| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The touchpad on the cover keyboard for the Acer Switch 3 and 5 does not
work as-is under Linux. Both devices have the same usb id for the cover
keyboard.
The kernel correctly assigns the hid-rmi driver to the device using usbhid
for transport.
Any attempts of hid-rmi to talk to the device using hid_hw_output_report
fail however as usbhid does not have a working urbout due to the lack of
any out endpoints.
Looking through Wireshark usbmon recordings from the Windows Synaptics
driver for this computer running inside of QEMU shows that it should be
using SET_REPORT requests instead.
This replaces the hid_hw_output_report in hid-rmi with a
hid_hw_raw_request for this device, which is at least enough to enable
the kernel to get working multi-touch input.
Signed-off-by: Tobias Auerochs <tobi291019@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
'for-5.2/logitech', 'for-5.2/macally', 'for-5.2/picolcd', 'for-5.2/sensor' and 'for-5.2/u2fzero' into for-linus
|
|
27 MHz mouse-only receivers send an unnumbered input report with the mouse
data, add special handling for this and add the c51b product-id to the
logi_dj_receivers table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
This receiver is almost identical to the normal unifying ones except:
- it is supposed to be paired to only one device (for performance reasons)
- the mice reports have a greater ranges in their values, so they are
using a different report ID.
Tested on a G403 and a G900.
Co-authored-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
We emulate the DJ functionality through the driver.
The receiver supports "fake device arrival" which behaves
like the probing of DJ devices.
A non-unifying receiver has 2 USB interfaces, the first one generates
standard keypresses and is compatible with the USB Keyboard Boot Subclass.
The second interface sends events for the mouse and special keys such as
the consumer-page keys. Events are split this way for BIOS / Windows /
generic-hid driver compatibility. This split does not actually match with
which device the event originate from, e.g. the consumer-page key events
originate from the keyboard but are delivered on the mouse interface.
To make sure the events are actually delivered to the dj_device
representing the originating device, we pick which dj_dev to forward
a "regular" input-report to based on the report-number, rather
then based on the originating interface.
Co-authored-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
This reverts commit 74e7c6c877f620d65a8269692d089bbd066f626c.
It finally turns out the touchpad is an engineering sample and it is
not the Synaptics touchpad. Let us revert this patch otherwise it will
affect the real Synaptics touchpad.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
U2F Zero supports custom commands for blinking the LED and getting data
from the internal hardware RNG. Expose the blinking function as a LED
device, and the internal hardware RNG as an HWRNG so that it can be used
to feed the enthropy pool.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This enables the power and equals keys on the Macally ikey keyboard.
Based on the Cougar gaming keyboard HID driver, which uses the same
vendor ID.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
We have a new Dell laptop which has the synaptics I2C touchpad
(06cb:7e7e) on it. After booting up the Linux, the touchpad doesn't
work, there is no interrupt when touching the touchpad, after
disable the runtime PM, everything works well.
I also tried the quirk of I2C_HID_QUIRK_DELAY_AFTER_SLEEP, it is
better after applied this quirk, there are interrupts but data it
reports is invalid.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
hid-uclogic driver revamp, in order to support wider range of Huion
tablets, from Nikolai Kondrashov
|
|
Toshiba WT10A tablet bluetooth keyboard support from Hans de Goede
|
|
Support for Maltron L90 from William Whistler
|
|
Logitech WingMan Formula GP fix from Jarrad Whitaker
|
|
Add support for Ugee G5 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Add support for XP-Pen Deco 01 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Add support for XP-Pen Star G640 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Add support for XP-Pen Star G540 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Add support for Ugee 2150 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Add "_UCLOGIC" to Ugee tablet device ID macros so it's clear they come
with UC-Logic vendor ID.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Add support for ViewSonic PD1011 signature (display) pad, which is also
sold by Signotec under a different name.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Originally contributed by Andrey Alekseenko <al42and@gmail.com>.
Signed-off-by: Andrey Alekseenko <al42and@gmail.com>
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
The Logitech WingMan Formula GP by default presents a combined
accelerate/brake axis, so this patch assigns it to hid-logitech in order to
benefit from the axis-splitting logic in lg4ff. There is also a fixed
report descriptor for the resulting report.
Signed-off-by: Jarrad Whitaker <jarrad.whitaker@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add support for the trackpoint and three mouse buttons on the type cover
of the Lenovo X1 Tablet Gen3.
This is the same as with the 2nd generation Lenovo X1 Tablet.
Signed-off-by: Mikael Wikström <leakim.wikstrom@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The bluetooth-keyboard which comes with the Toshiba WT10A tablet uses
a couple of usage codes in the vendor specific ffbc page.
The keyboard has a vendor-id of 04f2 which maps to Chicony.
