| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
After commit aa7519af450d (cpufreq: Use transition_delay_us for legacy
governors as well) the sampling_rate field of struct dbs_data may be
less than the tick period which causes dbs_update() to produce
incorrect results, so make the code ensure that the value of that
field will always be sufficiently large.
Fixes: aa7519af450d (cpufreq: Use transition_delay_us for legacy governors as well)
Reported-by: Andy Tang <andy.tang@nxp.com>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Andy Tang <andy.tang@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The commit moving the speed grading check to the cpufreq driver introduced
some additional checks, so the OPP disable is only attempted on SoCs where
those OPPs are present. The compatible checks are missing the QuadPlus
compatible, so invalid OPPs are not correctly disabled there.
Move both checks to a single condition, so we don't need to sprinkle even
more calls to of_machine_is_compatible().
Fixes: 2b3d58a3adca (cpufreq: imx6q: Move speed grading check to cpufreq driver)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/cpufreq/mediatek-cpufreq.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The MIPS loongson cpufreq drivers don't build unless configured for the
correct machine type, due to dependency on machine specific architecture
headers and symbols in machine specific platform code.
More specifically loongson1-cpufreq.c uses RST_CPU_EN and RST_CPU,
neither of which is defined in asm/mach-loongson32/regs-clk.h unless
CONFIG_LOONGSON1_LS1B=y, and loongson2_cpufreq.c references
loongson2_clockmod_table[], which is only defined in
arch/mips/loongson64/lemote-2f/clock.c, i.e. when
CONFIG_LEMOTE_MACH2F=y.
Add these dependencies to Kconfig to avoid randconfig / allyesconfig
build failures (e.g. when based on BMIPS which also has a cpufreq
driver).
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are no real big ticket items here this time.
The most noticeable change is probably the relocation of the OPP
(Operating Performance Points) framework to its own directory under
drivers/ as it has grown big enough for that. Also Viresh is now going
to maintain it and send pull requests for it to me, so you will see
this change in the git history going forward (but still not right
now).
Another noticeable set of changes is the modifications of the PM core,
the PCI subsystem and the ACPI PM domain to allow of more integration
between system-wide suspend/resume and runtime PM. For now it's just a
way to avoid resuming devices from runtime suspend unnecessarily
during system suspend (if the driver sets a flag to indicate its
readiness for that) and in the works is an analogous mechanism to
allow devices to stay suspended after system resume.
In addition to that, we have some changes related to supporting
frequency-invariant CPU utilization metrics in the scheduler and in
the schedutil cpufreq governor on ARM and changes to add support for
device performance states to the generic power domains (genpd)
framework.
The rest is mostly fixes and cleanups of various sorts.
Specifics:
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume and
clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler on
ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core and
drop legacy bus type suspend and resume callbacks from ARM/locomo
(Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up somewhat
(Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle) residency
counter based on the LPIT ACPI table on Intel platforms (Srinivas
Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the notifier
removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use stale
cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing wakeup
events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent the PM
core from using the direct-complete optimization with it as that is
guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit (Gaurav
Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it up
(Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in the
cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches, Rafael
Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava, Shuah
Khan)"
* tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (88 commits)
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
intel_idle: Graceful probe failure when MWAIT is disabled
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpuidle: Avoid assignment in if () argument
cpuidle: Clean up cpuidle_enable_device() error handling a bit
ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
cpuidle: ladder: Add per CPU PM QoS resume latency support
PM / QoS: Fix device resume latency framework
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
|
|
* pm-cpufreq: (22 commits)
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpufreq: pxa: convert to clock API
cpufreq: speedstep-lib: mark expected switch fall-through
cpufreq: ti-cpufreq: add missing of_node_put()
cpufreq: dt: Remove support for Exynos4212 SoCs
cpufreq: imx6q: Move speed grading check to cpufreq driver
cpufreq: ti-cpufreq: kfree opp_data when failure
cpufreq: SPEAr: pr_err() strings should end with newlines
cpufreq: powernow-k8: pr_err() strings should end with newlines
cpufreq: dt-platdev: drop socionext,uniphier-ld6b from whitelist
arm64: wire cpu-invariant accounting support up to the task scheduler
arm64: wire frequency-invariant accounting support up to the task scheduler
arm: wire cpu-invariant accounting support up to the task scheduler
arm: wire frequency-invariant accounting support up to the task scheduler
drivers base/arch_topology: allow inlining cpu-invariant accounting support
drivers base/arch_topology: provide frequency-invariant accounting support
cpufreq: dt: invoke frequency-invariance setter function
cpufreq: arm_big_little: invoke frequency-invariance setter function
...
