| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This GPIO driver is for HiSilicon's ARM SoC.
HiSilicon's GPIO controller support double-edge interrupt and multi-core
concurrent access.
ACPI table example for this GPIO controller:
Device (GPO0)
{
Name (_HID, "HISI0184")
Device (PRTA)
{
Name (_ADR, Zero)
Name (_UID, Zero)
Name (_DSD, Package (0x01)
{
Package (0x02)
{
"ngpios",
0x20
}
})
}
}
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Link: https://lore.kernel.org/r/1607934255-52544-2-git-send-email-luojiaxing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a driver that supports the GPIO block found in
MStar/SigmaStar ARMv7 SoCs.
The controller seems to have enough register for 128 lines
but where they are wired up differs between chips and
no currently known chip uses anywhere near 128 lines so there
needs to be some per-chip data to collect together what lines
actually have physical pins attached and map the right names to them.
The core peripherals seem to use the same lines on the
currently known chips but the lines used for the sensor
interface, lcd controller etc pins seem to be totally
different between the infinity and mercury chips
The code tries to collect all of the re-usable names,
offsets etc together so that it's easy to build the extra
per-chip data for other chips in the future.
So far this only supports the MSC313 and MSC313E chips.
Support for the SSC8336N (mercury5) is trivial to add once
all of the lines have been mapped out.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20201129110803.2461700-4-daniel@0x0f.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for initialising shared (between children) Regmaps
- Add support for Kontron SL28CPLD
- Add support for ENE KB3930 Embedded Controller
- Add support for Intel FPGA PAC MAX 10 BMC
New Device Support:
- Add support for Power to Ricoh RN5T618
- Add support for UART to Intel Lakefield
- Add support for LP87524_Q1 to Texas Instruments LP87565
New Functionality:
- Device Tree; ene-kb3930, sl28cpld, syscon, lp87565, lp87524-q1
- Use new helper dev_err_probe(); madera-core, stmfx, wcd934x
- Use new GPIOD API; dm355evm_msp
- Add wake-up capability; sprd-sc27xx-spi
- Add ACPI support; kempld-core
Fix-ups:
- Trivial (spelling/whitespace); Kconfig, ab8500
- Fix for unused variables; khadas-mcu, kempld-core
- Remove unused header file(s); mt6360-core
- Use correct IRQ flags in docs; act8945a, gateworks-gsc, rohm,bd70528-pmic
- Add COMPILE_TEST support; asic3, tmio_core
- Add dependency on I2C; SL28CPLD
Bug Fixes:
- Fix memory leak(s); sm501
- Do not free regmap_config's 'name' until exit; syscon"
* tag 'mfd-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (34 commits)
mfd: kempld-core: Fix unused variable 'kempld_acpi_table' when !ACPI
mfd: sl28cpld: Depend on I2C
mfd: asic3: Build if COMPILE_TEST=y
dt-bindings: mfd: Correct interrupt flags in examples
mfd: Add ACPI support to Kontron PLD driver
mfd: intel-m10-bmc: Add Intel MAX 10 BMC chip support for Intel FPGA PAC
mfd: lp87565: Add LP87524-Q1 variant
dt-bindings: mfd: Add LP87524-Q1
dt-bindings: mfd: lp87565: Convert to yaml
mfd: mt6360: Remove unused include <linux/version.h>
mfd: sm501: Fix leaks in probe()
mfd: syscon: Don't free allocated name for regmap_config
dt-bindings: mfd: syscon: Document Exynos3 and Exynos5433 compatibles
dt-bindings: mfd: syscon: Merge Samsung Exynos Sysreg bindings
dt-bindings: mfd: ab8500: Remove weird Unicode characters
mfd: sprd: Add wakeup capability for PMIC IRQ
mfd: intel-lpss: Add device IDs for UART ports for Lakefield
mfd: dm355evm_msp: Convert LEDs to GPIO descriptor table
mfd: wcd934x: Simplify with dev_err_probe()
mfd: stmfx: Simplify with dev_err_probe()
...
|
|
Make the gpiolib-cdev module a build option. This allows the CDEV
interface to be removed from the kernel to reduce kernel size in
applications where is it not required, and provides the parent for
other CDEV interface specific build options to follow.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add support for the GPIO controller of the sl28 board management
controller. This driver is part of a multi-function device.
