summaryrefslogtreecommitdiffstats
path: root/drivers/char
AgeCommit message (Collapse)AuthorFilesLines
2015-05-05ipmi: Fix multi-part message handlingCorey Minyard1-13/+38
Lots of little fixes for multi-part messages: The values was not being re-initialized, if something went wrong handling a multi-part message and it got left in a bad state, it might be an issue. The commands were not correct when issuing multi-part reads, the code was not passing in the proper value for commands. Also clean up some minor formatting issues. Get the block number from the right location, limit the maximum send message size to 63 bytes and explain why, and fix some minor sylistic issues. Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05ipmi: Add alert handling to SSIFCorey Minyard1-16/+116
The SSIF interface can optionally have an SMBus alert come in when data is ready. Unfortunately, the IPMI spec gives wiggle room to the implementer to allow them to always have the alert enabled, even if the driver doesn't enable it. So implement alerts. If you don't in this situation, the SMBus alert handling will constantly complain. Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05ipmi: Fix a problem that messages are not issued in run_to_completion modeHidehiro Kawai1-2/+1
start_next_msg() issues a message placed in smi_info->waiting_msg if it is non-NULL. However, sender() sets a message to smi_info->curr_msg and NULL to smi_info->waiting_msg in the context of run_to_completion mode. As the result, it leads an infinite loop by waiting the completion of unissued message when leaving dying message after kernel panic. sender() should set the message to smi_info->waiting_msg not curr_msg. Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com> Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05ipmi: Report an error if ACPI _IFT doesn't existCorey Minyard1-1/+3
When probing an ACPI table, report a specific error, instead of just returning an error, if _IFT doesn't exist. Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05ipmi: Remove unused including <linux/version.h>Wei Yongjun1-1/+0
Remove including <linux/version.h> that don't need it. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05ipmi: Don't report err in the SI driver for SSIF devicesCorey Minyard1-2/+3
Really ignore them by returning -ENODEV from the probe, but not doing anything. Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05ipmi: Remove incorrect use of seq_has_overflowedJoe Perches3-5/+5
commit d6c5dc18d863 ("ipmi: Remove uses of return value of seq_printf") incorrectly changed the return value of various proc_show functions to use seq_has_overflowed(). These functions should return 0 on completion rather than 1/true on overflow. 1 is the same as #define SEQ_SKIP which would cause the output to not be emitted (skipped) instead. This is a logical defect only as the length of these outputs are all smaller than the initial allocation done by the seq filesystem. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05ipmi:ssif: Ignore spaces when comparing I2C adapter namesCorey Minyard1-3/+22
Some of the adapters have spaces in their names, but that's really hard to pass in as a module or kernel parameters. So ignore the spaces. Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05ipmi_ssif: Fix the logic on user-supplied addressesCorey Minyard1-1/+1
Returning zero is success. Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds1-9/+9
Pull crypto fixes from Herbert Xu: "This fixes a build problem with bcm63xx and yet another fix to the memzero_explicit function to ensure that the memset is not elided" * git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: hwrng: bcm63xx - Fix driver compilation lib: make memzero_explicit more robust against dead store elimination
2015-05-04hwrng: bcm63xx - Fix driver compilationÁlvaro Fernández Rojas1-9/+9
- s/clk_didsable_unprepare/clk_disable_unprepare - s/prov/priv - s/error/ret (bcm63xx_rng_probe) Fixes: 6229c16060fe ("hwrng: bcm63xx - make use of devm_hwrng_register") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2015-04-21Merge tag 'char-misc-4.1-rc1' of ↵Linus Torvalds10-43/+43
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here's the big char/misc driver patchset for 4.1-rc1. Lots of different driver subsystem updates here, nothing major, full details are in the shortlog. All of this has been in linux-next for a while" * tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits) mei: trace: remove unused TRACE_SYSTEM_STRING DTS: ARM: OMAP3-N900: Add lis3lv02d support Documentation: DT: lis302: update wakeup binding lis3lv02d: DT: add wakeup unit 2 and wakeup threshold lis3lv02d: DT: use s32 to support negative values Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case mei: replace check for connection instead of transitioning mei: use mei_cl_is_connected consistently mei: fix mei_poll operation hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg() Drivers: hv: hv_balloon: survive ballooning request with num_pages=0 Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function Drivers: hv: hv_balloon: do not online pages in offline blocks hv: remove the per-channel workqueue hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind() hv: run non-blocking message handlers in the dispatch tasklet coresight: moving to new "hwtracing" directory coresight-tmc: Adding a status interface to sysfs coresight: remove the unnecessary configuration coresight-default-sink ...
