| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
message
Prevent creating clk alias for non existing gmac_gmii_ref_clk_div clock and,
this way, eliminate excessive error message during boot:
"ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_clk_div"
Fixes: c097338ebd3f ("ARM: dts: dra7: cpsw: fix clocks tree")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The OMAP36xx DPLL5, driving EHCI USB, can be subject to a long-term
frequency drift. The frequency drift magnitude depends on the VCO update
rate, which is inversely proportional to the PLL divider. The kernel
DPLL configuration code results in a high value for the divider, leading
to a long term drift high enough to cause USB transmission errors. In
the worst case the USB PHY's ULPI interface can stop responding,
breaking USB operation completely. This manifests itself on the
Beagleboard xM by the LAN9514 reporting 'Cannot enable port 2. Maybe the
cable is bad?' in the kernel log.
Errata sprz319 advisory 2.1 documents PLL values that minimize the
drift. Use them automatically when DPLL5 is used for USB operation,
which we detect based on the requested clock rate. The clock framework
will still compute the PLL parameters and resulting rate as usual, but
the PLL M and N values will then be overridden. This can result in the
effective clock rate being slightly different than the rate cached by
the clock framework, but won't cause any adverse effect to USB
operation.
Signed-off-by: Richard Watts <rrw@kynesim.co.uk>
[Upported from v3.2 to v4.9]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The Kconfig currently controlling compilation of this code is:
arch/arm/mach-omap2/Kconfig:config SOC_DRA7XX
arch/arm/mach-omap2/Kconfig: bool "TI DRA7XX"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tags etc. since all that information
is already contained at the top of the file in the comments.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
|
|
Add clk node for RNG module.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add tblck to the pwm nodes. This insures that the ehrpwm driver has access
to the time-based clk.
Do not remove similar entries for ehrpwm node. Later patches will switch
from using ehrpwm node name to pwm. But to maintain ABI compatibility we
shouldn't remove the old entries.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"It's the usual big pile of driver updates and additions, but we do
have a couple core changes in here as well.
Core:
- CLK_IS_CRITICAL support has been added. This should allow drivers
to properly express that a certain clk should stay on even if their
prepare/enable count drops to 0 (and in turn the parents of these
clks should stay enabled).
- A clk registration API has been added, clk_hw_register(), and an OF
clk provider API has been added, of_clk_add_hw_provider(). These
APIs have been put in place to further split clk providers from clk
consumers, with the goal being to have clk providers never deal
with struct clk pointers at all. Conversion of provider drivers is
on going. clkdev has also gained support for registering clk_hw
pointers directly so we can convert drivers that don't use
devicetree.
New Drivers:
- Marvell ap806 and cp110 system controllers (with clks inside!)
- Hisilicon Hi3519 clock and reset controller
- Axis ARTPEC-6 clock controllers
- Oxford Semiconductor OXNAS clock controllers
- AXS10X I2S PLL
- Rockchip RK3399 clock and reset controller
Updates:
- MMC2 and UART2 clks on Samsung Exynos 3250, ACLK on Samsung Exynos
542x SoCs, and some more clk ID exporting for bus frequency scaling
- Proper BCM2835 PCM clk support and various other clks
- i.MX clk updates for i.MX6SX, i.MX7, and VF610
- Renesas updates for R-Car H3
- Tegra210 got updates for DisplayPort and HDMI 2.0
- Rockchip driver refactorings and fixes due to adding RK3399 support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (139 commits)
clk: fix critical clock locking
clk: qcom: mmcc-8996: Remove clocks that should be controlled by RPM
clk: ingenic: Allow divider value to be divided
clk: sunxi: Add display and TCON0 clocks driver
clk: rockchip: drop old_rate calculation on pll rate changes
clk: rockchip: simplify GRF handling in pll clocks
clk: rockchip: lookup General Register Files in rockchip_clk_init
clk: rockchip: fix the rk3399 sdmmc sample / drv name
clk: mvebu: new driver for Armada CP110 system controller
dt-bindings: arm: add DT binding for Marvell CP110 system controller
clk: mvebu: new driver for Armada AP806 system controller
clk: hisilicon: add CRG driver for hi3519 soc
clk: hisilicon: export some hisilicon APIs to modules
reset: hisilicon: add reset controller driver for hisilicon SOCs
clk: bcm/kona: Do not use sizeof on pointer type
clk: qcom: msm8916: Fix crypto clock flags
clk: nxp: lpc18xx: Initialize clk_init_data::flags to 0
clk/axs10x: Add I2S PLL clock driver
clk: imx7d: fix ahb clock mux 1
clk: fix comment of devm_clk_hw_register()
...
|
|
of_find_node_by_name() will call of_node_put() on the node so we need to
get it first to avoid warnings.
The cfg_node needs to be put after we have finished processing the
properties.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The OMAP Platform code provides possibility to select GP Timer as
default clocksource instead of counter_32K by using bootcmd parameter
'clocksource', but the system will crash during early boot when this
option is used on dra7 or omap5 platforms, because it will hit BUG()
statement:
omap2_gptimer_clocksource_init
->BUG_ON(res);
This happens because clk_dev alias "sys_clkin_ck" is not registered.
