| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
|
|
According to the reference manual level interrupts can't be acked
using the IRQSTAT registers. The effect is that when a level interrupt
triggers the following ack is a no-op and the same interrupt triggers
again right after it has been unmasked after running the interrupt
handler.
The reference manual says:
Status bits for pins configured as level sensitive interrupts cannot be
cleared unless either the actual pin is in the non-interrupting state, or
the pin has been disabled as an interrupt source by clearing its bit in
HW_PINCTRL_PIN2IRQ.
To work around the duplicated interrupts we can use the PIN2IRQ
rather than the IRQEN registers to mask the interrupts. This
probably does not work for the edge interrupts, so we have to split up
the irq chip into two chip types, one for the level interrupts and
one for the edge interrupts. We now make use of two different enable
registers, so we have to take care to always enable the right one,
especially during switching of the interrupt type. An easy way
to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which
makes sure that set_irq_type is called with masked interrupts. With this
the flow to change the irq type is like:
- core masks interrupt (using the current chip type)
- mxs_gpio_set_irq_type() changes chip type if necessary
- mxs_gpio_set_irq_type() unconditionally sets the enable bit in the
now unused enable register
- core eventually unmasks the interrupt (using the new chip type)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The mxs gpio controller does not only have a mask register to mask
interrupts, but also enable/disable registers. Use the enable/disable
registers rather than the mask register. This does not have any
advantage for now, but makes the next patch simpler.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that we have the new helper function that sets nice names for GPIO
lines based on "gpio-line-names" device property, we can take advantage of
this in acpi_gpiochip_add().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to use "gpio-line-names" property in systems not having DT as
their boot firmware, rework of_gpiochip_set_names() to use device property
accessors. This reworked function is placed in a separate file making it
clear it deals with universal device properties.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIO hogging means that the GPIO controller can "hog" and configure certain
GPIOs without need for a driver or userspace to do that. This is useful in
open-connected boards where BIOS cannot possibly know beforehand which
devices will be connected to the board.
This adds GPIO hogging mechanism to ACPI analogous to Device Tree.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Make it possible to have an empty GPIOs in a GPIO list for device. For
example a SPI master may use both GPIOs and native pins as chip selects and
we need to be able to distinguish between the two.
This makes it mandatory to have exactly 3 arguments for GPIOs and then
converts gpiolib to use of __acpi_node_get_property_reference() instead. In
addition we make acpi_gpio_package_count() to handle holes as well (this
matches the DT version).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add compatible string for the MAX7318 part. This is a two bank,
16 lines, I2C GPIO expander with interrupt line.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
All the boards supported by the gpio-ts4900 driver are i.MX6 boards,
so only offer the driver for building on this platform, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the GPIO functionality for the Altera Arria10 MAX5 System Resource
Chip. The A10 MAX5 has 12 bits of GPIO assigned to switches, buttons,
and LEDs as a GPIO extender on the SPI bus.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>i
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Current code does not use gpio_irq/irq_base/gpio_base fields from
struct max77620_gpio, so remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b0e
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
From the beginning of the gpio-mpc8xxx.c, the "handle_level_irq"
has being used to handle GPIO interrupts in the PowerPC/Layerscape
platforms. But actually, almost all PowerPC/Layerscape platforms
assert an interrupt request upon either a high-to-low change or
any change on the state of the signal.
So the "handle_level_irq" is not reasonable for PowerPC/Layerscape
GPIO interrupt, it should be "handle_edge_irq". Otherwise the system
may lost some interrupts from the PIN's state changes.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/gpio/gpio-ath79.ko | grep alias
$
After this patch:
$ modinfo drivers/gpio/gpio-ath79.ko | grep alias
alias: of:N*T*Cqca,ar9340-gpioC*
alias: of:N*T*Cqca,ar9340-gpio
alias: of:N*T*Cqca,ar7100-gpioC*
alias: of:N*T*Cqca,ar7100-gpio
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Aban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/gpio/gpio-ts4800.ko | grep alias
$
After this patch:
$ modinfo drivers/gpio/gpio-ts4800.ko | grep alias
alias: of:N*T*Ctechnologic,ts4800-gpioC*
alias: of:N*T*Ctechnologic,ts4800-gpio
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO_GET_LINEEVENT_IOCTL currently ignores unknown or undefined
linehandle and lineevent flags. From a backwards and forwards compatibility
viewpoint it is highly desirable to reject unknown flags though.
On one hand an application that is using newer flags and is running on
an older kernel has no way to detect if the new flags were handled
correctly if they are silently discarded.
On the other hand an application that (accidentally) passes undefined flags
will run fine on an older kernel, but may break on a newer kernel when
these flags get defined.