2015-04-16Merge tag 'stable/for-linus-4.1-rc0-tag' of ↵Linus Torvalds1-2/+3
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen features and fixes from David Vrabel: - use a single source list of hypercalls, generating other tables etc. at build time. - add a "Xen PV" APIC driver to support >255 VCPUs in PV guests. - significant performance improve to guest save/restore/migration. - scsiback/front save/restore support. - infrastructure for multi-page xenbus rings. - misc fixes. * tag 'stable/for-linus-4.1-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/pci: Try harder to get PXM information for Xen xenbus_client: Extend interface to support multi-page ring xen-pciback: also support disabling of bus-mastering and memory-write-invalidate xen: support suspend/resume in pvscsi frontend xen: scsiback: add LUN of restored domain xen-scsiback: define a pr_fmt macro with xen-pvscsi xen/mce: fix up xen_late_init_mcelog() error handling xen/privcmd: improve performance of MMAPBATCH_V2 xen: unify foreign GFN map/unmap for auto-xlated physmap guests x86/xen/apic: WARN with details. x86/xen: Provide a "Xen PV" APIC driver to support >255 VCPUs xen/pciback: Don't print scary messages when unsupported by hypervisor. xen: use generated hypercall symbols in arch/x86/xen/xen-head.S xen: use generated hypervisor symbols in arch/x86/xen/trace.c xen: synchronize include/xen/interface/xen.h with xen xen: build infrastructure for generating hypercall depending symbols xen: balloon: Use static attribute groups for sysfs entries xen: pcpu: Use static attribute groups for sysfs entry
2015-04-15Merge branch 'for-linus-2' of ↵Linus Torvalds2-13/+9
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull second vfs update from Al Viro: "Now that net-next went in... Here's the next big chunk - killing ->aio_read() and ->aio_write(). There'll be one more pile today (direct_IO changes and generic_write_checks() cleanups/fixes), but I'd prefer to keep that one separate" * 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits) ->aio_read and ->aio_write removed pcm: another weird API abuse infinibad: weird APIs switched to ->write_iter() kill do_sync_read/do_sync_write fuse: use iov_iter_get_pages() for non-splice path fuse: switch to ->read_iter/->write_iter switch drivers/char/mem.c to ->read_iter/->write_iter make new_sync_{read,write}() static coredump: accept any write method switch /dev/loop to vfs_iter_write() serial2002: switch to __vfs_read/__vfs_write ashmem: use __vfs_read() export __vfs_read() autofs: switch to __vfs_write() new helper: __vfs_write() switch hugetlbfs to ->read_iter() coda: switch to ->read_iter/->write_iter ncpfs: switch to ->read_iter/->write_iter net/9p: remove (now-)unused helpers p9_client_attach(): set fid->uid correctly ...
2015-04-15Merge branch 'next' of ↵Linus Torvalds11-975/+1510
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security Pull security subsystem updates from James Morris: "Highlights for this window: - improved AVC hashing for SELinux by John Brooks and Stephen Smalley - addition of an unconfined label to Smack - Smack documentation update - TPM driver updates" * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (28 commits) lsm: copy comm before calling audit_log to avoid race in string printing tomoyo: Do not generate empty policy files tomoyo: Use if_changed when generating builtin-policy.h tomoyo: Use bin2c to generate builtin-policy.h selinux: increase avtab max buckets selinux: Use a better hash function for avtab selinux: convert avtab hash table to flex_array selinux: reconcile security_netlbl_secattr_to_sid() and mls_import_netlbl_cat() selinux: remove unnecessary pointer reassignment Smack: Updates for Smack documentation tpm/st33zp24/spi: Add missing device table for spi phy. tpm/st33zp24: Add proper wait for ordinal duration in case of irq mode smack: Fix gcc warning from unused smack_syslog_lock mutex in smackfs.c Smack: Allow an unconfined label in bringup mode Smack: getting the Smack security context of keys Smack: Assign smack_known_web as default smk_in label for kernel thread's socket tpm/tpm_infineon: Use struct dev_pm_ops for power management MAINTAINERS: Add Jason as designated reviewer for TPM tpm: Update KConfig text to include TPM2.0 FIFO chips tpm/st33zp24/dts/st33zp24-spi: Add dts documentation for st33zp24 spi phy ...