Hence, fix it by adding missing "sys_clkin_ck" clk_dev aliases
definitions for omap5 and dra7.
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
AM33xx/AM43xx devices use the same DPLL IP blocks, which only support
maximum rate of 1GHz [1] for the default and 2GHz for the low-jitter type
DPLLs [2]. Reflect this limitation in the DPLL init code by adding the
max-rate parameter based on the DPLL types.
[1] Functional, integration & test specification for GS70 ADPLLS, Rev 1.0-01
[2] Functional, integration & test specification for GS70 ADPLLLJ, Rev 0.8-02
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
DPLLs typically have a maximum rate they can support, and this varies
from DPLL to DPLL. Add support of the maximum rate value to the DPLL
data struct, and also add check for this in the DPLL round_rate function.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Commit 7aba4f5201d1 ("clk: ti: dflt: fix enable_reg validity check")
fixed a validation check by using an IS_ERR() macro within the
existing unlikely expression, but IS_ERR() macro already has an
unlikely inside it, so get rid of the redundant unlikely macro
from the validation check.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
rename the mcasp8_ahclk_mux to mcasp8_ahclkx_mux.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for the unit offsets]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This flag is a no-op now. Remove usage of the flag.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Conflicts:
drivers/clk/Kconfig
|
|
drivers/clk/ti/clk-814x.c:34:12: warning: symbol 'dm814x_adpll_early_init' was not declared. Should it be static?
drivers/clk/ti/clk-814x.c:58:12: warning: symbol 'dm814x_adpll_enable_init_clocks' was not declared. Should it be static?
drivers/clk/ti/adpll.c:465 ti_adpll_recalc_rate() warn: should '__readw(d->regs + 20) << 18' be a 64 bit type?
drivers/clk/ti/adpll.c:945 ti_adpll_probe() error: we previously assumed 'd->clocks' could be null (see line 921)
The last one looks like a real bug because we don't return an
error on allocation failure.
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The arch independent drivers can be build testeed with
COMPILE_TEST. Let's allow that for drivers/clk/ti.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
On dm814x we have 13 ADPLLs with 3 to 4 outputs on each. The
ADPLLs have several dividers and muxes controlled by a shared
control register for each PLL.
Note that for the clocks to work as device drivers for booting on
dm814x, this patch depends on "ARM: OMAP2+: Change core_initcall
levels to postcore_initcall" that has already been merged.
Also note that this patch does not implement clk_set_rate for the
PLL, that will be posted later on when available.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
Change the types here to unsigned int instead of int and update
the checks for == 0 instead < 1 to be more explicit about what's
going on now that of_clk_get_parent_count() has changed return
types.
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Convert DPLL support code to use clk_hw pointers for reference and bypass
clocks. This allows us to use clk_hw_* APIs for accessing any required
parameters for these clocks, avoiding some locking problems at least with
DPLL enable code; this used clk_get_rate which uses mutex but isn't
good under clk_enable / clk_disable.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
* clk-fixes:
clk: ti: omap3+: dpll: use non-locking version of clk_get_rate
|
|
As the code in this file is being executed within irq context in some
cases, we must avoid the clk_get_rate which uses mutex internally.
Switch the code to use clk_hw_get_rate instead which is non-locking.
This fixes an issue where PM runtime will hang the system if enabled
with a serial console before a suspend-resume cycle.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: a53ad8ef3dcc ("clk: ti: Convert to clk_hw based provider APIs")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
to_clk_*(_hw) macros have been repeatedly defined in many places.
This patch moves all the to_clk_*(_hw) definitions in the common
clock framework to public header clk-provider.h, and drop the local
definitions.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-urgent ARM SoC fixes from Olof Johansson:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform
so these can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: Fix randconfig build warning for dm814_pllss_data
ARM: sa1100/simpad: Be sure to clamp return value
ARM: scoop: Be sure to clamp return value
ARM: davinci: fix a problematic usage of WARN()
ARM: davinci: only select WT cache if cache is enabled
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
MAINTAINERS: gpio-brcmstb: Remove stray '>'
MAINTAINERS: brcmstb: Include Broadcom internal mailing-list
|
|
The timer clock aliases are needed early on dm814x. Let's also
add the aliases for the interconnects and MMC.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
* clk-fixes:
clk: sunxi: pll2: Fix clock running too fast
clk: scpi: add missing of_node_put
clk: qoriq: fix memory leak
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
clk: mmp: add linux/clk.h includes
clk: ti: drop locking code from mux/divider drivers
clk: ti816x: Add missing dmtimer clkdev entries
clk: ti: fapll: fix wrong do_div() usage
clk: ti: clkt_dpll: fix wrong do_div() usage
clk: gpio: Get parent clk names in of_gpio_clk_setup()
|
|
Errata i810 states that DPLL controller can get stuck while transitioning
to a power saving state, while its M/N ratio is being re-programmed.