A controller has 8 lines. There are three different flavors:
full-featured GPIO with interrupt support, input-only and output-only.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Now that devprop_gpiochip_set_names() is only used in a single place
inside drivers/gpio/gpiolib.c, there's no need anymore for it to be
exported or to even live in its own source file. Pull this function into
the core source file for gpiolib.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
NXP PCA9570 is a 4-bit I2C GPO expander without interrupt functionality.
Its ports are controlled only by a data byte without register address.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Datasheet: https://www.nxp.com/docs/en/data-sheet/PCA9570.pdf
Link: https://lore.kernel.org/r/20200709134829.216393-1-mans0n@gorani.run
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Split the cdev specific functionality out of gpiolib.c and into
gpiolib-cdev.c. This improves the readability and maintainability of both
the cdev and core gpiolib code.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20200616093615.5167-1-warthog618@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There are quite a lot simple GPIO controller which are using regmap to
access the hardware. This driver tries to be a base to unify existing
code into one place. This won't cover everything but it should be a good
starting point.
It does not implement its own irq_chip because there is already a
generic one for regmap based devices. Instead, the irq_chip will be
instantiated in the parent driver and its irq domain will be associate
to this driver.
For now it consists of the usual registers, like set (and an optional
clear) data register, an input register and direction registers.
Out-of-the-box, it supports consecutive register mappings and mappings
where the registers have gaps between them with a linear mapping between
GPIO offset and bit position. For weirder mappings the user can register
its own .xlate().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200528145845.31436-3-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIO controllers are exported to userspace using /dev/gpiochip*
character devices. Access control to these devices is provided by
standard UNIX file system permissions, on an all-or-nothing basis:
either a GPIO controller is accessible for a user, or it is not.
Currently no mechanism exists to control access to individual GPIOs.
Hence add a GPIO driver to aggregate existing GPIOs, and expose them as
a new gpiochip.
This supports the following use cases:
- Aggregating GPIOs using Sysfs
This is useful for implementing access control, and assigning a set
of GPIOs to a specific user or virtual machine.
- Generic GPIO Driver
This is useful for industrial control, where it can provide
userspace access to a simple GPIO-operated device described in DT,
cfr. e.g. spidev for SPI-operated devices.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Link: https://lore.kernel.org/r/20200511145257.22970-5-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds support for the GPIO controller used by
Mellanox BlueField 2 SOCs.
Signed-off-by: Asmaa Mnebhi <Asmaa@mellanox.com>
Link: https://lore.kernel.org/r/1680de9eb6d2b8855228dde9a2dd065f0dcbe1fb.1583182325.git.Asmaa@mellanox.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.6 kernel cycle.
This is a pretty calm cycle so far, nothing special going on really.
Some more changes will come in from the irqchip and pin control trees.
I also deleted an orphan include file for FMC that was dangling since
subsystem was removed.
Core changes:
- Document the usecases for the kernelspace vs userspace handling of
GPIOs.
- Handle MSI (message signalled interrupts) properly in the core
hierarchical irqdomain code.
- Fix a rare race condition while initializing the descriptor array.
New drivers:
- Xylon LogiCVC GPIO driver.
- WDC934x GPIO controller driver.
Driver improvements:
- Implemented suspend/resume in the Tegra driver.
- MPC8xx edge detection fixup.
- Properly convert ThunderX to use hierarchical irqdomain with
GPIOLIB_IRQCHIP on top of the revert of the previous buggy
switchover. This time it works (hopefully).
