the SMBus controller includes a SPD EEPROM protection mechanism. Once the SPD Write Disable bit is set, only reads are allowed to slave addresses 0x50-0x57. However the legacy implementation of I2C Block Read since the ICH5 looks like a write, and is therefore blocked by the SPD protection mechanism. This causes the eeprom and at24 drivers to fail. So assume that I2C Block Read is implemented as an actual read on these chipsets. I tested it on my Q87 chipset and it seems to work just fine. Signed-off-by: Jean Delvare <jdelvare@suse.de> Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> [wsa: rebased to v4.9-rc2] Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-07Merge branch 'i2c/for-4.9' of ↵Linus Torvalds1-1/+4
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: "Here is the 4.9 pull request from I2C including: - centralized error messages when registering to the core - improved lockdep annotations to prevent false positives - DT support for muxes, gates, and arbitrators - bus speeds can now be obtained from ACPI - i2c-octeon got refactored and now supports ThunderX SoCs, too - i2c-tegra and i2c-designware got a bigger bunch of updates - a couple of standard driver fixes and improvements" * 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits) i2c: axxia: disable clks in case of failure in probe i2c: octeon: thunderx: Limit register access retries i2c: uniphier-f: fix misdetection of incomplete STOP condition gpio: pca953x: variable 'id' was used twice i2c: i801: Add support for Kaby Lake PCH-H gpio: pca953x: fix an incorrect lockdep warning i2c: add a warning to i2c_adapter_depth() lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible i2c: export i2c_adapter_depth() i2c: rk3x: Fix variable 'min_total_ns' unused warning i2c: rk3x: Fix sparse warning i2c / ACPI: Do not touch an I2C device if it belongs to another adapter i2c: octeon: Fix high-level controller status check i2c: octeon: Avoid sending STOP during recovery i2c: octeon: Fix set SCL recovery function i2c: rcar: add support for r8a7796 (R-Car M3-W) i2c: imx: make bus recovery through pinctrl optional i2c: meson: add gxbb compatible string i2c: uniphier-f: set the adapter to master mode when probing i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path ...
2016-09-28i2c: i801: Do not create iTCO watchdog when WDAT table existsMika Westerberg1-1/+3
ACPI WDAT table is the preferred way to use hardware watchdog over the native iTCO_wdt. Windows only uses this table for its hardware watchdog implementation so we should be relatively safe to trust it has been validated by OEMs Prevent iTCO watchdog creation if we detect that there is ACPI WDAT table. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-09-24i2c: i801: Add support for Kaby Lake PCH-HAndy Shevchenko1-0/+4
Intel Kaby Lake PCH-H has the same legacy SMBus host controller than Intel Sunrisepoint PCH. It also has same iTCO watchdog on the bus. Add Kaby Lake PCH-H PCI ID to the list of supported devices. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-08-22i2c: don't print error when adding adapter failsWolfram Sang1-1/+0
The core will do this for us now. Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Peter Korsgaard <peter@korsgaard.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Ray Jui <ray.jui@broadcom.com> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-07-26i2c: i801: use IS_ENABLED() instead of checking for built-in or moduleJavier Martinez Canillas1-6/+3
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either built-in or as a module, use that macro instead of open coding the same. Using the macro makes the code more readable by helping abstract away some of the Kconfig built-in and module enable details. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-07-06i2c: i801: add support of Host NotifyBenjamin Tissoires1-3/+85
The i801 chip can handle the Host Notify feature since ICH 3 as mentioned in http://www.intel.com/content/dam/doc/datasheet/82801ca-io-controller-hub-3-datasheet.pdf Enable the functionality unconditionally and propagate the alert on each notification. With a T440s and a Synaptics touchpad that implements Host Notify, the payload data is always 0x0000, so I am not sure if the device actually sends the payload or if there is a problem regarding the implementation. Tested-by: Andrew Duggan <aduggan@synaptics.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-07-01i2c: i801: recover from hardware PEC errorsEllen Wang1-2/+51
