| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
When the definition of this struct was removed a forward declaration and an
unused struct member were still left around. Remove them because they serve
no purpose.
Fixes 44b460cfe554 ("drm: imx: remove struct imx_drm_crtc and imx_drm_crtc_helper_funcs")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
If the second LVDS channel has been disabled in the DT when using dual-channel
mode we should not print a warning.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The LVDS signal integrity is only guaranteed when the correct enable
sequence (first IPU DI, then LDB) is used. If the LDB display output was
active before the imx-drm driver is loaded (like when a bootsplash was
active) the DI will be disabled by the full IPU reset we do when loading
the driver. The LDB control registers are not part of the IPU range and
thus will remain unchanged.
This leads to the LDB still being active when the DI is getting enabled,
effectively reversing the required enable sequence. Fix this by also
disabling the LDB on driver bind.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Again to align with the usual prefix of just drm_connector_. Again
done with sed + manual fixup for indent issues.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-7-daniel.vetter@ffwll.ch
|
|
Just makes it longer, and for most things in drm_connector.[hc] we
just use the drm_connector_ prefix. Done with sed + a bit of manual
fixup for the indenting.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-6-daniel.vetter@ffwll.ch
|
|
Use drm_plane_mask() where appropriate.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626194716.12522-6-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
|
|
Right now the vblank event completion is racing with the atomic update,
which is especially bad when the PRE is in use, as one of the hardware
issue workaround might extend the atomic commit for quite some time.
If the vblank IRQ happens to trigger during that time, we will prematurely
signal the atomic commit completion to userspace, which causes tearing
when userspace re-uses a framebuffer we haven't managed to flip away from
yet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
ipu_planes_assign_pre() prototype is in "imx-drm.h" header file, so
include it to fix the following sparse warning:
drivers/gpu/drm/imx/ipuv3-plane.c:729:5: warning: symbol 'ipu_planes_assign_pre' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
ipu_plane_state_reset(), ipu_plane_duplicate_state() and
ipu_plane_destroy_state() are only used in this file, so make them static.
This fixes the following sparse warnings:
drivers/gpu/drm/imx/ipuv3-plane.c:275:6: warning: symbol 'ipu_plane_state_reset' was not declared. Should it be static?
drivers/gpu/drm/imx/ipuv3-plane.c:295:24: warning: symbol 'ipu_plane_duplicate_state' was not declared. Should it be static?
drivers/gpu/drm/imx/ipuv3-plane.c:309:6: warning: symbol 'ipu_plane_destroy_state' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Move the plane clip rectangle handling into
drm_atomic_helper_check_plane_state(). Drivers no longer
have to worry about such mundane details.
v2: Convert armada, rcar, and sun4i as well
v3: Resolve simple_kms_helper conflict
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org> #msm
Link: https://patchwork.freedesktop.org/patch/msgid/20180123170857.13818-5-ville.syrjala@linux.intel.com
Acked-by: Liviu Dudau <liviu.dudau@arm.com> #hdlcd,malidp
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> #imx,mtk
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com> #vmwgfx
Acked-by: Neil Armstrong <narmstrong@baylibre.com> #meson
Acked-by: Shawn Guo <shawnguo@kernel.org> #zte
|
|
dw_hdmi shouldn't set drvdata since some drivers might need to store
it's own data there. Rework dw_hdmi in a way to return struct dw_hdmi
instead to store it in drvdata. This way drivers are responsible to
store and pass structure when needed.
Idea was taken from the following commit:
8242ecbd597d ("drm/bridge/synopsys: stop clobbering drvdata")
Cc: p.zabel@pengutronix.de
Cc: Laurent.pinchart@ideasonboard.com
Cc: hjc@rock-chips.com
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-6-jernej.skrabec@siol.net
|
|
Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.
Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-7-ville.syrjala@linux.intel.com
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.pengutronix.de/git/pza/linux into drm-next
drm/imx: format modifier support
- Add tiled prefetch support to PRE
- Add format modifier support to PRG and imx-drm-core
- Use runtime PM to control PRG clock
- Allow building ipu-v3 under COMPILE_TEST
* tag 'imx-drm-next-2018-01-02' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: allow to build with COMPILE_TEST
drm/imx: advertise supported plane format modifiers
drm/imx: add FB modifier support
gpu: ipu-v3: prg: add modifier support
gpu: ipu-v3: pre: add tiled prefetch support
gpu: ipu-v3: prg: switch to runtime PM
|
|
Let userspace know about the supported modifiers, to make automatic
selection of a proper modifier possible.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This adds FB modifier support for the Vivante single buffer tiled formats,
when the PRG/PRE engines are present.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Allow to pass through the modifier to the PRE unit and extend the
format check with the supported modifiers.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115142001.45358-8-noralf@tronnes.org
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
Cross-subsystem Changes:
- device tree doc for the Mitsubishi AA070MC01 and Tianma TM070RVHG71
panels (Lukasz Majewski) and for a 2nd endpoint on stm32 (Philippe Cornu)
Core Changes:
The most important changes are:
- Add drm_driver .last_close and .output_poll_changed helpers to reduce
fbdev emulation footprint in drivers (Noralf)
- Fix plane clipping in core and for vmwgfx (Ville)
Then we have a bunch of of improvement for print and debug such as the
addition of a framebuffer debugfs file. ELD connector, HDMI and
improvements. And a bunch of misc improvements, clean ups and style
changes and doc updates
[airlied: drop eld bits from amdgpu_dm]
Driver Changes:
- sii8620: filter unsupported modes and add DVI mode support (Maciej Purski)
- rockchip: analogix_dp: Remove unnecessary init code (Jeffy Chen)
- virtio, cirrus: add fb create_handle support to enable screenshots(Lepton Wu)
- virtio: replace reference/unreference with get/put (Aastha Gupta)
- vc4, gma500: Convert timers to use timer_setup() (Kees Cook)
- vc4: Reject HDMI modes with too high of clocks (Eric)
- vc4: Add support for more pixel formats (Dave Stevenson)
- stm: dsi: Rename driver name to "stm32-display-dsi" (Philippe Cornu)
- stm: ltdc: add a 2nd endpoint (Philippe Cornu)
- via: use monotonic time for VIA_WAIT_IRQ (Arnd Bergmann)
* tag 'drm-misc-next-2017-11-30' of git://anongit.freedesktop.org/drm/drm-misc: (96 commits)
drm/bridge: tc358767: add copyright lines
MAINTAINERS: change maintainer for Rockchip drm drivers
drm/vblank: Fix vblank timestamp debugs
drm/via: use monotonic time for VIA_WAIT_IRQ
dma-buf: Fix ifnullfree.cocci warnings
drm/printer: Add drm_vprintf()
drm/edid: Allow HDMI infoframe without VIC or S3D
video/hdmi: Allow "empty" HDMI infoframes
dma-buf/fence: Fix lock inversion within dma-fence-array
drm/sti: Handle return value of platform_get_irq_byname
drm/vc4: Add support for NV21 and NV61.
drm/vc4: Use .pixel_order instead of custom .flip_cbcr
drm/vc4: Add support for DRM_FORMAT_RGB888 and DRM_FORMAT_BGR888
drm: Move drm_plane_helper_check_state() into drm_atomic_helper.c
drm: Check crtc_state->enable rather than crtc->enabled in drm_plane_helper_check_state()
drm/vmwgfx: Try to fix plane clipping
drm/vmwgfx: Use drm_plane_helper_check_state()
drm/vmwgfx: Remove bogus crtc coords vs fb size check
gpu: gma500: remove unneeded DRIVER_LICENSE #define
drm: don't link DP aux i2c adapter to the hardware device node
...
|
|
drm_atomic_helper_wait_for_vblanks will go away in the future.
The new drm_atomic_helper_setup_commit in 4.15 expects that blocking commits
have completed flipping before the commit_tail returns. This must be ensured
by calling wait_for_vblanks or wait_for_flip_done, where flip_done might do
a less agressive wait, which is fine for imx-drm.
Fixes: 080de2e5be2d (drm/atomic: Check for busy planes/connectors before
setting the commit)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Pull more drm updates from Dave Airlie:
"Fixes/cleanups for rc1, non-desktop flags for VR
- remove the MSM dt-bindings file Rob managed to push in the previous
pull.
- add a property/edid quirk to denote HMD devices, I had these
hanging around for a few weeks and Keith had done some work on
them, they are fairly self contained and small, and only affect
people using HTC Vive VR headsets so far.
- amdgpu, tegra, tilcdc, fsl fixes
- some imx-drm cleanups I missed, these seemed pretty small, and no
reason to hold off.
