| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add definition of the AUO B133HAN05.4 13.3" FHD panel and the
B140HAN06.4 14.0" FHD panel.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210726173300.432039-2-bjorn.andersson@linaro.org
|
|
SoCs like the rk3288 and rk3399 have 3 mipi dphys on them. One is TX-
only, one is RX-only and one can be configured to do either TX or RX.
The RX phy is statically connected to the first Image Signal Processor,
the TX phy is statically connected to the first DSI controller and
the TXRX phy is connected to both the second DSI controller as well
as the second ISP.
The RX dphy is controlled externally through registers in the "General
Register Files", while the other two are controlled through the
"Configuration and Test Interface" inside their DSI controller's
io-memory area.
The Rockchip dw-dsi controller already controls these dphys for the
TX case in the driver, but when we want to also allow configuration
for RX to the ISP from the media subsystem we need to expose phy-
functionality instead.
So add a bit of infrastructure to allow the dsi driver to work as a
phy and make sure it can be only one or the other at a time.
Similarly as the dsi-controller will be part of the drm-graph when
active, add an empty component to the drm-graph when in phy-mode
to make the rest of the drm-graph not wait for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Tested-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Acked-by: Helen Koike <helen.koike@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210210111020.2476369-4-heiko@sntech.de
|
|
In a followup patch, we'll need to access the pclk ourself to enable some
functionality, so get and store it in the rockchip dw-dsi variant as well.
Clocks are refcounted, so possible cascading enablements are
no problem.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Tested-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Acked-by: Helen Koike <helen.koike@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210210111020.2476369-2-heiko@sntech.de
|
|
As nwl_dsi.lanes is u32, and NSEC_PER_SEC is 1000000000L, the second
multiplication in
dsi->lanes * 8 * NSEC_PER_SEC
will overflow on a 32-bit platform. Fix this by making the constant
unsigned long long, forcing 64-bit arithmetic.
As iMX8 is arm64, this driver is currently used on 64-bit platforms
only, where long is 64-bit, so this cannot happen. But the issue will
start to happen when the driver is reused for a 32-bit SoC (e.g.
i.MX7ULP), or when code is copied for a new driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ebb82941a86b4e35c4fcfb1ef5a5cfad7c1fceab.1626255956.git.geert+renesas@glider.be
|
|
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
v3:
* return error if (ret < 0) (Geert)
* remove duplicate error message (Geert)
v2:
* handle errors in platform_get_irq() (Geert, Sergei)
* store IRQ number in struct shmob_drm_device (Laurent)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720080941.23646-1-tzimmermann@suse.de
|
|
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-8-tzimmermann@suse.de
|
|
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-7-tzimmermann@suse.de
|
|
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-6-tzimmermann@suse.de
|
|
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-5-tzimmermann@suse.de
|
|
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
There's one left-over reference to the imported attachment that we
keep. GEM BOs with imported attachment are considered uncached and
enables special handling within the drm_fb_swab().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-4-tzimmermann@suse.de
|
|
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-3-tzimmermann@suse.de
|
|
Implement helpers drm_gem_fb_begin_cpu_access() and _end_cpu_access(),
which call the rsp dma-buf functions for all GEM BOs of the given
framebuffer.
Calls to dma_buf_end_cpu_access() can return an error code on failure,
while drm_gem_fb_end_cpu_access() does not. The latter runs during DRM's
atomic commit or during cleanup. Both cases don't allow for errors, so
leave out the return value.
v2:
* fix typo in docs (Daniel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-2-tzimmermann@suse.de
|
|
The variable 'priv' got introduced in commit 39a364a19e03
("drm/hisilicon/hibmc: Convert to Linux IRQ interfaces") by accident.