On a CRC error while using hardware-supported PEC, an additional error bit is set in the auxiliary status register. If this bit isn't cleared, all subsequent operations will fail, essentially hanging the controller. The fix is simple: check, report, and clear the bit in i801_check_post(). Also, in case the driver starts with the hardware in that state, clear it in i801_check_pre() as well. Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com> Tested-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-06-13i2c: i801: Drop needless bit-wise ORJean Delvare1-1/+1
The interrupt handling code makes it look like several status values may be merged together before being processed, while this will never happen. Change from bit-wise OR to simple assignment to make it more obvious and avoid misunderstanding. Signed-off-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-06-09i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BARMika Westerberg1-3/+96
Many Intel systems the BIOS declares a SystemIO OpRegion below the SMBus PCI device as can be seen in ACPI DSDT table from Lenovo Yoga 900: Device (SBUS) { OperationRegion (SMBI, SystemIO, (SBAR << 0x05), 0x10) Field (SMBI, ByteAcc, NoLock, Preserve) { HSTS, 8, Offset (0x02), HCON, 8, HCOM, 8, TXSA, 8, DAT0, 8, DAT1, 8, HBDR, 8, PECR, 8, RXSA, 8, SDAT, 16 } There are also bunch of AML methods that that the BIOS can use to access these fields. Most of the systems in question AML methods accessing the SMBI OpRegion are never used. Now, because of this SMBI OpRegion many systems fail to load the SMBus driver with an error looking like one below: ACPI Warning: SystemIO range 0x0000000000003040-0x000000000000305F conflicts with OpRegion 0x0000000000003040-0x000000000000304F (\_SB.PCI0.SBUS.SMBI) (20160108/utaddress-255) ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver The reason is that this SMBI OpRegion conflicts with the PCI BAR used by the SMBus driver. It turns out that we can install a custom SystemIO address space handler for the SMBus device to intercept all accesses through that OpRegion. This allows us to share the PCI BAR with the AML code if it for some reason is using it. We do not expect that this OpRegion handler will ever be called but if it is we print a warning and prevent all access from the SMBus driver itself. Link: https://bugzilla.kernel.org/show_bug.cgi?id=110041 Reported-by: Andy Lutomirski <luto@kernel.org> Reported-by: Pali Rohár <pali.rohar@gmail.com> Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Tested-by: Pali Rohár <pali.rohar@gmail.com> Tested-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@vger.kernel.org
2016-04-12i2c: i801: Add runtime PM support with autosuspendJarkko Nikula1-6/+22
Allow runtime PM so that PM and PCI core can put the device into low-power state when idle and resume it back when needed in those platforms that support PM for i801 device. Enable also autosuspend with 1 second delay in order to not needlessly toggle power state on and off if there are multiple transactions during short time. Device is resumed at the beginning of bus access and marked idle ready for autosuspend at the end of it. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-04-12i2c: i801: Convert to struct dev_pm_ops for suspend/resumeJarkko Nikula1-13/+11
Stop using legacy PCI PM support and convert to standard dev_pm_ops. This provides more straightforward path to add runtime PM. While at it remove explicit PCI power state control and configuration space save/restore as the PCI core does it. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-03-22Merge branch 'i2c/for-next' of ↵Linus Torvalds1-4/+4
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: "Mostly usual driver updates and improvements. The changelog should give an idea. Standing out is the i2c-qup driver with lots of new capabilities and we also have now an i2c-demuxer. I'd especially like to welcome Peter Rosin as the i2c-mux maintainer. He has an interesting series for muxes in the queue and agreed to look after this part of the subsystem. Thank you, Peter, and welcome again! The octeon changes were applied pretty recently before the merge window. I am aware. They are the first (and relatively simple) patches of a larger overhaul to this driver. In case something goes wrong with them, they are easy to fix (or revert). The advantage I see is that they are out of the way, and I can concentrate on the next block of patches. I really would like to apply the overhaul in smaller batches to avoid regressions. And waiting a cycle