Age | Commit message (Collapse) | Author | Files | Lines |
|
Currently the driver only handles panel directly connected to the DPI output.
Handle the case where a bridge is connected past DPI output of this bridge.
This could be e.g. DPI to LVDS encoder chip.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220724224317.288727-1-marex@denx.de
|
|
1. Support HDMI_I2S audio format.
2. Return 0 if there is no sink connection in .hw_param callback.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Acked-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Jiaxin Yu<jiaxin.yu@mediatek.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220726033058.403715-1-xji@analogixsemi.com
|
|
The ICN6211 is capable of deriving its internal PLL clock from either
MIPI DSI HS clock, external REFCLK clock, or even internal oscillator.
Currently supported is only the first option. Add support for external
REFCLK clock input in addition to that.
There is little difference between these options, except that in case
of MIPI DSI HS clock input, the HS clock are pre-divided by a fixed /4
divider before being fed to the PLL input, while in case of external
REFCLK, the RECLK clock are fed directly into the PLL input.
Per exceptionally poor documentation, the REFCLK must be in range of
10..154 MHz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220801131747.183041-2-marex@denx.de
|
|
Fill in hs_rate and lp_rate to struct mipi_dsi_device for this bridge and
adjust DSI input frequency calculations such that they expect the DSI host
to configure HS clock according to hs_rate.
This is an optimization for the DSI burst mode case. In case the DSI device
supports DSI burst mode, it is recommended to operate the DSI interface at
the highest possible HS clock frequency which the DSI device supports. This
permits the DSI host to send as short as possible bursts of data on the DSI
link and keep the DSI data lanes in LP mode otherwise, which reduces power
consumption.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220801131555.182969-1-marex@denx.de
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
One patch for imx/dcss to get rid of a warning message, one off-by-one
fix and GA103 support for nouveau, a refcounting fix for meson, a NULL
pointer dereference fix for ttm, a error check fix for lvds-codec, a
dt-binding schema fix and an underflow fix for sun4i
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220816094401.wtadc7ddr6lzq6aj@houat
|
|
Backmerging for v6.0-rc1.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Disable the main link PHYs and put them into reset when the main link
is disabled. When the PHYs stay enabled while the rest of the DP link
circuits are disabled there is some noise on the data lanes, which some
displays try to lock onto, waking them up from their low power state.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706132812.2171250-3-l.stach@pengutronix.de
|
|
The current CLRSIPO count is marginal and does not work with high
DSI clock rates. Increase it a bit to allow the DSI link to work at
up to 1Gbps lane speed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706132812.2171250-2-l.stach@pengutronix.de
|
|
There is no need to enforce a specific sync signal polarity on the
DPI interface, as we can simply tell the TC358767 which polarities
it should expect on the input interface.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706132812.2171250-1-l.stach@pengutronix.de
|
|
The drm_of_lvds_get_data_mapping() returns either negative value on
error or MEDIA_BUS_FMT_* otherwise. The check for 'ret' would also
catch the positive case of MEDIA_BUS_FMT_* and lead to probe failure
every time 'data-mapping' DT property is specified.
Fixes: 7c4dd0a266527 ("drm: of: Add drm_of_lvds_get_data_mapping")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220801125419.167562-1-marex@denx.de
|
|
A NULL check for bridge->encoder shows that it may be NULL, but it
already been dereferenced on all paths leading to the check.
812 if (!bridge->encoder) {
Dereference the pointer bridge->encoder.
810 drm_connector_attach_encoder(<9611->connector, bridge->encoder);
Signed-off-by: Zeng Jingxiang <linuszeng@tencent.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220727073119.1578972-1-zengjx95@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"As the diffstat shows, we've had lots of developments in a wide range
at this time; the majority of changes are about ASoC, including
subsystem-wide cleanups, continued SOF / Intel updates and a bunch of
new drivers (as usual), while there have been some significant (but
almost invisible) improvements in ALSA core side, too.