|
|
On platforms with large number of Pstates, the transition table, which
is a NxN matrix, can overflow beyond the PAGE_SIZE boundary.
This can be seen on POWER9 which has 100+ Pstates.
As a result, each time the trans_table is read for any of the CPUs, we
will get the following error.
---------------------------------------------------
fill_read_buffer: show+0x0/0xa0 returned bad count
---------------------------------------------------
This patch ensures that in case of an overflow, we print a warning
once in the dmesg and return FILE TOO LARGE error for this and all
subsequent accesses of trans_table.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make these const as they are only getting passed to the functions
bL_cpufreq_{register/unregister} having the arguments as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make the arguments of functions bL_cpufreq_{register/unregister} as
const as the ops pointer does not modify the fields of the
cpufreq_arm_bL_ops structure it points to. The pointer arm_bL_ops is
also getting initialized with ops but the pointer does not modify the
fields. So, make the function argument and the structure pointer const.
Add const to function prototypes too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As the clock settings have been introduced into the clock pxa drivers,
which are now available to change the CPU clock by themselves, remove
the clock handling from this driver, and rely on pxa clock drivers.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
call of_node_put to release the refcount of np.
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Support for Exynos4212 SoCs has been removed by commit bca9085e0ae9
"ARM: dts: exynos: remove Exynos4212 support (dead code)", so there
is no need to keep remaining dead code related to this SoC version.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On some i.MX6 SoCs (like i.MX6SL, i.MX6SX and i.MX6UL) that do not have
speed grading check, opp table will not be created in platform code,
so cpufreq driver prints the following error message:
cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19)
However, this is not really an error in this case because the
imx6q-cpufreq driver first calls dev_pm_opp_get_opp_count()
and if it fails, it means that platform code does not provide
OPP and then dev_pm_opp_of_add_table() will be called.
In order to avoid such confusing error message, move the speed grading
check from platform code to the imx6q-cpufreq driver.
This way the imx6q-cpufreq no longer has to check whether OPP table
is supplied by platform code.
Tested on a i.MX6Q and i.MX6UL based boards.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This refactors the only user of init_timer_pinned_deferrable() to use the
new timer_setup() and from_timer(). Adds a pointer back to the policy,
and drops the definition of init_timer_pinned_deferrable().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Petr Mladek <pmladek@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: linux1394-devel@lists.sourceforge.net
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-s390@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Harish Patil <harish.patil@cavium.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Manish Chopra <manish.chopra@cavium.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-pm@vger.kernel.org
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Mark Gross <mark.gross@intel.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Michael Reed <mdr@sgi.com>
Cc: netdev@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lkml.kernel.org/r/1507159627-127660-3-git-send-email-keescook@chromium.org
|
|
memory leakage was found by kmemleak. opp_data needs to be freed
when failure, including fail_put_node.
unreferenced object 0xccdd4c40 (size 64):
comm "swapper", pid 1, jiffies 4294938465 (age 888.520s)
hex dump (first 32 bytes):
00 7c 00 c1 98 69 d8 ce 00 24 03 ce 00 24 03 ce .|...i...$...$..
