summaryrefslogtreecommitdiffstats
path: root/drivers/char/tpm
AgeCommit message (Collapse)AuthorFilesLines
2021-08-23tpm: ibmvtpm: Avoid error message when process gets signal while waitingStefan Berger2-12/+16
When rngd is run as root then lots of these types of message will appear in the kernel log if the TPM has been configured to provide random bytes: [ 7406.275163] tpm tpm0: tpm_transmit: tpm_recv: error -4 The issue is caused by the following call that is interrupted while waiting for the TPM's response. sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd); Rather than waiting for the response in the low level driver, have it use the polling loop in tpm_try_transmit() that uses a command's duration to poll until a result has been returned by the TPM, thus ending when the timeout has occurred but not responding to signals and ctrl-c anymore. To stay in this polling loop extend tpm_ibmvtpm_status() to return 'true' for as long as the vTPM is indicated as being busy in tpm_processing_cmd. Since the loop requires the TPM's timeouts, get them now using tpm_get_timeouts() after setting the TPM2 version flag on the chip. To recreat the resolved issue start rngd like this: sudo rngd -r /dev/hwrng -t sudo rngd -r /dev/tpm0 -t Link: https://bugzilla.redhat.com/show_bug.cgi?id=1981473 Fixes: 6674ff145eef ("tpm_ibmvtpm: properly handle interrupted packet receptions") Cc: Nayna Jain <nayna@linux.ibm.com> Cc: George Wilson <gcwilson@linux.ibm.com> Reported-by: Nageswara R Sastry <rnsastry@linux.ibm.com> Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Tested-by: Nageswara R Sastry <rnsastry@linux.ibm.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-08-23char: tpm: cr50_i2c: convert to new probe interfaceAdrian Ratiu1-10/+2
Way back when this driver was written the I2C framework used to insist an ID table be defined even if the driver did not use it in favor of ACPI/OF matching, so it was added just to placate the hard I2C framework requirement. This is no longer the case so we can drop the table and also convert the driver to the new probe interface. Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-08-23char: tpm: Kconfig: remove bad i2c cr50 selectAdrian Ratiu1-1/+0
This fixes a minor bug which went unnoticed during the initial driver upstreaming review: TCG_CR50 does not exist in mainline kernels, so remove it. Fixes: 3a253caaad11 ("char: tpm: add i2c driver for cr50") Cc: stable@vger.kernel.org Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-07-21tpm_ftpm_tee: Free and unregister TEE shared memory during kexecTyler Hicks1-4/+4
dma-buf backed shared memory cannot be reliably freed and unregistered during a kexec operation even when tee_shm_free() is called on the shm from a .shutdown hook. The problem occurs because dma_buf_put() calls fput() which then uses task_work_add(), with the TWA_RESUME parameter, to queue tee_shm_release() to be called before the current task returns to user mode. However, the current task never returns to user mode before the kexec completes so the memory is never freed nor unregistered. Use tee_shm_alloc_kernel_buf() to avoid dma-buf backed shared memory allocation so that tee_shm_free() can directly call tee_shm_release(). This will ensure that the shm can be freed and unregistered during a kexec operation. Fixes: 09e574831b27 ("tpm/tpm_ftpm_tee: A driver for firmware TPM running inside TEE") Fixes: 1760eb689ed6 ("tpm/tpm_ftpm_tee: add shutdown call back") Cc: stable@vger.kernel.org Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com> Reviewed-by: Sumit Garg <sumit.garg@linaro.org> Acked-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
2021-06-23tpm: Replace WARN_ONCE() with dev_err_once() in tpm_tis_status()Jarkko Sakkinen2-8/+20
Do not tear down the system when getting invalid status from a TPM chip. This can happen when panic-on-warn is used. Instead, introduce TPM_TIS_INVALID_STATUS bitflag and use it to trigger once the error reporting per chip. In addition, print out the value of TPM_STS for improved forensics. Link: https://lore.kernel.org/keyrings/YKzlTR1AzUigShtZ@kroah.com/ Fixes: 55707d531af6 ("tpm_tis: Add a check for invalid status") Cc: stable@vger.kernel.org Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-06-23tpm_tis: Use DEFINE_RES_MEM() to simplify codeZhen Lei1-5/+1
Use DEFINE_RES_MEM() to save a couple of lines of code, which is simpler and more readable. The start address does not need to appear twice. Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-06-23tpm: fix some doc warnings in tpm1-cmd.cYang Yingliang1-2/+2
