| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Remove unnecessary static on local variable hostbridge.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
5084 3392 256 8732 221c drivers/cpufreq/speedstep-ich.o
after:
text data bss dec hex filename
5062 3304 192 8558 216e drivers/cpufreq/speedstep-ich.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a recently exposed issue in the PCI device wakeup code and
one older problem related to PCI device wakeup that has been reported
recently, modify one more piece of computations in intel_pstate to get
rid of a rounding error, fix a possible race in the schedutil cpufreq
governor, fix the device PM QoS sysfs interface to correctly handle
invalid user input, fix return values of two probe routines in devfreq
drivers and constify an attribute_group structure in devfreq.
Specifics:
- Avoid clearing the PCI PME Enable bit for devices as a result of
config space restoration which confuses AML executed afterward and
causes wakeup events to be lost on some systems (Rafael Wysocki).
- Fix the native PCIe PME interrupts handling in the cases when the
PME IRQ is set up as a system wakeup one so that runtime PM remote
wakeup works as expected after system resume on systems where that
happens (Rafael Wysocki).
- Fix the device PM QoS sysfs interface to handle invalid user input
correctly instead of using an unititialized variable value as the
latency tolerance for the device at hand (Dan Carpenter).
- Get rid of one more rounding error from intel_pstate computations
(Srinivas Pandruvada).
- Fix the schedutil cpufreq governor to prevent it from possibly
accessing unititialized data structures from governor callbacks in
some cases on systems when multiple CPUs share a single cpufreq
policy object (Vikram Mulukutla).
- Fix the return values of probe routines in two devfreq drivers
(Gustavo Silva).
- Constify an attribute_group structure in devfreq (Arvind Yadav)"
* tag 'pm-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI / PM: Fix native PME handling during system suspend/resume
PCI / PM: Restore PME Enable after config space restoration
cpufreq: schedutil: Fix sugov_start() versus sugov_update_shared() race
PM / QoS: return -EINVAL for bogus strings
cpufreq: intel_pstate: Fix ratio setting for min_perf_pct
PM / devfreq: constify attribute_group structures.
PM / devfreq: tegra: fix error return code in tegra_devfreq_probe()
PM / devfreq: rk3399_dmc: fix error return code in rk3399_dmcfreq_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Improve thermal cpu_cooling interaction with cpufreq core.
The cpu_cooling driver is designed to use CPU frequency scaling to
avoid high thermal states for a platform. But it wasn't glued really
well with cpufreq core.
For example clipped-cpus is copied from the policy structure and its
much better to use the policy->cpus (or related_cpus) fields directly
as they may have got updated. Not that things were broken before this
series, but they can be optimized a bit more.
This series tries to improve interactions between cpufreq core and
cpu_cooling driver and does some fixes/cleanups to the cpu_cooling
driver. (Viresh Kumar)
- A couple of fixes and cleanups in thermal core and imx, hisilicon,
bcm_2835, int340x thermal drivers. (Arvind Yadav, Dan Carpenter,
Sumeet Pawnikar, Srinivas Pandruvada, Willy WOLFF)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (24 commits)
thermal: bcm2835: fix an error code in probe()
thermal: hisilicon: Handle return value of clk_prepare_enable
thermal: imx: Handle return value of clk_prepare_enable
thermal: int340x: check for sensor when PTYP is missing
Thermal/int340x: Fix few typos and kernel-doc style
thermal: fix source code documentation for parameters
thermal: cpu_cooling: Replace kmalloc with kmalloc_array
thermal: cpu_cooling: Rearrange struct cpufreq_cooling_device
thermal: cpu_cooling: 'freq' can't be zero in cpufreq_state2power()
thermal: cpu_cooling: don't store cpu_dev in cpufreq_cdev
thermal: cpu_cooling: get_level() can't fail
thermal: cpu_cooling: create structure for idle time stats
thermal: cpu_cooling: merge frequency and power tables
thermal: cpu_cooling: get rid of 'allowed_cpus'
thermal: cpu_cooling: OPPs are registered for all CPUs
thermal: cpu_cooling: store cpufreq policy
cpufreq: create cpufreq_table_count_valid_entries()
thermal: cpu_cooling: use cpufreq_policy to register cooling device
thermal: cpu_cooling: get rid of a variable in cpufreq_set_cur_state()
thermal: cpu_cooling: remove cpufreq_cooling_get_level()
...
|
|
* pm-cpufreq-sched:
cpufreq: schedutil: Fix sugov_start() versus sugov_update_shared() race
* intel_pstate:
cpufreq: intel_pstate: Fix ratio setting for min_perf_pct
|
|
The busy percent calculated for the Knights Landing (KNL) platform
is 1024 times smaller than the correct busy value. This causes
performance to get stuck at the lowest ratio.
