summaryrefslogtreecommitdiffstats
path: root/drivers/gpu/drm/nouveau
AgeCommit message (Collapse)AuthorFilesLines
2018-05-10drm/nouveau: Fix deadlock in nv50_mstm_register_connector()Lyude Paul1-4/+3
Currently; we're grabbing all of the modesetting locks before adding MST connectors to fbdev. This isn't actually necessary, and causes a deadlock as well: ====================================================== WARNING: possible circular locking dependency detected 4.17.0-rc3Lyude-Test+ #1 Tainted: G O ------------------------------------------------------ kworker/1:0/18 is trying to acquire lock: 00000000c832f62d (&helper->lock){+.+.}, at: drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] but task is already holding lock: 00000000942e28e2 (crtc_ww_class_mutex){+.+.}, at: drm_modeset_backoff+0x8e/0x1c0 [drm] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (crtc_ww_class_mutex){+.+.}: ww_mutex_lock+0x43/0x80 drm_modeset_lock+0x71/0x130 [drm] drm_helper_probe_single_connector_modes+0x7d/0x6b0 [drm_kms_helper] drm_setup_crtcs+0x15e/0xc90 [drm_kms_helper] __drm_fb_helper_initial_config_and_unlock+0x29/0x480 [drm_kms_helper] nouveau_fbcon_init+0x138/0x1a0 [nouveau] nouveau_drm_load+0x173/0x7e0 [nouveau] drm_dev_register+0x134/0x1c0 [drm] drm_get_pci_dev+0x8e/0x160 [drm] nouveau_drm_probe+0x1a9/0x230 [nouveau] pci_device_probe+0xcd/0x150 driver_probe_device+0x30b/0x480 __driver_attach+0xbc/0xe0 bus_for_each_dev+0x67/0x90 bus_add_driver+0x164/0x260 driver_register+0x57/0xc0 do_one_initcall+0x4d/0x323 do_init_module+0x5b/0x1f8 load_module+0x20e5/0x2ac0 __do_sys_finit_module+0xb7/0xd0 do_syscall_64+0x60/0x1b0 entry_SYSCALL_64_after_hwframe+0x49/0xbe -> #2 (crtc_ww_class_acquire){+.+.}: drm_helper_probe_single_connector_modes+0x58/0x6b0 [drm_kms_helper] drm_setup_crtcs+0x15e/0xc90 [drm_kms_helper] __drm_fb_helper_initial_config_and_unlock+0x29/0x480 [drm_kms_helper] nouveau_fbcon_init+0x138/0x1a0 [nouveau] nouveau_drm_load+0x173/0x7e0 [nouveau] drm_dev_register+0x134/0x1c0 [drm] drm_get_pci_dev+0x8e/0x160 [drm] nouveau_drm_probe+0x1a9/0x230 [nouveau] pci_device_probe+0xcd/0x150 driver_probe_device+0x30b/0x480 __driver_attach+0xbc/0xe0 bus_for_each_dev+0x67/0x90 bus_add_driver+0x164/0x260 driver_register+0x57/0xc0 do_one_initcall+0x4d/0x323 do_init_module+0x5b/0x1f8 load_module+0x20e5/0x2ac0 __do_sys_finit_module+0xb7/0xd0 do_syscall_64+0x60/0x1b0 entry_SYSCALL_64_after_hwframe+0x49/0xbe -> #1 (&dev->mode_config.mutex){+.+.}: drm_setup_crtcs+0x10c/0xc90 [drm_kms_helper] __drm_fb_helper_initial_config_and_unlock+0x29/0x480 [drm_kms_helper] nouveau_fbcon_init+0x138/0x1a0 [nouveau] nouveau_drm_load+0x173/0x7e0 [nouveau] drm_dev_register+0x134/0x1c0 [drm] drm_get_pci_dev+0x8e/0x160 [drm] nouveau_drm_probe+0x1a9/0x230 [nouveau] pci_device_probe+0xcd/0x150 driver_probe_device+0x30b/0x480 __driver_attach+0xbc/0xe0 bus_for_each_dev+0x67/0x90 bus_add_driver+0x164/0x260 driver_register+0x57/0xc0 do_one_initcall+0x4d/0x323 do_init_module+0x5b/0x1f8 load_module+0x20e5/0x2ac0 __do_sys_finit_module+0xb7/0xd0 do_syscall_64+0x60/0x1b0 entry_SYSCALL_64_after_hwframe+0x49/0xbe -> #0 (&helper->lock){+.+.}: __mutex_lock+0x70/0x9d0 drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] nv50_mstm_register_connector+0x2c/0x50 [nouveau] drm_dp_add_port+0x2f5/0x420 [drm_kms_helper] drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper] drm_dp_add_port+0x33f/0x420 [drm_kms_helper] drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper] drm_dp_check_and_send_link_address+0x87/0xd0 [drm_kms_helper] drm_dp_mst_link_probe_work+0x4d/0x80 [drm_kms_helper] process_one_work+0x20d/0x650 worker_thread+0x3a/0x390 kthread+0x11e/0x140 ret_from_fork+0x3a/0x50 other info that might help us debug this: Chain exists of: &helper->lock --> crtc_ww_class_acquire --> crtc_ww_class_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(crtc_ww_class_mutex); lock(crtc_ww_class_acquire); lock(crtc_ww_class_mutex); lock(&helper->lock); *** DEADLOCK *** 5 locks held by kworker/1:0/18: #0: 000000004a05cd50 ((wq_completion)"events_long"){+.+.}, at: process_one_work+0x187/0x650 #1: 00000000601c11d1 ((work_completion)(&mgr->work)){+.+.}, at: process_one_work+0x187/0x650 #2: 00000000586ca0df (&dev->mode_config.mutex){+.+.}, at: drm_modeset_lock_all+0x3a/0x1b0 [drm] #3: 00000000d3ca0ffa (crtc_ww_class_acquire){+.+.}, at: drm_modeset_lock_all+0x44/0x1b0 [drm] #4: 00000000942e28e2 (crtc_ww_class_mutex){+.+.}, at: drm_modeset_backoff+0x8e/0x1c0 [drm] stack backtrace: CPU: 1 PID: 18 Comm: kworker/1:0 Tainted: G O 4.17.0-rc3Lyude-Test+ #1 Hardware name: Gateway FX6840/FX6840, BIOS P01-A3 05/17/2010 Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper] Call Trace: dump_stack+0x85/0xcb print_circular_bug.isra.38+0x1ce/0x1db __lock_acquire+0x128f/0x1350 ? lock_acquire+0x9f/0x200 ? lock_acquire+0x9f/0x200 ? __ww_mutex_lock.constprop.13+0x8f/0x1000 lock_acquire+0x9f/0x200 ? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] ? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] __mutex_lock+0x70/0x9d0 ? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] ? ww_mutex_lock+0x43/0x80 ? _cond_resched+0x15/0x30 ? ww_mutex_lock+0x43/0x80 ? drm_modeset_lock+0xb2/0x130 [drm] ? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] nv50_mstm_register_connector+0x2c/0x50 [nouveau] drm_dp_add_port+0x2f5/0x420 [drm_kms_helper] ? mark_held_locks+0x50/0x80 ? kfree+0xcf/0x2a0 ? drm_dp_check_mstb_guid+0xd6/0x120 [drm_kms_helper] ? trace_hardirqs_on_caller+0xed/0x180 ? drm_dp_check_mstb_guid+0xd6/0x120 [drm_kms_helper] drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper] drm_dp_add_port+0x33f/0x420 [drm_kms_helper] ? nouveau_connector_aux_xfer+0x7c/0xb0 [nouveau] ? find_held_lock+0x2d/0x90 ? drm_dp_dpcd_access+0xd9/0xf0 [drm_kms_helper] ? __mutex_unlock_slowpath+0x3b/0x280 ? drm_dp_dpcd_access+0xd9/0xf0 [drm_kms_helper] drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper] drm_dp_check_and_send_link_address+0x87/0xd0 [drm_kms_helper] drm_dp_mst_link_probe_work+0x4d/0x80 [drm_kms_helper] process_one_work+0x20d/0x650 worker_thread+0x3a/0x390 ? process_one_work+0x650/0x650 kthread+0x11e/0x140 ? kthread_create_worker_on_cpu+0x50/0x50 ret_from_fork+0x3a/0x50 Taking example from i915, the only time we need to hold any modesetting locks is when changing the port on the mstc, and in that case we only need to hold the connection mutex. Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: Karol Herbst <kherbst@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-05-10drm/nouveau/ttm: don't dereference nvbo::cli, it can outlive clientBen Skeggs3-6/+3
