| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We can move the TI dmtimer clockevent and clocksource to live under
drivers/clocksource if we rely only on the clock framework, and handle
the module configuration directly in the clocksource driver based on the
device tree data.
This removes the early dependency with system timers to the interconnect
related code, and we can probe pretty much everything else later on at
the module_init level.
Let's first add a new driver for timer-ti-dm-systimer based on existing
arch/arm/mach-omap2/timer.c. Then let's start moving SoCs to probe with
device tree data while still keeping the old timer.c. And eventually we
can just drop the old timer.c.
Let's take the opportunity to switch to use readl/writel as pointed out
by Daniel Lezcano <daniel.lezcano@linaro.org>. This allows further
clean-up of the timer-ti-dm code the a lot of the shared helpers can
just become static to the non-syster related code.
Note the boards can optionally configure different timer source clocks
if needed with assigned-clocks and assigned-clock-parents.
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200507172330.18679-3-tony@atomide.com
|
|
OST is the OS Timer, a 64-bit timer/counter with buffered reading.
SoCs before the JZ4770 had (if any) a 32-bit OST; the JZ4770 and
JZ4780 have a 64-bit OST.
This driver will register both a clocksource and a sched_clock to the
system.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200212180408.30872-1-paul@crapouillou.net
|
|
Add driver for Microchip PIT64B timer. Timer could be used in continuous
mode or oneshot mode. The hardware has 2x32 bit registers for period
emulating a 64 bit timer. The LSB_PR and MSB_PR registers are used to
set the period value (compare value). TLSB and TMSB keeps the current
value of the counter. After a compare the TLSB and TMSB register resets.
The driver uses PIT64B timer for clocksource or clockevent. First
requested timer would be registered as clockevent, second one would be
registered as clocksource. Individual PIT64B hardware resources were
used for clocksource and clockevent to be able to support high resolution
timers with this hardware implementation.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1576235962-30123-3-git-send-email-claudiu.beznea@microchip.com
|
|
This driver handles the TCU (Timer Counter Unit) present on the Ingenic
JZ47xx SoCs, and provides the kernel with a system timer, a clocksource
and a sched_clock.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
|
|
Hyper-V clock/timer code and data structures are currently mixed
in with other code in the ISA independent drivers/hv directory as
well as the ISA dependent Hyper-V code under arch/x86.
Consolidate this code and data structures into a Hyper-V clocksource driver
to better follow the Linux model. In doing so, separate out the ISA
dependent portions so the new clocksource driver works for x86 and for the
in-process Hyper-V on ARM64 code.
To start, move the existing clockevents code to create the new clocksource
driver. Update the VMbus driver to call initialization and cleanup routines
since the Hyper-V synthetic timers are not independently enumerated in
ACPI.
No behavior is changed and no new functionality is added.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: "bp@alien8.de" <bp@alien8.de>
Cc: "will.deacon@arm.com" <will.deacon@arm.com>
Cc: "catalin.marinas@arm.com" <catalin.marinas@arm.com>
Cc: "mark.rutland@arm.com" <mark.rutland@arm.com>
Cc: "linux-arm-kernel@lists.infradead.org" <linux-arm-kernel@lists.infradead.org>
Cc: "gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>
Cc: "linux-hyperv@vger.kernel.org" <linux-hyperv@vger.kernel.org>
Cc: "olaf@aepfle.de" <olaf@aepfle.de>
Cc: "apw@canonical.com" <apw@canonical.com>
Cc: "jasowang@redhat.com" <jasowang@redhat.com>
Cc: "marcelo.cerri@canonical.com" <marcelo.cerri@canonical.com>
Cc: Sunil Muthuswamy <sunilmut@microsoft.com>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: "sashal@kernel.org" <sashal@kernel.org>
Cc: "vincenzo.frascino@arm.com" <vincenzo.frascino@arm.com>