Ensure that requests that have undefined flags set are rejected with an
error, rather than silently discarding the undefined flags.
Cc: stable@vger.kernel.org
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO_GET_LINEHANDLE_IOCTL currently ignores unknown or undefined
linehandle flags. From a backwards and forwards compatibility viewpoint it
is highly desirable to reject unknown flags though.
On one hand an application that is using newer flags and is running on
an older kernel has no way to detect if the new flags were handled
correctly if they are silently discarded.
On the other hand an application that (accidentally) passes undefined flags
will run fine on an older kernel, but may break on a newer kernel when
these flags get defined.
Ensure that requests that have undefined flags set are rejected with an
error, rather than silently discarding the undefined flags.
Cc: stable@vger.kernel.org
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIOHANDLE_GET_LINE_VALUES_IOCTL handler allocates a gpiohandle_data
struct on the stack and then passes it to copy_to_user(). But depending on
the number of requested line handles the struct is only partially
initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Cc: stable@vger.kernel.org
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The line offset that is used as an index into the descs array is provided
by userspace and might go beyond the bounds of the array. If that happens
undefined behavior will occur.
Make sure that the offset is within the bounds of the desc array and reject
any requests that specify a value outside of it.
Cc: stable@vger.kernel.org
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIOHANDLE_GET_LINE_VALUES_IOCTL handler allocates a gpiohandle_data
struct on the stack and then passes it to copy_to_user(). But only the
first element of the values array in the struct is set, which leaves the
struct partially initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Cc: stable@vger.kernel.org
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The line offset that is used as an index into the descs array is provided
by userspace and might go beyond the bounds of the array. If that happens
undefined behavior will occur.
Make sure that the offset is within the bounds of the desc array and reject
any requests that specify a value outside of it.
Cc: stable@vger.kernel.org
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO_GET_CHIPINFO_IOCTL handler allocates a gpiochip_info struct on the
stack and then passes it to copy_to_user(). But depending on the length of
the GPIO chip name and label the struct is only partially initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Cc: stable@vger.kernel.org
Fixes: 521a2ad6f862 ("gpio: add userspace ABI for GPIO line information")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current line offset validation is off by one. Depending on the data
stored behind the descs array this can either cause undefined behavior or
disclose arbitrary, potentially sensitive, memory to the issuing userspace
application.
Make sure that offset is within the bounds of the desc array.
Cc: stable@vger.kernel.org
Fixes: 521a2ad6f862 ("gpio: add userspace ABI for GPIO line information")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
acpi_dev_gpio_irq_get() currently ignores the error returned
by acpi_get_gpiod_by_index() and overwrites it with -ENOENT.
Problem is this error can be -EPROBE_DEFER, which just blows
up some drivers when the module ordering is not correct.
Cc: stable@vger.kernel.org
Signed-off-by: David Arcari <darcari@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Building the gpio-mockup driver without SYSFS results in a harmless Kconfig
warning:
warning: (GPIO_MOCKUP) selects GPIO_SYSFS which has unmet direct dependencies (GPIOLIB && SYSFS)
We can easily avoid that warning by adding a dependency on SYSFS.
Fixes: 0f98dd1b27d2 ("gpio/mockup: add virtual gpio device")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
&& was obviously intended here.
Fixes: 6936e1f88d23 ('gpio: stmpe: Write int status register only when needed')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Free memory mapping, if mxs_gpio_probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a follow-up to commit 559b46990e76 ("gpio: pca953x: fix an
incorrect lockdep warning"). The reason for calling
lockdep_set_subclass() in pca953x_probe() is not explained in
the code.
Add a comment describing the problem, partial solution and required
future extensions.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Here is the 4.9 pull request from I2C including:
- centralized error messages when registering to the core
- improved lockdep annotations to prevent false positives
- DT support for muxes, gates, and arbitrators
- bus speeds can now be obtained from ACPI
- i2c-octeon got refactored and now supports ThunderX SoCs, too
- i2c-tegra and i2c-designware got a bigger bunch of updates
- a couple of standard driver fixes and improvements"
* 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits)
i2c: axxia: disable clks in case of failure in probe
i2c: octeon: thunderx: Limit register access retries
i2c: uniphier-f: fix misdetection of incomplete STOP condition
gpio: pca953x: variable 'id' was used twice
i2c: i801: Add support for Kaby Lake PCH-H
gpio: pca953x: fix an incorrect lockdep warning
i2c: add a warning to i2c_adapter_depth()
lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
i2c: export i2c_adapter_depth()
i2c: rk3x: Fix variable 'min_total_ns' unused warning
i2c: rk3x: Fix sparse warning
i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
i2c: octeon: Fix high-level controller status check
i2c: octeon: Avoid sending STOP during recovery
i2c: octeon: Fix set SCL recovery function
i2c: rcar: add support for r8a7796 (R-Car M3-W)
i2c: imx: make bus recovery through pinctrl optional
i2c: meson: add gxbb compatible string
i2c: uniphier-f: set the adapter to master mode when probing
i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
|
|
of_get_named_gpiod_flags() was missing a static inline version
when compiling without OF_GPIO. Add this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
of_gpiochip_add() and of_gpiochip_remove() are only used locally
in the gpio subsystem so move these functions to the local
header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The generic GPIO library directly implement code for acpi_find_gpio()
which is only used with CONFIG_ACPI. This was probably done because
OF did the same thing, but I removed that so remove this too.