Potentially responsible for some random OOPSes. Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: stable@vger.kernel.org [v4.15+]
2018-03-28Backmerge tag 'v4.16-rc7' into drm-nextDave Airlie5-16/+25
Linux 4.16-rc7 This was requested by Daniel, and things were getting a bit hard to reconcile, most of the conflicts were trivial though.
2018-03-21Merge airlied/drm-next into drm-misc-nextSean Paul3-15/+10
Refresh -misc-next Signed-off-by: Sean Paul <seanpaul@chromium.org>
2018-03-16Merge branch 'linux-4.16' of git://github.com/skeggsb/linux into drm-fixesDave Airlie2-8/+8
nouveau regression fixes. * 'linux-4.16' of git://github.com/skeggsb/linux: drm/nouveau/bl: fix backlight regression drm/nouveau/bl: Fix oops on driver unbind drm/nouveau/mmu: ALIGN_DOWN correct variable
2018-03-16drm/nouveau/bl: fix backlight regressionKarol Herbst1-5/+5
Fixes: 3c66c87dc9 ("drm/nouveau/disp: remove hw-specific customisation of output paths") Suggested-by: Ben Skeggs <skeggsb@redhat.com> Signed-off-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-03-16drm/nouveau/bl: Fix oops on driver unbindLukas Wunner1-2/+2
Unbinding nouveau on a dual GPU MacBook Pro oopses because we iterate over the bl_connectors list in nouveau_backlight_exit() but skipped initializing it in nouveau_backlight_init(). Stacktrace for posterity: BUG: unable to handle kernel NULL pointer dereference at 0000000000000010 IP: nouveau_backlight_exit+0x2b/0x70 [nouveau] nouveau_display_destroy+0x29/0x80 [nouveau] nouveau_drm_unload+0x65/0xe0 [nouveau] drm_dev_unregister+0x3c/0xe0 [drm] drm_put_dev+0x2e/0x60 [drm] nouveau_drm_device_remove+0x47/0x70 [nouveau] pci_device_remove+0x36/0xb0 device_release_driver_internal+0x157/0x220 driver_detach+0x39/0x70 bus_remove_driver+0x51/0xd0 pci_unregister_driver+0x2a/0xa0 nouveau_drm_exit+0x15/0xfb0 [nouveau] SyS_delete_module+0x18c/0x290 system_call_fast_compare_end+0xc/0x6f Fixes: b53ac1ee12a3 ("drm/nouveau/bl: Do not register interface if Apple GMUX detected") Cc: stable@vger.kernel.org # v4.10+ Cc: Pierre Moreau <pierre.morrow@free.fr> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-03-16drm/nouveau/mmu: ALIGN_DOWN correct variableMāris Nartišs1-1/+1
Commit 7110c89bb8852ff8b0f88ce05b332b3fe22bd11e ("mmu: swap out round for ALIGN") replaced two calls to round/rounddown with ALIGN/ALIGN_DOWN, but erroneously applied ALIGN_DOWN to a different variable (addr) and left intended variable (tail) not rounded/ALIGNed. As a result screen corruption, X lockups are observable. An example of kernel log of affected system with NV98 card where it was bisected: nouveau 0000:01:00.0: gr: TRAP_M2MF 00000002 [IN] nouveau 0000:01:00.0: gr: TRAP_M2MF 00320951 400007c0 00000000 04000000 nouveau 0000:01:00.0: gr: 00200000 [] ch 1 [000fbbe000 DRM] subc 4 class 5039 mthd 0100 data 00000000 nouveau 0000:01:00.0: fb: trapped read at 0040000000 on channel 1 [0fbbe000 DRM] engine 00 [PGRAPH] client 03 [DISPATCH] subclient 04 [M2M_IN] reason 00000006 [NULL_DMAOBJ] Fixes bug 105173 ("[MCP79][Regression] Unhandled NULL pointer dereference in nvkm_object_unmap since kernel 4.15") https://bugs.freedesktop.org/show_bug.cgi?id=105173 Fixes: 7110c89bb885 ("mmu: swap out round for ALIGN ") Tested-by: Pierre Moreau <pierre.morrow@free.fr> Reviewed-by: Pierre Moreau <pierre.morrow@free.fr> Signed-off-by: Maris Nartiss <maris.nartiss@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: stable@vger.kernel.org # v4.15+
2018-03-14drm/ttm: add bo as parameter to the ttm_tt_create callbackChristian König3-12/+9
Instead of calculating the size in bytes just to recalculate the number of pages from it pass the BO directly to the function. Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Roger He <Hongbo.He@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-03-14Merge tag 'drm-misc-next-2018-03-09-3' of ↵Dave Airlie2-25/+13
git://anongit.freedesktop.org/drm/drm-misc into drm-next drm-misc-next for 4.17: UAPI Changes: plane: Add color encoding/range properties (Jyri) nouveau: Replace iturbt_709 property with color_encoding property (Ville) Core Changes: atomic: Move plane clipping into plane check helper (Ville) property: Multiple new property checks/verification (Ville) Driver Changes: rockchip: Fixes & improvements for rk3399/chromebook plus (various) sun4i: Add H3/H5 HDMI support (Jernej) i915: Add support for limited/full-range ycbcr toggling (Ville) pl111: Add bandwidth checking/limiting (Linus) Cc: Jernej Skrabec <jernej.skrabec@siol.net> Cc: Jyri Sarha <jsarha@ti.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Linus Walleij <linus.walleij@linaro.org> * tag 'drm-misc-next-2018-03-09-3' of git://anongit.freedesktop.org/drm/drm-misc: (85 commits) drm/rockchip: Don't use atomic constructs for psr drm/rockchip: analogix_dp: set psr activate/deactivate when enable/disable bridge drm/rockchip: dw_hdmi: Move HDMI vpll clock enable to bind() drm/rockchip: inno_hdmi: reorder clk_disable_unprepare call in unbind drm/rockchip: inno_hdmi: Fix error handling path. drm/rockchip: dw-mipi-dsi: Fix connector and encoder cleanup. drm/nouveau: Replace the iturbt_709 prop with the standard COLOR_ENCODING prop drm/pl111: Use max memory bandwidth for resolution drm/bridge: sii902x: Retry status read after DDI I2C drm/pl111: Handle the RealView variant separately drm/pl111: Make the default BPP a per-variant variable drm: simple_kms_helper: Fix .mode_valid() documentation bridge: Elaborate a bit on dumb VGA bridges in Kconfig drm/atomic: Add new reverse iterator over all plane state (V2) drm: Reject bad property flag combinations drm: Make property flags u32 drm/uapi: Deprecate DRM_MODE_PROP_PENDING drm: WARN when trying to add enum value > 63 to a bitmask property drm: WARN when trying add enum values to non-enum/bitmask properties drm: Reject replacing property enum values ...