I have one TTM regression fix (fixes bochs-vga in qemu) sitting
locally awaiting review I'll probably send that in a separate pull
request tomorrow"
* tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux: (33 commits)
dt-bindings: remove file that was added accidentally
drm/edid: quirk HTC vive headset as non-desktop. [v2]
drm/fb: add support for not enabling fbcon on non-desktop displays [v2]
drm: add connector info/property for non-desktop displays [v2]
drm/amdgpu: fix rmmod KCQ disable failed error
drm/amdgpu: fix kernel hang when starting VNC server
drm/amdgpu: don't skip attributes when powerplay is enabled
drm/amd/pp: fix typecast error in powerplay.
drm/tilcdc: Remove obsolete "ti,tilcdc,slave" dts binding support
drm/tegra: sor: Reimplement pad clock
Revert "drm/radeon: dont switch vt on suspend"
drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
drm/amd/powerplay: fix unfreeze level smc message for smu7
drm/amdgpu:fix memleak
drm/amdgpu:fix memleak in takedown
drm/amd/pp: fix dpm randomly failed on Vega10
drm/amdgpu: set f_mapping on exported DMA-bufs
drm/amdgpu: Properly allocate VM invalidate eng v2
drm/fsl-dcu: enable IRQ before drm_atomic_helper_resume()
drm/fsl-dcu: avoid disabling pixel clock twice on suspend
...
|
|
git://git.pengutronix.de/git/pza/linux into drm-next
drm/imx: various cleanups
- Switch to drm_*_get/put() helpers
- Use correct parallel-display connector enum: DPI instead of VGA
- Remove incorrect unit name from device tree binding documentation example
- Remove an unused variable
* tag 'imx-drm-next-2017-10-18' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: ipu-dc: Remove unused 'di' variable
dt-bindings: fsl-imx-drm: Remove incorrect "@di0" usage
drm/imx: parallel-display: use correct connector enum
drm/imx: switch to drm_*_get(), drm_*_put() helpers
|
|
drm_plane_helper_check_update() isn't a transitional helper, so let's
rename it to drm_atomic_helper_check_plane_state() and move it into
drm_atomic_helper.c.
v2: Fix the WARNs about plane_state->crtc matching crtc_state->crtc
Cc: Daniel Vetter <daniel@ffwll.ch>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171101201619.6175-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
drm_plane_helper_check_state()
drm_plane_helper_check_state() is supposed to do things the atomic way,
so it should not be inspecting crtc->enabled. Rather we should be
looking at crtc_state->enable.
We have a slight complication due to drm_plane_helper_check_update()
reusing drm_plane_helper_check_state() for non-atomic drivers. Thus
we'll have to pass the crtc_state in manally and construct a fake
crtc_state in drm_plane_helper_check_update().
v2: Fix the WARNs about plane_state->crtc matching crtc_state->crtc
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171101201558.6059-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The imx parrallel display exposes a, well, display parallel interface.
Use the correct enum, instead of disguising the thing as a VGA connector.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use drm_*_get() and drm_*_put() helpers instead of drm_*_reference()
and drm_*_unreference() helpers.
drm_*_reference() and drm_*_unreference() functions are just
compatibility alias for drm_*_get() and drm_*_put() and should not be
used by new code. So convert all users of compatibility functions to
use the new APIs.
Generated by: scripts/coccinelle/api/drm-get-put.cocci
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-next
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- DP SDP defines (Ville)
- polish for scdc helpers (Thierry Reding)
- fix lifetimes for connector/plane state across crtc changes (Maarten
Lankhorst).
- sparse fixes (Ville+Thierry)
- make legacy kms ioctls all interruptible (Maarten)
- push edid override into the edid helpers (out of probe helpers)
(Jani)
- DP ESI defines for link status (DK)
Driver Changes:
- drm-panel is now in drm-misc!
- minor panel-simple cleanups/refactoring by various folks
- drm_bridge_add cleanup (Inki Dae)
- constify a few i2c_device_id structs (Arvind Yadav)
- More patches from Noralf's fb/gem helper cleanup
- bridge/synopsis: reset fix (Philippe Cornu)
- fix tracepoint include handling in drivers (Thierry)
- rockchip: lvds support (Sandy Huang)
- move sun4i into drm-misc fold (Maxime Ripard)
- sun4i: refactor driver load + support TCON backend/layer muxing
(Chen-Yu Tsai)
- pl111: support more pl11x variants (Linus Walleij)
- bridge/adv7511: robustify probing/edid handling (Lars-Petersen
Clausen)
New hw support:
- S6E63J0X03 panel (Hoegeun Kwon)
- OTM8009A panel (Philippe CORNU)
- Seiko 43WVF1G panel (Marco Franchi)
- tve200 driver (Linus Walleij)
Plus assorted of tiny patches all over, including our first outreachy
patches from applicants for the winter round!