for the introductory patches seemed too much of a delay for me" * 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits) i2c: octeon: Support I2C_M_RECV_LEN i2c: octeon: Cleanup resource allocation code i2c: octeon: Cleanup i2c-octeon driver MAINTAINERS: add Peter Rosin as i2c mux maintainer dt-bindings: i2c: Spelling s/propoerty/property/ i2c: immediately mark ourselves as registered i2c: i801: sort IDs alphabetically MAINTAINERS: Mika and me are designated reviewers for I2C DESIGNWARE i2c: octeon: Cleanup kerneldoc comments i2c: do not use internal data from driver core i2c: cadence: Fix the kernel-doc warnings i2c: imx: remove extra spaces. i2c: rcar: don't open code of_device_get_match_data() i2c: qup: Fix fifo handling after adding V2 support i2c: xiic: Implement power management i2c: piix4: Pre-shift the port number i2c: piix4: Always use the same type for port i2c: piix4: Support alternative port selection register i2c: tegra: don't open code of_device_get_match_data() i2c: riic, sh_mobile, rcar: Use ARCH_RENESAS ...
2016-03-12i2c: i801: sort IDs alphabeticallyAndy Shevchenko1-4/+4
Sort the list to have a faster search for a certain PCI ID. There is no functional change. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-02-18i2c: i801: Adding Intel Lewisburg support for iTCOAlexandra Yates1-0/+2
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog resources have been moved to reside under the i801 SMBus host controller whereas previously they were under the LPC device. This patch adds Intel lewisburg SMBus support for iTCO device. It allows to load watchdog dynamically when the hardware is present. Fixes: cdc5a3110e7c ("i2c: i801: add Intel Lewisburg device IDs") Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
2015-11-20i2c: i801: add Intel Lewisburg device IDsAlexandra Yates1-0/+6
Adding Intel codename Lewisburg platform device IDs for SMBus. Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-25i2c: add ACPI support for I2C mux portsDustin Byford1-6/+3
Although I2C mux devices are easily enumerated using ACPI (_HID/_CID or device property compatible string match), enumerating I2C client devices connected through an I2C mux needs a little extra work. This change implements a method for describing an I2C device hierarchy that includes mux devices by using an ACPI Device() for each mux channel along with an _ADR to set the channel number for the device. See Documentation/acpi/i2c-muxes.txt for a simple example. To make this work the ismt, i801, and designware pci/platform devs now share an ACPI companion with their I2C adapter dev similar to how it's done in OF. This is done on the assumption that power management functions will not be called directly on the I2C dev that is sharing the ACPI node. Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23i2c: i801: Add support for Intel BroxtonJarkko Nikula1-0/+3
This patch adds the SMBUS PCI ID of Intel Broxton. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23i2c: i801: Add support for Intel DNVMika Westerberg1-0/+4
Intel DNV SoC has the same legacy SMBus host controller than Intel Sunrisepoint PCH. It also has same iTCO watchdog on the bus. Add DNV PCI ID to the list of supported devices. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-11i2c: i801: Create iTCO device on newer Intel PCHsMika Westerberg1-1/+119
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog resources have been moved to reside under the i801 SMBus host controller whereas previously they were under the LPC device. In order to support the iTCO watchdog on newer PCHs we need to create the platform device here in the SMBus driver and pass all known resources using platform data. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-03-09i2c: i801: Use managed pcim_* PCI device initialization and reservationJarkko Nikula1-16/+9
Simplifies the code a bit and makes easier to disable PCI device on driver detach by removing the pcim_pin_device() call in the future if needed. Reason why i2c-i801.c doesn't ever call pci_disable_device() was because it made some systems to hang during power-off. See commit d6fcb3b9cf77 ("[PATCH] i2c-i801.c: don't pci_disable_device() after it was just enabled") and http://marc.info/?l=linux-kernel&m=115160053309535&w=2 Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-03-09i2c: i801: Remove pci_enable_device() call from i801_resume()Jarkko Nikula1-1/+1