It's unused; remove it. Fixes a compiler warning.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 39a364a19e03 ("drm/hisilicon/hibmc: Convert to Linux IRQ interfaces")
Reviewed-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: Dave Airlie <airlied@gmail.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Tian Tao <tiantao6@hisilicon.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721131704.10306-1-tzimmermann@suse.de
|
|
Set a condition for the message of "Couldn't set OPP regulators" to not
display if the error code is EPROBE_DEFER. Note that I used an if
statement to capture the condition instead of the dev_err_probe
function because I didn't want to change the DRM_DEV_ERROR usage.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721214830.25690-1-macroalpha82@gmail.com
|
|
The register_gop_device() function registers an "efi-framebuffer" platform
device to match against the efifb driver, to have an early framebuffer for
EFI platforms.
But there is already support to do exactly the same by the Generic System
Framebuffers (sysfb) driver. This used to be only for X86 but it has been
moved to drivers/firmware and could be reused by other architectures.
Also, besides supporting registering an "efi-framebuffer", this driver can
register a "simple-framebuffer" allowing to use the siple{fb,drm} drivers
on non-X86 EFI platforms. For example, on aarch64 these drivers can only
be used with DT and doesn't have code to register a "simple-frambuffer"
platform device when booting with EFI.
For these reasons, let's remove the register_gop_device() duplicated code
and instead move the platform specific logic that's there to sysfb driver.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210625131359.1804394-1-javierm@redhat.com
|
|
The VGA arbitration is entirely based on pci_dev structures, so just pass
that back to the set_vga_decode callback.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716061634.2446357-8-hch@lst.de
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
All callers pass NULL as the irq_set_state argument, so remove it and
the ->irq_set_state member in struct vga_device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716061634.2446357-7-hch@lst.de
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
Add a trivial wrapper for the unregister case that sets all fields to
NULL.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716061634.2446357-6-hch@lst.de
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
Kerneldoc comments should be at the implementation side, not in the
header just declaring the prototype.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716061634.2446357-4-hch@lst.de
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
vga_conflicts only has a single caller and none of the arch overrides
mentioned in the comment. Just remove it and the thus dead check in the
caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716061634.2446357-3-hch@lst.de
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
The V3D engine has several hardware performance counters that can of
interest for userspace performance analysis tools.
This exposes new ioctls to create and destroy performance monitor
objects, as well as to query the counter values.
Each created performance monitor object has an ID that can be attached
to CL/CSD submissions, so the driver enables the requested counters when
the job is submitted, and updates the performance monitor values when
the job is done.
It is up to the user to ensure all the jobs have been finished before
getting the performance monitor values. It is also up to the user to
properly synchronize BCL jobs when submitting jobs with different
performance monitors attached.
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Emma Anholt <emma@anholt.net>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Juan A. Suarez Romero <jasuarez@igalia.com>
Acked-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210608111541.461991-1-jasuarez@igalia.com
|
|
drm_file->master pointers should be protected by
drm_device.master_mutex or drm_file.master_lookup_lock when being
dereferenced.
However, in drm_lease.c, there are multiple instances where
drm_file->master is accessed and dereferenced while neither lock is
held. This makes drm_lease.c vulnerable to use-after-free bugs.
We address this issue in 2 ways:
1. Add a new drm_file_get_master() function that calls drm_master_get
on drm_file->master while holding on to
drm_file.master_lookup_lock. Since drm_master_get increments the
reference count of master, this prevents master from being freed until
we unreference it with drm_master_put.
2. In each case where drm_file->master is directly accessed and
eventually dereferenced in drm_lease.c, we wrap the access in a call
to the new drm_file_get_master function, then unreference the master
pointer once we are done using it.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-6-desmondcheongzx@gmail.com
|
|
Currently, drm_file.master pointers should be protected by
drm_device.master_mutex when being dereferenced. This is because
drm_file.master is not invariant for the lifetime of drm_file. If
drm_file is not the creator of master, then drm_file.is_master is
false, and a call to drm_setmaster_ioctl will invoke
drm_new_set_master, which then allocates a new master for drm_file and
puts the old master.
Thus, without holding drm_device.master_mutex, the old value of
drm_file.master could be freed while it is being used by another
concurrent process.
