| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
BCM2711 DSI1 doesn't have the issue with the ARM not being
able to write to the registers, therefore remove the DMA
workaround for that compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-8-maxime@cerno.tech
|
|
DSI0 was partially supported, but didn't register with the main
driver, and the code was inconsistent as to whether it checked
port == 0 or port == 1.
Add compatible string and other support to make it consistent.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-6-maxime@cerno.tech
|
|
Most of the differences between DSI0 and DSI1 are handled through the
ID. However, the BCM2711 DSI is going to introduce one more variable to
the mix and will break some expectations of the earlier, simpler, test.
Let's add a variant structure that will address most of the differences
between those three controllers.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-5-maxime@cerno.tech
|
|
The DSI clocks setup function has been using an array to store the clock
name of either the DSI0 or DSI1 blocks, using the port ID to choose the
proper one.
Let's switch to an snprintf call to do the same thing and simplify the
array a bit.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-4-maxime@cerno.tech
|
|
The DSI1_PHY_AFEC0_PD_DLANE1 and DSI1_PHY_AFEC0_PD_DLANE3 register
definitions were swapped, so trying to use more than a single data
lane failed as lane 1 would get powered down.
(In theory a 4 lane device would work as all lanes would remain
powered).
Correct the definitions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-3-maxime@cerno.tech
|
|
That pointer isn't used anywhere, so there's no point in keeping it.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-2-maxime@cerno.tech
|
|
If the DSI driver is the last to probe, component_add will try to run all
the bind callbacks straight away and return the error code.
However, since we depend on a power domain, we're pretty much guaranteed to
be in that case on the BCM2711, and are just lucky on the previous SoCs
since the v3d also depends on that power domain and is further in the probe
order.
In that case, the DSI host will not stick around in the system: the DSI
bind callback will be executed, will not find any DSI device attached and
will return EPROBE_DEFER, and we will then remove the DSI host and ask to
be probed later on.
But since that host doesn't stick around, DSI devices like the RaspberryPi
touchscreen whose probe is not linked to the DSI host (unlike the usual DSI
devices that will be probed through the call to mipi_dsi_host_register)
cannot attach to the DSI host, and we thus end up in a situation where the
DSI host cannot probe because the panel hasn't probed yet, and the panel
cannot probe because the DSI host hasn't yet.
In order to break this cycle, let's wait until there's a DSI device that
attaches to the DSI host to register the component and allow to progress
further.
Acked-by: Eric Anholt <eric@anholt.net>
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200707101912.571531-1-maxime@cerno.tech
|
|
The vc4 driver uses empty implementations for its encoders. Replace
the code with the generic simple encoder.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305155950.2705-19-tzimmermann@suse.de
|
|
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
|
|
Commit 05193dc38197 ("drm/bridge: Make the bridge chain a double-linked
list") patched the bridge chain logic to use a double-linked list instead
of a single-linked list. This change induced changes to the VC4 driver
which was manually resetting the encoder->bridge element to NULL to
control the enable/disable sequence of the bridge chain. During this
conversion, 2 bugs were introduced:
1/ list_splice() was used to move chain elements to our own internal
chain, but list_splice() does not reset the source list to an empty
state, leading to unexpected bridge hook calls when
drm_bridge_chain_xxx() helpers were called by the core. Replacing
those list_splice() calls by list_splice_init() ones fixes this
problem.
2/ drm_bridge_chain_xxx() helpers operate on the
bridge->encoder->bridge_chain list, which is now empty. When the
helper uses list_for_each_entry_reverse() we end up with no operation
done which is not what we want. But that's even worse when the helper
uses list_for_each_entry_from(), because in that case we end up in
an infinite loop searching for the list head element which is no
longer encoder->bridge_chain but vc4_dsi->bridge_chain. To address
that problem we stop using the bridge chain helpers and call the
hooks directly.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Eric Anholt <eric@anholt.net>
Fixes: 05193dc38197 ("drm/bridge: Make the bridge chain a double-linked list")
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20191227144124.210294-2-boris.brezillon@collabora.com
|
|
So that each element in the chain can easily access its predecessor.