20 35 23 c1 00 00 00 00 00 00 00 00 00 00 00 00 5#.............
backtrace:
[<c028fb64>] kmem_cache_alloc_trace+0x2c4/0x3cc
[<c076d5f0>] ti_cpufreq_probe+0x6c/0x334
[<c068d6e4>] platform_drv_probe+0x60/0xc0
[<c068b384>] driver_probe_device+0x218/0x2c4
[<c068b5a4>] __device_attach_driver+0xa8/0xdc
[<c0689340>] bus_for_each_drv+0x70/0xa4
[<c068b020>] __device_attach+0xc0/0x124
[<c068b634>] device_initial_probe+0x1c/0x20
[<c068a3b8>] bus_probe_device+0x94/0x9c
[<c0688300>] device_add+0x404/0x590
[<c068d408>] platform_device_add+0x11c/0x230
[<c068df40>] platform_device_register_full+0x10c/0x128
[<c076d578>] ti_cpufreq_init+0x44/0x50
[<c01017c4>] do_one_initcall+0x54/0x180
[<c0e00fe0>] kernel_init_freeable+0x270/0x33c
[<c093f2bc>] kernel_init+0x18/0x124
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
pr_err() messages should terminated with a new-line to avoid
other messages being concatenated onto the end.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
pr_err() messages should terminated with a new-line to avoid
other messages being concatenated onto the end.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As you see arch/arm/boot/dts/uniphier-ld6b.dtsi, it includes
uniphier-pxs2.dtsi, which uses "operating-points-v2" property
and whose cpufreq device is automatically created.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Call the frequency-invariance setter function arch_set_freq_scale()
if the new frequency has been successfully set which is indicated by
dev_pm_opp_set_rate() returning 0.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Call the frequency-invariance setter function arch_set_freq_scale()
if the new frequency has been successfully set which is indicated by
bL_cpufreq_set_rate() returning 0.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Frequency-invariant accounting support based on the ratio of current
frequency and maximum supported frequency is an optional feature an arch
can implement.
Since there are cpufreq drivers (e.g. cpufreq-dt) which can be build for
different arch's a default implementation of the frequency-invariance
setter function arch_set_freq_scale() is needed.
This default implementation is an empty weak function which will be
overwritten by a strong function in case the arch provides one.
The setter function passes the cpumask of related (to the frequency
change) cpus (online and offline cpus), the (new) current frequency and
the maximum supported frequency.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ti-cpufreq and cpufreq-dt-platdev drivers are registering platform-device
with same name "cpufreq-dt" using platform_device_register_*() routines.
This is leading to build warnings appended below.
Providing hardware information to OPP framework along with the platform-
device creation should be done by ti-cpufreq driver before cpufreq-dt
driver comes into place.
This patch add's TI am33xx, am43 and dra7 platforms (which use opp-v2
property) to the blacklist of devices in cpufreq-dt-platform driver to
avoid creating platform-device twice and remove build warnings.
[ 2.370167] ------------[ cut here ]------------
[ 2.375087] WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x58/0x78
[ 2.383112] sysfs: cannot create duplicate filename '/devices/platform/cpufreq-dt'
[ 2.391219] Modules linked in:
[ 2.394506] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.13.0-next-20170912 #1
[ 2.402006] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 2.408437] [<c0110a28>] (unwind_backtrace) from [<c010ca84>] (show_stack+0x10/0x14)
[ 2.416568] [<c010ca84>] (show_stack) from [<c0827d64>] (dump_stack+0xac/0xe0)
[ 2.424165] [<c0827d64>] (dump_stack) from [<c0137470>] (__warn+0xd8/0x104)