2018-03-13drm/nouveau: Runtime suspend despite HDA being unboundLukas Wunner2-45/+0
Commit 5addcf0a5f0f ("nouveau: add runtime PM support (v0.9)") prevents runtime suspend of the GPU if its integrated HDA controller is not bound to a driver. The rationale appears to be that probing the HDA fails if the GPU is in D3cold. However we now use a device link to ensure that the GPU is runtime resumed while the HDA controller is probed, rendering this safety measure obsolete. Remove it. Cc: Dave Airlie <airlied@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Peter Wu <peter@lekensteyn.nl> Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://patchwork.freedesktop.org/patch/msgid/77e0ab74f3377ea9b6acf8fab624acfb4f7dbeca.1520068884.git.lukas@wunner.de
2018-03-13vga_switcheroo: Use device link for HDA controllerLukas Wunner1-2/+0
Back in 2013, runtime PM for GPUs with integrated HDA controller was introduced with commits 0d69704ae348 ("gpu/vga_switcheroo: add driver control power feature. (v3)") and 246efa4a072f ("snd/hda: add runtime suspend/resume on optimus support (v4)"). Briefly, the idea was that the HDA controller is forced on and off in unison with the GPU. The original code is mostly still in place even though it was never a 100% perfect solution: E.g. on access to the HDA controller, the GPU is powered up via vga_switcheroo_runtime_resume_hdmi_audio() but there are no provisions to keep it resumed until access to the HDA controller has ceased: The GPU autosuspends after 5 seconds, rendering the HDA controller inaccessible. Additionally, a kludge is required when hda_intel.c probes: It has to check whether the GPU is powered down (check_hdmi_disabled()) and defer probing if so. However in the meantime (in v4.10) the driver core has gained a feature called device links which promises to solve such issues in a clean way: It allows us to declare a dependency from the HDA controller (consumer) to the GPU (supplier). The PM core then automagically ensures that the GPU is runtime resumed as long as the HDA controller's ->probe hook is executed and whenever the HDA controller is accessed. By default, the HDA controller has a dependency on its parent, a PCIe Root Port. Adding a device link creates another dependency on its sibling: PCIe Root Port ^ ^ | | | | HDA ===> GPU The device link is not only used for runtime PM, it also guarantees that on system sleep, the HDA controller suspends before the GPU and resumes after the GPU, and on system shutdown the HDA controller's ->shutdown hook is executed before the one of the GPU. It is a complete solution. Using this functionality is as simple as calling device_link_add(), which results in a dmesg entry like this: pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0 The code for the GPU-governed audio power management can thus be removed (except where it's still needed for legacy manual power control). The device link is added in a PCI quirk rather than in hda_intel.c. It is therefore legal for the GPU to runtime suspend to D3cold even if the HDA controller is not bound to a driver or if CONFIG_SND_HDA_INTEL is not enabled, for accesses to the HDA controller will cause the GPU to wake up regardless if they're occurring outside of hda_intel.c (think config space readout via sysfs). Contrary to the previous implementation, the HDA controller's power state is now self-governed, rather than GPU-governed, whereas the GPU's power state is no longer fully self-governed. (The HDA controller needs to runtime suspend before the GPU can.) It is thus crucial that runtime PM is always activated on the HDA controller even if CONFIG_SND_HDA_POWER_SAVE_DEFAULT is set to 0 (which is the default), lest the GPU stays awake. This is achieved by setting the auto_runtime_pm flag on every codec and the AZX_DCAPS_PM_RUNTIME flag on the HDA controller. A side effect is that power consumption might be reduced if the GPU is in use but the HDA controller is not, because the HDA controller is now allowed to go to D3hot. Before, it was forced to stay in D0 as long as the GPU was in use. (There is no reduction in power consumption on my Nvidia GK107, but there might be on other chips.) The code paths for legacy manual power control are adjusted such that runtime PM is disabled during power off, thereby preventing the PM core from resuming the HDA controller. Note that the device link is not only added on vga_switcheroo capable systems, but for *any* GPU with integrated HDA controller. The idea is that the HDA controller streams audio via connectors located on the GPU, so the GPU needs to be on for the HDA controller to do anything useful. This commit implicitly fixes an unbalanced runtime PM ref upon unbind of hda_intel.c: On ->probe, a runtime PM ref was previously released under the condition "azx_has_pm_runtime(chip) || hda->use_vga_switcheroo", but on ->remove a runtime PM ref was only acquired under the first of those conditions. Thus, binding and unbinding the driver twice on a vga_switcheroo capable system caused the runtime PM refcount to drop below zero. The issue is resolved because the AZX_DCAPS_PM_RUNTIME flag is now always set if use_vga_switcheroo is true. For more information on device links please refer to: https://www.kernel.org/doc/html/latest/driver-api/device_link.html Documentation/driver-api/device_link.rst Cc: Dave Airlie <airlied@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Peter Wu <peter@lekensteyn.nl> Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://patchwork.freedesktop.org/patch/msgid/51bd38360ff502a8c42b1ebf4405ee1d3f27118d.1520068884.git.lukas@wunner.de
2018-03-08drm/nouveau: Replace the iturbt_709 prop with the standard COLOR_ENCODING propVille Syrjälä1-13/+13
Replace the ad-hoc iturbt_709 property with the new standard COLOR_ENCODING property. Compiles, but not tested. v2: Fix typos (Ilia) Cc: Daniel Vetter <daniel@ffwll.ch> Cc: nouveau@lists.freedesktop.org Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180220134816.15229-1-ville.syrjala@linux.intel.com Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu> Acked-by: Ben Skeggs <bskeggs@redhat.com> #irc
2018-03-05drm: Don't pass clip to drm_atomic_helper_check_plane_state()Ville Syrjälä1-12/+0