This will be needed to support bus format negotiation between elements
of the bridge chain.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203141515.3597631-5-boris.brezillon@collabora.com
|
|
Change the prefix of bridge helpers targeting a bridge chain from
drm_bridge_ to drm_bridge_chain_ to better reflect the fact that
the operation will happen on all elements of chain, starting at the
bridge passed in argument.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203141515.3597631-2-boris.brezillon@collabora.com
|
|
The drm panel bridge creates a connector using a connector type
explicitly passed by the display controller or bridge driver that
instantiates the panel bridge. Now that drm_panel reports its connector
type, we can use it to avoid passing an explicit (and often incorrect)
connector type to drm_panel_bridge_add() and
devm_drm_panel_bridge_add().
Several drivers report incorrect or unknown connector types to
userspace. Reporting a different type may result in a breakage. For that
reason, rename (devm_)drm_panel_bridge_add() to
(devm_)drm_panel_bridge_add_typed(), and add new
(devm_)drm_panel_bridge_add() functions that use the panel connector
type. Update all callers of (devm_)drm_panel_bridge_add() to the _typed
function, they will be converted one by one after testing.
The panel drivers have been updated with the following Coccinelle
semantic patch, with manual inspection and fixes to indentation.
@@
expression bridge;
expression dev;
expression panel;
identifier type;
@@
(
-bridge = drm_panel_bridge_add(panel, type);
+bridge = drm_panel_bridge_add_typed(panel, type);
|
-bridge = devm_drm_panel_bridge_add(dev, panel, type);
+bridge = devm_drm_panel_bridge_add_typed(dev, panel, type);
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904132804.29680-3-laurent.pinchart@ideasonboard.com
|
|
We are about to add a drm_bridge_state that inherits from
drm_private_state which is defined in drm_atomic.h. Problem is,
drm_atomic.h includes drm_crtc.h which in turn includes drm_bridge.h,
leading to "drm_private_state has incomplete type" error.
Let's force all users of the drm_bridge API to explicitly include
drm_bridge.h.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826152649.13820-2-boris.brezillon@collabora.com
|
|
Noralf needs some SPI patches in 5.3 to merge some work on tinydrm.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Drop use of the deprecated header drmP.h.
Fix so vc4_drv.h is now self-contained, and fixed fall-out in remaining
files.
Divided include files in blocks.
Sorted include files within their blocks.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190716064220.18157-7-sam@ravnborg.org
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk framework updates from Stephen Boyd:
"One more patch to remove io.h from clk-provider.h.
We used to need this include when we had clk_readl() and clk_writel(),
but those are gone now so this patch pushes the dependency out to the
users of clk-provider.h"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Remove io.h from clk-provider.h
|
|
Now that we've gotten rid of clk_readl() we can remove io.h from the
clk-provider header and push out the io.h include to any code that isn't
already including the io.h header but using things like readl/writel,
etc.
Found with this grep:
git grep -l clk-provider.h | grep '.c$' | xargs git grep -L 'linux/io.h' | \
xargs git grep -l \
-e '\<__iowrite32_copy\>' --or \
-e '\<__ioread32_copy\>' --or \
-e '\<__iowrite64_copy\>' --or \
-e '\<ioremap_page_range\>' --or \
-e '\<ioremap_huge_init\>' --or \
-e '\<arch_ioremap_pud_supported\>' --or \
-e '\<arch_ioremap_pmd_supported\>' --or \
-e '\<devm_ioport_map\>' --or \
-e '\<devm_ioport_unmap\>' --or \
-e '\<IOMEM_ERR_PTR\>' --or \
-e '\<devm_ioremap\>' --or \
-e '\<devm_ioremap_nocache\>' --or \
-e '\<devm_ioremap_wc\>' --or \
