| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The MPC8xxx driver is always instantiating its generic GPIO functions
with the flag BGPIOF_BIG_ENDIAN. This means "big-endian bit order"
and means the bits representing the GPIO lines in the registers are
reversed around 31 bits so line 0 is at bit 31 and so forth down to
line 31 in bit 0.
Instead of looping into the generic MMIO gpio to do the simple
calculation of a bitmask, through a vtable call with two parameters
likely using stack frames etc (unless the compiler optimize it)
and obscuring the view for the programmer, let's just open-code
what the call does. This likely executes faster, saves space and
makes the code easier to read.
Cc: Liu Gang <Gang.Liu@nxp.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tien Hock Loh <thloh@altera.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
From the beginning of the gpio-mpc8xxx.c, the "handle_level_irq"
has being used to handle GPIO interrupts in the PowerPC/Layerscape
platforms. But actually, almost all PowerPC/Layerscape platforms
assert an interrupt request upon either a high-to-low change or
any change on the state of the signal.
So the "handle_level_irq" is not reasonable for PowerPC/Layerscape
GPIO interrupt, it should be "handle_edge_irq". Otherwise the system
may lost some interrupts from the PIN's state changes.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Setting gc->direction_output to gc->direction_output looks strange.
I think this change makes the intention more clear.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
*read_reg and *write_reg can be removed because at all the places to call
them, we can just use gc->read_reg/gc->write_reg instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For devtype with specific gpio_dir_out implementation, current code is
wrong because below code sets both gc->direction_output and
mpc8xxx_gc->direction_output to the same function.
gc->direction_output = devtype->gpio_dir_out ?: gc->direction_output;
mpc8xxx_gc->direction_output = gc->direction_output;
Set mpc8xxx_gc->direction_output = gc->direction_output first to fix it.
This way mpc8xxx_gc->direction_output actually calls the standard
bgpio_dir_out() to update register.
Fixes: commit 42178e2a1e42 ("drivers/gpio: Switch gpio-mpc8xxx to use gpio-generic")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The new Layerscape platforms has the same ip block/controller
as GPIO on PowerPC platforms(MPC8XXX), but the GPIO registers
may be big or little endian. So the code needs to get the
endian property from DTB, then make additional functions to
fit all the PowerPC/Layerscape GPIO register read/write
operations.
gpio-generic.c provides an universal infrastructure for both
big and little endian register operations. So switch the
gpio-mpc8xxx to use gpio-generic can simplify the driver and
reduce a lot of code.
The IRQ and some workaround parts in gpio-mpc8xxx.c will be
updated with the new API interfaces but following the
original functionalities.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 709d71a17c33 ("gpio: mpc8xxx: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). However, the data
pointer is not yet set by the time the save_regs function is called.
Fixes: 709d71a17c33 ("gpio: mpc8xxx: use gpiochip data pointer")
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
|
|
mpc8xxx_gpio_chip.lock needs to be a real spinlock in preempt-rt.
Especially the interrupt related functions can not be converted to a
sleeping lock.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio controller on MPC5125 is identical to the MPC5121 register
wise, the only difference is that the lines 0..3 are input only instead
of 28..31 on MPC5121.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio controllers that are handled by the mpc8xxx driver differ
slightly. Up to now some differences were handled by use of
of_device_is_compatible, others by use of struct of_device_id's data.
To make this consistent and easily extendable handle the differences at
a single place.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This variable is not modified in the driver and all functions it it
passed to don't change it either. So it can and should be marked const.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
|
|
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since commit 98686d9a52ee ("gpio: mpc8xxx: Convert to platform device
interface"), we get the following section mismatch warning. Remove the
__initdata annotation to fix it.
WARNING: vmlinux.o(.data+0xbc28): Section mismatch in reference from the variable mpc8xxx_plat_driver to the variable .init.data:mpc8xxx_gpio_ids
The variable mpc8xxx_plat_driver references
the variable __initdata mpc8xxx_gpio_ids
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since d621e8bae5ac9c67 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This way we do not need to transverse the device tree manually.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a set_multiple function to the MPC8xxx GPIO chip driver and thereby allow
for actual performance improvements when setting multiple outputs
simultaneously. In my case the time needed to configure an FPGA goes down from
48 s to 20 s.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - no change
v4: - change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
v3: - change commit message
v2: - add this patch (v1 included only changes to gpiolib)
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For MPC8572/MPC8536, the status of GPIOs defined as output
cannot be determined by reading GPDAT register, so the code
use shadow data register instead. But the code may give the
wrong status of GPIOs defined as input under some scenarios:
1. If some pins were configured as inputs and were asserted
high before booting the kernel, the shadow data has been
initialized with those pin values.