Rename the internal acpi_find_gpio() in gpiolib-acpi.c to
acpi_populate_gpio_lookup() which seems to be more appropriate anyway
so as to avoid a namespace clash with the same function.
Make the stub return -ENOENT rather than -ENOSYS (as that is for
syscalls!).
For some reason the sunxi pin control driver was including the private
gpiolib header, it works just fine without it so remove that oneliner.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The generic GPIO library directly implement code for of_find_gpio()
which is only used with CONFIG_OF and causes compilation problems
on archs that do not even have stubs for OF functions, especially
on UM that does not implement any IO remap functions.
Move the function to gpiolib-of.c, implement a static inline stub
in gpiolib.h returning PTR_ERR(-ENOENT) if CONFIG_OF_GPIO is not
set and be done with it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This one is pretty obvious: on UM Linux compilation of things
like allmodconfig and allyesconfig will fail due to the
absence of IO memory. Simply make these drivers depend on
HAS_IOMEM, it has been implicitly assumed all the time, so
just make it explicit.
The generic MMIO library also assumes that IOMEM is present
so make also this depend on HAS_IOMEM.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Avoid custom (1 << bits) shifting by consequently using the
BIT() macro from <linux/bitops.h>.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Exploit the new mechanism for masking off disallowed IRQs
added by Mika Westerberg to properly manage the STMPE
"norequest mask" to disallow also mapping said lines as
IRQs.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
The HTC GPIO driver is a pure GPIO driver and I just can not
see what it is doing inside MFD. Let's just move it to GPIO
and take this opportunity to move the platform data to
<linux/platform_data/gpio-htc-egpio.h>
Cc: arm@kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch add basic structure of a virtual gpio device(gpio-mockup)
for testing gpio subsystem. The tester could manipulate such device
through userspace(sysfs or char device) and check the result from
debugfs.
Currently, it support one or more gpiochip(determined by module
parameters with base,ngpio pair). One could test the overlap of
different gpiochip and test the direction and/or output values of
these chips.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
sparse rightfully said:
drivers/gpio/gpio-pca953x.c:771:45: warning: symbol 'id' shadows an earlier one
drivers/gpio/gpio-pca953x.c:742:36: originally declared here
So, name them explicitly 'i2c_id' and 'acpi_id' to avoid any confusion.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If an I2C GPIO multiplexer is driven by a GPIO provided by an expander
when there's a second expander using the same device driver on one of
the I2C bus segments, lockdep prints a deadlock warning when trying to
set the direction or the value of the GPIOs provided by the second
expander.
The below diagram presents the setup:
- - - - -
------- --------- Bus segment 1 | |
| | | |--------------- Devices
| | SCL/SDA | | | |
| Linux |-----------| I2C MUX | - - - - -
| | | | | Bus segment 2
| | | | |-------------------
------- | --------- |
| | - - - - -
------------ | MUX GPIO | |
| | | Devices
| GPIO | | | |
| Expander 1 |---- - - - - -
| | |
------------ | SCL/SDA
|
------------
| |
| GPIO |
| Expander 2 |
| |
------------
The reason for lockdep warning is that we take the chip->i2c_lock in
pca953x_gpio_set_value() or pca953x_gpio_direction_output() and then
come right back to pca953x_gpio_set_value() when the GPIO mux kicks
in. The locks actually protect different expanders, but for lockdep
both are of the same class, so it says:
Possible unsafe locking scenario:
CPU0
----
lock(&chip->i2c_lock);
lock(&chip->i2c_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
In order to get rid of the warning, retrieve the adapter nesting depth
and use it as lockdep subclass for chip->i2c_lock.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch adds zynq specific check for bank 0 pins 7 and 8
are special and cannot be used as inputs
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Reported-by: Jonas Karlsson <Jonas.d.karlsson@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Implement the get_direction callback for the GPIOs found in the AXP209
PMIC.
Due to the way they are implemented, in the same register you have the
muxing options, GPIO directions and GPIO values. Since you have no control
over what value is there at reset, simply use output as the default.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Linux 4.8-rc6
|
|
|
|
|