Below are some highlights:
Core:
- Faster lookups of control elements with Xarray; normal user won't
notice, but on the devices with tons of control elements, it can be
visibly faster
- Support for input validation for controls; this will harden for
badly written drivers in general with a slight overhead
- Deferred async signal handling for working around the potential
deadlocks
- Cleanup / refactoring raw MIDI locking code
ASoC:
- Restructing of the set_fmt() callbacks for making things clearer in
situations like CODEC to CODEC links
- Clean up and modernizing the DAI naming scheme setups
- Merge of more of the Intel AVS driver stack, including some board
integrations
- New version 4 mechanism for communication with SOF DSPs
- Suppoort for dynamically selecting the PLL to use at runtime on
i.MX platforms
- Improvements for CODEC to CODEC support in the generic cards
- Support for AMD Jadeite and various machines, AMD RPL, Intel
MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra
MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and
WAS883x, and Texas Instruments TAS2780
HD- and USB-audio:
- Continued improvement for CS35L41 (sub)codec support
- More quirks for various devices (HP, Lenovo, Dell, Clevo)"
* tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (778 commits)
ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx
ALSA: line6: Replace sprintf() with sysfs_emit()
ALSA: hda: Replace sprintf() with sysfs_emit()
ALSA: pcm: Replace sprintf() with sysfs_emit()
ALSA: core: Replace scnprintf() with sysfs_emit()
ALSA: control-led: Replace sprintf() with sysfs_emit()
ALSA: aoa: Replace sprintf() with sysfs_emit()
ALSA: ac97: Replace sprintf() with sysfs_emit()
ALSA: hda/realtek: Add quirk for Clevo NV45PZ
ALSA: hda/realtek: Add quirk for Lenovo Yoga9 14IAP7
ALSA: control: Use deferred fasync helper
ALSA: pcm: Use deferred fasync helper
ALSA: timer: Use deferred fasync helper
ALSA: core: Add async signal helpers
ASoC: q6asm: use kcalloc() instead of kzalloc()
ACPI: scan: Add CLSA0101 Laptop Support
ALSA: hda: cs35l41: Support CLSA0101
ALSA: hda: cs35l41: Use the CS35L41 HDA internal define
ASoC: dt-bindings: use spi-peripheral-props.yaml
ASoC: codecs: va-macro: use fsgen as clock
...
|
|
If devm_drm_of_get_bridge() can't find the connected bridge, it returns an
ERR_PTR(-EPROBE_DEFER) to indicate that the probe should be deferred.
But this path also prints an error message, which pollutes the kernel log
since is printed on every probe deferral, i.e:
$ dmesg | grep "failed to create panel bridge" | wc -l
38
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220722074755.660258-1-javierm@redhat.com
|
|
The datasheet says that VDD12 must be enabled and at full voltage before
VDD33 is enabled.
Reorder the bulk regulator supply names so that VDD12 is enabled before
VDD33. Any enable ramp delays should be handled by setting proper
constraints on the regulators.
Fixes: bc1aee7fc8f0 ("drm/bridge: Add I2C based driver for ps8640 bridge")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220721092258.3397461-1-wenst@chromium.org
|
|
Now as the driver does not depend on pdata->connector, add support for
attaching the bridge with DRM_BRIDGE_ATTACH_NO_CONNECTOR.
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220711092117.360797-3-dmitry.baryshkov@linaro.org
|
|
Rather than reading the pdata->connector directly, fetch the connector
using drm_atomic_state. This allows us to make pdata->connector optional
(and thus supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR).
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220711092117.360797-2-dmitry.baryshkov@linaro.org
|
|
In tc_probe_bridge_endpoint(), we should call of_node_put() when
breaking out of the for_each_endpoint_of_node() which will automatically
increase and decrease the refcount.
Fixes: 71f7d9c03118 ("drm/bridge: tc358767: Detect bridge mode from connected endpoints in DT")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220719065447.1080817-2-windhl@126.com
|
|
In anx7625_parse_dt(), 'pdata->mipi_host_node' will be assigned a
new reference with of_graph_get_remote_node() which will increase
the refcount of the object, correspondingly, we should call
of_node_put() for the old reference stored in the 'pdata->mipi_host_node'.
Fixes: 8bdfc5dae4e3 ("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220719065447.1080817-1-windhl@126.com
|
|
Speed up video clock calculation and remove redundant video debug message.
Signed-off-by: Pin-Yen Lin <treapking@chromium.org>
Signed-off-by: Allen Chen <allen.chen@ite.com.tw>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220715024910.12578-4-allen.chen@ite.com.tw
|
|
Use i2c bus to read/write when it6505 power off will occur i2c error.
Add this check will prevent i2c error when it6505 power off.