Cc: "linux-arch@vger.kernel.org" <linux-arch@vger.kernel.org>
Cc: "linux-mips@vger.kernel.org" <linux-mips@vger.kernel.org>
Cc: "linux-kselftest@vger.kernel.org" <linux-kselftest@vger.kernel.org>
Cc: "arnd@arndb.de" <arnd@arndb.de>
Cc: "linux@armlinux.org.uk" <linux@armlinux.org.uk>
Cc: "ralf@linux-mips.org" <ralf@linux-mips.org>
Cc: "paul.burton@mips.com" <paul.burton@mips.com>
Cc: "daniel.lezcano@linaro.org" <daniel.lezcano@linaro.org>
Cc: "salyzyn@android.com" <salyzyn@android.com>
Cc: "pcc@google.com" <pcc@google.com>
Cc: "shuah@kernel.org" <shuah@kernel.org>
Cc: "0x7f454c46@gmail.com" <0x7f454c46@gmail.com>
Cc: "linux@rasmusvillemoes.dk" <linux@rasmusvillemoes.dk>
Cc: "huw@codeweavers.com" <huw@codeweavers.com>
Cc: "sfr@canb.auug.org.au" <sfr@canb.auug.org.au>
Cc: "pbonzini@redhat.com" <pbonzini@redhat.com>
Cc: "rkrcmar@redhat.com" <rkrcmar@redhat.com>
Cc: "kvm@vger.kernel.org" <kvm@vger.kernel.org>
Link: https://lkml.kernel.org/r/1561955054-1838-2-git-send-email-mikelley@microsoft.com
|
|
Currently the clocksource and clockevent support for davinci platforms
lives in mach-davinci. It hard-codes many things, uses global variables,
implements functionalities unused by any platform and has code fragments
scattered across many (often unrelated) files.
Implement a new, modern and simplified timer driver and put it into
drivers/clocksource. We still need to support legacy board files so
export a config structure and a function that allows machine code to
register the timer.
The timer we're using is 64-bit but can be programmed in dual 32-bit
mode (both chained and unchained).
On all davinci SoCs except for da830 we're using both halves. Lower half
for clockevents and upper half for clocksource. On da830 we're using the
lower half for both with the help of a compare register.
This patch contains the core code and support for clockevent. The
clocksource code will be included in a subsequent patch.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The system counter (sys_ctr) is a programmable system counter
which provides a shared time base to the Cortex A15, A7, A53 etc cores.
It is intended for use in applications where the counter is always
powered on and supports multiple, unrelated clocks. The sys_ctr hardware
supports:
- 56-bit counter width (roll-over time greater than 40 years)
- compare frame(64-bit compare value) contains programmable interrupt
generation when compare value <= counter value.
[dlezcano] Fixed over 80 chars length warning
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Rename driver's source file to better reflect that it's not specific to
older SoC generations.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull clocksource updates from Ingo Molnar:
"Misc clocksource/clockevent driver updates that came in a bit late but
are ready for v5.2"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
misc: atmel_tclib: Do not probe already used TCBs
clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static
clocksource/drivers/tcb_clksrc: Rename the file for consistency
clocksource/drivers/timer-atmel-pit: Rework Kconfig option
clocksource/drivers/tcb_clksrc: Move Kconfig option
ARM: at91: Implement clocksource selection
clocksource/drivers/tcb_clksrc: Use tcb as sched_clock
clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib
ARM: at91: move SoC specific definitions to SoC folder
clocksource/drivers/timer-milbeaut: Cleanup common register accesses
clocksource/drivers/timer-milbeaut: Add shutdown function
clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer
clocksource/drivers/tegra: Rework for compensation of suspend time
clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804
clocksource/drivers/sun4i: Add a compatible for suniv
dt-bindings: timer: Add Allwinner suniv timer
|
|
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
This adds a new slightly rewritten timer driver for the
Intel IXP4xx clocksource, clockevent and delay timer.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM new SoC family support from Arnd Bergmann:
"Two new SoC families are added this time.