As a workaround, before re-programming the M/N ratio, SW has to ensure
the DPLL cannot start an idle state transition. SW can disable DPLL
idling by setting the DPLL AUTO_DPLL_MODE=0 or keeping a clock request
active by setting a dependent clock domain in SW_WKUP.
This errata impacts OMAP5 and DRA7 chips, so enable the errata for these.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
TI's mux and divider clock drivers do not require locking and they do
not initialize internal spinlocks. This code was occasionally
copy-posted from generic mux/divider drivers. So remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add missing clkdev dmtimer related entries for dm816x.
32Khz and ext sources were missing.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
The clk_hw_omap_ops structures are never modified, so declare this one as
const, like the others.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The default clock enabling functions for TI clocks -
omap2_dflt_clk_enable() and omap2_dflt_clk_disable() perform a
NULL check for the enable_reg field of the clk_hw_omap structure.
This enable_reg field however is merely a combination of the index
of the master IP module, and the offset from the master IP module's
base address. A value of 0 is perfectly valid, and the current error
checking will fail in these cases. The issue was found when trying
to enable the iva2_ck clock on OMAP3 platforms.
So, switch the check to use IS_ERR. This correction is similar to the
logic used in commit c807dbedb5e5 ("clk: ti: fix ti_clk_get_reg_addr
error handling").
Fixes: 9f37e90efaf0 ("clk: ti: dflt: move support for default gate clock..")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
On the OMAP AM3517 platform the uart4_ick gets registered
twice, causing any power management to /dev/ttyO3 to fail
when trying to wake the device up.
This solves the following oops:
[] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa09e008
[] PC is at serial_omap_pm+0x48/0x15c
[] LR is at _raw_spin_unlock_irqrestore+0x30/0x5c
Fixes: aafd900cab87 ("CLK: TI: add omap3 clock init file")
Cc: stable@vger.kernel.org
Cc: mturquette@baylibre.com
Cc: sboyd@codeaurora.org
Cc: linux-clk@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@lists.codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
The ABE related clocks should be configured via DT and not have it wired
inside of the kernel.
Fixes: a74c52def9ab ("clk: ti: clk-7xx: Correct ABE DPLL configuration")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
|
|
Use the provider based method to get a clock's name so that we
can get rid of the clk member in struct clk_hw one day. Mostly
converted with the following coccinelle script.
@@
struct clk_hw *E;
@@
-__clk_get_name(E->clk)
+clk_hw_get_name(E)
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kevin Cernekee <cernekee@chromium.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This code is never called with a basic clock type, so the check
here is not doing anything useful and is blocking the removal of
__clk_get_flags(). Remove the check so we can delete the
__clk_get_flags() API.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Mostly converted with the following snippet:
@@
struct clk_hw *E;
@@
-__clk_get_flags(E->clk)
+clk_hw_get_flags(E)
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Mostly converted with the following semantic patch:
@@
struct clk_hw *E;
@@
-__clk_get_num_parents(E->clk)
+clk_hw_get_num_parents(E)
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chao Xie <chao.xie@marvell.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: "Emilio López" <emilio@elopez.com.ar>
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The patch adds the missing dpll_clksel_mac_clk clock node.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
* cleanup-clk-h-includes: (62 commits)
clk: Remove clk.h from clk-provider.h
clk: h8300: Remove clk.h and clkdev.h includes
clk: at91: Include clk.h and slab.h
clk: ti: Switch clk-provider.h include to clk.h
clk: pistachio: Include clk.h
clk: ingenic: Include clk.h
clk: si570: Include clk.h
clk: moxart: Include clk.h
clk: cdce925: Include clk.h
clk: Include clk.h in clk.c
clk: zynq: Include clk.h
clk: ti: Include clk.h
clk: sunxi: Include clk.h and remove unused clkdev.h includes
clk: st: Include clk.h
clk: qcom: Include clk.h
clk: highbank: Include clk.h
clk: bcm: Include clk.h
clk: versatile: Remove clk.h and clkdev.h includes
clk: ux500: Remove clk.h and clkdev.h includes
clk: tegra: Properly include clk.h
...
|
|
Use of_clk_parent_fill to fill in the parent clock names' array.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add __force here so that sparse doesn't complain about us playing
tricks with __iomem.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Sparse complains about these structures missing static, but they
also don't look to be used. Remove them.
drivers/clk/ti/clk-3xxx.c:74:30: warning: symbol 'clkhwops_omap3430es2_ssi_wait' was not declared. Should it be static?
drivers/clk/ti/clk-3xxx.c:157:30: warning: symbol 'clkhwops_omap3430es2_hsotgusb_wait' was not declared. Should it be static?
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This variable isn't exported outside of this file so mark it
static. Silences the following sparse warning:
drivers/clk/ti/clk.c:36:24: warning: symbol 'ti_clk_features' was not declared. Should it be static?
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
smatch reports a failure to check kzalloc() here:
drivers/clk/ti/clk.c:232
omap2_clk_provider_init() error: potential null dereference 'io'.
(kzalloc returns null)
Check for an allocation failure and return -ENOMEM.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