Fix the following make W=1 warnings: drivers/char/tpm/tpm1-cmd.c:325: warning: expecting prototype for tpm_startup(). Prototype was for tpm1_startup() instead drivers/char/tpm/tpm1-cmd.c:621: warning: expecting prototype for tpm_continue_selftest(). Prototype was for tpm1_continue_selftest() instead Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-06-23tpm_tis_spi: add missing SPI device ID entriesJavier Martinez Canillas1-0/+2
The SPI core always reports a "MODALIAS=spi:<foo>", even if the device was registered via OF. This means that this module won't auto-load if a DT has for example has a node with a compatible "infineon,slb9670" string. In that case kmod will expect a "MODALIAS=of:N*T*Cinfineon,slb9670" uevent but instead will get a "MODALIAS=spi:slb9670", which is not present in the kernel module aliases: $ modinfo drivers/char/tpm/tpm_tis_spi.ko | grep alias alias: of:N*T*Cgoogle,cr50C* alias: of:N*T*Cgoogle,cr50 alias: of:N*T*Ctcg,tpm_tis-spiC* alias: of:N*T*Ctcg,tpm_tis-spi alias: of:N*T*Cinfineon,slb9670C* alias: of:N*T*Cinfineon,slb9670 alias: of:N*T*Cst,st33htpm-spiC* alias: of:N*T*Cst,st33htpm-spi alias: spi:cr50 alias: spi:tpm_tis_spi alias: acpi*:SMO0768:* To workaround this issue, add in the SPI device ID table all the entries that are present in the OF device ID table. Reported-by: Alexander Wellbrock <a.wellbrock@mailbox.org> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-06-23tpm: add longer timeout for TPM2_CC_VERIFY_SIGNATUREAmir Mizinski1-1/+1
While running a TPM2_CC_VERIFY_SIGNATURE operation with RSA 3072-bit keys the TPM driver fails with the following error: "kernel: [ 2416.187522] tpm tpm0: Operation Timed out" Since the TPM PC Client specification does not specify a number for verify signature operation timeout, and the duration of TPM2_CC_VERIFY_SIGNATURE with RSA 3072-bit keys exceeds the current timeout of TPM_LONG (2 seconds), it is preferable to pick the longest timeout possible. Therefore, set the duration for TPM2_CC_VERIFY_SIGNATUE to TPM_LONG_LONG (5 minutes). [jarkko@kernel.org: mangled the short summary a bit] Link: https://trustedcomputinggroup.org/resource/pc-client-specific-platform-firmware-profile-specification/ Signed-off-by: Amir Mizinski <amirmizi6@gmail.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-06-23char: tpm: move to use request_irq by IRQF_NO_AUTOEN flagTian Tao1-2/+2
disable_irq() after request_irq() still has a time gap in which interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will disable IRQ auto-enable because of requesting. Link: https://lore.kernel.org/patchwork/patch/1388765/ Signed-off-by: Tian Tao <tiantao6@hisilicon.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-06-23tpm_tis_spi: set default probe function if device id not matchLiguang Zhang1-4/+8
In DSDT table, TPM _CID was SMO0768, and no _HID definition. After a kernel upgrade from 4.19 to 5.10, TPM probe function was changed which causes device probe fails. In order to make newer kernel to be compatible with the older acpi definition, it would be best set default probe function. Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-06-23tpm_crb: Use IOMEM_ERR_PTR when function returns iomemTian Tao1-1/+1
This is to simplify the code, and IOMEM_ERR_PTR(err) is same with (__force void __iomem *)ERR_PTR(err). Signed-off-by: Tian Tao <tiantao6@hisilicon.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-05-12tpm: fix error return code in tpm2_get_cc_attrs_tbl()Zhen Lei1-0/+1
If the total number of commands queried through TPM2_CAP_COMMANDS is different from that queried through TPM2_CC_GET_CAPABILITY, it indicates an unknown error. In this case, an appropriate error code -EFAULT should be returned. However, we currently do not explicitly assign this error code to 'rc'. As a result, 0 was incorrectly returned. Cc: stable@vger.kernel.org Fixes: 58472f5cd4f6("tpm: validate TPM 2.0 commands") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-05-12tpm, tpm_tis: Reserve locality in tpm_tis_resume()Jarkko Sakkinen1-2/+10
Reserve locality in tpm_tis_resume(), as it could be unsert after waking up from a sleep state. Cc: stable@vger.kernel.org Cc: Lino Sanfilippo <LinoSanfilippo@gmx.de> Reported-by: Hans de Goede <hdegoede@redhat.com> Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()") Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-05-12tpm, tpm_tis: Extend locality handling to TPM2 in tpm_tis_gen_interrupt()Jarkko Sakkinen1-6/+4