Signed-off-by: Pin-Yen Lin <treapking@chromium.org>
Signed-off-by: Allen Chen <allen.chen@ite.com.tw>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220715024910.12578-3-allen.chen@ite.com.tw
|
|
Change power sequence to meet it6505 data sheet requirement when boot on.
Signed-off-by: Pin-Yen Lin <treapking@chromium.org>
Signed-off-by: Allen Chen <allen.chen@ite.com.tw>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220715024910.12578-2-allen.chen@ite.com.tw
|
|
Send DPCD DP_SET_POWER_D0 command to the monitor in .atomic_enable
callback. Without this command, some monitors won't show up again after
changing the resolution.
Fixes: 46ca7da7f1e8 ("drm/bridge: it6505: Send DPCD SET_POWER to downstream")
Signed-off-by: Pin-Yen Lin <treapking@chromium.org>
Reviewed-by: Allen Chen <allen.chen@ite.com.tw>
Fixes: 46ca7da7f1e8 ("drm/bridge: it6505: Send DPCD SET_POWER to downstream")
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220714173715.v2.1.I85af54e9ceda74ec69f661852825845f983fc343@changeid
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v5.20
This is a big release thus far and there will probably be more changes
to come, it's a combination of a larger than usual crop of new drivers
and some subsysetm wide cleanups from Charles rather than anything
structural. The SOF and Intel DSP code both also continue to be very
actively developed.
- Restructing of the set_fmt() callbacks to be specified in terms of
the device rather than with semantics depending on if the device is
supposed to be a CODEC or SoC, making things clearer in situations
like CODEC to CODEC links.
- Clean up of the way we flag which DAI naming scheme we use to reflect
the progress that's been made modernising things.
- Merge of more of the Intel AVS driver stack, including some board
integrations.
- New version 4 mechanism for communication with SOF DSPs.
- Suppoort for dynamically selecting the PLL to use at runtime on i.MX
platforms.
- Improvements for CODEC to CODEC support in the generic cards.
- Support for AMD Jadeite and various machines, Intel MetorLake DSPs,
Mediatek MT8186 DSPs and MT6366, nVidia Tegra MDDRC, OPE and PEQ, NXP
TFA9890, Qualcomm SDM845, WCD9335 and WAS883x, and Texas Instruments
TAS2780.
|
|
Unlike what can be found for other DRM entities, we don't have a
DRM-managed function equivalent to devm_drm_of_get_bridge().
Let's create it.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-12-maxime@cerno.tech
|
|
Unlike what can be found for other entities, there's no DRM-managed
function to create a panel_bridge instance from a panel.
Let's introduce one.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-11-maxime@cerno.tech
|
|
All implementations return 0 and the return value of mipi_dsi_drv_remove()
is ignored anyhow.
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220708094922.1408248-4-u.kleine-koenig@pengutronix.de
|
|
cec_unregister_adapter() assumes that the underlying adapter ops are
callable. For example, if the CEC adapter currently has a valid physical
address, then the unregistration procedure will invalidate the physical
address by setting it to f.f.f.f. Whence the following kernel oops
observed after removing the adv7511 module:
Unable to handle kernel execution of user memory at virtual address 0000000000000000
Internal error: Oops: 86000004 [#1] PREEMPT_RT SMP
Call trace:
0x0
adv7511_cec_adap_log_addr+0x1ac/0x1c8 [adv7511]
cec_adap_unconfigure+0x44/0x90 [cec]
__cec_s_phys_addr.part.0+0x68/0x230 [cec]
__cec_s_phys_addr+0x40/0x50 [cec]
cec_unregister_adapter+0xb4/0x118 [cec]
adv7511_remove+0x60/0x90 [adv7511]
i2c_device_remove+0x34/0xe0
device_release_driver_internal+0x114/0x1f0
driver_detach+0x54/0xe0
bus_remove_driver+0x60/0xd8
driver_unregister+0x34/0x60
i2c_del_driver+0x2c/0x68
adv7511_exit+0x1c/0x67c [adv7511]
__arm64_sys_delete_module+0x154/0x288
invoke_syscall+0x48/0x100
el0_svc_common.constprop.0+0x48/0xe8
do_el0_svc+0x28/0x88
el0_svc+0x1c/0x50
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x15c/0x160
Code: bad PC value
---[ end trace 0000000000000000 ]---
Protect against this scenario by unregistering i2c_cec after
unregistering the CEC adapter. Duly disable the CEC clock afterwards
too.