Sugaya Taichi submitted support for the Milbeaut SoC family from
Socionext and explains:
"SC2000 is a SoC of the Milbeaut series. equipped with a DSP
optimized for computer vision. It also features advanced
functionalities such as 360-degree, real-time spherical stitching
with multi cameras, image stabilization for without mechanical
gimbals, and rolling shutter correction. More detail is below:
https://www.socionext.com/en/products/assp/milbeaut/SC2000.html"
Interestingly, this one has a history dating back to older chips made
by Socionext and previously Matsushita/Panasonic based on their own
mn10300 CPU architecture that was removed from the kernel last year.
Manivannan Sadhasivam adds support for another SoC family, this is the
Bitmain BM1880 chip used in the Sophon Edge TPU developer board.
The chip is intended for Deep Learning applications, and comes with
dual-core Arm Cortex-A53 to run Linux as well as a RISC-V
microcontroller core to control the tensor unit. For the moment, the
TPU is not accessible in mainline Linux, so we treat it as a generic
Arm SoC.
More information is available at
https://www.sophon.ai/"
* tag 'armsoc-newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: multi_v7_defconfig: add ARCH_MILBEAUT and ARCH_MILBEAUT_M10V
ARM: configs: Add Milbeaut M10V defconfig
ARM: dts: milbeaut: Add device tree set for the Milbeaut M10V board
clocksource/drivers/timer-milbeaut: Introduce timer for Milbeaut SoCs
dt-bindings: timer: Add Milbeaut M10V timer description
ARM: milbeaut: Add basic support for Milbeaut m10v SoC
dt-bindings: Add documentation for Milbeaut SoCs
dt-bindings: arm: Add SMP enable-method for Milbeaut
dt-bindings: sram: milbeaut: Add binding for Milbeaut smp-sram
MAINTAINERS: Add entry for Bitmain SoC platform
arm64: dts: bitmain: Add Sophon Egde board support
arm64: dts: bitmain: Add BM1880 SoC support
arm64: Add ARCH_BITMAIN platform
dt-bindings: arm: Document Bitmain BM1880 SoC
|
|
Add timer driver for Milbeaut SoCs series.
The timer has two 32-bit width down counters, one of which is configured
as a clockevent device and the other is configured as a clock source.
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Add clock driver for RDA Micro RDA8810PL SoC supporting OSTIMER
and HWTIMER.
RDA8810PL has two independent timers: OSTIMER (56 bit) and HWTIMER
(64 bit). Each timer provides optional interrupt support. In this
driver, OSTIMER is used for clockevents and HWTIMER is used for
clocksource.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In order to unify the names in this directory, let's rename the driver to be
prefixed with timer-*
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In order to unify the names in this directory, let's rename the driver to be
prefixed with timer-*
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In order to unify the names in this directory, let's rename the driver to be
prefixed with timer-*
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In order to unify the names in this directory, let's rename the driver to be
prefixed with timer-*
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In order to unify the names in this directory, let's rename the driver to be
prefixed with timer-*
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more timer updates from Thomas Gleixner:
"A set of commits for the new C-SKY architecture timers"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings: timer: gx6605s SOC timer
clocksource/drivers/c-sky: Add gx6605s SOC system timer
dt-bindings: timer: C-SKY Multi-processor timer
clocksource/drivers/c-sky: Add C-SKY SMP timer
|
|
The driver is for gx6605s SOC system timer and there are two
same timers in gx6605s. We use one for clkevt and another one for
clksrc.
The timer is mmio map to access, so we need give mmio address in dts.
The counter at 0x0 offset is clock event.
The counter at 0x40 offset is clock source.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The driver is for C-SKY SMP timer. It only supports oneshot event
and 32bit overflow for clocksource. Per cpu core has one timer and
all timers share one clock-counter-input from the same clocksource.
This use mfcr&mtcr instructions to access the regs.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In order to make some housekeeping in the directory, this patch renames
drivers to the timer-* format in order to unify their names.