Misc:
- Drop a FMC remnant file <linux/ipmi-fru.h>
- A slew of fixes"
* tag 'gpio-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (48 commits)
MAINTAINERS: Replace Tien Hock Loh as Altera PIO maintainer
gpiolib: hold gpio devices lock until ->descs array is initialised
gpio: aspeed-sgpio: fixed typos
gpio: mvebu: clear irq in edge cause register before unmask edge irq
gpiolib: Lower verbosity when allocating hierarchy irq
gpiolib: Remove duplicated function gpio_do_set_config()
gpio: Fix the no return statement warning
gpio: wcd934x: Add support to wcd934x gpio controller
gpiolib: remove set but not used variable 'config'
gpio: vx855: fixed a typo
gpio: mockup: sort headers alphabetically
gpio: mockup: update the license tag
gpio: Remove the unused flags
gpiolib: Set lockdep class for hierarchical irq domains
gpio: thunderx: Switch to GPIOLIB_IRQCHIP
gpiolib: Add the support for the msi parent domain
gpiolib: Add support for the irqdomain which doesn't use irq_fwspec as arg
gpio: Add use guidance documentation
dt-bindings: gpio: wcd934x: Add bindings for gpio
gpio: altera: change to platform_get_irq_optional to avoid false-positive error
...
|
|
ROHM BD71828 PMIC contains 4 pins which can be configured by OTP
to be used for general purposes. First 3 can be used as outputs
and 4.th pin can be used as input. Allow them to be controlled
via GPIO framework.
The driver assumes all of the pins are configured as GPIOs and
trusts that the reserved pins in other OTP configurations are
excluded from control using "gpio-reserved-ranges" device tree
property (or left untouched by GPIO users).
Typical use for 4.th pin (input) is to use it as HALL sensor
input so that this pin state is toggled when HALL sensor detects
LID position change (from close to open or open to close). PMIC
HW implements some extra logic which allows PMIC to power-up the
system when this pin is toggled. Please see the data sheet for
details of GPIO options which can be selected by OTP settings.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Adds the GPIO driver for SiFive RISC-V SoCs.
Signed-off-by: Wesley W. Terpstra <wesley@sifive.com>
[Atish: Various fixes and code cleanup]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1575976274-13487-6-git-send-email-yash.shah@sifive.com
|
|
This patch adds support to wcd934x gpio block found in
WCD9340/WC9341 Audio codecs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200107130844.20763-3-srinivas.kandagatla@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Move Lynxpoint GPIO driver under Intel pin control umbrella
for further transformation to a real pin control driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The LogiCVC display hardware block comes with GPIO capabilities
that must be exposed separately from the main driver (as GPIOs) for
use with regulators and panels. A syscon is used to share the same
regmap across the two drivers.
Add a minimalistic GPIO driver to drive these GPIOs, using a syscon
regmap when available.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://lore.kernel.org/r/20191203141243.251058-5-paul.kocialkowski@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This driver supports the Chip Common A GPIO controller present on a
number of Broadcom switch ASICs with integrated SoCs. The controller is
similar to the pinctrl-nsp-gpio and pinctrl-iproc-gpio blocks but
different enough that a separate driver is required.
This has been ported from Broadcom's XLDK 5.0.3 retaining only the CCA
support (pinctrl-iproc-gpio covers CCB).
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191024202703.8017-3-chris.packham@alliedtelesis.co.nz
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support for GPIO controller from RDA Micro. This GPIO controller
is an in house IP, developed by RDA Micro (now Unisoc) for the use in
RDA88* series of SoCs. There are multiple GPIO ports present in all SoCs,
each capable of addressing 32 GPIOs. But only first 8 pins have the
interrupt capability.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20191021064413.19840-4-manivannan.sadhasivam@linaro.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This renames the "gpio-aspeed" driver to conform with other
GPIO drivers as "gpio-aspeed-sgpio.c". All GPIO drivers
should start with the string "gpio-" no special exceptions.
Also the Kconfig and Makefile entries should normally
go with the driver but I missed this in my review, sorry
for mistake. "CONFIG_GPIO_ASPEED_SGPIO" is used to
activate this driver.
Cc: Hongwei Zhang <hongweiz@ami.com>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190927114833.12551-1-linus.walleij@linaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.4
- use a helper variable for &pdev->dev in gpio-em
- tweak the ifdefs in GPIO headers
- fix function links in HTML docs
- remove an unneeded error message from ixp4xx
- use the optional clk_get in gpio-mxc instead of checking the return value
- a couple improvements in pca953x
- allow to build gpio-lpc32xx on non-lpc32xx targets
|
|
This adds support for interpreting the input and output bits of one
device on Moxtet bus as GPIOs.
This is needed for example by the SFP cage module of Turris Mox.