The scaling algorithm used for KNL is performance-based, but it still
looks at the CPU load to set the scaled busy factor to 0 when the
load is less than 1 percent. In this case, since the computed load
is 1024x smaller than it should be, the scaled busy factor will
always be 0, irrespective of CPU business.
This needs a fix similar to the turbostat one in commit b2b34dfe4d9a
(tools/power turbostat: KNL workaround for %Busy and Avg_MHz).
For this reason, add one more callback to processor-specific
callbacks to specify an MPERF multiplier represented by a number of
bit positions to shift the value of that register to the left to
copmensate for its rate difference with respect to the TSC. This
shift value is used during CPU busy calculations.
Fixes: ffb810563c (intel_pstate: Avoid getting stuck in high P-states when idle)
Reported-and-tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When the minimum performance limit percentage is set to the power-up
default, it is possible that minimum performance ratio is off by one.
In the set_policy() callback the minimum ratio is calculated by
applying global.min_perf_pct to turbo_ratio and rounding up, but the
power-up default global.min_perf_pct is already rounded up to the
next percent in min_perf_pct_min(). That results in two round up
operations, so for the default min_perf_pct one of them is not
required.
It is better to remove rounding up in min_perf_pct_min() as this
matches the displayed min_perf_pct prior to commit c5a2ee7dde89
(cpufreq: intel_pstate: Active mode P-state limits rework) in 4.12.
For example on a platform with max turbo ratio of 37 and minimum
ratio of 10, the min_perf_pct resulted in 28 with the above commit.
Before this commit it was 27 and it will be the same after this
change.
Fixes: 1a4fe38add8b (cpufreq: intel_pstate: Remove max/min fractions to limit performance)
Reported-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These revert one recent change in the generic power domains
framework, fix a recently introduced build issue in there and
constify attribute_group structures in some places.
Specifics:
- Revert a recent change in the generic power domains (genpd)
framework that led to regressions and turned out the be misguided
(Rafael Wysocki).
- Fix a recently introduced build issue in the generic power domains
(genpd) framework (Arnd Bergmann).
- Constify attribute_group structures in the PM core, the cpufreq
stats code and in intel_pstate (Arvind Yadav)"
* tag 'pm-extra-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: constify attribute_group structures
cpufreq: cpufreq_stats: constify attribute_group structures
PM / sleep: constify attribute_group structures
PM / Domains: provide pm_genpd_poweroff_noirq() stub
Revert "PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device"
|
|
* pm-domains:
PM / Domains: provide pm_genpd_poweroff_noirq() stub
Revert "PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device"
* pm-sleep:
PM / sleep: constify attribute_group structures
* pm-cpufreq:
cpufreq: intel_pstate: constify attribute_group structures
cpufreq: cpufreq_stats: constify attribute_group structures
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal into thermal-soc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"New SoC specific drivers:
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini
SoCs
- Various subsystem-wide cleanups
Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA data
path acceleration that has previously been used on PowerPC chips. I
ended up postponing the merge until some API questions for its unusual
MMIO access are resolved"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
clocksource: owl: Add S900 support
clocksource: Add Owl timer
soc: renesas: rcar-sysc: Use GENPD_FLAG_ALWAYS_ON
firmware: tegra: Fix locking bugs in BPMP
soc/tegra: flowctrl: Fix error handling
soc/tegra: bpmp: Implement generic PM domains
soc/tegra: bpmp: Update ABI header
PM / Domains: Allow overriding the ->xlate() callback
soc: brcmstb: enable drivers for ARM64 and BMIPS
soc: renesas: Rework Kconfig and Makefile logic
reset: Add the TI SCI reset driver
dt-bindings: reset: Add TI SCI reset binding
reset: use kref for reference counting
soc: qcom: smsm: Improve error handling, quiesce probe deferral
cpufreq: scpi: use new scpi_ops functions to remove duplicate code
firmware: arm_scpi: add support to populate OPPs and get transition latency
dt-bindings: reset: Add reset manager offsets for Stratix10
memory: omap-gpmc: add error message if bank-width property is absent
memory: omap-gpmc: make dts snippet include semicolon
reset: Add a Gemini reset controller
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
15197 2552 40 17789 457d drivers/cpufreq/intel_pstate.o
File size After adding 'const':
text data bss dec hex filename
15261 2488 40 17789 457d drivers/cpufreq/intel_pstate.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1655 256 4 1915 77b drivers/cpufreq/cpufreq_stats.o
File size After adding 'const':
text data bss dec hex filename
1695 192 4 1891 763 drivers/cpufreq/cpufreq_stats.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP hotplug updates from Thomas Gleixner:
"This update is primarily a cleanup of the CPU hotplug locking code.
