summaryrefslogtreecommitdiffstats
path: root/drivers/dma
AgeCommit message (Collapse)AuthorFilesLines
2011-03-07drivers, pch_dma: Fix warning when CONFIG_PM=n.Rakib Mullick1-0/+2
When CONFIG_PM=n, we get the following warning: drivers/dma/pch_dma.c:741: warning: ‘pch_dma_suspend’ defined but not used drivers/dma/pch_dma.c:755: warning: ‘pch_dma_resume’ defined but not used To fix it, wrap pch_dma_{suspend,resume} and pch_dma_{save,restore}_regs functions with CONFIG_PM. Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dmaengine/dw_dmac fix: use readl & writel instead of __raw_readl & __raw_writelViresh Kumar1-4/+4
On ARMv7 cores, device memory mapped as Normal Non-cacheable, may not guarantee ordered access causing failures in device drivers that do not use the mandatory memory barriers. readl & writel versions contain necessary memory barriers for this. commit 79f64dbf68c8a9779a7e9a25e0a9f0217a25b57a: "ARM: 6273/1: Add barriers to the I/O accessors if ARM_DMA_MEM_BUFFERABLE" can be referred for more information on this. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Setting Default Burst length for transfers as 16.Viresh Kumar1-2/+2
This patch sets default Burst length for all transfer to 16. This will enhance performance when user doesn't have any chan->private data. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Allow src/dst msize & flow controller to be configured at runtimeViresh KUMAR2-6/+9
Msize or Burst Size is peripheral dependent in case of prep_slave_sg and cyclic_prep transfers, and in case of memcpy transfers it is platform dependent. So msize configuration must come from platform data. Also some peripherals (ex: JPEG), need to be flow controller for dma transfers, so this information in case of slave_sg & cyclic_prep transfers must come from platform data. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Pass Channel Priority from platform_dataViresh Kumar2-1/+13
In Synopsys designware, channel priority is programmable. This patch adds support for passing channel priority through platform data. By default Ascending channel priority will be followed, i.e. channel 0 will get highest priority and channel 7 will get lowest. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Pass Channel Allocation Order from platform_dataViresh Kumar1-1/+5
In SPEAr Platform channels 4-7 have more Fifo depth. So we must get better channel first. This patch introduces concept of channel allocation order in dw_dmac. If user doesn't pass anything or 0, than normal (ascending) channel allocation will follow, else channels will be allocated in descending order. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Mark all tx_descriptors with DMA_CRTL_ACK after xfer finishViresh Kumar1-0/+7
dwc_desc_get checks all descriptors for DMA_CTRL_ACK before allocating them for transfers. And descriptors are not marked with DMA_CRTL_ACK after transfer finishes. Thus descriptor once used is not usable again. This patch marks descriptors with DMA_CRTL_ACK after dma xfer finishes Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Change value of DWC_MAX_COUNT to 4095.Viresh Kumar1-3/+2
Every descriptor can transfer a maximum count of 4095 (12 bits, in control reg), So we must have DWC_MAX_COUNT as 4095 instead of 2048. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Adding support for 64 bit access width for memcpy xfersViresh Kumar1-1/+3
Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Calling dwc_scan_descriptors from dwc_tx_status() after taking lockViresh Kumar1-0/+2
Lock must be taken before calling dwc_scan_descriptors, as this may access/modify shared data and queues. dwc_tx_status wasn't taking lock before calling this routine. This patch add code that takes lock before calling dwc_scan_descriptors. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Move single descriptor from dwc->queue to dwc->active_list in ↵Viresh Kumar1-12/+8
dwc_complete_all dwc_complete_all and other routines was removing all descriptors from dwc->queue and pushing them to dwc->active_list. Only one was required to be removed. Also we are calling dwc_dostart, once list is fixed. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Replace module_init() with subsys_initcall()Viresh Kumar1-1/+1