There is no functional changes.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains some major improvements to the RISC-V port, including
the necessary interrupt controller and timer support to actually make
it to userspace. Support for three devices has been added:
- the ISA-mandated timers on RISC-V systems.
- the ISA-mandated first-level interrupt controller on RISC-V
systems, which is handled as part of our core arch code because
it's very small and tightly tied to the ISA.
- SiFive's platform-level interrupt controller, which talks to the
actual devices.
In addition to these new devices, there are a handful of cleanups all
over the RISC-V tree:
- build fixes for various configurations:
* A fix to the vDSO build's makefile so it respects CFLAGS.
* The addition of __lshrti3, a libgcc derived function necessary
for some 32-bit configurations.
* !SMP && PERF_EVENTS
- Cleanups to the arch code to remove the remnants of old versions of
the drivers that were just properly submitted.
* Some dead code from the timer driver, most of which wasn't ever
even compiled.
* Cleanups of some interrupt #defines, which are now local to the
interrupt handling code.
- Fixes to ptrace(), which while not being sufficient to fully make
GDB work are at least sufficient to get simple GDB tasks to work.
- Early printk support via RISC-V's architecturally mandated SBI
console device.
- A fix to our early debug trap handler to ensure it's always
aligned.
These patches have all been through a fairly extensive review process,
but as this enables a whole pile of functionality (ie, userspace) I'm
confident we'll need to submit a few more patches. The only concrete
issues I know about are the sys_riscv_flush_icache patches, but as I
managed to screw those up on Friday I figured it'd be best to let them
bake another week.
This tag boots a Fedora root filesystem on QEMU's master branch for
me, and before this morning's rebase (from 4.18-rc8 to 4.18) it booted
on the HiFive Unleashed.
Thanks to Christoph Hellwig and the other guys at WD for getting the
new drivers in shape!"
* tag 'riscv-for-linus-4.19-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
dt-bindings: interrupt-controller: SiFive Plaform Level Interrupt Controller
dt-bindings: interrupt-controller: RISC-V local interrupt controller
RISC-V: Fix !CONFIG_SMP compilation error
irqchip: add a SiFive PLIC driver
RISC-V: Add the directive for alignment of stvec's value
clocksource: new RISC-V SBI timer driver
RISC-V: implement low-level interrupt handling
RISC-V: add a definition for the SIE SEIE bit
RISC-V: remove INTERRUPT_CAUSE_* defines from asm/irq.h
RISC-V: simplify software interrupt / IPI code
RISC-V: remove timer leftovers
RISC-V: Add early printk support via the SBI console
RISC-V: Don't increment sepc after breakpoint.
RISC-V: implement __lshrti3.
RISC-V: Use KBUILD_CFLAGS instead of KCFLAGS when building the vDSO
|
|
The RISC-V ISA defines a per-hart real-time clock and timer, which is
present on all systems. The clock is accessed via the 'rdtime'
pseudo-instruction (which reads a CSR), and the timer is set via an SBI
call.
Contains various improvements from Atish Patra <atish.patra@wdc.com>.
Signed-off-by: Dmitriy Cherkasov <dmitriy@oss-tech.org>
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
[hch: remove dead code, add SPDX tags, used riscv_of_processor_hart(),
minor cleanups, merged hotplug cpu support and other improvements
from Atish]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Rename mtk_timer to timer-mediatek to apply new naming convention
in clocksource folder.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull missed timer updates from Thomas Gleixner:
"This is a branch which got forgotten during the merge window, but it
contains only fixes and hardware enablement. No fundamental changes.
- Various fixes for the imx-tpm clocksource driver
- A new timer driver for the NCPM7xx SoC family"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/imx-tpm: Add different counter width support
clocksource/drivers/imx-tpm: Correct some registers operation flow
clocksource/drivers/imx-tpm: Fix typo of clock name
dt-bindings: timer: tpm: fix typo of clock name
clocksource/drivers/npcm: Add NPCM7xx timer driver
dt-binding: timer: document NPCM7xx timer DT bindings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
|
|
Add Nuvoton BMC NPCM7xx timer driver.