The hotplug locking mechanism is an open coded RWSEM, which allows
recursive locking. The main problem with that is the recursive nature
as it evades the full lockdep coverage and hides potential deadlocks.
The rework replaces the open coded RWSEM with a percpu RWSEM and
establishes full lockdep coverage that way.
The bulk of the changes fix up recursive locking issues and address
the now fully reported potential deadlocks all over the place. Some of
these deadlocks have been observed in the RT tree, but on mainline the
probability was low enough to hide them away."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
cpu/hotplug: Constify attribute_group structures
powerpc: Only obtain cpu_hotplug_lock if called by rtasd
ARM/hw_breakpoint: Fix possible recursive locking for arch_hw_breakpoint_init
cpu/hotplug: Remove unused check_for_tasks() function
perf/core: Don't release cred_guard_mutex if not taken
cpuhotplug: Link lock stacks for hotplug callbacks
acpi/processor: Prevent cpu hotplug deadlock
sched: Provide is_percpu_thread() helper
cpu/hotplug: Convert hotplug locking to percpu rwsem
s390: Prevent hotplug rwsem recursion
arm: Prevent hotplug rwsem recursion
arm64: Prevent cpu hotplug rwsem recursion
kprobes: Cure hotplug lock ordering issues
jump_label: Reorder hotplug lock and jump_label_lock
perf/tracing/cpuhotplug: Fix locking order
ACPI/processor: Use cpu_hotplug_disable() instead of get_online_cpus()
PCI: Replace the racy recursion prevention
PCI: Use cpu_hotplug_disable() instead of get_online_cpus()
perf/x86/intel: Drop get_online_cpus() in intel_snb_check_microcode()
x86/perf: Drop EXPORT of perf_check_microcode
...
|
|
* pm-cpufreq:
cpufreq / CPPC: Initialize policy->min to lowest nonlinear performance
cpufreq: sfi: make freq_table static
cpufreq: exynos5440: Fix inconsistent indenting
cpufreq: imx6q: imx6ull should use the same flow as imx6ul
cpufreq: dt: Add support for hi3660
* intel_pstate:
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
intel_pstate: skip scheduler hook when in "performance" mode
intel_pstate: delete scheduler hook in HWP mode
x86: use common aperfmperf_khz_on_cpu() to calculate KHz using APERF/MPERF
cpufreq: intel_pstate: Remove max/min fractions to limit performance
x86: do not use cpufreq_quick_get() for /proc/cpuinfo "cpu MHz"
* pm-cpuidle:
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
x86/ACPI/cstate: Allow ACPI C1 FFH MWAIT use on AMD systems
ARM: cpuidle: Support asymmetric idle definition
|
|
* pm-tools:
cpupower: Add support for new AMD family 0x17
cpupower: Fix bug where return value was not used
tools/power turbostat: update version number
tools/power turbostat: decode MSR_IA32_MISC_ENABLE only on Intel
tools/power turbostat: stop migrating, unless '-m'
tools/power turbostat: if --debug, print sampling overhead
tools/power turbostat: hide SKL counters, when not requested
intel_pstate: use updated msr-index.h HWP.EPP values
tools/power x86_energy_perf_policy: support HWP.EPP
x86: msr-index.h: fix shifts to ULL results in HWP macros.
x86: msr-index.h: define HWP.EPP values
x86: msr-index.h: define EPB mid-points
|
|
After commit 82b4e03e01bc (intel_pstate: skip scheduler hook when in
"performance" mode) get_target_pstate_use_performance() and
get_target_pstate_use_cpu_load() are never called if scaling_governor
is "performance", so drop the CPUFREQ_POLICY_PERFORMANCE checks from
them as they will never trigger anyway.