Fixes: 3b1b975003e4 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220612144854.2223873-3-alvin@pqrs.dk
|
|
The ADV7511_REG_CEC_CTRL = 0xE2 register is part of the main register
map - not the CEC register map. As such, we shouldn't apply an offset to
the register address. Doing so will cause us to address a bogus register
for chips with a CEC register map offset (e.g. ADV7533).
Fixes: 3b1b975003e4 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220612144854.2223873-2-alvin@pqrs.dk
|
|
Move away from the deprecated enable/disable operations in
drm_bridge_funcs and enable atomic use.
v3:
- Drop use of DRM_BRIDGE_STATE_OPS
v2:
- fix build (kernel test robot <lkp@intel.com>)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Kieran Bingham <kieran.bingham@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220703202724.9553-2-sam@ravnborg.org
|
|
When LVDS dual link is used, we have to enable the LDB_CTRL_SPLIT_MODE bit.
Fixes: 463db5c2ed4a ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220701065634.4027537-3-victor.liu@nxp.com
Link: https://patchwork.freedesktop.org/patch/msgid/20220701065634.4027537-4-victor.liu@nxp.com
|
|
With LVDS dual link, up to 160MHz mode clock rate is supported.
With LVDS single link, up to 80MHz mode clock rate is supported.
Fix mode clock rate validation by swapping the maximum mode clock
rates of the two link modes.
Fixes: 463db5c2ed4a ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220701065634.4027537-2-victor.liu@nxp.com
|
|
The DE inversion is implemented in LCDIFv3 driver and is no longer
needed in the LDB bridge which does not invert the DE signal. Drop
the inversion.
Fixes: 463db5c2ed4ae ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630174031.92354-1-marex@denx.de
|
|
Move hpd polling check into wait_hpd_asserted() callback. For the cases
that aux transfer function wasn't used, do hpd polling check after pm
runtime resume, which will power on the bridge.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-5-hsinyi@chromium.org
|
|
Move devm_of_dp_aux_populate_ep_devices() after pm runtime and i2c setup
to avoid NULL pointer crash.
edp-panel probe (generic_edp_panel_probe) calls pm_runtime_get_sync() to
read EDID. At this time, bridge should have pm runtime enabled and i2c
clients ready.
Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-4-hsinyi@chromium.org
|
|
There's no need to check for IRQ or disable it in suspend.
Use pm_runtime_force_suspend(resume) to make sure anx7625 is powered off
correctly. Make the system suspend/resume and pm runtime suspend/resume
more consistent.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-3-hsinyi@chromium.org
|
|
Simplify the resource management.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-2-hsinyi@chromium.org
|
|
drm_crtc.h has no need for linux/i2c.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching linux/i2c.h.
Quite a few placs do currently depend on linux/i2c.h without
actually including it directly. All of those need to be
fixed up.
v2: imx and mcde need linux/io.h for readl()/etc.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-5-ville.syrjala@linux.intel.com
|
|
drm_crtc.h has no need for linux/media-bus-format.h, so don't
include it. Avoids useless rebuilds of the entire universe when
touching linux/media-bus-format.h.
Quite a few placs do currently depend on linux/media-bus-format.h
without actually including it directly. All of those need to be
fixed up.
v2: Deal with ingenic as well
v3: Fix up mxsfb and remaining parts of imx
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-4-ville.syrjala@linux.intel.com
|
|
drm_crtc.h has no need for linux/fb.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching linux/fb.h.
Quite a few placs do currently depend on linux/fb.h or other
headers pulled in by it without actually including any of it
directly. All of those need to be fixed up.
v2: Split the vmwgfx change out
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-3-ville.syrjala@linux.intel.com
|
|
The next call to sii8620_burst_get_tx_buf will result in off-by-one
When ctx->burst.tx_count + size == ARRAY_SIZE(ctx->burst.tx_buf). The same
thing happens in sii8620_burst_get_rx_buf.
This patch also change tx_count and tx_buf to rx_count and rx_buf in
sii8620_burst_get_rx_buf. It is unreasonable to check tx_buf's size and
use rx_buf.
Fixes: e19e9c692f81 ("drm/bridge/sii8620: add support for burst eMSC transmissions")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220518065856.18936-1-hbh25y@gmail.com
|
|
It's unnecessary to invert input data enable signal polarity
according to the output one. Let's drop the inversion.