-e '\<devm_iounmap\>' --or \
-e '\<devm_ioremap_release\>' --or \
-e '\<devm_memremap\>' --or \
-e '\<devm_memunmap\>' --or \
-e '\<__devm_memremap_pages\>' --or \
-e '\<pci_remap_cfgspace\>' --or \
-e '\<arch_has_dev_port\>' --or \
-e '\<arch_phys_wc_add\>' --or \
-e '\<arch_phys_wc_del\>' --or \
-e '\<memremap\>' --or \
-e '\<memunmap\>' --or \
-e '\<arch_io_reserve_memtype_wc\>' --or \
-e '\<arch_io_free_memtype_wc\>' --or \
-e '\<__io_aw\>' --or \
-e '\<__io_pbw\>' --or \
-e '\<__io_paw\>' --or \
-e '\<__io_pbr\>' --or \
-e '\<__io_par\>' --or \
-e '\<__raw_readb\>' --or \
-e '\<__raw_readw\>' --or \
-e '\<__raw_readl\>' --or \
-e '\<__raw_readq\>' --or \
-e '\<__raw_writeb\>' --or \
-e '\<__raw_writew\>' --or \
-e '\<__raw_writel\>' --or \
-e '\<__raw_writeq\>' --or \
-e '\<readb\>' --or \
-e '\<readw\>' --or \
-e '\<readl\>' --or \
-e '\<readq\>' --or \
-e '\<writeb\>' --or \
-e '\<writew\>' --or \
-e '\<writel\>' --or \
-e '\<writeq\>' --or \
-e '\<readb_relaxed\>' --or \
-e '\<readw_relaxed\>' --or \
-e '\<readl_relaxed\>' --or \
-e '\<readq_relaxed\>' --or \
-e '\<writeb_relaxed\>' --or \
-e '\<writew_relaxed\>' --or \
-e '\<writel_relaxed\>' --or \
-e '\<writeq_relaxed\>' --or \
-e '\<readsb\>' --or \
-e '\<readsw\>' --or \
-e '\<readsl\>' --or \
-e '\<readsq\>' --or \
-e '\<writesb\>' --or \
-e '\<writesw\>' --or \
-e '\<writesl\>' --or \
-e '\<writesq\>' --or \
-e '\<inb\>' --or \
-e '\<inw\>' --or \
-e '\<inl\>' --or \
-e '\<outb\>' --or \
-e '\<outw\>' --or \
-e '\<outl\>' --or \
-e '\<inb_p\>' --or \
-e '\<inw_p\>' --or \
-e '\<inl_p\>' --or \
-e '\<outb_p\>' --or \
-e '\<outw_p\>' --or \
-e '\<outl_p\>' --or \
-e '\<insb\>' --or \
-e '\<insw\>' --or \
-e '\<insl\>' --or \
-e '\<outsb\>' --or \
-e '\<outsw\>' --or \
-e '\<outsl\>' --or \
-e '\<insb_p\>' --or \
-e '\<insw_p\>' --or \
-e '\<insl_p\>' --or \
-e '\<outsb_p\>' --or \
-e '\<outsw_p\>' --or \
-e '\<outsl_p\>' --or \
-e '\<ioread8\>' --or \
-e '\<ioread16\>' --or \
-e '\<ioread32\>' --or \
-e '\<ioread64\>' --or \
-e '\<iowrite8\>' --or \
-e '\<iowrite16\>' --or \
-e '\<iowrite32\>' --or \
-e '\<iowrite64\>' --or \
-e '\<ioread16be\>' --or \
-e '\<ioread32be\>' --or \
-e '\<ioread64be\>' --or \
-e '\<iowrite16be\>' --or \
-e '\<iowrite32be\>' --or \
-e '\<iowrite64be\>' --or \
-e '\<ioread8_rep\>' --or \
-e '\<ioread16_rep\>' --or \
-e '\<ioread32_rep\>' --or \
-e '\<ioread64_rep\>' --or \
-e '\<iowrite8_rep\>' --or \
-e '\<iowrite16_rep\>' --or \
-e '\<iowrite32_rep\>' --or \
-e '\<iowrite64_rep\>' --or \
-e '\<__io_virt\>' --or \
-e '\<pci_iounmap\>' --or \
-e '\<virt_to_phys\>' --or \
-e '\<phys_to_virt\>' --or \
-e '\<ioremap_uc\>' --or \
-e '\<ioremap\>' --or \
-e '\<__ioremap\>' --or \
-e '\<iounmap\>' --or \
-e '\<ioremap\>' --or \
-e '\<ioremap_nocache\>' --or \
-e '\<ioremap_uc\>' --or \
-e '\<ioremap_wc\>' --or \
-e '\<ioremap_wc\>' --or \
-e '\<ioremap_wt\>' --or \
-e '\<ioport_map\>' --or \
-e '\<ioport_unmap\>' --or \
-e '\<ioport_map\>' --or \
-e '\<ioport_unmap\>' --or \
-e '\<xlate_dev_kmem_ptr\>' --or \
-e '\<xlate_dev_mem_ptr\>' --or \
-e '\<unxlate_dev_mem_ptr\>' --or \
-e '\<virt_to_bus\>' --or \
-e '\<bus_to_virt\>' --or \
-e '\<memset_io\>' --or \
-e '\<memcpy_fromio\>' --or \
-e '\<memcpy_toio\>'
I also reordered a couple includes when they weren't alphabetical and
removed clk.h from kona, replacing it with clk-provider.h because
that driver doesn't use clk consumer APIs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The global list of all debugfs entries for the driver was painful: the
list couldn't see into the components' structs, so each component had
its own debugs show function to find the component, then find the
regset and dump it. The components also had to be careful to check
that they were actually registered in vc4 before dereferencing
themselves, in case they weren't probed on a particular platform.