2015-04-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds11-115/+367
Pull crypto update from Herbert Xu: "Here is the crypto update for 4.1: New interfaces: - user-space interface for AEAD - user-space interface for RNG (i.e., pseudo RNG) New hashes: - ARMv8 SHA1/256 - ARMv8 AES - ARMv8 GHASH - ARM assembler and NEON SHA256 - MIPS OCTEON SHA1/256/512 - MIPS img-hash SHA1/256 and MD5 - Power 8 VMX AES/CBC/CTR/GHASH - PPC assembler AES, SHA1/256 and MD5 - Broadcom IPROC RNG driver Cleanups/fixes: - prevent internal helper algos from being exposed to user-space - merge common code from assembly/C SHA implementations - misc fixes" * git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (169 commits) crypto: arm - workaround for building with old binutils crypto: arm/sha256 - avoid sha256 code on ARMv7-M crypto: x86/sha512_ssse3 - move SHA-384/512 SSSE3 implementation to base layer crypto: x86/sha256_ssse3 - move SHA-224/256 SSSE3 implementation to base layer crypto: x86/sha1_ssse3 - move SHA-1 SSSE3 implementation to base layer crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer crypto: arm/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer crypto: arm/sha1-ce - move SHA-1 ARMv8 implementation to base layer crypto: arm/sha1_neon - move SHA-1 NEON implementation to base layer crypto: arm/sha1 - move SHA-1 ARM asm implementation to base layer crypto: sha512-generic - move to generic glue implementation crypto: sha256-generic - move to generic glue implementation crypto: sha1-generic - move to generic glue implementation crypto: sha512 - implement base layer for SHA-512 crypto: sha256 - implement base layer for SHA-256 crypto: sha1 - implement base layer for SHA-1 crypto: api - remove instance when test failed crypto: api - Move alg ref count init to crypto_check_alg ...
2015-04-15xenbus_client: Extend interface to support multi-page ringWei Liu1-2/+3
Originally Xen PV drivers only use single-page ring to pass along information. This might limit the throughput between frontend and backend. The patch extends Xenbus driver to support multi-page ring, which in general should improve throughput if ring is the bottleneck. Changes to various frontend / backend to adapt to the new interface are also included. Affected Xen drivers: * blkfront/back * netfront/back * pcifront/back * scsifront/back * vtpmfront The interface is documented, as before, in xenbus_client.c. Signed-off-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Signed-off-by: Bob Liu <bob.liu@oracle.com> Cc: Konrad Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
2015-04-14Merge tag 'pm+acpi-4.1-rc1' of ↵Linus Torvalds1-12/+1
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management and ACPI updates from Rafael Wysocki: "These are mostly fixes and cleanups all over, although there are a few items that sort of fall into the new feature category. First off, we have new callbacks for PM domains that should help us to handle some issues related to device initialization in a better way. There also is some consolidation in the unified device properties API area allowing us to use that inferface for accessing data coming from platform initialization code in addition to firmware-provided data. We have some new device/CPU IDs in a few drivers, support for new chips and a new cpufreq driver too. Specifics: - Generic PM domains support update including new PM domain callbacks to handle device initialization better (Russell King, Rafael J Wysocki, Kevin Hilman) - Unified device properties API update including a new mechanism for accessing data provided by platform initialization code (Rafael J Wysocki, Adrian Hunter) - ARM cpuidle update including ARM32/ARM64 handling consolidation (Daniel Lezcano) - intel_idle update including support for the Silvermont Core in the Baytrail SOC and for the Airmont Core in the Cherrytrail and Braswell SOCs (Len Brown, Mathias Krause) - New cpufreq driver for Hisilicon ACPU (Leo Yan) - intel_pstate update including support for the Knights Landing chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi) - QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann) - powernv