* tag 'drm-misc-next-2017-09-20' of git://anongit.freedesktop.org/git/drm-misc: (101 commits)
drm: add backwards compatibility support for drm_kms_helper.edid_firmware
drm: handle override and firmware EDID at drm_do_get_edid() level
drm/dp: DPCD register defines for link status within ESI field
drm/rockchip: Replace dev_* with DRM_DEV_*
drm/tinydrm: Drop driver registered message
drm/gem-fb-helper: Use debug message on gem lookup failure
drm/imx: Use drm_gem_fb_create() and drm_gem_fb_prepare_fb()
drm/bridge: adv7511: Constify HDMI CODEC platform data
drm/bridge: adv7511: Enable connector polling when no interrupt is specified
drm/bridge: adv7511: Remove private copy of the EDID
drm/bridge: adv7511: Properly update EDID when no EDID was found
drm/crtc: Convert setcrtc ioctl locking to interruptible.
drm/atomic: Convert pageflip ioctl locking to interruptible.
drm/legacy: Convert setplane ioctl locking to interruptible.
drm/legacy: Convert cursor ioctl locking to interruptible.
drm/atomic: Convert atomic ioctl locking to interruptible.
drm/atomic: Prepare drm_modeset_lock infrastructure for interruptible waiting, v2.
drm/tve200: Clean up panel bridging
drm/doc: Update todo.rst
drm/dp/mst: Sideband message transaction to power up/down nodes
...
|
|
drm_fb_cma_create() and drm_fb_cma_prepare_fb() are just wrappers now,
use drm_gem_fb_create() and drm_gem_fb_prepare_fb() directly.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1502631125-13557-11-git-send-email-noralf@tronnes.org
|
|
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.14 merge window.
I'm sending this early, as my continuing journey into fatherhood is
occurring really soon now, I'm going to be mostly useless for the next
couple of weeks, though I may be able to read email, I doubt I'll be
doing much patch applications or git sending. If anything urgent pops
up I've asked Daniel/Jani/Alex/Sean to try and direct stuff towards
you.
Outside drm changes:
Some rcar-du updates that touch the V4L tree, all acks should be in
place. It adds one export to the radix tree code for new i915 use
case. There are some minor AGP cleanups (don't see that too often).
Changes to the vbox driver in staging to avoid breaking compilation.
Summary:
core:
- Atomic helper fixes
- Atomic UAPI fixes
- Add YCBCR 4:2:0 support
- Drop set_busid hook
- Refactor fb_helper locking
- Remove a bunch of internal APIs
- Add a bunch of better default handlers
- Format modifier/blob plane property added
- More internal header refactoring
- Make more internal API names consistent
- Enhanced syncobj APIs (wait/signal/reset/create signalled)
bridge:
- Add Synopsys Designware MIPI DSI host bridge driver
tiny:
- Add Pervasive Displays RePaper displays
- Add support for LEGO MINDSTORMS EV3 LCD
i915:
- Lots of GEN10/CNL support patches
- drm syncobj support
- Skylake+ watermark refactoring
- GVT vGPU 48-bit ppgtt support
- GVT performance improvements
- NOA change ioctl
- CCS (color compression) scanout support
- GPU reset improvements
amdgpu:
- Initial hugepage support
- BO migration logic rework
- Vega10 improvements
- Powerplay fixes
- Stop reprogramming the MC
- Fixes for ACP audio on stoney
- SR-IOV fixes/improvements
- Command submission overhead improvements
amdkfd:
- Non-dGPU upstreaming patches
- Scratch VA ioctl
- Image tiling modes
- Update PM4 headers for new firmware
- Drop all BUG_ONs.
nouveau:
- GP108 modesetting support.