[ 2.431488] [<c0137470>] (__warn) from [<c01374d0>] (warn_slowpath_fmt+0x34/0x44)
[ 2.439351] [<c01374d0>] (warn_slowpath_fmt) from [<c03459d0>] (sysfs_warn_dup+0x58/0x78)
[ 2.447938] [<c03459d0>] (sysfs_warn_dup) from [<c0345ab8>] (sysfs_create_dir_ns+0x80/0x98)
[ 2.456719] [<c0345ab8>] (sysfs_create_dir_ns) from [<c082c554>] (kobject_add_internal+0x9c/0x2d4)
[ 2.466124] [<c082c554>] (kobject_add_internal) from [<c082c7d8>] (kobject_add+0x4c/0x9c)
[ 2.474712] [<c082c7d8>] (kobject_add) from [<c05803e4>] (device_add+0xcc/0x57c)
[ 2.482489] [<c05803e4>] (device_add) from [<c0584b74>] (platform_device_add+0x100/0x220)
[ 2.491085] [<c0584b74>] (platform_device_add) from [<c05855a8>] (platform_device_register_full+0xf4/0x118)
[ 2.501305] [<c05855a8>] (platform_device_register_full) from [<c067023c>] (ti_cpufreq_init+0x150/0x22c)
[ 2.511253] [<c067023c>] (ti_cpufreq_init) from [<c0101df4>] (do_one_initcall+0x3c/0x170)
[ 2.519838] [<c0101df4>] (do_one_initcall) from [<c0c00eb4>] (kernel_init_freeable+0x1fc/0x2c4)
[ 2.528974] [<c0c00eb4>] (kernel_init_freeable) from [<c083bcac>] (kernel_init+0x8/0x110)
[ 2.537565] [<c083bcac>] (kernel_init) from [<c0107d18>] (ret_from_fork+0x14/0x3c)
[ 2.545981] ---[ end trace 2fc00e213c13ab20 ]---
[ 2.551051] ------------[ cut here ]------------
[ 2.555931] WARNING: CPU: 0 PID: 1 at lib/kobject.c:240 kobject_add_internal+0x254/0x2d4
[ 2.564578] kobject_add_internal failed for cpufreq-dt with -EEXIST, don't try to register
things with the same name in the same directory.
[ 2.577977] Modules linked in:
[ 2.581261] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.13.0-next-20170912 #1
[ 2.590013] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 2.596437] [<c0110a28>] (unwind_backtrace) from [<c010ca84>] (show_stack+0x10/0x14)
[ 2.604573] [<c010ca84>] (show_stack) from [<c0827d64>] (dump_stack+0xac/0xe0)
[ 2.612172] [<c0827d64>] (dump_stack) from [<c0137470>] (__warn+0xd8/0x104)
[ 2.619494] [<c0137470>] (__warn) from [<c01374d0>] (warn_slowpath_fmt+0x34/0x44)
[ 2.627362] [<c01374d0>] (warn_slowpath_fmt) from [<c082c70c>] (kobject_add_internal+0x254/0x2d4)
[ 2.636666] [<c082c70c>] (kobject_add_internal) from [<c082c7d8>] (kobject_add+0x4c/0x9c)
[ 2.645255] [<c082c7d8>] (kobject_add) from [<c05803e4>] (device_add+0xcc/0x57c)
[ 2.653027] [<c05803e4>] (device_add) from [<c0584b74>] (platform_device_add+0x100/0x220)
[ 2.661615] [<c0584b74>] (platform_device_add) from [<c05855a8>] (platform_device_register_full+0xf4/0x118)
[ 2.671833] [<c05855a8>] (platform_device_register_full) from [<c067023c>] (ti_cpufreq_init+0x150/0x22c)
[ 2.681779] [<c067023c>] (ti_cpufreq_init) from [<c0101df4>] (do_one_initcall+0x3c/0x170)
[ 2.690377] [<c0101df4>] (do_one_initcall) from [<c0c00eb4>] (kernel_init_freeable+0x1fc/0x2c4)
[ 2.699510] [<c0c00eb4>] (kernel_init_freeable) from [<c083bcac>] (kernel_init+0x8/0x110)
[ 2.708106] [<c083bcac>] (kernel_init) from [<c0107d18>] (ret_from_fork+0x14/0x3c)
[ 2.716217] ---[ end trace 2fc00e213c13ab21 ]---
Fixes: edeec420de24 (cpufreq: dt-cpufreq: platdev Automatically create device with OPP v2)
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rather than letting the ti-cpufreq driver match against 'ti,am4372'
machine compatible during probe let's match against 'ti,am43' so that we
can support both 'ti,am4372' and 'ti,am438x' platforms which both match
to this compatible.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit edeec420de24 (cpufreq: dt-platdev: Automatically create cpufreq
device with OPP v2) missed adding few platforms to the blacklist which
create the cpufreq-dt device from their own drivers, after some
dependencies are sorted out.