Link: https://lore.kernel.org/r/20190812161118.21476-5-marek.behun@nic.cz
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The driver uses hardwire MMIO addresses instead of the data
that is passed in device tree. Change it over to only
hardcode the register offset values and allow compile-testing.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The platform is getting removed, so there are no remaining
users of this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190809202749.742267-4-arnd@arndb.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Set 'struct device' fwnode when registering a new device
New Drivers:
- Add support for ROHM BD70528 PMIC
New Device Support:
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
New Functionality:
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
Fix-ups:
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
Bug Fixes:
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera"
* tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: hi655x-pmic: Fix missing return value check for devm_regmap_init_mmio_clk
mfd: madera: Fixup SPDX headers
mfd: madera: Remove some unused registers and fix some defaults
mfd: intel-lpss: Release IDA resources
mfd: intel-lpss: Add Intel Elkhart Lake PCH PCI IDs
mfd: cs5535-mfd: Remove ifdef OLPC noise
mfd: stmfx: Fix macro definition spelling
dt-bindings: mfd: Add link to ROHM BD71847 Datasheet
MAINAINERS: Swap words in INTEL PMIC MULTIFUNCTION DEVICE DRIVERS
mfd: cros_ec_dev: Register cros_ec_accel_legacy driver as a subdevice
mfd: rk808: Prepare rk805 for poweroff
mfd: rk808: Check pm_power_off pointer
mfd: cros_ec: differentiate SCP from EC by feature bit
dt-bindings: Add binding for cros-ec-rpmsg
mfd: madera: Add Madera core support for CS47L92
mfd: madera: Add Madera core support for CS47L15
mfd: madera: Update DT bindings to add additional CODECs
mfd: madera: Add supply mapping for MICVDD
mfd: madera: Fix potential uninitialised use of variable
mfd: madera: Fix bad reference to pinctrl.txt file
...
|
|
Sort the definitions for the individual GPIO drivers
in the Makefile by object file name. Align all entries
while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
ROHM BD70528 PMIC has 4 GPIO pins. Allow them to be
controlled by GPIO framework.
IRQs are handled by regmap-irq and GPIO driver is not
aware of the irq usage.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Document (kerneldoc) core mfd_add_devices() API
New Drivers:
- Altera SOCFPGA System Manager
- Maxim MAX77650/77651 PMIC
- Maxim MAX77663 PMIC
- ST Multi-Function eXpander (STMFX)
New Device Support:
- LEDs support in Intel Cherry Trail Whiskey Cove PMIC
- RTC support in SAMSUNG Electronics S2MPA01 PMIC
- SAM9X60 support in Atmel HLCDC (High-end LCD Controller)
- USB X-Powers AXP 8xx PMICs
- Integrated Sensor Hub (ISH) in ChromeOS EC
- USB PD Logger in ChromeOS EC
- AXP223 in X-Powers AXP series PMICs
- Power Supply in X-Powers AXP 803 PMICs
- Comet Lake in Intel Low Power Subsystem
- Fingerprint MCU in ChromeOS EC
- Touchpad MCU in ChromeOS EC
- Move TI LM3532 support to LED
New Functionality:
- max77650, max77620: Add/extend DT support
- max77620 power-off
- syscon clocking
- croc_ec host sleep event
Fix-ups:
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
Bug Fixes:
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio"
* tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: Use dev_get_drvdata() directly
mfd: cros_ec: Instantiate properly CrOS Touchpad MCU device
mfd: cros_ec: Instantiate properly CrOS FP MCU device
mfd: cros_ec: Update the EC feature codes
mfd: intel-lpss: Add Intel Comet Lake PCI IDs
mfd: lochnagar: Add links to binding docs for sound and hwmon
mfd: ab8500-debugfs: Fix a typo ("deubgfs")
mfd: imx6sx: Add MQS register definition for iomuxc gpr
dt-bindings: mfd: LMU: Fix lm3632 dt binding example
mfd: intel_quark_i2c_gpio: Adjust IOT2000 matching
mfd: da9063: Fix OTP control register names to match datasheets for DA9063/63L
mfd: tps65912-spi: Add missing of table registration
mfd: axp20x: Add USB power supply mfd cell to AXP803
mfd: sun6i-prcm: Fix build warning for non-OF configurations
mfd: intel-lpss: Set the device in reset state when init
platform/chrome: Add support for v1 of host sleep event
mfd: cros_ec: Add host_sleep_event_v1 command
mfd: cros_ec: Instantiate the CrOS USB PD logger driver
mfd: cs47l90: Make DAC_AEC_CONTROL_2 readable
mfd: cs47l35: Make DAC_AEC_CONTROL_2 readable
...
|
|
Add GPIO support for max77650 mfd device. This PMIC exposes a single
GPIO line.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This adds a driver for the IXP4xx GPIO block found in
the Intel XScale IXP4xx systems.