However, it is not always possible to lock drm_device.master_mutex to
dereference drm_file.master. Through the fbdev emulation code, this
might occur in a deep nest of other locks. But drm_device.master_mutex
is also the outermost lock in the nesting hierarchy, so this leads to
potential deadlocks.
To address this, we introduce a new spin lock at the bottom of the
lock hierarchy that only serializes drm_file.master. With this change,
the value of drm_file.master changes only when both
drm_device.master_mutex and drm_file.master_lookup_lock are
held. Hence, any process holding either of those locks can ensure that
the value of drm_file.master will not change concurrently.
Since no lock depends on the new drm_file.master_lookup_lock, when
drm_file.master is dereferenced, but drm_device.master_mutex cannot be
held, we can safely protect the master pointer with
drm_file.master_lookup_lock.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-5-desmondcheongzx@gmail.com
|
|
While checking the master status of the DRM file in
drm_is_current_master(), the device's master mutex should be
held. Without the mutex, the pointer fpriv->master may be freed
concurrently by another process calling drm_setmaster_ioctl(). This
could lead to use-after-free errors when the pointer is subsequently
dereferenced in drm_lease_owner().
The callers of drm_is_current_master() from drm_auth.c hold the
device's master mutex, but external callers do not. Hence, we implement
drm_is_current_master_locked() to be used within drm_auth.c, and
modify drm_is_current_master() to grab the device's master mutex
before checking the master status.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-4-desmondcheongzx@gmail.com
|
|
Inside drm_clients_info, the rcu_read_lock is held to lock
pid_task()->comm. However, within this protected section, a call to
drm_is_current_master is made, which involves a mutex lock in a future
patch. However, this is illegal because the mutex lock might block
while in the RCU read-side critical section.
Since drm_is_current_master isn't protected by rcu_read_lock, we avoid
this by moving it out of the RCU critical section.
The following report came from intel-gfx ci's
igt@debugfs_test@read_all_entries testcase:
=============================
[ BUG: Invalid wait context ]
5.13.0-CI-Patchwork_20515+ #1 Tainted: G W
-----------------------------
debugfs_test/1101 is trying to lock:
ffff888132d901a8 (&dev->master_mutex){+.+.}-{3:3}, at:
drm_is_current_master+0x1e/0x50
other info that might help us debug this:
context-{4:4}
3 locks held by debugfs_test/1101:
#0: ffff88810fdffc90 (&p->lock){+.+.}-{3:3}, at:
seq_read_iter+0x53/0x3b0
#1: ffff888132d90240 (&dev->filelist_mutex){+.+.}-{3:3}, at:
drm_clients_info+0x63/0x2a0
#2: ffffffff82734220 (rcu_read_lock){....}-{1:2}, at:
drm_clients_info+0x1b1/0x2a0
stack backtrace:
CPU: 8 PID: 1101 Comm: debugfs_test Tainted: G W
5.13.0-CI-Patchwork_20515+ #1
Hardware name: Intel Corporation CometLake Client Platform/CometLake S
UDIMM (ERB/CRB), BIOS CMLSFWR1.R00.1263.D00.1906260926 06/26/2019
Call Trace:
dump_stack+0x7f/0xad
__lock_acquire.cold.78+0x2af/0x2ca
lock_acquire+0xd3/0x300
? drm_is_current_master+0x1e/0x50
? __mutex_lock+0x76/0x970
? lockdep_hardirqs_on+0xbf/0x130
__mutex_lock+0xab/0x970
? drm_is_current_master+0x1e/0x50
? drm_is_current_master+0x1e/0x50
? drm_is_current_master+0x1e/0x50
drm_is_current_master+0x1e/0x50
drm_clients_info+0x107/0x2a0
seq_read_iter+0x178/0x3b0
seq_read+0x104/0x150
full_proxy_read+0x4e/0x80
vfs_read+0xa5/0x1b0
ksys_read+0x5a/0xd0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-3-desmondcheongzx@gmail.com
|
|
In preparation for a future patch to take a lock on
drm_device.master_mutex inside drm_is_current_master(), we first move
the call to drm_is_current_master() in drm_mode_getconnector out from the
section locked by &dev->mode_config.mutex. This avoids creating a
circular lock dependency.