- Disable MSI on big endian.
vmwgfx:
- Add fence fd support.
msm:
- Runtime PM improvements
exynos:
- NV12MT support
- Refactor KMS drivers
imx-drm:
- Lock scanout channel to improve memory bw
- Cleanups
etnaviv:
- GEM object population fixes
tegra:
- Prep work for Tegra186 support
- PRIME mmap support
sunxi:
- HDMI support improvements
- HDMI CEC support
omapdrm:
- HDMI hotplug IRQ support
- Big driver cleanup
- OMAP5 DSI support
rcar-du:
- vblank fixes
- VSP1 updates
arcgpu:
- Minor fixes
stm:
- Add STM32 DSI controller driver
dw_hdmi:
- Add support for Rockchip RK3399
- HDMI CEC support
atmel-hlcdc:
- Add 8-bit color support
vc4:
- Atomic fixes
- New ioctl to attach a label to a buffer object
- HDMI CEC support
- Allow userspace to dictate rendering order on submit ioctl"
* tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux: (1074 commits)
drm/syncobj: Add a signal ioctl (v3)
drm/syncobj: Add a reset ioctl (v3)
drm/syncobj: Add a syncobj_array_find helper
drm/syncobj: Allow wait for submit and signal behavior (v5)
drm/syncobj: Add a CREATE_SIGNALED flag
drm/syncobj: Add a callback mechanism for replace_fence (v3)
drm/syncobj: add sync obj wait interface. (v8)
i915: Use drm_syncobj_fence_get
drm/syncobj: Add a race-free drm_syncobj_fence_get helper (v2)
drm/syncobj: Rename fence_get to find_fence
drm: kirin: Add mode_valid logic to avoid mode clocks we can't generate
drm/vmwgfx: Bump the version for fence FD support
drm/vmwgfx: Add export fence to file descriptor support
drm/vmwgfx: Add support for imported Fence File Descriptor
drm/vmwgfx: Prepare to support fence fd
drm/vmwgfx: Fix incorrect command header offset at restart
drm/vmwgfx: Support the NOP_ERROR command
drm/vmwgfx: Restart command buffers after errors
drm/vmwgfx: Move irq bottom half processing to threads
drm/vmwgfx: Don't use drm_irq_[un]install
...
|
|
git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm: lock scanout transfers for consecutive bursts
- Lock the IDMAC scanout channel for multiple back-to-back bursts if possible,
to improve memory bandwidth utilisation.
- Replace a few occurences of state->fb with the already existing local fb
variable in ipu_plane_atomic_update
* tag 'imx-drm-next-2017-07-18' of git://git.pengutronix.de/git/pza/linux:
drm/imx: lock scanout transfers for consecutive bursts
drm/imx: ipuv3-plane: use fb local variable instead of state->fb
|
|
Historically, only RGB framebuffers could be assigned to the primary
plane. This changed with universal plane support. Since no colorspace
conversion was set up for the IPUv3 full plane, assigning YUV frame
buffers to the primary plane caused incorrect output.
Fix this by enabling color space conversion also for the primary plane.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
|
|
This is the plumbing for supporting fb modifiers on planes. Modifiers
have already been introduced to some extent, but this series will extend
this to allow querying modifiers per plane. Based on this, the client to
enable optimal modifications for framebuffers.
This patch simply allows the DRM drivers to initialize their list of
supported modifiers upon initializing the plane.
v2: A minor addition from Daniel
v3:
* Updated commit message
* s/INVALID/DRM_FORMAT_MOD_INVALID (Liviu)
* Remove some excess newlines (Liviu)
* Update comment for > 64 modifiers (Liviu)
v4: Minor comment adjustments (Liviu)
v5: Some new platforms added due to rebase
v6: Add some missed plane inits (or maybe they're new - who knows at
this point) (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
|
|
This driver can use the drm_driver.dumb_destroy and
drm_driver.dumb_map_offset defaults, so no need to set them.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1500837417-40580-10-git-send-email-noralf@tronnes.org
|
|
Linux 4.13-rc2
This is required for drm-misc fixing.
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm: fix parallel display regression and typo in plane format list
- Fix a regression where the parallel-display driver would not probe
anymore if no panel is specified in the device tree, since the
introduction of drm_of_find_panel_or_bridge.
- Fix a typo in the plane format list: replace a duplicate BGRA8888 format
with BGRX8888, as originally intended.
* tag 'imx-drm-fixes-2017-07-18' of git://git.pengutronix.de/git/pza/linux:
drm/imx: parallel-display: Accept drm_of_find_panel_or_bridge failure
drm/imx: fix typo in ipu_plane_formats[]
|
|
The parallel panel driver should continue to work without having an
endpoint linking to an panel in DT for backwards compatibility.