They routinely failed at that.
Instead, we can have the components add their debugfs callbacks to a
little list in vc4 to be registered at drm_dev_register() time, which
gets vc4_debugfs.c out of the business of knowing the whole list of
components.
Thanks to this change, dsi0 (if it existed) would register its node.
v2: Rebase on hvs_underrun addition.
v3: whitespace fixup
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190401183559.3823-1-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
|
|
This removes a bunch of duplicated boilerplate for the debugfs vs
runtime printk debug dumping.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220210343.28157-2-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
|
|
Having the probe helper stuff (which pretty much everyone needs) in
the drm_crtc_helper.h file (which atomic drivers should never need) is
confusing. Split them out.
To make sure I actually achieved the goal here I went through all
drivers. And indeed, all atomic drivers are now free of
drm_crtc_helper.h includes.
v2: Make it compile. There was so much compile fail on arm drivers
that I figured I'll better not include any of the acks on v1.
v3: Massive rebase because i915 has lost a lot of drmP.h includes, but
not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h
there was still one, which this patch largely removes. Which means
rolling out lots more includes all over.
This will also conflict with ongoing drmP.h cleanup by others I
expect.
v3: Rebase on top of atomic bochs.
v4: Review from Laurent for bridge/rcar/omap/shmob/core bits:
- (re)move some of the added includes, use the better include files in
other places (all suggested from Laurent adopted unchanged).
- sort alphabetically
v5: Actually try to sort them, and while at it, sort all the ones I
touch.
v6: Rebase onto i915 changes.
v7: Rebase once more.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: virtualization@lists.linux-foundation.org
Cc: etnaviv@lists.freedesktop.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: spice-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-tegra@vger.kernel.org
Cc: xen-devel@lists.xen.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
|
|
Having a device with a status property != "okay" in the DT is a valid
use case, and we should not prevent the registration of the DRM device
when the DSI device connected to the DSI controller is disabled.
Consider the ENODEV return code as a valid result and do not expose the
DSI encoder/connector when it happens.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-5-boris.brezillon@bootlin.com
|
|
This allows panels or bridges that need to send DSI commands during
pre_enable() to successfully send them. We delay DISP0 (aka the
actual display) enabling until after pre_enable so that pixels aren't
streaming before then.
v2: Just clear out the encoder->bridge value to disable the midlayer
calls (idea by Andrzej Hajda).
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621231759.29604-1-eric@anholt.net
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
|
|
It seems that trying to go from unlatched to unlatched will time out
waiting for STOP, and we can just skip that.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031193258.17373-1-eric@anholt.net
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
VC4's DSI1 has a bug where the AXI connection is broken for 32-bit
writes from the CPU, so we use the DMA engine to DMA 32-bit values
into registers instead. That sleeps, so we can't do it from the top
half.