Failing to avoid this lock dependency produces the following lockdep
splat:
======================================================
WARNING: possible circular locking dependency detected
5.13.0-rc7-CI-CI_DRM_10254+ #1 Not tainted
------------------------------------------------------
kms_frontbuffer/1087 is trying to acquire lock:
ffff88810dcd01a8 (&dev->master_mutex){+.+.}-{3:3}, at: drm_is_current_master+0x1b/0x40
but task is already holding lock:
ffff88810dcd0488 (&dev->mode_config.mutex){+.+.}-{3:3}, at: drm_mode_getconnector+0x1c6/0x4a0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&dev->mode_config.mutex){+.+.}-{3:3}:
__mutex_lock+0xab/0x970
drm_client_modeset_probe+0x22e/0xca0
__drm_fb_helper_initial_config_and_unlock+0x42/0x540
intel_fbdev_initial_config+0xf/0x20 [i915]
async_run_entry_fn+0x28/0x130
process_one_work+0x26d/0x5c0
worker_thread+0x37/0x380
kthread+0x144/0x170
ret_from_fork+0x1f/0x30
-> #1 (&client->modeset_mutex){+.+.}-{3:3}:
__mutex_lock+0xab/0x970
drm_client_modeset_commit_locked+0x1c/0x180
drm_client_modeset_commit+0x1c/0x40
__drm_fb_helper_restore_fbdev_mode_unlocked+0x88/0xb0
drm_fb_helper_set_par+0x34/0x40
intel_fbdev_set_par+0x11/0x40 [i915]
fbcon_init+0x270/0x4f0
visual_init+0xc6/0x130
do_bind_con_driver+0x1e5/0x2d0
do_take_over_console+0x10e/0x180
do_fbcon_takeover+0x53/0xb0
register_framebuffer+0x22d/0x310
__drm_fb_helper_initial_config_and_unlock+0x36c/0x540
intel_fbdev_initial_config+0xf/0x20 [i915]
async_run_entry_fn+0x28/0x130
process_one_work+0x26d/0x5c0
worker_thread+0x37/0x380
kthread+0x144/0x170
ret_from_fork+0x1f/0x30
-> #0 (&dev->master_mutex){+.+.}-{3:3}:
__lock_acquire+0x151e/0x2590
lock_acquire+0xd1/0x3d0
__mutex_lock+0xab/0x970
drm_is_current_master+0x1b/0x40
drm_mode_getconnector+0x37e/0x4a0
drm_ioctl_kernel+0xa8/0xf0
drm_ioctl+0x1e8/0x390
__x64_sys_ioctl+0x6a/0xa0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of: &dev->master_mutex --> &client->modeset_mutex --> &dev->mode_config.mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->mode_config.mutex);
lock(&client->modeset_mutex);
lock(&dev->mode_config.mutex);
lock(&dev->master_mutex);
*** DEADLOCK ***
1 lock held by kms_frontbuffer/1087:
#0: ffff88810dcd0488 (&dev->mode_config.mutex){+.+.}-{3:3}, at: drm_mode_getconnector+0x1c6/0x4a0
stack backtrace:
CPU: 7 PID: 1087 Comm: kms_frontbuffer Not tainted 5.13.0-rc7-CI-CI_DRM_10254+ #1
Hardware name: Intel Corporation Ice Lake Client Platform/IceLake U DDR4 SODIMM PD RVP TLC, BIOS ICLSFWR1.R00.3234.A01.1906141750 06/14/2019
Call Trace:
dump_stack+0x7f/0xad
check_noncircular+0x12e/0x150
__lock_acquire+0x151e/0x2590
lock_acquire+0xd1/0x3d0
__mutex_lock+0xab/0x970
drm_is_current_master+0x1b/0x40
drm_mode_getconnector+0x37e/0x4a0
drm_ioctl_kernel+0xa8/0xf0
drm_ioctl+0x1e8/0x390
__x64_sys_ioctl+0x6a/0xa0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-2-desmondcheongzx@gmail.com
|
|
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() will be called in release automatically.