In some cases users of dw_dmac are initialized before dw_dmac, and if they try to use dw_dmac, they simply fail. So its better we register init() routine of driver using subsys_initcall() instead of module_init(), so that dma driver is available at the earliest possible. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-07dw_dmac: Remove compilation dependency from AVR32 and put on HAVE_CLKViresh Kumar1-1/+1
This driver will now be used in atleast two platforms AVR32 & ARM. And there is no actual hardware dependency of this driver over AVR32 or ARM. So this dependency can be removed altogether. Also dw_dmac driver uses clk framework and must have compilation dependency on HAVE_CLK Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-03-02dmaengine: mxs-dma: add dma support for i.MX23/28Shawn Guo3-0/+733
This patch adds dma support for Freescale MXS-based SoC i.MX23/28, including apbh-dma and apbx-dma. * apbh-dma and apbx-dma are supported in the driver as two mxs-dma instances. * apbh-dma is different between mx23 and mx28, hardware version register is used to differentiate. * mxs-dma supports pio function besides data transfer. The driver uses dma_data_direction DMA_NONE to identify the pio mode, and steals sgl and sg_len to get pio words and numbers from clients. * mxs dmaengine has some very specific features, like sense function and the special NAND support (nand_lock, nand_wait4ready). These are too specific to implemented in generic dmaengine driver. * The driver refers to imx-sdma and only a single descriptor is statically assigned to each channel. Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-02-26pch_dma: set the number of array correctlyTomoya MORINAGA1-2/+2
set the number of array correctly. Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-02-26pch_dma: fix kernel error issueTomoya MORINAGA1-15/+14
fix the following kernel error ------------[ cut here ]------------ WARNING: at kernel/softirq.c:159 _local_bh_enable_ip.clone.5+0x35/0x71() Hardware name: To be filled by O.E.M. Modules linked in: pch_uart pch_dma fuse mga drm cpufreq_ondemand acpi_cpufreq mperf ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables ipv6 uinput snd_hda_codec_realtek snd_hda_intel snd_hda_codec matroxfb_base snd_hwdep 8250_pnp snd_seq snd_seq_device matroxfb_DAC1064 snd_pcm joydev 8250 matroxfb_accel snd_timer matroxfb_Ti3026 ppdev pegasus parport_pc snd parport matroxfb_g450 g450_pll serial_core video output matroxfb_misc soundcore snd_page_alloc serio_raw pcspkr ext4 jbd2 crc16 sdhci_pci sdhci mmc_core floppy [last unloaded: scsi_wait_scan] Pid: 0, comm: swapper Not tainted 2.6.37.upstream_check+ #8 Call Trace: [<c0433add>] warn_slowpath_common+0x65/0x7a [<c043825b>] ? _local_bh_enable_ip.clone.5+0x35/0x71 [<c0433b01>] warn_slowpath_null+0xf/0x13 [<c043825b>] _local_bh_enable_ip.clone.5+0x35/0x71 [<c043829f>] local_bh_enable_ip+0x8/0xa [<c06ec471>] _raw_spin_unlock_bh+0x10/0x12 [<f82b57dd>] pd_prep_slave_sg+0xba/0x200 [pch_dma] [<f82f7b7a>] pch_uart_interrupt+0x44d/0x6aa [pch_uart] [<c046fa97>] handle_IRQ_event+0x1d/0x9e [<c047146f>] handle_fasteoi_irq+0x90/0xc7 [<c04713df>] ? handle_fasteoi_irq+0x0/0xc7 <IRQ> [<c04045af>] ? do_IRQ+0x3e/0x89 [<c04035a9>] ? common_interrupt+0x29/0x30 [<c04400d8>] ? sys_getpriority+0x12d/0x1a2 [<c058bb2b>] ? arch_local_irq_enable+0x5/0xb [<c058c740>] ? acpi_idle_enter_bm+0x22a/0x261 [<c0648b11>] ? cpuidle_idle_call+0x70/0xa1 [<c0401f44>] ? cpu_idle+0x49/0x6a [<c06d9fc4>] ? rest_init+0x58/0x5a [<c089e762>] ? start_kernel+0x2d0/0x2d5 [<c089e0ce>] ? i386_start_kernel+0xce/0xd5 Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-02-14Merge branch 'dw_dmac' into dmaengineDan Williams1-14/+22
2011-02-14Merge branch 'dma40' into dmaengineDan Williams3-928/+758
2011-02-14Merge branch 'imx' into dmaengine-fixesDan Williams2-39/+63
2011-02-14dma: ipu_idmac: do not lose valid received data in the irq handlerAnatolij Gustschin1-50/+0