Move the plane clip rectangle handling into drm_atomic_helper_check_plane_state(). Drivers no longer have to worry about such mundane details. v2: Convert armada, rcar, and sun4i as well v3: Resolve simple_kms_helper conflict Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Brian Starkey <brian.starkey@arm.com> Cc: Mali DP Maintainers <malidp@foss.arm.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Sean Paul <seanpaul@chromium.org> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: CK Hu <ck.hu@mediatek.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Rob Clark <robdclark@gmail.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Sandy Huang <hjc@rock-chips.com> Cc: "Heiko Stübner" <heiko@sntech.de> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: VMware Graphics <linux-graphics-maintainer@vmware.com> Cc: Sinclair Yeh <syeh@vmware.com> Cc: Thomas Hellstrom <thellstrom@vmware.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Archit Taneja <architt@codeaurora.org> Cc: linux-amlogic@lists.infradead.org Cc: linux-arm-msm@vger.kernel.org Cc: freedreno@lists.freedesktop.org Cc: nouveau@lists.freedesktop.org Cc: linux-renesas-soc@vger.kernel.org Cc: linux-tegra@vger.kernel.org Cc: Russell King <rmk+kernel@armlinux.org.uk> Suggested-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Archit Taneja <architt@codeaurora.org> #msm Link: https://patchwork.freedesktop.org/patch/msgid/20180123170857.13818-5-ville.syrjala@linux.intel.com Acked-by: Liviu Dudau <liviu.dudau@arm.com> #hdlcd,malidp Acked-by: Philipp Zabel <p.zabel@pengutronix.de> #imx,mtk Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> #vmwgfx Acked-by: Neil Armstrong <narmstrong@baylibre.com> #meson Acked-by: Shawn Guo <shawnguo@kernel.org> #zte
2018-02-26drm/ttm: drop persistent_swap_storage from ttm_bo_init and coChristian König1-1/+1
Never used as parameter, the only driver actually using this is nouveau and there it is initialized after the BO is initialized. Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-02-26drm/ttm: drop ttm->dummy_read_pageChristian König3-8/+6
Only used by the AGP backend and there it can be easily accessed using ttm->bdev->glob. Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-02-23drm/nouveau: prefer XBGR2101010 for addfb ioctlIlia Mirkin1-0/+1
Nouveau only exposes support for XBGR2101010. Prior to the atomic conversion, drm would pass in the wrong format in the framebuffer, but it was always ignored -- both userspace (xf86-video-nouveau) and the kernel driver agreed on the layout, so the fact that the format was wrong didn't matter. With the atomic conversion, nouveau all of a sudden started caring about the exact format, and so the previously-working code in xf86-video-nouveau no longer functioned since the (internally-assigned) format from the addfb ioctl was wrong. This change adds infrastructure to allow a drm driver to specify that it prefers the XBGR format variant for the addfb ioctl, and makes nouveau's nv50 display driver set it. (Prior gens had no support for 30bpp at all.) Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Cc: stable@vger.kernel.org # v4.10+ Acked-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20180203191123.31507-1-imirkin@alum.mit.edu
2018-02-22Merge tag 'drm-misc-fixes-2018-02-21' of ↵Dave Airlie1-5/+13
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes Fixes for 4.16. I contains fixes for deadlock on runtime suspend on few drivers, a memory leak on non-blocking commits, a crash on color-eviction. The is also meson and edid fixes, plus a fix for a doc warning. * tag 'drm-misc-fixes-2018-02-21' of git://anongit.freedesktop.org/drm/drm-misc: drm/tve200: fix kernel-doc documentation comment include drm/meson: fix vsync buffer update drm: Handle unexpected holes in color-eviction drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA drm/amdgpu: Fix deadlock on runtime suspend drm/radeon: Fix deadlock on runtime suspend drm/nouveau: Fix deadlock on runtime suspend drm: Allow determining if current task is output poll worker workqueue: Allow retrieval of current task's work struct drm/atomic: Fix memleak on ERESTARTSYS during non-blocking commits
2018-02-16drm/nouveau: Fix deadlock on runtime suspendLukas Wunner1-5/+13
nouveau's ->runtime_suspend hook calls drm_kms_helper_poll_disable(), which waits for the output poll worker to finish if it's running. The output poll worker meanwhile calls pm_runtime_get_sync() in nouveau_connector_detect() which waits for the ongoing suspend to finish, causing a deadlock. Fix by not acquiring a runtime PM ref if nouveau_connector_detect() is called in the output poll worker's context. This is safe because the poll worker is only enabled while runtime active and we know that ->runtime_suspend waits for it to finish. Other contexts calling nouveau_connector_detect() do require a runtime PM ref, these comprise: status_store() drm sysfs interface ->fill_modes drm callback drm_fb_helper_probe_connector_modes() drm_mode_getconnector() nouveau_connector_hotplug() nouveau_display_hpd_work() nv17_tv_set_property() Stack trace for posterity: INFO: task kworker/0:1:58 blocked for more than 120 seconds. Workqueue: events output_poll_execute [drm_kms_helper] Call Trace: schedule+0x28/0x80 rpm_resume+0x107/0x6e0 __pm_runtime_resume+0x47/0x70 nouveau_connector_detect+0x7e/0x4a0 [nouveau] nouveau_connector_detect_lvds+0x132/0x180 [nouveau] drm_helper_probe_detect_ctx+0x85/0xd0 [drm_kms_helper] output_poll_execute+0x11e/0x1c0 [drm_kms_helper] process_one_work+0x184/0x380 worker_thread+0x2e/0x390 INFO: task kworker/0:2:252 blocked for more than 120 seconds. Workqueue: pm pm_runtime_work Call Trace: schedule+0x28/0x80 schedule_timeout+0x1e3/0x370 wait_for_completion+0x123/0x190 flush_work+0x142/0x1c0 nouveau_pmops_runtime_suspend+0x7e/0xd0 [nouveau] pci_pm_runtime_suspend+0x5c/0x180 vga_switcheroo_runtime_suspend+0x1e/0xa0 __rpm_callback+0xc1/0x200 rpm_callback+0x1f/0x70 rpm_suspend+0x13c/0x640 pm_runtime_work+0x6e/0x90 process_one_work+0x184/0x380 worker_thread+0x2e/0x390 Bugzilla: https://bugs.archlinux.org/task/53497 Bugzilla: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=870523 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70388#c33 Fixes: 5addcf0a5f0f ("nouveau: add runtime PM support (v0.9)") Cc: stable@vger.kernel.org # v3.12+: 27d4ee03078a: workqueue: Allow retrieval of current task's work struct Cc: stable@vger.kernel.org # v3.12+: 25c058ccaf2e: drm: Allow determining if current task is output poll worker Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Dave Airlie <airlied@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://patchwork.freedesktop.org/patch/msgid/b7d2cbb609a80f59ccabfdf479b9d5907c603ea1.1518338789.git.lukas@wunner.de