And for those platforms, both the platform specific driver and the
cpufreq-dt-platdev driver try to create the cpufreq-dt device now.
Fix that by including those platforms in the blacklist. This doesn't include
the TI platforms, for which there is a separate patch.
Fixes: edeec420de24 (cpufreq: dt-cpufreq: platdev Automatically create device with OPP v2)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These include a usual ACPICA code update (this time to upstream
revision 20170728), a fix for a boot crash on some systems with
Thunderbolt devices connected at boot time, a rework of the handling
of PCI bridges when setting up device wakeup, new support for Apple
device properties, support for DMA configurations reported via ACPI on
ARM64, APEI-related updates, ACPI EC driver updates and assorted minor
modifications in several places.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170728
including:
* Alias operator handling update (Bob Moore).
* Deferred resolution of reference package elements (Bob Moore).
* Support for the _DMA method in walk resources (Bob Moore).
* Tables handling update and support for deferred table
verification (Lv Zheng).
* Update of SMMU models for IORT (Robin Murphy).
* Compiler and disassembler updates (Alex James, Erik Schmauss,
Ganapatrao Kulkarni, James Morse).
* Tools updates (Erik Schmauss, Lv Zheng).
* Assorted minor fixes and cleanups (Bob Moore, Kees Cook, Lv
Zheng, Shao Ming).
- Rework the initialization of non-wakeup GPEs with method handlers
in order to address a boot crash on some systems with Thunderbolt
devices connected at boot time where we miss an early hotplug event
due to a delay in GPE enabling (Rafael Wysocki).
- Rework the handling of PCI bridges when setting up ACPI-based
device wakeup in order to avoid disabling wakeup for bridges
prematurely (Rafael Wysocki).
- Consolidate Apple DMI checks throughout the tree, add support for
Apple device properties to the device properties framework and use
these properties for the handling of I2C and SPI devices on Apple
systems (Lukas Wunner).
- Add support for _DMA to the ACPI-based device properties lookup
code and make it possible to use the information from there to
configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
- Fix several issues in the APEI code, add support for exporting the
BERT error region over sysfs and update APEI MAINTAINERS entry with
reviewers information (Borislav Petkov, Dongjiu Geng, Loc Ho, Punit
Agrawal, Tony Luck, Yazen Ghannam).
- Fix a potential initialization ordering issue in the ACPI EC driver
and clean it up somewhat (Lv Zheng).
- Update the ACPI SPCR driver to extend the existing XGENE 8250
workaround in it to a new platform (m400) and to work around an
Xgene UART clock issue (Graeme Gregory).
- Add a new utility function to the ACPI core to support using ACPI
OEM ID / OEM Table ID / Revision for system identification in
blacklisting or similar and switch over the existing code already
using this information to this new interface (Toshi Kani).
- Fix an xpower PMIC issue related to GPADC reads that always return
0 without extra pin manipulations (Hans de Goede).
- Add statements to print debug messages in a couple of places in the
ACPI core for easier diagnostics (Rafael Wysocki).
- Clean up the ACPI processor driver slightly (Colin Ian King, Hanjun
Guo).
- Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
- Add a quirk for Dell OptiPlex 9020M to the ACPI backlight driver
(Alex Hung).
- Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
Ronald Tschalär, Sumeet Pawnikar)"
* tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
ACPI / APEI: Suppress message if HEST not present
intel_pstate: convert to use acpi_match_platform_list()
ACPI / blacklist: add acpi_match_platform_list()
ACPI, APEI, EINJ: Subtract any matching Register Region from Trigger resources
ACPI: make device_attribute const
ACPI / sysfs: Extend ACPI sysfs to provide access to boot error region
ACPI: APEI: fix the wrong iteration of generic error status block
ACPI / processor: make function acpi_processor_check_duplicates() static
ACPI / EC: Clean up EC GPE mask flag
ACPI: EC: Fix possible issues related to EC initialization order
ACPI / PM: Add debug statements to acpi_pm_notify_handler()
ACPI: Add debug statements to acpi_global_event_handler()
ACPI / scan: Enable GPEs before scanning the namespace
ACPICA: Make it possible to enable runtime GPEs earlier
ACPICA: Dispatch active GPEs at init time
ACPI: SPCR: work around clock issue on xgene UART
ACPI: SPCR: extend XGENE 8250 workaround to m400
ACPI / LPSS: Don't abort ACPI scan on missing mem resource
mailbox: pcc: Drop uninformative output during boot
ACPI/IORT: Add IORT named component memory address limits
...