v3:
reformat commit message
update for move to tiny/
v2:
use pcim_enable_device()
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715132845.2415619-1-yangyingliang@huawei.com
|
|
[Bug][AST2500]
V1:
When AST2500 acts as stand-alone VGA so that DRAM and DVO initialization
have to be achieved by VGA driver with P2A (PCI to AHB) enabling.
However, HW suggests disable Fast reset mode after DRAM initializaton,
because fast reset mode is mainly designed for ARM ICE debugger.
Once Fast reset is checked as enabling, WDT (Watch Dog Timer) should be
first enabled to avoid system deadlock before disable fast reset mode.
V2:
Use to_pci_dev() to get revision of PCI configuration.
V3:
If SCU00 is not unlocked, just enter its password again.
It is unnecessary to clear AHB lock condition and restore WDT default
setting again, before Fast-reset clearing.
V4:
repatch after "error : could not build fake ancestor" resolved.
V5:
Since CVE_2019_6260 item3, Most of AST2500 have disabled P2A(PCIe to AMBA).
However, for backward compatibility, some patches about P2A, such as items
of v5.2 and v5.3, are considered to be upstreamed with comments.
1. Add define macro to improve source readability.
ast_drv.h, ast_main.c, ast_post.c
2. Add comment about "Fast restet" is enabled for ARM-ICE debugger
ast_post.c
3. Add comment about Reset USB port to patch USB unknown device issue
ast_post.c
Signed-off-by: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210709080900.4056-1-kuohsiang_chou@aspeedtech.com
|
|
The function ast_get_modes() will also return 0, when it try to get the
edid, but it also do not get the edid.
Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716015615.9150-1-ainux.wang@gmail.com
|
|
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
This patch also fixes a bug where the driver didn't release the
IRQ.
v2:
* automatically release IRQ via devm_request_irq() (Paul)
* mention the bugfix (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715100258.6638-1-tzimmermann@suse.de
|
|
The driver uses a conservative set of hardcoded values for the
maximum time delay of the transitions between LP and HS, either
for data and clock lanes.
By using the info in STM32MP157 datasheet, valid also for other ST
devices, compute the actual delay from the lane's bps.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@foss.st.com>
Acked-by: Philippe Cornu <philippe.cornu@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210713144941.3599-1-antonio.borneo@foss.st.com
|
|
As dw-mipi-dsi supported all possible ways to find the DSI
devices. It can take multiple iterations for ltdc to find
all components attached to the DSI bridge.
The current ltdc driver failed to find the endpoint as
it returned -EINVAL for the first iteration itself. This leads
to following error:
[ 3.099289] [drm:ltdc_load] *ERROR* init encoder endpoint 0
So, check the return value and cleanup the encoder only if it's
not -EPROBE_DEFER. This make all components in the attached DSI
bridge found properly.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Acked-by: Philippe Cornu <philippe.cornu@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210704135914.268308-1-jagan@amarulasolutions.com
|
|
This adds a driver for panels based on the WideChips WS2401 display
controller. This display controller is used in the Samsung LMS380KF01
display found in the Samsung GT-I8160 (Codina) mobile phone and
possibly others.
As is common with Samsung displays manufacturer commands are necessary
to configure the display to a working state.
The display optionally supports internal backlight control, but can
also use an external backlight.
This driver re-uses the DBI infrastructure to communicate with the
display.
Cc: phone-devel@vger.kernel.org
Cc: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714225002.1065107-2-linus.walleij@linaro.org
|
|
Even after the DP AUX backlight on my board worked OK after applying
the patch ("drm/panel-simple: Power the panel when probing DP AUX
backlight") [1], I still noticed some strange timeouts being reported
by ti_sn_aux_transfer(). Digging, I realized the problem was this:
* Even though `enabled` in `struct dp_aux_backlight` was false, the
base backlight structure (`base` in that structure) thought that the
backlight was powered on.