2018-02-16Merge branch 'linux-4.16' of git://github.com/skeggsb/linux into drm-fixesDave Airlie1-3/+3
single fix for older gpus. * 'linux-4.16' of git://github.com/skeggsb/linux: drm/nouveau: Make clock gate support conditional
2018-02-16drm/nouveau: Make clock gate support conditionalThierry Reding1-3/+3
The recently introduced clock gate support breaks on Tegra chips because no thermal support is enabled for those devices. Conditionalize the code on the existence of thermal support to fix this. Fixes: b138eca661cc ("drm/nouveau: Add support for basic clockgating on Kepler1") Cc: Martin Peres <martin.peres@free.fr> Cc: Lyude Paul <lyude@redhat.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-16Merge tag 'drm-misc-next-2018-02-13' of ↵Dave Airlie1-8/+12
git://anongit.freedesktop.org/drm/drm-misc into drm-next drm-misc-next for 4.17: UAPI Changes: - drm/vc4: Expose performance counters to userspace (Boris) Cross-subsystem Changes: - MAINTAINERS: Linus to maintain panel-arm-versatile in -misc (Linus) Core Changes: - Only use swiotlb when necessary (Chunming) Driver Changes: - drm/panel: Add support for ARM Versatile panels (Linus) - pl111: Improvements around versatile panel support (Linus) ---------------------------------------- Tagged on 2018-02-06: drm-misc-next for 4.17: UAPI Changes: - Validate mode flags + type (Ville) - Deprecate unused mode flags PIXMUX, BCAST (Ville) - Deprecate unused mode types BUILTIN, CRTC_C, CLOCK_C, DEFAULT (Ville) Cross-subsystem Changes: - MAINTAINERS: s/Daniel/Maarten/ for drm-misc (Daniel) Core Changes: - gem: Export gem functions for drivers to use (Samuel) - bridge: Introduce bridge timings in drm_bridge (Linus) - dma-buf: Allow exclusive fence to be bundled in fence array when calling reservation_object_get_fences_rcu (Christian) - dp: Add training pattern 4 and HBR3 support to dp helpers (Manasi) - fourcc: Add alpha bit to formats to avoid driver format LUTs (Maxime) - mode: Various cleanups + add new device-wide .mode_valid hook (Ville) - atomic: Fix state leak when non-blocking commits fail (Leo) NOTE: IIRC, this was cross-picked to -fixes so it might fall out - crc: Allow polling on the data fd (Maarten) Driver Changes: - bridge/vga-dac: Add THS8134* support (Linus) - tinydrm: Various MIPI DBI improvements/cleanups (Noralf) - bridge/dw-mipi-dsi: Cleanups + use create_packet helper (Brian) - drm/sun4i: Add Display Engine frontend support (Maxime) - drm/sun4i: Add zpos support + increase num planes from 2 to 4 (Maxime) - various: Use drm_mode_get_hv_timing() to fill plane clip rectangle (Ville) - stm: Add 8-bit clut support, add dsi phy v1.31 support, +fixes (Phillipe) Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Chunming Zhou <david1.zhou@amd.com> Cc: Samuel Li <Samuel.Li@amd.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Noralf Trønnes <noralf@tronnes.org> Cc: Brian Norris <briannorris@chromium.org> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Christian König <christian.koenig@amd.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Philippe Cornu <philippe.cornu@st.com> Cc: Leo (Sunpeng) Li <sunpeng.li@amd.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> * tag 'drm-misc-next-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc: (115 commits) drm/radeon: only enable swiotlb path when need v2 drm/amdgpu: only enable swiotlb alloc when need v2 drm: add func to get max iomem address v2 drm/vc4: Expose performance counters to userspace drm: Print the pid when debug logging an ioctl error. drm/stm: ltdc: remove non-alpha color formats on layer 2 for older hw drm/stm: ltdc: add non-alpha color formats drm/bridge/synopsys: dsi: Add 1.31 version support drm/bridge/synopsys: dsi: Add read feature drm/pl111: Support multiple endpoints on the CLCD drm/pl111: Support variants with broken VBLANK drm/pl111: Support variants with broken clock divider drm/pl111: Handle the Versatile RGB/BGR565 mode drm/pl111: Properly detect the ARM PL110 variants drm/panel: Add support for ARM Versatile panels drm/panel: Device tree bindings for ARM Versatile panels drm/bridge: Rename argument from crtc to bridge drm/crc: Add support for polling on the data fd. drm/sun4i: Use drm_mode_get_hv_timing() to populate plane clip rectangle drm/rcar-du: Use drm_mode_get_hv_timing() to populate plane clip rectangle ...
2018-02-08Merge tag 'drm-for-v4.16-part2-fixes' of ↵Linus Torvalds44-1491/+2723
git://people.freedesktop.org/~airlied/linux Pull more drm updates from Dave Airlie: "Ben missed sending his nouveau tree, but he really didn't have much stuff in it: - GP108 acceleration support is enabled by "secure boot" support - some clockgating work on Kepler, and bunch of fixes - the bulk of the diff is regenerated firmware files, the change to them really isn't that large. Otherwise this contains regular Intel and AMDGPU fixes" * tag 'drm-for-v4.16-part2-fixes' of git://people.freedesktop.org/~airlied/linux: (59 commits) drm/i915/bios: add DP max link rate to VBT child device struct drm/i915/cnp: Properly handle VBT ddc pin out of bounds. drm/i915/cnp: Ignore VBT request for know invalid DDC pin. drm/i915/cmdparser: Do not check past the cmd length. drm/i915/cmdparser: Check reg_table_count before derefencing. drm/i915/bxt, glk: Increase PCODE timeouts during CDCLK freq changing drm/i915/gvt: Use KVM r/w to access guest opregion drm/i915/gvt: Fix aperture read/write emulation when enable x-no-mmap=on drm/i915/gvt: only reset execlist state of one engine during VM engine reset drm/i915/gvt: refine intel_vgpu_submission_ops as per engine ops drm/amdgpu: re-enable CGCG on CZ and disable on ST drm/nouveau/clk: fix gcc-7 -Wint-in-bool-context warning drm/nouveau/mmu: Fix trailing semicolon drm/nouveau: Introduce NvPmEnableGating option drm/nouveau: Add support for SLCG for Kepler2 drm/nouveau: Add support for BLCG on Kepler2 drm/nouveau: Add support for BLCG on Kepler1 drm/nouveau: Add support for basic clockgating on Kepler1 drm/nouveau/kms/nv50: fix handling of gamma since atomic conversion drm/nouveau/kms/nv50: use INTERPOLATE_257_UNITY_RANGE LUT on newer chipsets ...