Moreover, the documentation needs to be updated to reflect the change
made by the above commit, so do that too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Description of Lowest Perfomance in ACPI 6.1 specification states:
"Lowest Performance is the absolute lowest performance level of
the platform. Selecting a performance level lower than the lowest
nonlinear performance level may actually cause an efficiency penalty,
but should reduce the instantaneous power consumption of the processor.
In traditional terms, this represents the T-state range of performance
levels."
Set the default value of policy->min to Lowest Nonlinear Performance
to avoid any potential efficiency penalty.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexey Klimov <alexey.klimov@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When the governor is set to "performance", intel_pstate does not
need the scheduler hook for doing any calculations. Under these
conditions, its only purpose is to continue to maintain
cpufreq/scaling_cur_freq.
The cpufreq/scaling_cur_freq sysfs attribute is now provided by
shared x86 cpufreq code on modern x86 systems, including
all systems supported by the intel_pstate driver.
So in "performance" governor mode, the scheduler hook can be skipped.
This applies to both in Software and Hardware P-state control modes.
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpufreq/scaling_cur_freq sysfs attribute is now provided by
shared x86 cpufreq code on modern x86 systems, including
all systems supported by the intel_pstate driver.
In HWP mode, maintaining that value was the sole purpose of
the scheduler hook, intel_pstate_update_util_hwp(),
so it can now be removed.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The goal of this change is to give users a uniform and meaningful
result when they read /sys/...cpufreq/scaling_cur_freq
on modern x86 hardware, as compared to what they get today.
Modern x86 processors include the hardware needed
to accurately calculate frequency over an interval --
APERF, MPERF, and the TSC.
Here we provide an x86 routine to make this calculation
on supported hardware, and use it in preference to any
driver driver-specific cpufreq_driver.get() routine.
MHz is computed like so:
MHz = base_MHz * delta_APERF / delta_MPERF
MHz is the average frequency of the busy processor
over a measurement interval. The interval is
defined to be the time between successive invocations
of aperfmperf_khz_on_cpu(), which are expected to to
happen on-demand when users read sysfs attribute
cpufreq/scaling_cur_freq.
As with previous methods of calculating MHz,
idle time is excluded.
base_MHz above is from TSC calibration global "cpu_khz".
This x86 native method to calculate MHz returns a meaningful result
no matter if P-states are controlled by hardware or firmware
and/or if the Linux cpufreq sub-system is or is-not installed.
When this routine is invoked more frequently, the measurement
interval becomes shorter. However, the code limits re-computation
to 10ms intervals so that average frequency remains meaningful.
Discerning users are encouraged to take advantage of
the turbostat(8) utility, which can gracefully handle
concurrent measurement intervals of arbitrary length.
Signed-off-by: Len Brown <len.brown@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
In the current model the max/min perf limits are a fraction of current
user space limits to the allowed max_freq or 100% for global limits.
This results in wrong ratio limits calculation because of rounding
issues for some user space limits.
Initially we tried to solve this issue by issue by having more shift
bits to increase precision. Still there are isolated cases where we still
have error.
This can be avoided by using ratios all together. Since the way we get
cpuinfo.max_freq is by multiplying scaling factor to max ratio, we can
easily keep the max/min ratios in terms of ratios and not fractions.
For example:
if the max ratio = 36
cpuinfo.max_freq = 36 * 100000 = 3600000
Suppose user space sets a limit of 1200000, then we can calculate
max ratio limit as
= 36 * 1200000 / 3600000
= 12
This will be correct for any user limits.
The other advantage is that, we don't need to do any calculation in the
fast path as ratio limit is already calculated via set_policy() callback.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
pointer freq_table can be made static as it does not need to be in
global scope.