cpufreq driver update (Shilpasri G Bhat) - devfreq update including Tegra support changes (Tomeu Vizoso, MyungJoo Ham, Chanwoo Choi) - powercap RAPL (Running-Average Power Limit) driver update including support for Intel Broadwell server chips (Jacob Pan, Mathias Krause) - ACPI device enumeration update related to the handling of the special PRP0001 device ID allowing DT-style 'compatible' property to be used for ACPI device identification (Rafael J Wysocki) - ACPI EC driver update including limited _DEP support (Lan Tianyu, Lv Zheng) - ACPI backlight driver update including a new mechanism to allow native backlight handling to be forced on non-Windows 8 systems and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede) - New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu) - Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger, Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki) - Fixes related to suspend-to-idle for the iTCO watchdog driver and the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu) - PM tracing support for the suspend phase of system suspend/resume transitions (Zhonghui Fu) - Configurable delay for the system suspend/resume testing facility (Brian Norris) - PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)" * tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits) ACPI / scan: Fix NULL pointer dereference in acpi_companion_match() ACPI / scan: Rework modalias creation when "compatible" is present intel_idle: mark cpu id array as __initconst powercap / RAPL: mark rapl_ids array as __initconst powercap / RAPL: add ID for Broadwell server intel_pstate: Knights Landing support intel_pstate: remove MSR test cpufreq: fix qoriq uniprocessor build ACPI / scan: Take the PRP0001 position in the list of IDs into account ACPI / scan: Simplify acpi_match_device() ACPI / scan: Generalize of_compatible matching device property: Introduce firmware node type for platform data device property: Make it possible to use secondary firmware nodes PM / watchdog: iTCO: stop watchdog during system suspend cpufreq: hisilicon: add acpu driver ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler cpufreq: powernv: Report cpu frequency throttling intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs intel_idle: Update support for Silvermont Core in Baytrail SOC PM / devfreq: tegra: Register governor on module init ...
2015-04-14Merge branch 'for-linus-1' of ↵Linus Torvalds2-2/+1
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull vfs update from Al Viro: "Part one: - struct filename-related cleanups - saner iov_iter_init() replacements (and switching the syscalls to use of those) - ntfs switch to ->write_iter() (Anton) - aio cleanups and splitting iocb into common and async parts (Christoph) - assorted fixes (me, bfields, Andrew Elble) There's a lot more, including the completion of switchover to ->{read,write}_iter(), d_inode/d_backing_inode annotations, f_flags race fixes, etc, but that goes after #for-davem merge. David has pulled it, and once it's in I'll send the next vfs pull request" * 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (35 commits) sg_start_req(): use import_iovec() sg_start_req(): make sure that there's not too many elements in iovec blk_rq_map_user(): use import_single_range() sg_io(): use import_iovec() process_vm_access: switch to {compat_,}import_iovec() switch keyctl_instantiate_key_common() to iov_iter switch {compat_,}do_readv_writev() to {compat_,}import_iovec() aio_setup_vectored_rw(): switch to {compat_,}import_iovec() vmsplice_to_user(): switch to import_iovec() kill aio_setup_single_vector() aio: simplify arguments of aio_setup_..._rw() aio: lift iov_iter_init() into aio_setup_..._rw() lift iov_iter into {compat_,}do_readv_writev() NFS: fix BUG() crash in notify_change() with patch to chown_common() dcache: return -ESTALE not -EBUSY on distributed fs race NTFS: Version 2.1.32 - Update file write from aio_write to write_iter. VFS: Add iov_iter_fault_in_multipages_readable() drop bogus check in file_open_root() switch security_inode_getattr() to struct path * constify tomoyo_realpath_from_path() ...