|
|
* intel_pstate:
cpufreq: intel_pstate: Shorten a couple of long names
cpufreq: intel_pstate: Simplify intel_pstate_adjust_pstate()
cpufreq: intel_pstate: Improve IO performance with per-core P-states
cpufreq: intel_pstate: Drop INTEL_PSTATE_HWP_SAMPLING_INTERVAL
cpufreq: intel_pstate: Drop ->update_util from pstate_funcs
cpufreq: intel_pstate: Do not use PID-based P-state selection
|
|
* pm-cpufreq-sched:
cpufreq: schedutil: Always process remote callback with slow switching
cpufreq: schedutil: Don't restrict kthread to related_cpus unnecessarily
cpufreq: Return 0 from ->fast_switch() on errors
cpufreq: Simplify cpufreq_can_do_remote_dvfs()
cpufreq: Process remote callbacks from any CPU if the platform permits
sched: cpufreq: Allow remote cpufreq callbacks
cpufreq: schedutil: Use unsigned int for iowait boost
cpufreq: schedutil: Make iowait boost more energy efficient
|
|
* pm-cpufreq: (33 commits)
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpufreq: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
cpufreq: dbx500: Delete obsolete driver
mfd: db8500-prcmu: Get rid of cpufreq dependency
cpufreq: enable the DT cpufreq driver on the Ux500
cpufreq: Loongson2: constify platform_device_id
cpufreq: dt: Add r8a7796 support to to use generic cpufreq driver
cpufreq: remove setting of policy->cpu in policy->cpus during init
cpufreq: mediatek: add support of cpufreq to MT7622 SoC
cpufreq: mediatek: add cleanups with the more generic naming
cpufreq: rcar: Add support for R8A7795 SoC
cpufreq: dt: Add rk3328 compatible to use generic cpufreq driver
cpufreq: s5pv210: add missing of_node_put()
cpufreq: Allow dynamic switching with CPUFREQ_ETERNAL latency
...
|
|
Convert to use acpi_match_platform_list() for the platform check.
There is no change in functionality.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch contains the minimal changes required to support imx6sx OPP
of 198 Mhz. Without this patch cpufreq still reports success but the
frequency is not changed, the "arm" clock will still be at 396000000 in
clk_summary.
In order to do this PLL1 needs to be still kept enabled while changing
the ARM clock. This is a hardware requirement: when ARM_PODF is changed
in CCM we need to check the busy bit of CCM_CDHIPR bit 16 arm_podf_busy,
and this bit is sync with PLL1 clock, so if PLL1 NOT enabled, this
bit will never get clear.
Keep pll1_sys explicitly enabled until after the rate is change to deal
with this. Otherwise from the clk framework perspective pll1_sys is
unused and gets turned off.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Don't populate arrays on the stack, instead make them static.
Makes the object code smaller by over 860 bytes:
Before:
text data bss dec hex filename
10716 5196 0 15912 3e28 drivers/cpufreq/speedstep-lib.o
After:
text data bss dec hex filename
9690 5356 0 15046 3ac6 drivers/cpufreq/speedstep-lib.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If 'dev_pm_opp_set_supported_hw()' fails, 'opp_data->opp_node' refcount
will be decremented 2 times.
One, just a few lines above, and another one in the error handling path.
Fix it by simply moving the 'of_node_put' call of the normal path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Drop few ARM (32 and 64 bit) platforms from the whitelist which always
use "operating-points-v2" property from their DT. They should continue
to work after this patch.