Cleans up sparse warning:
"symbol 'freq_table' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix inconsistent indenting and unneeded white space in assignment.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This fixes an issue with imx6ull where setting the frequency to 528Mhz
would actually set the ARM clock to 324Mhz.
Signed-off-by: Octavian Purdila <octavian.purdila@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add the compatible string for supporting the generic device tree cpufreq-dt
driver on Hisilicon's 3660 SoC.
Signed-off-by: Tao Wang <kevin.wangtao@hisilicon.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Conflicts:
kernel/sched/Makefile
Pick up the waitqueue related renames - it didn't get much feedback,
so it appears to be uncontroversial. Famous last words? ;-)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
SCPI update for v4.13
Adds support to get DVFS transition latency and OPP for any device whose
DVFS are managed by SCPI. This avoids code duplication in both cpufreq
and devfreq SCPI drivers.
* tag 'scpi-updates-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
cpufreq: scpi: use new scpi_ops functions to remove duplicate code
firmware: arm_scpi: add support to populate OPPs and get transition latency
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* pm-cpufreq:
cpufreq: conservative: Allow down_threshold to take values from 1 to 10
Revert "cpufreq: schedutil: Reduce frequencies slower"
* pm-cpuidle:
cpuidle: dt: Add missing 'of_node_put()'
* pm-devfreq:
PM / devfreq: exynos-ppmu: Staticize event list
PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable
|
|
Commit 27ed3cd2ebf4 (cpufreq: conservative: Fix the logic in frequency
decrease checking) removed the 10 point substraction when comparing the
load against down_threshold but did not remove the related limit for the
down_threshold value. As a result, down_threshold lower than 11 is not
allowed even though values from 1 to 10 do work correctly too. The
comment ("cannot be lower than 11 otherwise freq will not fall") also
does not apply after removing the substraction.
For this reason, allow down_threshold to take any value from 1 to 99
and fix the related comment.
Fixes: 27ed3cd2ebf4 (cpufreq: conservative: Fix the logic in frequency decrease checking)
Signed-off-by: Tomasz Wilczyński <twilczynski@naver.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* intel_pstate:
cpufreq: intel_pstate: Avoid division by 0 in min_perf_pct_min()
* pm-sleep:
Revert "ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle"
|
|
Commit c5a2ee7dde89 (cpufreq: intel_pstate: Active mode P-state
limits rework) incorrectly assumed that pstate.turbo_pstate would
always be nonzero for CPU0 in min_perf_pct_min() if
cpufreq_register_driver() had succeeded which may not be the case
in virtualized environments.
If that assumption doesn't hold, it leads to an early crash on boot
in intel_pstate_register_driver(), so add a sanity check to
min_perf_pct_min() to prevent the crash from happening.
Fixes: c5a2ee7dde89 (cpufreq: intel_pstate: Active mode P-state limits rework)
Reported-and-tested-by: Jongman Heo <jongman.heo@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
scpi_ops now provide APIs to get the transition_latency and to add
OPPs to the devices making those logic redundant here.
This patch makes use of those APIs and removes the redundant code in
this driver.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
* pm-cpufreq:
cpufreq: kirkwood-cpufreq:- Handle return value of clk_prepare_enable()
cpufreq: cpufreq_register_driver() should return -ENODEV if init fails
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For a driver that does not set the CPUFREQ_STICKY flag, if all of the
->init() calls fail, cpufreq_register_driver() should return an error.
This will prevent the driver from loading.
Fixes: ce1bcfe94db8 (cpufreq: check cpufreq_policy_list instead of scanning policies for all CPUs)
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Signed-off-by: David Arcari <darcari@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We need such a routine at two places already, lets create one.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The CPU cooling driver uses the cpufreq policy, to get clip_cpus, the
frequency table, etc. Most of the callers of CPU cooling driver's
registration routines have the cpufreq policy with them, but they only
pass the policy->related_cpus cpumask. The __cpufreq_cooling_register()
routine then gets the policy by itself and uses it.
It would be much better if the callers can pass the policy instead
directly. This also fixes a basic design flaw, where the policy can be
freed while the CPU cooling driver is still active.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
cpufreq holds get_online_cpus() while invoking cpuhp_setup_state_nocalls()
to make subsys_interface_register() and the registration of hotplug calls
atomic versus cpu hotplug.
cpuhp_setup_state_nocalls() invokes get_online_cpus() as well. This is
correct, but prevents the conversion of the hotplug locking to a percpu
rwsem.