As a solution, use an interrupt thread so that all our writes happen
when sleeping is is allowed.
v2: Use IRQF_ONESHOT (suggested by Boris)
v3: Style nitpicks.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20171014001255.32005-1-eric@anholt.net
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> (v2)
|
|
We want the adjusted_mode->clock to be the actual clock we're
expecting to program, so that consumers see the right values for clock
and vrefresh.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815234722.20700-1-eric@anholt.net
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
We need the following things to happen in sequence:
DSI host creation
DSI device creation in the panel driver (needs DSI host)
DSI device attach from panel to host.
DSI drm_panel_add()
DSI encoder creation
DSI encoder's DRM panel/bridge attach
Unless we allow device creation while the host isn't up yet, we need
to break the -EPROBE_DEFER deadlock between the panel driver looking
up the host and the host driver looking up the panel. We can do so by
moving the DSI host creation outside of the component bind loop, and
the panel/bridge lookup/attach into the component bind process.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815234722.20700-3-eric@anholt.net
Reviewed-by: Archit Taneja <architt@codeaurora.org>
|
|
The incoming mode might have a missing vrefresh field if it came from
drmModeSetCrtc(), which the kernel is supposed to calculate using
drm_mode_vrefresh(). We could either use that or the adjusted_mode's
original vrefresh value.
However, we can maintain a more exact vrefresh value (not just the
integer approximation), by scaling by the ratio of our clocks.
v2: Use math suggested by Andrzej Hajda instead.
v3: Simplify math now that adjusted_mode->clock isn't padded.
v4: Drop some parens.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815234722.20700-2-eric@anholt.net
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
|
|
drm_bridge_remove() is for unregistering a bridge driver, not for
detaching a bridge from its consumer.
Fixes: 656fa22f9cea ("drm/vc4: Switch DSI to the panel-bridge layer, and support bridges.")
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170802203242.12815-3-eric@anholt.net
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The clocks are enabled/disabled at encoder enable/disable time, not at
component load. Fixes a WARN_ON at boot if V3D fails to probe.
Fixes: 4078f5757144 ("drm/vc4: Add DSI driver")
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170802203242.12815-2-eric@anholt.net
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The logic was all right in the end, the name was just backwards.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170627195839.3338-3-eric@anholt.net
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
|
|
The DPHY spec requires a much larger T_INIT than I was specifying
before. In the absence of clear specs from the slave of what their
timing is, just use the value that the firmware was using.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170627195839.3338-2-eric@anholt.net
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
|
|
The newer version of the RPi panel driver is going to be a combination
of a bridge and a panel, but we should also support panels without a
bridge, so the panel-bridge layer lets us do that cleanly.
v2: Drop "dev" argument.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511183128.25085-2-eric@anholt.net
|
|
Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.
While we are here, use <...> instead of "..." for include/linux/*.h
and include/sound/*.h headers too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1495081793-9707-2-git-send-email-yamada.masahiro@socionext.com
|
|
BCM2835's PLLD_DSI1 divider doesn't give us many choices for our pixel
clocks, so to support panels on the Raspberry Pi we need to set a
higher pixel clock rate than requested and adjust the mode we program
to extend out the HFP so that the refresh rate matches.
v2: Drop an unfinished comment (caught by Noralf)
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511235625.22427-2-eric@anholt.net
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
I'm going to hook vc4 up to the sphinx build, so clean up its comments
to not generate warnings when we do.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227201144.10970-2-eric@anholt.net
|
|
If dsi_connector fails to allocate, the exit path via label 'fail'
checks if connector is null, which it always is, so the cleanup
that destroys connector is never going to be called. Hence the
failure path can be more optimally performed by removing this
and just returning ERR_PTR(-ENOMEM). This also removes the need
to initialize connector to NULL, and we can also remove ret too.
Detected by CoverityScan, CID#1399504 ("Logicall Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170203195624.7189-1-colin.king@canonical.com
|
|
The DSI0 and DSI1 blocks on the 2835 are related hardware blocks.
Some registers move around, and the featureset is slightly different,
as DSI1 (the 4-lane DSI) is a later version of the hardware block.
This driver doesn't yet enable DSI0, since we don't have any hardware
to test against, but it does put a lot of the register definitions and
code in place.
v2: Use the clk_hw interfaces, don't set CLK_IS_BASIC (from review by
Stephen Boyd)
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/20170131192912.11316-1-eric@anholt.net
|