Other then adding a few keymappings for the ffbc usages, no special
handling is necessary. So rather then adding a new hid-toshiba driver,
this commit adds the ID and 2 extra key-mappings to the hid-topseed
driver. The hid-topseed driver already contains mapping for some
ffbc usages (and does nothing else) and it already binds to another
Chicony manufactured keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
The USB report descriptor sent by the Maltron L90 keyboard is invalid,
causing the media key reports not to be accepted.
This patch adds a driver which uses a report fixup to replace the
descriptor.
Signed-off-by: William Whistler <wtbw@wtbw.co.uk>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
A Goodix touchpad doesn't work. Touching the touchpad can trigger IRQ
but there's no input event from HID subsystem.
Turns out it reports some invalid data:
[ 22.136630] i2c_hid i2c-DELL091F:00: input: 0b 00 01 00 00 00 00 00 00 00 00
After some trial and error, it's another device that doesn't work well
with ON/SLEEP commands. Disable runtime PM to fix the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
'for-4.21/hid-asus', 'for-4.21/hid-core', 'for-4.21/hid-cougar', 'for-4.21/hidraw', 'for-4.21/highres-wheel' and 'for-4.21/ish' into for-linus
|
|
The ASUS T101HA keyboard dock generates HID events using the ASUS vendor
specific UsagePage 0xff31. In consequence, some multimedia keys such as
brightness up and down are not working with hid-generic.
This commit adds the T101HA dock into the supported device list of the
hid-asus driver. It also prevents the dock's integrated touchpad to be
bound with hid-asus given that it is already working fine with
hid-multitouch.
Signed-off-by: Aleix Roca Nonell <kernelrocks@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
SNES RetroPort and RetroPad register only 4 gamepad buttons
when they should register all 8 buttons. This is described here:
https://ask.fedoraproject.org/en/question/128102
This is happening because of:
Commit 190d7f02ce8e ("HID: input: do not increment usages when
duplicate is found")
Here, I add the quirk HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE
(created for backward compatibility with the change in 190d7f02ce8e)
for the two products.
Tested with both RetroPort and RetroPad.
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Nic Soudée <nsoudee@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
The ASUS FX503VD laptop uses an USB keyboard with several hotkeys
which use the Asus Vendor specific UsagePage.
This uses two usage-codes within the page which have not been seen
before, 0x7c for its mic-mute hotkey and 0x99 for Fn+F5 which has
a "fan" symbol as hotkey symbol on the keyb. we map this to KEY_PROG4
(PROG1-PROG3 are already used).
This commit adds the mappings for the 2 new usage codes and the USB-ids
for this keyboard to the hid-asus driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
The 258a:6a88 keyboard-dock shipped with the Prowise PT301 tablet is
likely another ITE based design. The controller die is directly bonded
to the PCB with a blob of black glue on top so there are no markings and
the 258a vendor-id used is unknown anywhere. But the keyboard has the
exact same hotkeys mapped to Fn+F1 - F10 as the other ITE8595 keyboard
I have *and* it has the same quirky behavior wrt the rfkill hotkey.
Either way as said this keyboard has the same quirk for its rfkill /
airplane mode hotkey as the ITE 8595 chip, it only sends a single release
event when pressed and released, it never sends a press event.
This commit adds the 258a:6a88 USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Add USB ID 060b:700a to the list of valid USB IDS for the
cougar hid driver.
Signed-off-by: Daniel M. Lambea <dmlambea@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for two Primax mice as well.
0x4e22 is the Dell MS111-P and 0x4d0f is the unbranded HP Portia
mouse HP 697738-001. Both were built until approx. 2014.
Those were the standard mice from those vendors and are still
around - even as new old stock.
Reference: https://github.com/sriemer/fix-linux-mouse/issues/11
Signed-off-by: Sebastian Parschauer <sparschauer@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
LG touchscreen (1fd2:8001) stops working after reboot:
[ 4.859153] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 4.936070] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 9.948224] i2c_hid i2c-SAPS2101:00: failed to reset device.
The device in question stops working after receives SLEEP, ON, SLEEP
commands in a short period. The scenario is like this:
- Once the desktop session closes, it also closed the hid device, so the
device gets runtime suspended and receives a SLEEP command.
- Before calling shutdown callback, it gets runtime resumed and received
an ON command.
- In the shutdown callback, it receives another SLEEP command.
I failed to find a reliable interval between ON/SLEEP commands that can
make it work, so let's simply disable runtime PM for the device.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Cirque Touchpad/Pointstick combo is similar to Alps devices, it requires
MT_CLS_WIN_8_DUAL to expose its pointstick as a mouse.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The Motorola/Zebra Symbol DS4308-HD is a handheld USB barcode scanner
which does not have a battery, but reports one anyway that always has
capacity 2.
Let's apply the IGNORE quirk to prevent it from being treated like a
power supply so that userspaces don't get confused that this
accessory is almost out of power and warn the user that they need to charge
their wired barcode scanner.