Use cpuhp_setup/remove_state_nocalls_cpuslocked() to avoid the nested
call. Convert *_online_cpus() to the new interfaces while at it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170524081547.731628408@linutronix.de
|
|
To enable smp_processor_id() and might_sleep() debug checks earlier, it's
required to add system states between SYSTEM_BOOTING and SYSTEM_RUNNING.
Adjust the system_state check in pas_cpufreq_cpu_exit() to handle the extra
states.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20170516184735.620023128@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
* intel_pstate:
cpufreq: intel_pstate: Document the current behavior and user interface
* pm-cpufreq:
cpufreq: dbx500: add a Kconfig symbol
* pm-cpufreq-sched:
cpufreq: schedutil: use now as reference when aggregating shared policy requests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull power management utilities updates from Len Brown.
* 'utilities' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
intel_pstate: use updated msr-index.h HWP.EPP values
tools/power x86_energy_perf_policy: support HWP.EPP
x86: msr-index.h: fix shifts to ULL results in HWP macros.
x86: msr-index.h: define HWP.EPP values
x86: msr-index.h: define EPB mid-points
|
|
Moving the cooling code into the cpufreq driver caused a possible build failure
when the cpu_thermal helper code is a loadable module or disabled:
drivers/cpufreq/dbx500-cpufreq.o: In function `dbx500_cpufreq_ready':
dbx500-cpufreq.c:(.text.dbx500_cpufreq_ready+0x4): undefined reference to `cpufreq_cooling_register'
This adds the same dependency that we have in other cpufreq drivers,
forcing the driver to be disabled when we can't possibly link it.
Fixes: 19678ffb9fd6 (cpufreq: dbx500: Manage cooling device from cpufreq driver)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull MIPS updates from James Hogan:
"math-emu:
- Add missing clearing of BLTZALL and BGEZALL emulation counters
- Fix BC1EQZ and BC1NEZ condition handling
- Fix BLEZL and BGTZL identification
BPF:
- Add JIT support for SKF_AD_HATYPE
- Use unsigned access for unsigned SKB fields
- Quit clobbering callee saved registers in JIT code
- Fix multiple problems in JIT skb access helpers
Loongson 3:
- Select MIPS_L1_CACHE_SHIFT_6
Octeon:
- Remove vestiges of CONFIG_CAVIUM_OCTEON_2ND_KERNEL
- Remove unused L2C types and macros.
- Remove unused SLI types and macros.
- Fix compile error when USB is not enabled.
- Octeon: Remove unused PCIERCX types and macros.
- Octeon: Clean up platform code.
SNI:
- Remove recursive include of cpu-feature-overrides.h
Sibyte:
- Export symbol periph_rev to sb1250-mac network driver.
- Fix Kconfig warning.
Generic platform:
- Enable Root FS on NFS in generic_defconfig
SMP-MT:
- Use CPU interrupt controller IPI IRQ domain support
UASM:
- Add support for LHU for uasm.
- Remove needless ISA abstraction
mm:
- Add 48-bit VA space and 4-level page tables for 4K pages.
PCI:
- Add controllers before the specified head
irqchip driver for MIPS CPU:
- Replace magic 0x100 with IE_SW0
- Prepare for non-legacy IRQ domains
- Introduce IPI IRQ domain support
MAINTAINERS:
- Update email-id of Rahul Bedarkar
NET:
- sb1250-mac: Add missing MODULE_LICENSE()
CPUFREQ:
- Loongson2: drop set_cpus_allowed_ptr()
Misc:
- Disable Werror when W= is set
- Opt into HAVE_COPY_THREAD_TLS
- Enable GENERIC_CPU_AUTOPROBE
- Use common outgoing-CPU-notification code
- Remove dead define of ST_OFF
- Remove CONFIG_ARCH_HAS_ILOG2_U{32,64}
- Stengthen IPI IRQ domain sanity check
- Remove confusing else statement in __do_page_fault()
- Don't unnecessarily include kmalloc.h into <asm/cache.h>.
- Delete unused definition of SMP_CACHE_SHIFT.