2015-04-13Merge branch 'pnp'Rafael J. Wysocki1-12/+1
* pnp: PNP: Avoid leaving unregistered device objects in lists PNP: Convert pnp_lock into a mutex PNP: tty/serial/8250/8250_fintek: Use module_pnp_driver to register driver PNP: platform/x86/apple-gmux: Use module_pnp_driver to register driver PNP: net/sb1000: Use module_pnp_driver to register driver PNP: media/rc: Use module_pnp_driver to register driver PNP: ide/ide-pnp: Use module_pnp_driver to register driver PNP: ata/pata_isapnp: Use module_pnp_driver to register driver PNP: tpm/tpm_infineon: Use module_pnp_driver to register driver PNP: Add helper macro for pnp_register_driver boilerplate PNP / ACPI: Use ACPI_COMPANION_SET() during initialization
2015-04-11switch drivers/char/mem.c to ->read_iter/->write_iterAl Viro1-9/+9
Note that _these_ guys have ->read() and ->write() left in place - they are eqiuvalent to what we'd get if we replaced those with NULL, but we are talking about hot paths here. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-04-11make new_sync_{read,write}() staticAl Viro2-4/+0
All places outside of core VFS that checked ->read and ->write for being NULL or called the methods directly are gone now, so NULL {read,write} with non-NULL {read,write}_iter will do the right thing in all cases. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-04-11Merge branch 'iocb' into for-nextAl Viro2-2/+1
2015-04-10ipmi_ssif: Use interruptible completion for waiting in the threadCorey Minyard1-3/+5
The code was using an normal completion, but that caused stuck task errors after a while. Use an interruptible one to avoid that. Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-04-10ipmi/powernv: Fix minor locking bugAlistair Popple1-0/+1
If ipmi_powernv_recv(...) is called without a current message it prints a warning and returns. However it fails to release the message lock causing the system to dead lock during any subsequent IPMI operations. This error path should never normally be taken unless there are bugs elsewhere in the system. Signed-off-by: Alistair Popple <alistair@popple.id.au> Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-04-10ipmi: Handle BMCs that don't allow clearing the rcv irq bitCorey Minyard1-7/+102
Some BMCs don't let you clear the receive irq bit in the global enables. This is kind of silly, but they give an error if you try to clear it. Compensate for this by detecting the situation and working around it. Signed-off-by: Corey Minyard <cminyard@mvista.com> Tested-by: Thomas D <whissi@whissi.de> Reviewed-by: Thomas D <whissi@whissi.de>
2015-04-03char: xillybus: Don't return -EFAULT on user-triggered flushEli Billauer1-0/+2
The API allows the application to flush a host-to-FPGA stream by calling write() with the data count set to zero. Before this patch, copy_from_user() was called with a non-zero byte count, which possibly made it attempt to read from unmapped user memory. Such attempts caused the driver to return -EFAULT instead of 0, even though the desired operation went through fine. This patch ensures the driver returns 0 on a successful flush. Signed-off-by: Eli Billauer <eli.billauer@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-03virtio_console: Use bool function return values of true/false not 1/0Joe Perches1-1/+1
Use the normal return values for bool functions Signed-off-by: Joe Perches <joe@perches.com> Reviewed-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-03misc: pass miscdevice through file's private_dataTom Van Braeckel1-3/+8
Make the miscdevice accessible through the file's private_data. Previously, this was done only when an open() file operation had been registered. If no custom open() file operation was defined, private_data was set to NULL. This subtle quirk was confusing, to the point where kernel code registered *empty* file open operations to have private_data point to the misc device structure and avoid duplicating that logic. And it could easily lead to bugs, where the addition or removal of a custom open() file operation surprisingly changes the initial value of a file's private_data structure. To resolve this, we now place the miscdevice in the file's private_data member unconditionally when open() is called. Signed-off-by: Tom Van Braeckel <tomvanbraeckel@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-27tpm/st33zp24/spi: Add missing device table for spi phy.Christophe Ricard1-0/+7
MODULE_DEVICE_TABLE is missing in spi phy in case CONFIG_OF is not set. Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
2015-03-27tpm/st33zp24: Add proper wait for ordinal duration in case of irq modeChristophe Ricard1-1/+11