Currently when two or more buffers are queued by the camera driver and so the double buffering is enabled in the idmac, we lose one frame comming from CSI since the reporting of arrival of the first frame is deferred by the DMAIC_7_EOF interrupt handler and reporting of the arrival of the last frame is not done at all. So when requesting N frames from the image sensor we actually receive N - 1 frames in user space. The reason for this behaviour is that the DMAIC_7_EOF interrupt handler misleadingly assumes that the CUR_BUF flag is pointing to the buffer used by the IDMAC. Actually it is not the case since the CUR_BUF flag will be flipped by the FSU when the FSU is sending the <TASK>_NEW_FRM_RDY signal when new frame data is delivered by the CSI. When sending this singal, FSU updates the DMA_CUR_BUF and the DMA_BUFx_RDY flags: the DMA_CUR_BUF is flipped, the DMA_BUFx_RDY is cleared, indicating that the frame data is beeing written by the IDMAC to the pointed buffer. DMA_BUFx_RDY is supposed to be set to the ready state again by the MCU, when it has handled the received data. DMAIC_7_CUR_BUF flag won't be flipped here by the IPU, so waiting for this event in the EOF interrupt handler is wrong. Actually there is no spurious interrupt as described in the comments, this is the valid DMAIC_7_EOF interrupt indicating reception of the frame from CSI. The patch removes code that waits for flipping of the DMAIC_7_CUR_BUF flag in the DMAIC_7_EOF interrupt handler. As the comment in the current code denotes, this waiting doesn't help anyway. As a result of this removal the reporting of the first arrived frame is not deferred to the time of arrival of the next frame and the drivers software flag 'ichan->active_buffer' is in sync with DMAIC_7_CUR_BUF flag, so the reception of all requested frames works. This has been verified on the hardware which is triggering the image sensor by the programmable state machine, allowing to obtain exact number of frames. On this hardware we do not tolerate losing frames. This patch also removes resetting the DMA_BUFx_RDY flags of all channels in ipu_disable_channel() since transfers on other DMA channels might be triggered by other running tasks and the buffers should always be ready for data sending or reception. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-31Merge branch 'dmaengine-shawn' into dmaengineSascha Hauer1-10/+6
2011-01-31Merge branch 'dmaengine-sdma' into dmaengineSascha Hauer1-25/+35
2011-01-31dmaengine: imx-sdma: fix up param for the last BD in sdma_prep_slave_sg()Shawn Guo1-1/+4
As per the reference manual, bit "L" should be set while bit "C" should be cleared for the last buffer descriptor in the non-cyclic chain, so that sdma can stop trying to find the next BD and end the transfer. In case of sdma_prep_slave_sg(), BD_LAST needs to be set and BD_CONT be cleared for the last BD. Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine: imx-sdma: correct sdmac->status in sdma_handle_channel_loop()Shawn Guo1-1/+1
sdma_handle_channel_loop() is the handler of cyclic tx. One period success does not really mean the success of the tx. Instead of DMA_SUCCESS, DMA_IN_PROGRESS should be the one to tell. Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine: imx-sdma: return sdmac->status in sdma_tx_status()Shawn Guo1-3/+1
The sdmac->status was designed to reflect the status of the tx, so simply return it in sdma_tx_status(). Then dma client can call dma_async_is_tx_complete() to know the status of the tx. Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine: imx-sdma: set sdmac->status to DMA_ERROR in err_out of ↵Shawn Guo1-0/+1
sdma_prep_slave_sg() sdma_prep_dma_cyclic() sets sdmac->status to DMA_ERROR in err_out, and sdma_prep_slave_sg() needs to do the same. Otherwise, sdmac->status stays at DMA_IN_PROGRESS, which will make the function return immediately next time it gets called. Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine: imx-sdma: remove IMX_DMA_SG_LOOP handling in sdma_prep_slave_sg()Shawn Guo1-6/+0
This is a leftover from the time that the driver did not have sdma_prep_dma_cyclic callback and implemented sound dma as a looped sg chain. And it can be removed now. Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine i.MX dma: initialize dma capabilities outside channel loopSascha Hauer1-3/+3