- Delete redundant definition of SMP_CACHE_BYTES"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (39 commits)
MIPS: Sibyte: Fix Kconfig warning.
MIPS: Sibyte: Export symbol periph_rev to sb1250-mac network driver.
NET: sb1250-mac: Add missing MODULE_LICENSE()
MAINTAINERS: Update email-id of Rahul Bedarkar
MIPS: Remove confusing else statement in __do_page_fault()
MIPS: Stengthen IPI IRQ domain sanity check
MIPS: smp-mt: Use CPU interrupt controller IPI IRQ domain support
irqchip: mips-cpu: Introduce IPI IRQ domain support
irqchip: mips-cpu: Prepare for non-legacy IRQ domains
irqchip: mips-cpu: Replace magic 0x100 with IE_SW0
MIPS: Remove CONFIG_ARCH_HAS_ILOG2_U{32,64}
MIPS: generic: Enable Root FS on NFS in generic_defconfig
MIPS: mach-rm: Remove recursive include of cpu-feature-overrides.h
MIPS: Opt into HAVE_COPY_THREAD_TLS
CPUFREQ: Loongson2: drop set_cpus_allowed_ptr()
MIPS: uasm: Remove needless ISA abstraction
MIPS: Remove dead define of ST_OFF
MIPS: Use common outgoing-CPU-notification code
MIPS: math-emu: Fix BC1EQZ and BC1NEZ condition handling
MIPS: r2-on-r6-emu: Clear BLTZALL and BGEZALL debugfs counters
...
|
|
intel_pstate exports sysfs attributes for setting and observing HWP.EPP.
These attributes use strings to describe 4 operating states, and
inside the driver, these strings are mapped to numerical register
values.
The authorative mapping between the strings and numerical HWP.EPP values
are now globally defined in msr-index.h, replacing the out-dated
mapping that were open-coded into intel_pstate.c
new old string
--- --- ------
0 0 performance
128 64 balance_performance
192 128 balance_power
255 192 power
Note that the HW and BIOS default value on most system is 128,
which intel_pstate will now call "balance_performance"
while it used to call it "balance_power".
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
|
|
While examining output from trial builds with -Wformat-security enabled,
many strings were found that should be defined as "const", or as a char
array instead of char pointer. This makes some static analysis easier,
by producing fewer false positives.
As these are all trivial changes, it seemed best to put them all in a
single patch rather than chopping them up per maintainer.
Link: http://lkml.kernel.org/r/20170405214711.GA5711@beast
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jes Sorensen <jes@trained-monkey.org> [runner.c]
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kejian Yan <yankejian@huawei.com>
Cc: Daode Huang <huangdaode@hisilicon.com>
Cc: Qianqian Xie <xieqianqian@huawei.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Christian Gromm <christian.gromm@microchip.com>
Cc: Andrey Shvetsov <andrey.shvetsov@k2l.de>
Cc: Jason Litzinger <jlitzingerdev@gmail.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- another round of rq-clock handling debugging, robustization and
fixes
- PELT accounting improvements
- CPU hotplug related ->cpus_allowed affinity handling fixes all
around the tree
- ... plus misc fixes, cleanups and updates"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (35 commits)
sched/x86: Update reschedule warning text
crypto: N2 - Replace racy task affinity logic
cpufreq/sparc-us2e: Replace racy task affinity logic
cpufreq/sparc-us3: Replace racy task affinity logic
cpufreq/sh: Replace racy task affinity logic
cpufreq/ia64: Replace racy task affinity logic
ACPI/processor: Replace racy task affinity logic
ACPI/processor: Fix error handling in __acpi_processor_start()
sparc/sysfs: Replace racy task affinity logic
powerpc/smp: Replace open coded task affinity logic
ia64/sn/hwperf: Replace racy task affinity logic
ia64/salinfo: Replace racy task affinity logic
workqueue: Provide work_on_cpu_safe()
ia64/topology: Remove cpus_allowed manipulation
sched/fair: Move the PELT constants into a generated header
sched/fair: Increase PELT accuracy for small tasks
sched/fair: Fix comments
sched/Documentation: Add 'sched-pelt' tool
sched/fair: Fix corner case in __accumulate_sum()
sched/core: Remove 'task' parameter and rename tsk_restore_flags() to current_restore_flags()
...
|
