summaryrefslogtreecommitdiffstats
path: root/drivers/gnss/sirf.c
AgeCommit message (Collapse)AuthorFilesLines
2019-01-25gnss: sirf: add a separate supply for a lnaAndreas Kemnade1-6/+52
Devices might have a separate lna between antenna input of the gps chip and the antenna which might have a separate supply. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-01-25gnss: sirf: add support for configurations without wakeup signalAndreas Kemnade1-27/+102
Some Wi2Wi devices do not have a wakeup output, so device state can only be indirectly detected by looking whether there is communication over the serial lines. This approach requires a report cycle set to a value less than 2 seconds to be reliable. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> [ johan: simplify sirf_set_active(), style changes ] Signed-off-by: Johan Hovold <johan@kernel.org>
2019-01-25gnss: sirf: write data to gnss only when the gnss device is openAndreas Kemnade1-2/+30
The api forbids writing data there otherwise. Prepare for the serdev_open()/close() being a part of sirf_set_active. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-01-25gnss: sirf: drop redundant double negationJohan Hovold1-1/+1
The active flag is of type bool so drop the redundant double negation when storing the gpio state. Signed-off-by: Johan Hovold <johan@kernel.org>
2019-01-25gnss: sirf: force hibernate mode on probeJohan Hovold1-0/+17
Make sure to put the receiver in hibernate mode in case it is already active during probe in order to avoid wasting power until first open or suspend. This can happen, for example, after a reset or non-clean shutdown, and possibly also due to glitches during power-on. Reported-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-01-25gnss: sirf: fix premature wakeup interrupt enableJohan Hovold1-15/+17
Make sure the receiver is powered (and booted) before enabling the wakeup interrupt to avoid spurious interrupts due to a floating input. Similarly, disable the interrupt before powering off on probe errors and on unbind. Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers") Cc: stable <stable@vger.kernel.org> # 4.19 Signed-off-by: Johan Hovold <johan@kernel.org>
2018-12-10Merge 4.20-rc6 into tty-nextGreg Kroah-Hartman1-3/+3
We want the TTY changes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-06gnss: sirf: fix activation retry handlingJohan Hovold1-3/+3
Fix activation helper which would return -ETIMEDOUT even if the last retry attempt was successful. Also change the semantics of the retries variable so that it actually holds the number of retries (rather than tries). Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers") Cc: stable <stable@vger.kernel.org> # 4.19 Signed-off-by: Johan Hovold <johan@kernel.org>
2018-11-27serdev: make synchronous write return bytes writtenJohan Hovold1-1/+1
Make the synchronous serdev_device_write() helper behave analogous to the asynchronous serdev_device_write_buf() by returning the number of bytes written (or rather buffered) also on timeout. This will allow drivers to distinguish the case where data was partially written from the case where no data was written. Also update the only two users that checked the return value. Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-14gnss: sirf: fix synchronous write timeoutJohan Hovold1-1/+2
Passing a timeout of zero to the synchronous serdev_device_write() helper does currently not imply to wait forever (unlike passing zero to serdev_device_wait_until_sent()). Instead, if there's insufficient room in the write buffer, we'd end up with an incomplete write. Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers") Cc: stable <stable@vger.kernel.org> # 4.19 Signed-off-by: Johan Hovold <johan@kernel.org>
2018-06-28gnss: add receiver type supportJohan Hovold1-0/+1
Add a "type" device attribute and a "GNSS_TYPE" uevent variable which can be used to determine the type of a GNSS receiver. The currently identified types reflect the protocol(s) supported by a receiver: "NMEA" NMEA 0183 "SiRF" SiRF Binary "UBX" UBX Note that both SiRF and UBX type receivers typically support a subset of NMEA 0183 with vendor extensions (e.g. to allow switching to the vendor protocol). Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-28gnss: add driver for sirfstar-based receiversJohan Hovold1-0/+407
Add driver for serial-connected SiRFstar-based GNSS receivers. These devices typically boot into hibernate mode from which they can be woken using a pulse on the ON_OFF input pin. Once active, a pulse on the same ON_OFF pin is used to put the device back into hibernate mode. The current state can be determined by sampling the WAKEUP output. Hardware configurations where WAKEUP has been connected to ON_OFF (and where an initial WAKEUP pulse during boot is sufficient to have the device boot into active mode) are also supported. In this case, device power is managed using the main-supply regulator only. Note that configurations where WAKEUP is left not connected, so that the device power state can only indirectly be determined using the I/O interface, is currently not supported. It should be fairly straight-forward to extend the current implementation with such support however (and this this is the main reason for not using the generic serial implementation for this driver). Note that timepulse-support is left unimplemented. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>