In case the driver is configured to use irq, we are not waiting the answer for a duration period to see the DATA_AVAIL status bit to raise but at maximum timeout_c. This may result in critical failure as we will not wait long enough for the command completion. Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Fixes: bf38b8710892 ("tpm/tpm_i2c_stm_st33: Split tpm_i2c_tpm_st33 in 2 layers (core + phy)") Reviewed-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
2015-03-25fs: move struct kiocb to fs.hChristoph Hellwig2-2/+1
struct kiocb now is a generic I/O container, so move it to fs.h. Also do a #include diet for aio.h while we're at it. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-03-25i8k: Remove use of seq_printf return valueJoe Perches1-7/+9
The seq_printf return value, because it's frequently misused, will eventually be converted to void. See: commit 1f33c41c03da ("seq_file: Rename seq_overflow() to seq_has_overflowed() and make public") Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-25hwrng: Avoid manual device_create_file() callsTakashi Iwai1-23/+11
Use the new group field of struct miscdevice for managing the sysfs entries instead of manually adding/removing via device_create_file() and device_remove_file(). This simplifies the code a lot and fixes the possible races. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-25misc: Add attribute groupsTakashi Iwai1-2/+3
Add groups field to struct miscdevice for passing the attribute groups at device creation. In this way, the driver can avoid the manual call of device_create_file() after the device registration, which is basically a racy operation, in addition to the reduction of manual device_remove_file() calls. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-25char: misc: document behaviour of open()Martin Kepplinger1-1/+3
an open syscall now assignes file->private_data to a pointer to the miscdevice structure. This reminds people not to duplicate code if they want this and not to depend on it being NULL. Signed-off-by: Martin Kepplinger <martink@posteo.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-25Merge 4.0-rc5 into char-misc-nextGreg Kroah-Hartman4-29/+40
We want those fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-18tpm/tpm_infineon: Use struct dev_pm_ops for power managementPeter Huewe1-25/+9
Make the tpm_infineon driver define its PM callbacks through a struct dev_pm_ops object rather than by using legacy PM hooks in struct pnp_driver. This allows the driver to use tpm_pm_suspend() as its suspend callback directly, so we can remove the duplicated savestate code. Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
2015-03-18tpm: Update KConfig text to include TPM2.0 FIFO chipsPeter Huewe1-4/+5
I got a lot of requests lately about whether the new TPM2.0 support includes the FIFO interface for TPM2.0 as well. The FIFO interface is handled by tpm_tis since FIFO=TIS (more or less). -> Update the helptext and headline Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
2015-03-18tpm/st33zp24/spi: Add st33zp24 spi phyChristophe Ricard5-2/+408
st33zp24 TIS 1.2 support also SPI. It is using a proprietary protocol to transport TIS data. Acked-by: Jarkko Sakkinen <jarkko.sakknen@linux.intel.com> Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
2015-03-18tpm/tpm_i2c_stm_st33: Split tpm_i2c_tpm_st33 in 2 layers (core + phy)Christophe Ricard8-926/+1031
tpm_i2c_stm_st33 is a TIS 1.2 TPM with a core interface which can be used by different phy such as i2c or spi. The core part is called st33zp24 which is also the main part reference. include/linux/platform_data/tpm_stm_st33.h is renamed consequently. The driver is also split into an i2c phy in charge of sending/receiving data as well as managing platform data or dts configuration. Acked-by: Jarkko Sakkinen <jarkko.sakknen@linux.intel.com> Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
2015-03-18tpm/tpm_i2c_stm_st33: Replace access to io_lpcpd from struct ↵Christophe Ricard1-7/+11
st33zp24_platform_data to tpm_stm_dev io_lpcpd is accessible from struct tpm_stm_dev. struct st33zp24_platform_data is only valid when using static platform configuration data, not when using dts. Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
2015-03-18tpm: fix: sanitized code paths in tpm_chip_register()Jarkko Sakkinen1-24/+42