Since ->atomic_check() does nothing more than the inversion,
it can be dropped entirely as well.
Without this patch, 'koe,tx26d202vm0bwa' LVDS panel connected
with i.MX8MP EVK board does not show any data on screen.
Fixes: 463db5c2ed4a ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220701065634.4027537-4-victor.liu@nxp.com
|
|
When LVDS dual link is used, we have to enable the LDB_CTRL_SPLIT_MODE bit.
Fixes: 463db5c2ed4a ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220701065634.4027537-3-victor.liu@nxp.com
|
|
With LVDS dual link, up to 160MHz mode clock rate is supported.
With LVDS single link, up to 80MHz mode clock rate is supported.
Fix mode clock rate validation by swapping the maximum mode clock
rates of the two link modes.
Fixes: 463db5c2ed4a ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220701065634.4027537-2-victor.liu@nxp.com
|
|
The various Freescale i.MX8 display bridges are only present on
Freescale i.MX8 SoCs. Hence add a dependency on ARCH_MXC, to prevent
asking the user about these drivers when configuring a kernel without
i.MX SoC support.
Fixes: e60c4354840b2fe8 ("drm/bridge: imx: Add LDB support for i.MX8qm")
Fixes: 3818715f62b42b5c ("drm/bridge: imx: Add LDB support for i.MX8qxp")
Fixes: 96988a526c97cfbe ("drm/bridge: imx: Add i.MX8qxp pixel link to DPI support")
Fixes: 1ec17c26bc06289d ("drm/bridge: imx: Add i.MX8qm/qxp display pixel link support")
Fixes: 93e163a9e0392aca ("drm/bridge: imx: Add i.MX8qm/qxp pixel combiner support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/42c542b53a1c8027b23a045045fbb7b34479913d.1656072500.git.geert+renesas@glider.be
|
|
The DSI lane count can be accessed via the dsi device pointer,
make use of that. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220624181902.151959-1-marex@denx.de
|
|
As mipi_dsi_driver_register could return error if fails,
it should be better to check the return value and return error
if fails.
Moreover, if i2c_add_driver fails, mipi_dsi_driver_register
should be reverted.
Fixes: 1e4d58cd7f88 ("drm/bridge: adv7533: Create a MIPI DSI device")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220602103401.2980938-1-jiasheng@iscas.ac.cn
|
|
backlight_properties.fb_blank is deprecated. The states it represents
are handled by other properties; but instead of accessing those
properties directly, drivers should use the helpers provided by
backlight.h.
Instead of retrieving the backlight brightness in struct
backlight_properties manually, and then checking whether the backlight
should be on at all, use backlight_get_brightness() which does all
this and insulates this from future changes.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220607181022.1119546-1-steve@sk2.org
|
|
This implements the callback added by the patch ("drm/dp: Add
wait_hpd_asserted() callback to struct drm_dp_aux").
With this change and all the two "DP AUX Endpoint" drivers changed to
use wait_hpd_asserted(), we no longer need to have an long delay in
the AUX transfer function. It's up to the panel code to make sure that
the panel is powered now. If someone tried to call the aux transfer
function without making sure the panel is powered we'll just get a
normal transfer failure.
We'll still keep the wait for HPD in the pre_enable() function. Though
it's probably not actually needed there, this driver is used in the
old mode (pre-DP AUX Endpoints) and it may be important for those
cases. If nothing else, it shouldn't cause any big problems.
NOTE: When handling the timeout for HPD we start the timer _after_
we've runtime resumed the device. This is definitely important for the
panel on my homestar which comes up 170 ms after we start timing (the
panel specifies 200 ms max). It's a little unclear how much of this
extra time is due to some internal state machine in the parade
firmware vs. debouncing but it seems to work for the two test cases I
have to do it this way.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614145327.v4.4.Ie827321ce263be52fdb8c1276f6f8cc00d78029f@changeid
|
|
Panel orientation property should be set before drm_dev_register().
Some drm driver calls drm_dev_register() in .bind(). However, most
panels sets orientation property relatively late, mostly in .get_modes()
callback, since this is when they are able to get the connector and
binds the orientation property to it, though the value should be known
when the panel is probed.
In drm_bridge_connector_init(), if a bridge is a panel bridge, use it to
set the connector's panel orientation property.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[dianders: fixed space vs. tab indentation]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220609072722.3488207-9-hsinyi@chromium.org
|