The GPIO part of this block is pretty straight-forward and
just uses the generic MMIO GPIO library.
The irqchip side of this driver is hierarchical where
the main irqchip will receive a processed level trigger
in response to the edge detector of the GPIO block,
so for this reason the v2 version of the irqdomain API
is used (as well as in the parent IXP4xx irqchip) and
masking, unmasking and setting up the type on IRQ
happens on several levels.
Currently this GPIO controller will grab the parent
irqdomain using a special function, but as the platform
move toward device tree probing, this will not be needed:
we can just look up the parent irqdomain from the device
tree.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds support for the GPIO controller used by Mellanox
BlueField SOCs.
Reviewed-by: David Woods <dwoods@mellanox.com>
Signed-off-by: Shravan Kumar Ramani <sramani@mellanox.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
GPIO platform driver for the AMD G-series PCH (eg. on GX-412TC)
This driver doesn't registers itself automatically, as it needs to
be provided with platform specific configuration, provided by some
board driver setup code.
Didn't implement oftree probing yet, as it's rarely found on x86.
Cc: linux-gpio@vger.kernel.org
Cc: linus.walleij@linaro.org
Cc: bgolaszewski@baylibre.com
Cc: dvhart@infradead.org
Cc: platform-driver-x86@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a driver for Gateworks PLD GPIO, that exist in
two instances on the Gateworks Cambria GW2358-4 router
platform at least.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some TQ-Systems ComExpress modules contain an IO controller with 8
GPIO lines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds a driver for Cadence GPIO controller.
It can be enabled with GPIO_CADENCE Kconfig option.
It uses generic GPIO infrastructure and works
as an interrupt controller.
At the moment it only supports level sensitive irqs.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
PIOBU pins do not lose their voltage during Backup/Self-refresh.
This patch adds a simple GPIO controller for them and a
maintainer for the driver.
This driver adds support for using the pins as GPIO
offering the possibility to read/set the voltage.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add single-register MMIO GPIO driver for complex cases where
only several fields in register belong to GPIO lines and each GPIO
line owns a field with different length and on/off value.
Such CREG GPIOs are used in Synopsys AXS10x and HSDK boards.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This driver controls a SIOX device that provides 20 I/O lines. The first
twelve are fixed inputs, the remaining eight are outputs.
Acked-by: Gavin Schenk <g.schenk@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
All the other core files are named "gpiolib-<something>" so
let's rename the devres as well so we have some logical
namespacing here.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pinctrl-ingenic driver is now handling the GPIO chips directly.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
|
|
Add driver support for gpio of MT7621 SoC.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
[Switched wording WIDTH to STRIDE]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds support for the GPIOs on Cirrus Logic Madera class codecs.
Any pins not used for special functions (see the pinctrl driver) can be
used as general single-bit input or output lines. The number of available
GPIOs varies between codecs.
Note that this is part of a composite MFD for these codecs and can only
be used with the corresponding MFD and other child drivers on those
silicon. The GPIO block on these codecs does not exist indepedently of
the rest of the MFD.
Signed-off-by: Nariman Poushin <nariman@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
|
|
The Spreadtrum PMIC EIC controller contains only one bank of debounce EIC,
and this bank contains 16 EICs. Each EIC can only be used as input mode,
as well as supporting the debounce and the capability to trigger interrupts
when detecting input signals.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Spreadtrum digital-chip EIC controller has 4 sub-modules: debounce EIC,
latch EIC, async EIC and sync EIC, and each sub-module can has multiple
banks and each bank contains 8 EICs.
Each EIC can only be used as input mode, and has the capability to trigger
interrupts when detecting input signals.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