2. Some pins have been configured as output first and have
been set to the high value, then reconfigured as input.
The above cases will make the shadow data for those input
pins to be set to high. Then reading the pin status will
always return high even if the actual pin status is low.
The code should eliminate the effects of the shadow data to
the input pins, and the status of those pins should be
read directly from GPDAT.
Cc: stable@vger.kernel.org
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
|
|
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
|
|
Exporting gpios over sysfs GPIO interface throws genirq
error messages, i.e. on an mpc5121 based board exporting
GPIO 5 triggers it:
# echo 229 > /sys/class/gpio/export
genirq: Setting trigger mode 0 for irq 44 failed
(mpc512x_irq_set_type+0x0/0x18c)
Similar error messages appear in the kernel boot log since the
board specifies GPIOs for matrix keypad and also SD Card write
protect and card detect GPIOs in its device tree. For all these
GPIOs there is an error message in the log.
The issue is triggered by setting the irq type to IRQ_TYPE_NONE
in the driver's irq_domain map function mpc8xxx_gpio_irq_map().
...
mpc8xxx_gpio_irq_map
irq_set_irq_type
__irq_set_trigger
__irq_set_trigger() calls irq_set_type() callback of the mpc8xxx gpio
irq chip with the IRQ_TYPE_NONE in its 'flags' argument. This callback
is either mpc8xxx_irq_set_type() or mpc512x_irq_set_type(). Both these
functions return -EINVAL in the case if IRQ_TYPE_NONE is passed in the
flow_type argument. This return value triggers the observed error
message in __irq_set_trigger(). Modifying these callbacks to not
return an error in IRQ_TYPE_NONE case doesn't make any sense to me.
The line setting IRQ_TYPE_NONE type has been originally added by
commit 345e5c8a "powerpc: Add interrupt support to mpc8xxx_gpio".
At this time set_irq_type() checked its type argument and returned 0
if the type argument didn't specify any meaningful type in its type
sense bits (and thus was equal to IRQ_TYPE_NONE). Effectively this
line was a nop and I wonder what was the point of adding it.
Remove IRQ_TYPE_NONE setting in the irq_domain mapping function.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/gpio/gpio-mpc8xxx.c: In function 'mpc8xxx_add_controller':
drivers/gpio/gpio-mpc8xxx.c:360:30: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
commit cfadd838(powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO
driver) added an unconditional call of chip->irq_eoi() to the demux
handler.
This leads to a NULL pointer derefernce on MPC512x platforms which use
this driver as well.
Make it conditional.
Reported-by: Thomas Wucher <thwucher@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Felix Radensky <felix@embedded-sol.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch converts a number of the powerpc drivers to use the common library
of irq_domain xlate functions, dropping a bunch of lines in the process.
v5: - Remove tsi108 changes from patch
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
|
|
Each revmap type has different arguments for setting up the revmap.
This patch splits up the generator functions so that each revmap type
can do its own setup and the user doesn't need to keep track of how
each revmap type handles the arguments.
This patch also adds a host_data argument to the generators. There are
cases where the host_data pointer will be needed before the function returns.
ie. the legacy map calls the .map callback for each irq before returning.
v2: - Add void *host_data argument to irq_domain_add_*() functions
- fixed failure to compile
- Moved IRQ_DOMAIN_MAP_* defines into irqdomain.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
|
|
This patch drops the powerpc-specific irq_host structures and uses the common
irq_domain strucutres defined in linux/irqdomain.h. It also fixes all
the users to use the new structure names.
Renaming irq_host to irq_domain has been discussed for a long time, and this
patch is a step in the process of generalizing the powerpc virq code to be
usable by all architecture.
An astute reader will notice that this patch actually removes the irq_host
structure instead of renaming it. This is because the irq_domain structure
already exists in include/linux/irqdomain.h and has the needed data members.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
|
|
Add a 5121-custom reject if an input-only pin is requested to be output
(see 18.3.1.1 in the refman). Also, rewrite mach-specific quirk setup to
consume less lines which scales better.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
[grant.likely: Fixed build error]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Interrupt handler in MPC8xxx GPIO driver is missing the call to PIC EOI
(end of interrupt) handler. As a result, at least on 85XX systems, GPIO
interrupt is delivered only once. This patch adds the missing EOI call.
Tested on custom P1022 board.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Support MPC85xx platforms outside of MPC8572/MPC8536. The
MPC8572/MPC8536 have an erratum that is worked around based on having
"fsl,mpc8572-gpio" in the compatiable list. All other MPC85xx SoCs
don't require this workaround and thus utilize the 'fsl,pq3-gpio'
compatiable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