Since pci_disable_device() is not called from i801_suspend() and power state is set already it means that subsequent pci_enable_device() calls do practically nothing but monotonically increase struct pci_dev enable_cnt. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-03-09i2c: i801: Use managed devm_* memory and irq allocationJarkko Nikula1-11/+6
This simplifies the error and remove paths. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-03-09i2c: i801: Remove i801_driver forward declarationJarkko Nikula1-4/+2
struct pci_driver i801_driver forward declaration is needed only for accessing the name field. Remove it and use dev_driver_string() instead. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-03-09i2c: i801: Don't break user-visible stringsJarkko Nikula1-4/+5
It makes more difficult to grep these error prints from sources if they are split to multiple source lines. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-11-12i2c: i801: Add DeviceIDs for SunrisePoint LPDevin Ryles1-0/+3
Signed-off-by: Devin Ryles <devin.ryles@intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-11-12i2c: i801: Drop useless debug messageJean Delvare1-3/+0
Don't log the host status register value in i801_isr(), it has very little value and fills up the log when debugging is enabled. Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-11-12i2c: i801: Check if interrupts are disabledJean Delvare1-0/+20
There is a control bit in the PCI configuration space which disables interrupts. If this bit is set, the driver should not try to make use of interrupts, it won't receive any. Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-11-12i2c: i801: Fallback to polling if request_irq() failsJean Delvare1-3/+3
The i2c-i801 driver can work without interrupts, so there is no reason to make a request_irq failure fatal. Instead we can simply fallback to polling. Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-11-12i2c: i801: Use wait_event_timeout to wait for interruptsJean Delvare1-3/+22
Some systems have been reported to have trouble with interrupts. Use wait_event_timeout() instead of wait_event() so we don't get stuck in that case, and log the problem. Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-11-07i2c: remove FSF addressWolfram Sang1-4/+0
We have a central copy of the GPL for that. Some addresses were already outdated. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
2014-10-16i2c: i801: Add Device IDs for Intel Sunrise Point PCHjames.d.ralston@intel.com1-0/+3
This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH. Signed-off-by: James Ralston <james.d.ralston@intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-08-19i2c: i801: Add PCI ID for Intel BraswellAlan Cox1-0/+2
The SMBus host controller is the same as used in Baytrail so add the new PCI ID to the driver's list of supported IDs. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-07-17i2c: i801: Add device ID for Intel Wildcat Point PCHJean Delvare1-0/+3
Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-07-17i2c: i801: Fix the alignment of the device tableJean Delvare1-68/+68
A long name broke the alignment, shift the columns a bit to fix it and make the table look nice again. While we're here, switch to the standard comment style to make checkpatch happy, and use tabs instead of spaces for column alignment. Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-03-13i2c: remove DEFINE_PCI_DEVICE_TABLE macroJingoo Han1-1/+1
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro is not preferred. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-03-09i2c: i801: enable Intel BayTrail SMBUSChew, Kean ho1-0/+3
Add Device ID of Intel BayTrail SMBus Controller. Signed-off-by: Chew, Kean ho <kean.ho.chew@intel.com> Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-01-29Update Jean Delvare's e-mail addressJean Delvare1-3/+2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2013-11-14i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCHJames Ralston1-0/+3
This patch adds the SMBus Device IDs for the Intel Wildcat Point-LP PCH. Signed-off-by: James Ralston <james.d.ralston@intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-08-23i2c: move OF helpers into the coreWolfram Sang1-2/+0
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows that it is much cleaner to have this in the core. This also removes a circular dependency between the helpers and the core, and so we can finally register child nodes in the core instead of doing this manually in each driver. So, fix the drivers and documentation, too. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-22 19:28:35 +0000