2018-02-06Merge tag 'pci-v4.16-changes' of ↵Linus Torvalds4-6/+21
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: - skip AER driver error recovery callbacks for correctable errors reported via ACPI APEI, as we already do for errors reported via the native path (Tyler Baicar) - fix DPC shared interrupt handling (Alex Williamson) - print full DPC interrupt number (Keith Busch) - enable DPC only if AER is available (Keith Busch) - simplify DPC code (Bjorn Helgaas) - calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn Helgaas) - enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn Helgaas) - move ASPM internal interfaces out of public header (Bjorn Helgaas) - allow hot-removal of VGA devices (Mika Westerberg) - speed up unplug and shutdown by assuming Thunderbolt controllers don't support Command Completed events (Lukas Wunner) - add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling, Jay Cornwall) - expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes) - clean up PCI DMA interface usage (Christoph Hellwig) - remove PCI pool API (replaced with DMA pool) (Romain Perier) - deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan Kaya) - move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring) - add PCI-specific wrappers for dev_info(), etc (Frederick Lawler) - remove warnings on sysfs mmap failure (Bjorn Helgaas) - quiet ROM validation messages (Alex Deucher) - remove redundant memory alloc failure messages (Markus Elfring) - fill in types for compile-time VGA and other I/O port resources (Bjorn Helgaas) - make "pci=pcie_scan_all" work for Root Ports as well as Downstream Ports to help AmigaOne X1000 (Bjorn Helgaas) - add SPDX tags to all PCI files (Bjorn Helgaas) - quirk Marvell 9128 DMA aliases (Alex Williamson) - quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas) - fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas Cassel) - use DMA API to get MSI address for DesignWare IP (Niklas Cassel) - fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I) - fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun) - add support for ARTPEC-7 SoC (Niklas Cassel) - add endpoint-mode support for ARTPEC (Niklas Cassel) - add Cadence PCIe host and endpoint controller driver (Cyrille Pitchen) - handle multiple INTx status bits being set in dra7xx (Vignesh R) - translate dra7xx hwirq range to fix INTD handling (Vignesh R) - remove deprecated Exynos PHY initialization code (Jaehoon Chung) - fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu) - fix NULL pointer dereference in iProc BCMA driver (Ray Jui) - fix Keystone interrupt-controller-node lookup (Johan Hovold) - constify qcom driver structures (Julia Lawall) - rework Tegra config space mapping to increase space available for endpoints (Vidya Sagar) - simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy) - remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy) - add support for Global Fabric Manager Server (GFMS) event to Microsemi Switchtec switch driver (Logan Gunthorpe) - add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao) * tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits) PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller PCI: endpoint: Fix EPF device name to support multi-function devices PCI: endpoint: Add the function number as argument to EPC ops PCI: cadence: Add host driver for Cadence PCIe controller dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller PCI: Add vendor ID for Cadence PCI: Add generic function to probe PCI host controllers PCI: generic: fix missing call of pci_free_resource_list() PCI: OF: Add generic function to parse and allocate PCI resources PCI: Regroup all PCI related entries into drivers/pci/Makefile PCI/DPC: Reformat DPC register definitions PCI/DPC: Add and use DPC Status register field definitions PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error() PCI/DPC: Remove unnecessary RP PIO register structs PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info() PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info() PCI/DPC: Make RP PIO log size check more generic PCI/DPC: Rename local "status" to "dpc_status" PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error() ...
2018-02-02drm/nouveau/clk: fix gcc-7 -Wint-in-bool-context warningArnd Bergmann1-3/+6
gcc thinks that interpreting a multiplication result as a bool is confusing: drivers/gpu/drm/nouveau/nvkm/subdev/clk/gt215.c: In function 'read_pll': drivers/gpu/drm/nouveau/nvkm/subdev/clk/gt215.c:133:8: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context] Adding a temporary variable to contain the divisor helps make it clear what is going on and avoids that warning. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau/mmu: Fix trailing semicolonLuis de Bethencourt1-1/+1
The trailing semicolon is an empty statement that does no operation. Removing it since it doesn't do anything. Signed-off-by: Luis de Bethencourt <luisbg@kernel.org> Reviewed-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau: Introduce NvPmEnableGating optionLyude Paul1-1/+3
This adds the NvPmEnableGating config option to nouveau, which can be used to enable or disable clockgating for supported chipsets. Enabling can be done by passing config=NvPmEnableGating=1 To nouveau. If your chipset supports it, you'll see a message in your kernel log indicating that clockgating is enabled. Since clockgating has only had limited testing thus far, we leave this option disabled by default for now. Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Martin Peres <martin.peres@free.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau: Add support for SLCG for Kepler2Lyude Paul1-0/+93
That's right, there's still more power saving to go! Starting with kepler 2, nvidia hardware has an additional level of clockgating known as second level clockgating. The details of this are not exact, but it seems to work by waiting for a collection of dependent hardware blocks to be gated before taking affect. As with the previous series, this results in another noticeable drop in power consumption and is programmed in the same manner. Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Martin Peres <martin.peres@free.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau: Add support for BLCG on Kepler2Lyude Paul5-4/+139
Same as the previous patch, but for Kepler2 now Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Martin Peres <martin.peres@free.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau: Add support for BLCG on Kepler1Lyude Paul14-1/+442
This enables BLCG optimization for kepler1. When using clockgating, nvidia's firmware has a set of registers which are initially programmed by the vbios with various engine delays and other mysterious settings that are safe enough to bring up the GPU. However, the values used by the vbios are more power hungry then they need to be, so the nvidia driver writes it's own more optimized set of BLCG settings before enabling CG_CTRL. This adds support for programming the optimized BLCG values during engine/subdev init, which enables rather significant power savings. This introduces the nvkm_therm_clkgate_init() helper, which we use to program the optimized BLCG settings before enabling clockgating with nvkm_therm_clkgate_enable. As well, this commit shares a lot more code with Fermi since BLCG is mostly the same there as far as we can tell. In the future, it's likely we'll reformat the clkgate_packs for kepler1 so that they share a list of mmio packs with Fermi. Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Martin Peres <martin.peres@free.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau: Add support for basic clockgating on Kepler1Lyude Paul9-21/+301