The clocksource Enable 24-bit TIMER0 and TIMER1 counters,
while TIMER0 serve as clockevent and TIMER1 serve as clocksource.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Brendan Higgins <brendanhiggins@xxxxxxxxxx>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Now that arch/metag/ has been removed, remove the metag generic
per-thread timer driver. It is of no value without the architecture
code.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-metag@vger.kernel.org
|
|
Move the dmtimer driver out of plat-omap to clocksource.
So that non-omap devices also could use this.
No Code changes done to the driver file only renamed to timer-ti-dm.c.
Also removed the config dependencies for OMAP_DM_TIMER.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
[tony@atomide.com: add select omap_dm_timer for omap16xx]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ATCPIT100 is often used on the Andes architecture,
This timer provide 4 PIT channels. Each PIT channel is a
multi-function timer, can be configured as 32,16,8 bit timers
or PWM as well.
For system timer it will set channel 1 32-bit timer0 as clock
source and count downwards until underflow and restart again.
It also set channel 0 32-bit timer0 as clock event and count
downwards until condition match. It will generate an interrupt
for handling periodically.
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add andestech atcpit100 timer
|
|
platform
The Spreadtrum SC9860 platform will use the architected timers as local
clock events, but we also need a broadcast timer device to wake up the
CPUs when the CPUs are in sleep mode.
The Spreadtrum timer can support 32-bit or 64-bit counters, as well as
supporting period mode or one-shot mode.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-8-git-send-email-daniel.lezcano@linaro.org
[ Minor readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
IMX Timer/PWM Module (TPM) supports both timer and pwm function while
this patch only adds the timer support. PWM would be added later.
The TPM counter, compare and capture registers are clocked by an
asynchronous clock that can remain enabled in low power modes.
NOTE: We observed in a very small probability, the bus fabric
contention between GPU and A7 may results a few cycles delay
of writing CNT registers which may cause the min_delta event got
missed, so we need add a ETIME check here in case it happened.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"New SoC specific drivers:
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini
SoCs
- Various subsystem-wide cleanups
Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA data
path acceleration that has previously been used on PowerPC chips. I
ended up postponing the merge until some API questions for its unusual
MMIO access are resolved"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
clocksource: owl: Add S900 support
clocksource: Add Owl timer
soc: renesas: rcar-sysc: Use GENPD_FLAG_ALWAYS_ON
firmware: tegra: Fix locking bugs in BPMP
soc/tegra: flowctrl: Fix error handling
soc/tegra: bpmp: Implement generic PM domains
soc/tegra: bpmp: Update ABI header
PM / Domains: Allow overriding the ->xlate() callback
soc: brcmstb: enable drivers for ARM64 and BMIPS
soc: renesas: Rework Kconfig and Makefile logic
reset: Add the TI SCI reset driver
dt-bindings: reset: Add TI SCI reset binding
reset: use kref for reference counting
soc: qcom: smsm: Improve error handling, quiesce probe deferral
cpufreq: scpi: use new scpi_ops functions to remove duplicate code
firmware: arm_scpi: add support to populate OPPs and get transition latency
dt-bindings: reset: Add reset manager offsets for Stratix10
memory: omap-gpmc: add error message if bank-width property is absent
memory: omap-gpmc: make dts snippet include semicolon
reset: Add a Gemini reset controller
...
|
|
The Actions Semi S500 SoC provides four timers, 2Hz0/1 and 32-bit TIMER0/1.
Use TIMER0 as clocksource and TIMER1 as clockevents.
Based on LeMaker linux-actions tree.
An S500 datasheet can be found on the LeMaker Guitar pages:
http://www.lemaker.org/product-guitar-download-29.html
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
The different drivers are all using the same pattern when initializing.
1. Get the base address
2. Get the irq number
3. Get the clock
4. Prepare and enable the clock
5. Get the rate
6. Request an interrupt
Instead of repeating again and again these steps in all the drivers, let's
provide a common init routine to give the opportunity to factor all of them
out.