With the recent switch to drm_of_find_panel_or_bridge, an absent
panel results in a failure with -ENODEV error return code. To restore
the old behaviour, ignore the -ENODEV return code.
Reported-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Fixes: ebc944613567 ("drm: convert drivers to use drm_of_find_panel_or_bridge")
Tested-by: Chris Healy <cphealy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The BGRA8888 appears twice in the ipu_plane_formats[] list. The
duplicate should be BGRX8888.
The original commit is:
commit 59d6b7189a96 ("drm/imx: ipuv3-plane: enable support for RGBX8888
and RGBA8888 pixel formats")
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@nxp.com>
Fixes: 59d6b7189a96 ("drm/imx: ipuv3-plane: enable support for RGBX8888 and RGBA8888 pixel")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Because of its shallow queues and limited reordering ability, the i.MX6Q
memory controller likes AXI bursts of consecutive addresses a lot.
To optimize memory access performance, lock the IPU scanout channels for
a number of burst accesses each, before switching to the next channel.
The burst size and length of a locked burst chain are chosen not to
overshoot the stride.
Enabling the 8-burst channel lock on a single 1920x1080@60Hz RGBx
scanout (474 MiB/s of 64-byte IPU memory read accesses) reduces the
reported memory controller busy cycles from 46% to below 28% on an
otherwise idle i.MX6Q.
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
We already have a local variable assigned to state->fb, use it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
for_each_obj_in_state is about to be removed, so use the new atomic
iterator macros.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20170712081344.25495-13-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The old state is useful for drivers that need to perform operations at
enable time that depend on the transition between the old and new
states.
While at it, rename the operation to .atomic_enable() to be consistent
with .atomic_disable(), as the .enable() operation is used by atomic
helpers only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-drm and mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> # for hdlcd and mali-dp
Acked-by: Stefan Agner <stefan@agner.ch> # for fsl-dcu
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-2-laurent.pinchart+renesas@ideasonboard.com
|
|
Linux 4.12-rc5 for nouveau fixes
|
|
Not having an endpoint bound in DT should not cause a failure here,
there are fallbacks. So explicitly accept a missing endpoint.
This behavior change was introduced by refactoring in drm_of parsing
code and it should not require dts changes.
In particular this fixes imx6qdl-sabreauto boards.
Link: https://lists.freedesktop.org/archives/dri-devel/2017-May/141233.html
Fixes: ebc944613567 ("drm: convert drivers to use drm_of_find_panel_or_bridge")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Now that we have a callback to check if bridge supports a given mode
we can use it in Synopsys Designware HDMI bridge so that we restrict
the number of probbed modes to the ones we can actually display.
Also, there is no need to use mode_fixup() callback as mode_valid()
will handle the mode validation.
NOTE: I also had to change the pdata declaration of mode_valid
custom callback so that the passed modes are const. I also changed
in the platforms I found. Not even compiled it though.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/3d8d449e4d13d2535fa292c75f5fa931de4a4fa8.1495720737.git.joabreu@synopsys.com
|
|
It's only done in the driver load error path, where vblanks don't need
to be quiescent anyway. And that's all drm_vblank_cleanup does, since
the core will release the vblank allocations on its own already. So
drop it.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170524145212.27837-24-daniel.vetter@ffwll.ch
|
|
Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ defines to the UAPI
as a convenience.
Ideally the DRM_ROTATE_ and DRM_REFLECT_ property ids are looked up
through the atomic API, but realizing that userspace is likely to take
shortcuts and assume that the enum values are what is sent over the
wire.
As a result these defines are provided purely as a convenience to
userspace applications.
Changes since v3:
- Switched away from past tense in comments
- Add define name change to previously mis-spelled DRM_REFLECT_X comment
- Improved the comment for the DRM_MODE_REFLECT_<axis> comment
Changes since v2:
- Changed define prefix from DRM_MODE_PROP_ to DRM_MODE_
- Fix compilation errors
- Changed comment formatting
- Deduplicated comment lines
- Clarified DRM_MODE_PROP_REFLECT_ comment
Changes since v1:
- Moved defines from drm.h to drm_mode.h
- Changed define prefix from DRM_ to DRM_MODE_PROP_
- Updated uses of the defines to the new prefix
- Removed include from drm_rect.c
- Stopped using the BIT() macro
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519205017.23307-2-robert.foss@collabora.com
|