This adds support for enabling automatic clockgating on nvidia GPUs for Kepler1. While this is not technically a clockgating level, it does enable clockgating using the clockgating values initially set by the vbios (which should be safe to use). This introduces two therm helpers for controlling basic clockgating: nvkm_therm_clkgate_enable() - enables clockgating through CG_CTRL, done after initializing the GPU fully nvkm_therm_clkgate_fini() - prepares clockgating for suspend or driver unload A lot of this code was originally going to be based off of fermi; however it turns out that while Fermi's the first line of GPUs that introduced this kind of power saving, Fermi requires more fine tuned control of the CG_CTRL registers from the driver while reclocking that we don't entirely understand yet. For the simple parts we will be sharing with Fermi for certain however, we at least add those into a new subdev/therm/gf100.h header. Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Martin Peres <martin.peres@free.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau/kms/nv50: fix handling of gamma since atomic conversionBen Skeggs1-53/+109
We've still been directly using the legacy crtc gamma_set() hook even after conversion to atomic modesetting. For userspace clients this was fine, however, fbcon will use the atomic property when it's running on an atomic driver, which means we miss its colormap updates - which is particularly bad for 8bpp framebuffers! This commit converts the driver to use the atomic property + the helper function implementing the legacy hook on top of atomic. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80675 Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau/kms/nv50: use INTERPOLATE_257_UNITY_RANGE LUT on newer chipsetsBen Skeggs1-4/+4
For some reason forgotten by history, we've been using a 1025-entry LUT mode, and sparsely filling it with the 256-entry LUT we're handed. Until we land support for the full atomic colour management properties, this commit switches to using the 257-entry mode to fix colour mapping with depth 30 framebuffers. Reported-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau/kms/nv50: use "low res" lut for indexed modeIlia Mirkin1-2/+4
This is what was done prior to the big refactor in kernel 3.8, and what was done by xf86-video-nv. Experimentally, it seems like there's some sort of issue with the high-res lut to be used there. Tested on G92. This ends up mattering because fbcon/fbdev chooses the C8 fb format for low-vram systems, which can occur with some IGP-based configurations with little "stolen" vram. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80675 Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau/kms/nv50: prepare for double-buffered LUTsBen Skeggs2-23/+15
We need to double-buffer LUTs to handle their update atomically. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau/bo: add helper functions for handling pinned+mapped buffersBen Skeggs1-0/+28
This is a common, awkward sequence. Let's wrap it up! Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau/fbcon: add module parameter to select bits-per-pixelBen Skeggs1-8/+14
Useful for debugging. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau/secboot/gp108: implement on top of acr_r370Ben Skeggs7-1/+78
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Gourav Samaiya <gsamaiya@nvidia.com>
2018-02-02drm/nouveau/secboot/r370: implement support for booting LS SEC2 ucodeBen Skeggs1-0/+39
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Gourav Samaiya <gsamaiya@nvidia.com>
2018-02-02drm/nouveau/secboot/r370: move a bunch of r375 stuff to a new implementationBen Skeggs5-86/+163
It's entirely possibly that the other r375 code is relevant to r370 too, but I've not confirmed this, so I'll leave it where it is for now. NVIDIA's copyright headers maintained, as it's still all their code. Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Gourav Samaiya <gsamaiya@nvidia.com>
2018-02-02drm/nouveau: nouveau: use correct string lengthArnd Bergmann1-3/+3
gcc-8 reports drivers/gpu/drm/nouveau/nvkm/engine/pm/base.c: In function 'nvkm_perfmon_mthd': include/linux/string.h:265:9: error: '__builtin_strncpy' specified bound 64 equals destination size [-Werror=stringop-truncation] We need one less byte or call strlcpy() to make it a nul-terminated string. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-02drm/nouveau/drm/nouveau/mmu: fix odd_ptr_err.cocci warningsChristoph Böhmwalder1-1/+2
The kbuild test bot complained about a new coccinelle warning nearby, which sparked a discussion about the assignment to 'memory' inside of the conditional expression. See Link below for the original post. Fix the assignment to silence the coccinelle warning and also make the code look a little nicer. Link: https://lists.freedesktop.org/archives/nouveau/2017-November/029242.html Signed-off-by: Christoph Böhmwalder <christoph@boehmwalder.at> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Karol Herbst <kherbst@redhat.com>
2018-02-02drm/nouveau/pmu/fuc: don't use movw directly anymoreKarol Herbst4-1292/+1292
Fixes failure to compile with recent envyas as a result of the 'movw' alias being removed for v5. A bit of history: v3 only has a 16-bit sign-extended immediate mov op. In order to set the high bits, there's a separate 'sethi' op. envyas validates that the value passed to mov(imm) is between -0x8000 and 0x7fff. In order to simplify macros that load both the low and high word, a 'movw' alias was added which takes an unsigned 16-bit immediate. However the actual hardware op still sign extends. v5 has a full 32-bit immediate mov op. The v3 16-bit immediate mov op is gone (loads 0 into the dst reg). However due to a bug in envyas, the movw alias still existed, and selected the no-longer-present v3 16-bit immediate mov op. As a result usage of movw on v5 is the same as mov with a 0x0 argument. The proper fix throughout is to only ever use the 'movw' alias in combination with 'sethi'. Anything else should get the sign-extended validation to ensure that the intended value ends up in the destination register. Changes in fuc3 binaries is the result of a different encoding being selected for a mov with an 8-bit value. v2: added commit message written by Ilia, thanks for that! v3: messed up rebasing, now it should apply Signed-off-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-02-01Merge tag 'drm-for-v4.16' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds7-50/+47
Pull drm updates from Dave Airlie: "This seems to have been a comparatively quieter merge window, I assume due to holidays etc. The "biggest" change is AMD header cleanups, which merge/remove a bunch of them. The AMD gpu scheduler is now being made generic with the etnaviv driver wanting to reuse the code, hopefully other drivers can go in the same direction. Otherwise it's the usual lots of stuff in i915/amdgpu, not so much stuff elsewhere. Core: - Add .last_close and .output_poll_changed helpers to reduce driver footprints - Fix plane clipping - Improved debug printing support - Add panel orientation property - Update edid derived properties at edid setting - Reduction in fbdev driver footprint - Move amdgpu scheduler into core for other drivers to use. i915: - Selftest and IGT improvements - Fast boot prep work on IPS, pipe config - HW workarounds for Cannonlake, Geminilake - Cannonlake clock and HDMI2.0 fixes - GPU cache invalidation and context switch improvements - Display planes cleanup - New PMU interface for perf queries - New firmware support for KBL/SKL - Geminilake HW workaround for perforamce - Coffeelake stolen memory improvements - GPU reset robustness work - Cannonlake horizontal plane flipping - GVT work amdgpu/radeon: - RV and Vega header file cleanups (lots of lines gone!) - TTM operation context support - 48-bit GPUVM support for Vega/RV - ECC support for Vega - Resizeable BAR support - Multi-display sync support - Enable swapout for reserved BOs during allocation - S3 fixes on Raven - GPU reset cleanup and fixes - 2+1 level GPU page table amdkfd: - GFX7/8 SDMA user queues support - Hardware scheduling for multiple processes - dGPU prep work rcar: - Added R8A7743/5 support - System suspend/resume support sun4i: - Multi-plane support for YUV formats - A83T and LVDS support msm: - Devfreq support for GPU tegra: - Prep work for adding Tegra186 support - Tegra186 HDMI support - HDMI2.0 and zpos support by using generic helpers tilcdc: - Misc fixes omapdrm: - Support memory bandwidth limits - DSI command mode panel cleanups - DMM error handling exynos: - drop the old IPP subdriver. etnaviv: - Occlusion query fixes - Job handling fixes - Prep work for hooking in gpu scheduler armada: - Move closer to atomic modesetting - Allow disabling primary plane if overlay is full screen imx: - Format modifier support - Add tile prefetch to PRE - Runtime PM support for PRG ast: - fix LUT loading" * tag 'drm-for-v4.16' of git://people.freedesktop.org/~airlied/linux: (1471 commits) drm/ast: Load lut in crtc_commit drm: Check for lessee in DROP_MASTER ioctl drm: fix gpu scheduler link order drm/amd/display: Demote error print to debug print when ATOM impl missing dma-buf: fix reservation_object_wait_timeout_rcu once more v2 drm/amdgpu: Avoid leaking PM domain on driver unbind (v2) drm/amd/amdgpu: Add Polaris version check drm/amdgpu: Reenable manual GPU reset from sysfs drm/amdgpu: disable MMHUB power gating on raven drm/ttm: Don't unreserve swapped BOs that were previously reserved drm/ttm: Don't add swapped BOs to swap-LRU list drm/amdgpu: only check for ECC on Vega10 drm/amd/powerplay: Fix smu_table_entry.handle type drm/ttm: add VADDR_FLAG_UPDATED_COUNT to correctly update dma_page global count drm: Fix PANEL_ORIENTATION_QUIRKS breaking the Kconfig DRM menuconfig drm/radeon: fill in rb backend map on evergreen/ni. drm/amdgpu/gfx9: fix ngg enablement to clear gds reserved memory (v2) drm/ttm: only free pages rather than update global memory count together drm/amdgpu: fix CPU based VM updates drm/amdgpu: fix typo in amdgpu_vce_validate_bo ...
2018-01-26Merge branch 'linux-4.15' of git://github.com/skeggsb/linux into drm-fixesDave Airlie1-15/+31
Single irq regression fix * 'linux-4.15' of git://github.com/skeggsb/linux: drm/nouveau: Move irq setup/teardown to pci ctor/dtor
2018-01-26drm/nouveau: Move irq setup/teardown to pci ctor/dtorLyude Paul1-15/+31
For a while we've been having issues with seemingly random interrupts coming from nvidia cards when resuming them. Originally the fix for this was thought to be just re-arming the MSI interrupt registers right after re-allocating our IRQs, however it seems a lot of what we do is both wrong and not even nessecary. This was made apparent by what appeared to be a regression in the mainline kernel that started introducing suspend/resume issues for nouveau: a0c9259dc4e1 (irq/matrix: Spread interrupts on allocation) After this commit was introduced, we started getting interrupts from the GPU before we actually re-allocated our own IRQ (see references below) and assigned the IRQ handler. Investigating this turned out that the problem was not with the commit, but the fact that nouveau even free/allocates it's irqs before and after suspend/resume. For starters: drivers in the linux kernel haven't had to handle freeing/re-allocating their IRQs during suspend/resume cycles for quite a while now. Nouveau seems to be one of the few drivers left that still does this, despite the fact there's no reason we actually need to since disabling interrupts from the device side should be enough, as the kernel is already smart enough to know to disable host-side interrupts for us before going into suspend. Since we were tearing down our IRQs by hand however, that means there was a short period during resume where interrupts could be received before we re-allocated our IRQ which would lead to us getting an unhandled IRQ. Since we never handle said IRQ and re-arm the interrupt registers, this would cause us to miss all of the interrupts from the GPU and cause our init process to start timing out on anything requiring interrupts. So, since this whole setup/teardown every suspend/resume cycle is useless anyway, move irq setup/teardown into the pci subdev's ctor/dtor functions instead so they're only called at driver load and driver unload. This should fix most of the issues with pending interrupts on resume, along with getting suspend/resume for nouveau to work again. As well, this probably means we can also just remove the msi rearm call inside nvkm_pci_init(). But since our main focus here is to fix suspend/resume before 4.15, we'll save that for a later patch. Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: Karol Herbst <kherbst@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Mike Galbraith <efault@gmx.de> Cc: stable@vger.kernel.org Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2018-01-23drm/nouveau/kms/nv50: Use drm_mode_get_hv_timing() to populate plane clip ↵Ville Syrjälä1-8/+12
rectangle Use drm_mode_get_hv_timing() to fill out the plane clip rectangle. No functional changes as the code already uses crtc_state->mode to populate the clip, which is also what drm_mode_get_hv_timing() uses. Once everyone agrees on this we can move the clip handling into drm_atomic_helper_check_plane_state(). Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: nouveau@lists.freedesktop.org Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-11-ville.syrjala@linux.intel.com Reviewed-by: Thierry Reding <treding@nvidia.com>
2018-01-19Merge branch 'linux-4.15' of git://github.com/skeggsb/linux into drm-fixesDave Airlie10-13/+114
Thought I'd try my luck getting one more in: - Two fixes for Tegra (one is to common code, but our userspace doesn't hit it). - One for NV5x-class MCPs * 'linux-4.15' of git://github.com/skeggsb/linux: drm/nouveau/mmu/mcp77: fix regressions in stolen memory handling drm/nouveau/bar/gk20a: Avoid bar teardown during init drm/nouveau/drm/nouveau: Pass the proper arguments to nvif_object_map_handle()
2018-01-19drm/nouveau/mmu/mcp77: fix regressions in stolen memory handlingBen Skeggs7-10/+109
- Fixes addition of stolen memory base address to PTEs. - Removes support for compression. Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Tested-by: Pierre Moreau <pierre.morrow@free.fr>
2018-01-19drm/nouveau/bar/gk20a: Avoid bar teardown during initJon Hunter2-2/+2
Commit bbb163e18960 ("drm/nouveau/bar: implement bar1 teardown") introduced add a teardown helper function for BAR1. During initialisation of the Nouveau, initially all the teardown helpers are called once, before calling their init counterparts. For gk20a, after the BAR1 teardown function is called, the device is hanging during the initialisation of the FB sub-device. At this point it is unclear why this is happening and this is still under investigation. However, this change is preventing Tegra124 devices from booting when Nouveau is enabled. To allow Tegra124 to boot, remove the teardown helper for gk20a. This is based upon a previous patch by Guillaume Tucker but limits the workaround to only gk20a GPUs. Fixes: bbb163e18960 ("drm/nouveau/bar: implement bar1 teardown") Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com> Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-08-26 04:32:30 +0000