* If userspace wrote to sysfs in this state then we'd try to enable
the backlight.
* Unfortunatley, enabling the backlight didn't work because the panel
itself wasn't powered.
We can only use the backlight if the panel is on and the panel is not
officially on when we probe (it's temporarily just on enough for us to
talk to it).
The important thing we want here is to get `BL_CORE_FBBLANK` set since
userspace can't mess with that. This will keep us disabled until
drm_panel enables us, which means that the panel is enabled
first. Ideally we'd just set this in our `props` before calling
devm_backlight_device_register() but the comments in the header file
are pretty explicit that we're not supposed to much with the `state`
ourselves. Because of this, there may be a small window where the
backlight device is registered and someone could try to tweak with the
backlight. This isn't likely to happen and even if it did, I don't
believe this causes any huge problem.
[1] https://lore.kernel.org/lkml/20210714093334.1.Idb41f87e5abae4aee0705db7458b0097fc50e7ab@changeid/
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714101744.1.Ifc22696b27930749915e383f0108b7bcdc015a6e@changeid
|
|
When I tried booting up a device that needed the DP AUX backlight, I
found an error in the logs:
panel-simple-dp-aux: probe of aux-ti_sn65dsi86.aux.0 failed with error -110
The aux transfers were failing because the panel wasn't powered. Just
like when reading the EDID we need to power the panel when trying to
talk to it. Add the needed pm_runtime calls.
After I do this I can successfully probe the panel and adjust the
backlight on my board.
Fixes: bfd451403d70 ("drm/panel-simple: Support DP AUX backlight")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714093334.1.Idb41f87e5abae4aee0705db7458b0097fc50e7ab@changeid
|
|
When bailing out due to the sanity check the iterator value needs to be
freed because the early return prevents for_each_child_of_node() from
doing the dereference itself.
Fixes: 6529007522de ("drm: of: Add drm_of_lvds_get_dual_link_pixel_order")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714143300.20632-1-steven.price@arm.com
|
|
The comment refers to drm_irq_install() et al, which are not used by
omapdrm. The functions are part of the DRM IRQ midlayer and shouldn't
be used any longer. Remove the comment.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210706073125.7689-1-tzimmermann@suse.de
|
|
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210706075011.9009-1-tzimmermann@suse.de
|
|
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210706074735.8849-1-tzimmermann@suse.de
|
|
The drm_encoder crtc pointer isn't really fit for an atomic driver,
let's rely on the connector state instead.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707141930.1811128-1-maxime@cerno.tech
|
|
Our hotplug handler will currently call the drm_kms_helper_hotplug_event
every time a hotplug interrupt is called.
However, since the device is registered after all the drivers have
finished their bind callback, we have a window between when we install
our interrupt handler and when drm_dev_register() is eventually called
where our handler can run and call drm_kms_helper_hotplug_event but the
device hasn't been registered yet, causing a null pointer dereference.
Fix this by making sure we only call drm_kms_helper_hotplug_event if our
device has been properly registered.
Fixes: f4790083c7c2 ("drm/vc4: hdmi: Rely on interrupts to handle hotplug")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707095112.1469670-4-maxime@cerno.tech
|
|
The hotplugs interrupt handlers are registered through the
devm_request_threaded_irq function. However, while free_irq is indeed
called properly when the device is unbound or bind fails, it's called
after unbind or bind is done.
In our particular case, it means that on failure it creates a window
where our interrupt handler can be called, but we're freeing every
resource (CEC adapter, DRM objects, etc.) it might need.
In order to address this, let's switch to the non-devm variant to
control better when the handler will be unregistered and allow us to
make it safe.
Fixes: f4790083c7c2 ("drm/vc4: hdmi: Rely on interrupts to handle hotplug")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707095112.1469670-3-maxime@cerno.tech
|
|
Add support for the Innolux/Chimei EJ030NA 3.0"
320x480 TFT panel.