The earlier fix (linked) only partially fixed the locality handling bug in tpm_tis_gen_interrupt(), i.e. only for TPM 1.x. Extend the locality handling to cover TPM2. Cc: Hans de Goede <hdegoede@redhat.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/linux-integrity/20210220125534.20707-1-jarkko@kernel.org/ Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()") Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
2021-04-14char: tpm: fix error return code in tpm_cr50_i2c_tis_recv()Zhihao Cheng1-0/+1
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 3a253caaad11 ("char: tpm: add i2c driver for cr50") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-04-14tpm: vtpm_proxy: Avoid reading host log when using a virtual deviceStefan Berger1-0/+3
Avoid allocating memory and reading the host log when a virtual device is used since this log is of no use to that driver. A virtual device can be identified through the flag TPM_CHIP_FLAG_VIRTUAL, which is only set for the tpm_vtpm_proxy driver. Cc: stable@vger.kernel.org Fixes: 6f99612e2500 ("tpm: Proxy driver for supporting multiple emulated TPMs") Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-04-14tpm: acpi: Check eventlog signature before using itStefan Berger1-1/+32
Check the eventlog signature before using it. This avoids using an empty log, as may be the case when QEMU created the ACPI tables, rather than probing the EFI log next. This resolves an issue where the EFI log was empty since an empty ACPI log was used. Cc: stable@vger.kernel.org Fixes: 85467f63a05c ("tpm: Add support for event log pointer found in TPM2 ACPI table") Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-04-14tpm: efi: Use local variable for calculating final log sizeStefan Berger1-8/+21
When tpm_read_log_efi is called multiple times, which happens when one loads and unloads a TPM2 driver multiple times, then the global variable efi_tpm_final_log_size will at some point become a negative number due to the subtraction of final_events_preboot_size occurring each time. Use a local variable to avoid this integer underflow. The following issue is now resolved: Mar 8 15:35:12 hibinst kernel: Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 Mar 8 15:35:12 hibinst kernel: Workqueue: tpm-vtpm vtpm_proxy_work [tpm_vtpm_proxy] Mar 8 15:35:12 hibinst kernel: RIP: 0010:__memcpy+0x12/0x20 Mar 8 15:35:12 hibinst kernel: Code: 00 b8 01 00 00 00 85 d2 74 0a c7 05 44 7b ef 00 0f 00 00 00 c3 cc cc cc 66 66 90 66 90 48 89 f8 48 89 d1 48 c1 e9 03 83 e2 07 <f3> 48 a5 89 d1 f3 a4 c3 66 0f 1f 44 00 00 48 89 f8 48 89 d1 f3 a4 Mar 8 15:35:12 hibinst kernel: RSP: 0018:ffff9ac4c0fcfde0 EFLAGS: 00010206 Mar 8 15:35:12 hibinst kernel: RAX: ffff88f878cefed5 RBX: ffff88f878ce9000 RCX: 1ffffffffffffe0f Mar 8 15:35:12 hibinst kernel: RDX: 0000000000000003 RSI: ffff9ac4c003bff9 RDI: ffff88f878cf0e4d Mar 8 15:35:12 hibinst kernel: RBP: ffff9ac4c003b000 R08: 0000000000001000 R09: 000000007e9d6073 Mar 8 15:35:12 hibinst kernel: R10: ffff9ac4c003b000 R11: ffff88f879ad3500 R12: 0000000000000ed5 Mar 8 15:35:12 hibinst kernel: R13: ffff88f878ce9760 R14: 0000000000000002 R15: ffff88f77de7f018 Mar 8 15:35:12 hibinst kernel: FS: 0000000000000000(0000) GS:ffff88f87bd00000(0000) knlGS:0000000000000000 Mar 8 15:35:12 hibinst kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Mar 8 15:35:12 hibinst kernel: CR2: ffff9ac4c003c000 CR3: 00000001785a6004 CR4: 0000000000060ee0 Mar 8 15:35:12 hibinst kernel: Call Trace: Mar 8 15:35:12 hibinst kernel: tpm_read_log_efi+0x152/0x1a7 Mar 8 15:35:12 hibinst kernel: tpm_bios_log_setup+0xc8/0x1c0 Mar 8 15:35:12 hibinst kernel: tpm_chip_register+0x8f/0x260 Mar 8 15:35:12 hibinst kernel: vtpm_proxy_work+0x16/0x60 [tpm_vtpm_proxy] Mar 8 15:35:12 hibinst kernel: process_one_work+0x1b4/0x370 Mar 8 15:35:12 hibinst kernel: worker_thread+0x53/0x3e0 Mar 8 15:35:12 hibinst kernel: ? process_one_work+0x370/0x370 Cc: stable@vger.kernel.org Fixes: 166a2809d65b ("tpm: Don't duplicate events from the final event log in the TCG2 log") Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-03-07Merge tag 'powerpc-5.12-2' of ↵Linus Torvalds1-3/+1
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: "One non-fix, the conversion of vio_driver->remove() to return void, which touches various powerpc specific drivers. Fix the privilege checks we do in our perf handling, which could cause soft/hard lockups in some configurations. Fix a bug with IRQ affinity seen on kdump kernels when CPU 0 is offline in the second kernel. Fix missed page faults after mprotect(..., PROT_NONE) on 603 (32-bit). Fix a bug in our VSX (vector) instruction emulation, which should only be seen when doing VSX ops to cache inhibited mappings. Three commits fixing various build issues with obscure configurations. Thanks to Athira Rajeev, Cédric Le Goater, Christophe Leroy, Christoph Plattner, Greg Kurz, Jordan Niethe, Laurent Vivier, Ravi Bangoria, Tyrel Datwyler, and Uwe Kleine-König" * tag 'powerpc-5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/sstep: Fix VSX instruction emulation powerpc/perf: Fix handling of privilege level checks in perf interrupt context powerpc: Force inlining of mmu_has_feature to fix build failure vio: make remove callback return void powerpc/syscall: Force inlining of __prep_irq_for_enabled_exit() powerpc/603: Fix protection of user pages mapped with PROT_NONE powerpc/pseries: Don't enforce MSI affinity with kdump powerpc/4xx: Fix build errors from mfdcr()