Tested on Hikey platform (only the "hisilicon,hi6220" entry).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The initial idea of creating the cpufreq-dt-platdev.c file was to keep a
list of platforms that use the "operating-points" (V1) bindings and
create cpufreq device for them only, as we weren't sure which platforms
would want the device to get created automatically as some had their own
cpufreq drivers as well, or wanted to initialize cpufreq after doing
some stuff from platform code.
But that wasn't the case with platforms using "operating-points-v2"
property. We wanted the device to get created automatically without the
need of adding them to the whitelist. Though, we will still have some
exceptions where we don't want to create the device automatically.
Rename the earlier platform list as *whitelist* and create a new
*blacklist* as well.
The cpufreq-dt device will get created if:
- The platform is there in the whitelist OR
- The platform has "operating-points-v2" property in CPU0's DT node and
isn't part of the blacklist .
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If transition_delay_us isn't defined by the cpufreq driver, the default
value of transition delay (time after which the cpufreq governor will
try updating the frequency again) is currently calculated by multiplying
transition_latency (nsec) with LATENCY_MULTIPLIER (1000) and then
converting this time to usec. That gives the exact same value as
transition_latency, just that the time unit is usec instead of nsec.
With acpi-cpufreq for example, transition_latency is set to around 10
usec and we get transition delay as 10 ms. Which seems to be a
reasonable amount of time to reevaluate the frequency again.
But for platforms where frequency switching isn't that fast (like ARM),
the transition_latency varies from 500 usec to 3 ms, and the transition
delay becomes 500 ms to 3 seconds. Of course, that is a pretty bad
default value to start with.
We can try to come across a better formula (instead of multiplying with
LATENCY_MULTIPLIER) to solve this problem, but will that be worth it ?
This patch tries a simple approach and caps the maximum value of default
transition delay to 10 ms. Of course, userspace can still come in and
change this value anytime or individual drivers can rather provide
transition_delay_us instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We have moved the Ux500 over to use the generic DT based
cpufreq driver, so delete the old custom driver.
At the same time select CPUFREQ_DT from the machine's
Kconfig in order to satisfy the "default ARCH_U8500"
selection on the old driver.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
This enables the generic DT and OPP-based cpufreq driver on the
ST-Ericsson Ux500 series.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch adds the r8a7796 support the generic cpufreq driver
by adding an appropriate compat string. This is in keeping
with support for other Renesas ARM and arm64 based SoCs.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@rvc.renesas.com>
[simon: new changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
policy->cpu is copied into policy->cpus in cpufreq_online() before
calling into cpufreq_driver->init(). So there's no need to set the
same in the individual driver init() functions again.
This patch removes the redundant setting of policy->cpu in policy->cpus
in intel_pstate and cppc drivers.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The intel_pstate CPU frequency scaling driver has always
calculated CPU frequency incorrectly. Recent changes have
eliminted most of the issues, however the frequency reported
in the trace buffer, if used, is incorrect.
It remains desireable that cpu->pstate.scaling still be a nice
round number for things such as when setting max and min frequencies.
So the proposal is to just fix the reported frequency in the trace data.
Fixes what remains of [1].
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96521 # [1]
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
MT7622 is a 64-bit ARMv8 based dual-core SoC (2 * Cortex-A53) with a
single cluster. The hardware is also compatible with the current driver,
so add MT7622 as one of the compatible string list.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since more MediaTek SoCs can be supported with the cpufreq driver and not
limited to MT8173, a couple of cleanups are done here with renaming those
functions and related structures with "mtk" instead of "mt8173".
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
CPUFREQ_ENTRY_INVALID is a special symbol which is used to specify that
an entry in the cpufreq table is invalid. But using it outside of the
scope of the cpufreq table looks a bit incorrect.
We can represent an invalid frequency by writing it as 0 instead if we
need. Note that it is already done that way for the return value of the
->get() callback.
Lets do the same for ->fast_switch() and not use CPUFREQ_ENTRY_INVALID
outside of the scope of cpufreq table.
Also update the comment over cpufreq_driver_fast_switch() to clearly
mention what this returns.
None of the drivers return CPUFREQ_ENTRY_INVALID as of now from
->fast_switch() callback and so we don't need to update any of those.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