We can expect a significant kernel size improvement when the common routine
will be used in all the drivers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The config option name is now renamed to 'TIMER_OF' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
After discussing it, this feature is dropped as it is not considered
adequate:
https://patchwork.kernel.org/patch/9639317/
There is no user of this macro yet, so there is no impact on the drivers.
This reverts commit 376bc27150f180d9f5eddec6a14117780177589d.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
This merges the Moxa Art timer driver into the Faraday FTTMR010
driver and replaces all Kconfig symbols to use the Faraday
driver instead. We are now so similar that the drivers can
be merged by just adding a few lines to the Faraday timer.
Differences:
- The Faraday driver explicitly sets the counter to count
upwards for the clocksource, removing the need for the
clocksource core to invert the value.
- The Faraday driver also handles sched_clock()
On the Aspeed, the counter can only count downwards, so support
the timers in downward-counting mode as well, and flag the
Aspeed to use this mode. This mode was tested on the Gemini so
I have high hopes that it'll work fine on the Aspeed as well.
After this we have one driver for all three SoCs and a generic
Faraday FTTMR010 timer driver, which is nice.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
After some research it turns out that the "Gemini" timer is
actually a generic IP block from Faraday Technology named
FTTMR010, so as to not make things too confusing we need to
rename the driver and its symbols to make sense.
The implementation remains the same in this patch but we fix
the copy-paste error in the timer name "nomadik_mtu" as we're
at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
This patch adds a OSTM driver for the Renesas architecture.
The OS Timer (OSTM) has independent channels that can be
used as a freerun or interval times.
This driver uses the first probed device as a clocksource
and then any additional devices as clock events.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
This is a rewrite of the Gemini timer
driver in arch/arm/mach-gemini/timer.c trying to do everything
the device tree way:
- Make every IO-access relative to a base address and dynamic
so we can do a dynamic ioremap and get going.
- Do not poke around directly in the global syscon registers,
access them using the syscon regmap style design pattern for
the one register we need to check.
- Find register range and interrupt from the device tree.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The current code uses the CLOCKSOURCE_OF_DECLARE macro to fill the clksrc
table with a t-uple (name, init_function).
Unfortunately it ends up to the clockevent and the clocksource being
both initialized with this macro. It is not a problem by itself but there
is not a clear distinction between a clockevent and a clocksource in the
code initialization path. Somebody can argue there are the same IP block
and the same DT node. But conceptually from the software side, there are
two distincts entities and as is they should be initialized separetely.
Some drivers which do not have a clocksource end up by using the
CLOCKSOURCE_OF_DECLARE macro to declare a clockevent.
Another result is the fuzzy organization in the clocksource directory,
where the clockevents are implemented in the same file than the
clocksources or file labelled timer-something implementing a clocksource.
This patch provides another macro to specifically declare a clockevent in
the same way than the clocksource and gives the opportunity to write two
separate drivers, one for the clocksource and another for the clockevents.
Hopefully, that can help to do some housework in the directory, perhaps
split the drivers in to entities, for example:
- clksrc-rockchip.c
- clkevt-rockchip.c
Also, it gives the possibility to declare clocksources separately in the
DT and then use a clocksource from IP block while while clockevents are
used from another IP block.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
This adds support for
- CONFIG_ARC_TIMERS : legacy 32-bit TIMER0 and TIMER1 which count UP
from @CNT to @LIMIT, before optionally triggering an interrupt.
These are programmed using ARC auxiliary register interface.
These are present in all ARC cores (ARC700 and ARC HS38)
TIMER0 serves as clockevent for all ARC linux builds.
TIMER1 is used for clocksource in arc700 builds.
- CONFIG_ARC_TIMERS_64BIT: 64-bit counters, RTC and GFRC found in
ARC HS38 cores. These are independnet IP blocks with different
programming model respectively.
Link: http://lkml.kernel.org/r/20161111231132.GA4186@mai
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