Reported here: https://bugs.chromium.org/p/chromium/issues/detail?id=804720
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for this one as well.
References:
https://www.spinics.net/lists/linux-usb/msg88965.html
http://linet.gr.jp/~kojima/PlamoWeb/ML/htdocs/201808/msg00019.html
Signed-off-by: Sebastian Parschauer <sparschauer@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Raydium touchpanel (2386:4B33) sometimes does not work in desktop session
although it works in display manager.
During user logging, the display manager exits, close the HID device,
then the device gets runtime suspended and powered off. The desktop
session begins shortly after, opens the HID device, then the device gets
runtime resumed and powered on.
If the trasition from display manager to desktop sesesion is fast, the
touchpanel cannot switch from powered off to powered on in short
timeframe. So add a small delay to workaround the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Rumble support for Xbox One S
|
|
Driver for BigBen Interactive PS3OFMINIPAD
|
|
Support for Apple Magic Trackpad 2
|
|
Redragon Seymur 2 stops working since commit 190d7f02ce8e ("HID: input:
do not increment usages when a duplicate is found").
Use quirk HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE suggested by the commit
can solve the issue.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200995
BugLink: https://bugs.launchpad.net/bugs/1793846
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
USB device
Vendor 05ac (Apple)
Device 0265 (Magic Trackpad 2)
Bluetooth device
Vendor 004c (Apple)
Device 0265 (Magic Trackpad 2)
Add support for Apple Magic Trackpad 2 over USB and bluetooth, putting
the device in multi-touch mode.
Signed-off-by: Claudio Mettler <claudio@ponyfleisch.ch>
Signed-off-by: Marek Wyborski <marek.wyborski@emwesoft.com>
Signed-off-by: Sean O'Brien <seobrien@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This is a driver to fix input mapping and add LED & force feedback
support for the "BigBen Interactive Kid-friendly Wired Controller
PS3OFMINIPAD SONY" gamepad with USB id 146b:0902. It was originally
sold as a PS3 accessory and makes a very nice gamepad for Retropie.
Signed-off-by: Hanno Zulla <kontakt@hanno.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit 52cf93e63ee6 ("HID: i2c-hid: Don't reset device upon system resume")
removes the need for the RESEND_REPORT_DESCR quirk for Raydium devices, but
kept it for the SIS device id 10FB touchscreens, as the author of that
commit could not determine if the quirk is still necessary there.
I've tested suspend/resume on a Toshiba Click Mini L9W-B which is the
device for which this quirk was added in the first place and with the
"Don't reset device upon system resume" fix the quirk is no longer
necessary, so this commit removes it.
Note even better I also had some other devices with SIS touchscreens which
suspend/resume issues, where the RESEND_REPORT_DESCR quirk did not help.
I've also tested these devices with the "Don't reset device upon system
resume" fix and I'm happy to report that that fix also fixes touchscreen
resume on the following devices:
Asus T100HA
Asus T200TA
Peaq C1010
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Raydium touchscreen triggers interrupt storm after system-wide suspend:
[ 179.085033] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/65535)
According to Raydium, Windows driver does not reset the device after system
resume.
The HID over I2C spec does specify a reset should be used at intialization, but
it doesn't specify if reset is required for system suspend.
Tested this patch on other i2c-hid touchpanels I have and those touchpanels do
work after S3 without doing reset. If any regression happens to other
touchpanel vendors, we can use quirk for Raydium devices.
There's still one device uses I2C_HID_QUIRK_RESEND_REPORT_DESCR so keep it
there.
Cc: Aaron Ma <aaron.ma@canonical.com>
Cc: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add HID quirk driver for Xbox One S controller over bluetooth.
This driver only adds support for rumble. Standard controller
functionality is exposed by default HID driver.
[jkosina@suse.cz: straightforward rebase on more recent driver code]
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>
Signed-off-by: Juha Kuikka <juha.kuikka@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Harry Mallon <hjmallon@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
USB device
Vendor 05ac (Apple)
Device 026c (Magic Keyboard with Numeric Keypad)
Bluetooth devices
Vendor 004c (Apple)
Device 0267 (Magic Keyboard)
Device 026c (Magic Keyboard with Numeric Keypad)
Support already exists for the Magic Keyboard over USB connection.
Add support for the Magic Keyboard over Bluetooth connection, and for
the Magic Keyboard with Numeric Keypad over Bluetooth and USB
connection.
Signed-off-by: Sean O'Brien <seobrien@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The incomplete report flooded after S3 and touchscreen becomes
malfunctioned.
[ 1367.646244] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/18785)
[ 1367.649471] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/28743)
[ 1367.651092] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/26757)
[ 1367.652658] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/52280)
[ 1367.654287] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/56059)
Adding device ID, 04F3:30CC, to the quirk to re-send report description
after resume.
Cc: stable@vger.kernel.org
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