The capabilities are device specific fields, not channel specific fields. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine i.MX DMA: do not initialize chan_id fieldSascha Hauer1-1/+0
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine i.MX dma: check sg entries for valid addresses and lengthsSascha Hauer1-0/+15
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine i.MX dma: set maximum segment size for our deviceSascha Hauer1-0/+4
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine i.MX SDMA: reserve channel 0 by not registering itSascha Hauer1-18/+12
We need channel 0 of the sdma engine for internal purposes. We accomplished this by calling dma_request_channel() in the probe function. This does not work when multiple dma engines are present which is the case when IPU support for i.MX31/35 is compiled in. So instead of registering channel 0 and reserving it afterwards simply do not register it in the first place. With this the dmaengine channel counting does not match sdma channel counting anymore, so we have to use sdma channel counting in the driver. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine i.MX SDMA: initialize dma capabilities outside channel loopSascha Hauer1-3/+3
The capabilities are device specific fields, not channel specific fields. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine i.MX SDMA: do not initialize chan_id fieldSascha Hauer1-1/+0
This is bogus as the dmaengine core will overwrite this field. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine i.MX sdma: check sg entries for valid addresses and lengthsSascha Hauer1-3/+17
This patch lets sdma_prep_slave_sg fail if the entries of an sg list do not start on multiples of the word size or if the lengths are not multiple of the word size. Also, catch the previously unhandled DMA_SLAVE_BUSWIDTH_8_BYTES and DMA_SLAVE_BUSWIDTH_UNDEFINED cases. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-31dmaengine i.MX sdma: set maximum segment size for our deviceSascha Hauer1-0/+3
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-01-30dma40: cyclic xfer supportRabin Vincent3-49/+167
Support cyclic transfers, which are useful for ALSA drivers. Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: stop ongoing transfers in DMA_TERMINATE_ALLRabin Vincent1-13/+21
The current implementation of DMA_TERMINATE_ALL leaves ongoing transfers running. Fix it. Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: fix DMA_SG capability and channelsRabin Vincent1-37/+34
The DMA_SG cap is enabled on the wrong channel, and the pointers are repeatedly set incorrectly. Fix it and combine the ops settings to a common function. Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: handle failure to allocate first LCLARabin Vincent1-0/+5
Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: extract lcla code into separate functionRabin Vincent1-42/+50
Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: use flags to reduce parameter countRabin Vincent2-37/+52
Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: make d40_log_buf_to_lli staticRabin Vincent2-8/+1
Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: unify src/dst addr checkRabin Vincent1-13/+16
Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: pass the info pointer all the way to reduce argument countRabin Vincent3-33/+22
Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: unify d40_log_sg_to_lli funcs for mem and slaveRabin Vincent3-85/+29
Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: combine duplicated code in log_sg_to_devRabin Vincent1-29/+23
Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: move lli_load to main source fileRabin Vincent3-35/+18
These register writes are better placed in the main source file rather than ll.c. Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: combine mem and slave prep_sg functionsRabin Vincent1-94/+62
Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-01-30dma40: remove export of stedma40_memcpy_sgRabin Vincent1-1/+1
The dmaengine framework has the API for this now. Acked-by: Per Forlin <per.forlin@stericsson.com> Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-18 17:23:01 +0000