I started to work with PPI interface so that it would be available under character device sysfs directory and realized that chip registeration was still too messy. In TPM 1.x in some rare scenarios (errors that almost never occur) wrong order in deinitialization steps was taken in teardown. I reproduced these scenarios by manually inserting error codes in the place of the corresponding function calls. The key problem is that the teardown is messy with two separate code paths (this was inherited when moving code from tpm-interface.c). Moved TPM 1.x specific register/unregister functionality to own helper functions and added single code path for teardown in tpm_chip_register(). Now the code paths have been fixed and it should be easier to review later on this part of the code. Cc: <stable@vger.kernel.org> Fixes: 7a1d7e6dd76a ("tpm: TPM 2.0 baseline support") Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Scot Doyle <lkml14@scotdoyle.com> Reviewed-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
2015-03-18PNP: tpm/tpm_infineon: Use module_pnp_driver to register driverPeter Huewe1-12/+1
Removing some boilerplate by using module_pnp_driver instead of calling register and unregister in the otherwise empty init/exit functions Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-03-18hwrng: core - allow perfect entropy from hardware devicesKeith Packard1-1/+2
Hardware random number quality is measured from 0 (no entropy) to 1024 (perfect entropy). Allow hardware devices to assert the full range by truncating the device-provided value at 1024 instead of 1023. Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2015-03-17Merge tag 'virtio-next-for-linus' of ↵Linus Torvalds1-1/+18
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux Pull virtio fixes from Rusty Russell: "Not entirely surprising: the ongoing QEMU work on virtio 1.0 has revealed more minor issues with our virtio 1.0 drivers just introduced in the kernel. (I would normally use my fixes branch for this, but there were a batch of them...)" * tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: virtio_mmio: fix access width for mmio uapi/virtio_scsi: allow overriding CDB/SENSE size virtio_mmio: generation support virtio_rpmsg: set DRIVER_OK before using device 9p/trans_virtio: fix hot-unplug virtio-balloon: do not call blocking ops when !TASK_RUNNING virtio_blk: fix comment for virtio 1.0 virtio_blk: typo fix virtio_balloon: set DRIVER_OK before using device virtio_console: avoid config access from irq virtio_console: init work unconditionally
2015-03-17hwrng: omap - Change RNG_CONFIG_REG to RNG_CONTROL_REG in initAndre Wolokita1-1/+1
omap4_rng_init() checks bit 10 of the RNG_CONFIG_REG to determine whether the RNG is already running before performing any initiliasation. This is not the correct register to check, as the enable bit is in RNG_CONFIG_CONTROL. Read from RNG_CONTROL_REG instead. Signed-off-by: Andre Wolokita <Andre.Wolokita@analog.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2015-03-17hwrng: omap - Change RNG_CONFIG_REG to RNG_CONTROL_REG when checking and ↵Andre Wolokita1-1/+1
disabling TRNG In omap4_rng_init(), a check of bit 10 of the RNG_CONFIG_REG is done to determine whether the RNG is running. This is suspicious firstly due to the use of RNG_CONTROL_ENABLE_TRNG_MASK and secondly because the same mask is written to RNG_CONTROL_REG after configuration of the FROs. Similar suspicious logic is repeated in omap4_rng_cleanup() when RNG_CONTROL_REG masked with RNG_CONTROL_ENABLE_TRNG_MASK is read, the same mask bit is cleared, and then written to RNG_CONFIG_REG. Unless the TRNG is enabled with one bit in RNG_CONTROL and disabled with another in RNG_CONFIG and these bits are mirrored in some way, I believe that the TRNG is not really shutting off. Apart from the strange logic, I have reason to suspect that the OMAP4 related code in this driver is driving an Inside Secure IP hardware RNG and strongly suspect that bit 10 of RNG_CONFIG_REG is one of the bits configuring the sampling rate of the FROs. This option is by default set to 0 and is not being set anywhere in omap-rng.c. Reading this bit during omap4_rng_init() will always return 0. It will remain 0 because ~(value of TRNG_MASK in control) will always be 0, because the TRNG is never shut off. This is of course presuming that the OMAP4 features the Inside Secure IP. I'm interested in knowing what the guys at TI think about this, as only they can confirm or deny the detailed structure of these registers. Signed-off-by: Andre Wolokita <Andre.Wolokita@analog.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2015-03-16char: constify of_device_id arrayFabian Frederick5-6/+6
of_device_id is always used as const. (See driver.of_match_table and open firmware functions) Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-16hwrng: iproc-rng200 - make use of devm_hwrng_registerDmitry Torokhov1-14/+1
This allows us to get rid of driver's remove() method. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>