This panel can be found in the LDKs, RS97 V2.1 and RG300 (non IPS)
handheld gaming consoles.
While being 320x480, it is actually a horizontal 4:3
panel with non-square pixels in delta arrangement.
Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210625121045.81711-2-paul@crapouillou.net
|
|
shmem helpers seem a bit sloppy here by automatically rounding up when
actually creating the buffer, which results in under-reporting of what
we actually have. Caught by igt/vgem_basic tests.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210603164113.1433476-4-daniel.vetter@ffwll.ch
|
|
We were getting a depmod error:
depmod: ERROR: Cycle detected: drm_kms_helper -> drm -> drm_kms_helper
It looks like the rule is that drm_kms_helper can call into drm, but
drm can't call into drm_kms_helper. That means we've got to move the
DP AUX backlight support into drm_dp_helper.
NOTE: as part of this, I didn't try to do any renames of the main
registration function. Even though it's in the drm_dp_helper, it still
feels very parallel to drm_panel_of_backlight().
Fixes: 10f7b40e4f30 ("drm/panel: add basic DP AUX backlight support")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rajeev Nandan <rajeevny@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712075933.v2.1.I23eb4cc5a680341e7b3e791632a635566fa5806a@changeid
|
|
Store the shadow-buffer mapping's address in struct vkms_composer and
use the value when composing the output. It's the same value as stored
in the GEM SHMEM BO, but frees the composer code from its dependency
on GEM SHMEM.
Using struct dma_buf_map is how framebuffer access is supposed to be.
The long-term plan is to perform all framebuffer access via struct
dma_buf_map and avoid the details of accessing I/O and system memory.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210705074633.9425-5-tzimmermann@suse.de
|
|
Replace vkms' prepare_fb and cleanup_fb functions with the generic
code for shadow-buffered planes. No functional changes.
This change also fixes a problem where IGT kms_flip tests would
create a segmentation fault within vkms. The driver's prepare_fb
function did not report an error if a BO's vmap operation failed.
The kernel later tried to operate on the non-mapped memory areas.
The shared shadow-plane helpers handle errors correctly, so that
the driver now avoids the segmantation fault.
v2:
* include paragraph about IGT tests in commit message (Melissa)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210705074633.9425-4-tzimmermann@suse.de
|
|
Subclass struct drm_shadow_plane_state for VKMS planes and update
all plane-state callbacks accordingly.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210705074633.9425-3-tzimmermann@suse.de
|
|
Export the implementation of duplicate, destroy and reset helpers for
shadow-buffered plane state. Useful for drivers that subclass struct
drm_shadow_plane_state.
The exported functions are wrappers around plane-state implementation,
but using them is the correct thing to do for drivers.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210705074633.9425-2-tzimmermann@suse.de
|
|
Commit 375cca1cfeb5 ("drm/vgem: Implement mmap as GEM object function")
broke several IGT tests in vgem_basic. [1] Attempts to fix the issue
have not worked out so far. [2][3] Revert the change for now.
Note that there is a patch that converts vgem to shmem helpers. [4]
Merging this change would be preferable to modifying vgem's mmap code.
v2:
* fix spelling error in commit message (Daniel)
[1] https://intel-gfx-ci.01.org/tree/drm-tip/igt@vgem_basic@unload.html
[2] https://lore.kernel.org/intel-gfx/20210709154256.12005-1-tzimmermann@suse.de/
[3] https://lore.kernel.org/intel-gfx/20210712123321.3658-1-tzimmermann@suse.de/
[4] https://patchwork.freedesktop.org/series/90671/
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 375cca1cfeb5 ("drm/vgem: Implement mmap as GEM object function")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Christian König <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Melissa Wen <melissa.srw@gmail.com>
Cc: Qinglang Miao <miaoqinglang@huawei.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210713090235.26372-1-tzimmermann@suse.de
|