2021-03-03tpm: Remove unintentional dump_stack() callJarkko Sakkinen1-2/+0
Somewhere along the line, probably during a rebase, an unintentional dump_stack() got included. Revert this change. Reported-by: Rikard Falkeborn <rikard.falkeborn@gmail.com> Fixes: 90cba8d20f8b ("tpm/ppi: Constify static struct attribute_group") Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-03-02vio: make remove callback return voidUwe Kleine-König1-3/+1
The driver core ignores the return value of struct bus_type::remove() because there is only little that can be done. To simplify the quest to make this function return void, let struct vio_driver::remove() return void, too. All users already unconditionally return 0, this commit makes it obvious that returning an error code is a bad idea. Note there are two nominally different implementations for a vio bus: one in arch/sparc/kernel/vio.c and the other in arch/powerpc/platforms/pseries/vio.c. This patch only adapts the powerpc one. Before this patch for a device that was bound to a driver without a remove callback vio_cmo_bus_remove(viodev) wasn't called. As the device core still considers the device unbound after vio_bus_remove() returns calling this unconditionally is the consistent behaviour which is implemented here. Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com> Acked-by: Lijun Pan <ljp@linux.ibm.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [mpe: Drop unneeded hvcs_remove() forward declaration, squash in change from sfr to drop ibmvnic_remove() forward declaration] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210225221834.160083-1-uwe@kleine-koenig.org
2021-02-24tpm, tpm_tis: Decorate tpm_tis_gen_interrupt() with request_locality()Lukasz Majczak1-3/+13
This is shown with Samsung Chromebook Pro (Caroline) with TPM 1.2 (SLB 9670): [ 4.324298] TPM returned invalid status [ 4.324806] WARNING: CPU: 2 PID: 1 at drivers/char/tpm/tpm_tis_core.c:275 tpm_tis_status+0x86/0x8f Background ========== TCG PC Client Platform TPM Profile (PTP) Specification, paragraph 6.1 FIFO Interface Locality Usage per Register, Table 39 Register Behavior Based on Locality Setting for FIFO - a read attempt to TPM_STS_x Registers returns 0xFF in case of lack of locality. The fix ======= Decorate tpm_tis_gen_interrupt() with request_locality() and release_locality(). Cc: Laurent Bigonville <bigon@debian.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: stable@vger.kernel.org Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()") Signed-off-by: Lukasz Majczak <lma@semihalf.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-02-24tpm, tpm_tis: Decorate tpm_get_timeouts() with request_locality()Jarkko Sakkinen1-2/+12
This is shown with Samsung Chromebook Pro (Caroline) with TPM 1.2 (SLB 9670): [ 4.324298] TPM returned invalid status [ 4.324806] WARNING: CPU: 2 PID: 1 at drivers/char/tpm/tpm_tis_core.c:275 tpm_tis_status+0x86/0x8f Background ========== TCG PC Client Platform TPM Profile (PTP) Specification, paragraph 6.1 FIFO Interface Locality Usage per Register, Table 39 Register Behavior Based on Locality Setting for FIFO - a read attempt to TPM_STS_x Registers returns 0xFF in case of lack of locality. The fix ======= Decorate tpm_get_timeouts() with request_locality() and release_locality(). Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()") Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Laurent Bigonville <bigon@debian.org> Cc: stable@vger.kernel.org Reported-by: Lukasz Majczak <lma@semihalf.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-02-16KEYS: trusted: Reserve TPM for seal and unseal operationsJarkko Sakkinen1-4/+0
When TPM 2.0 trusted keys code was moved to the trusted keys subsystem, the operations were unwrapped from tpm_try_get_ops() and tpm_put_ops(), which are used to take temporarily the ownership of the TPM chip. The ownership is only taken inside tpm_send(), but this is not sufficient, as in the key load TPM2_CC_LOAD, TPM2_CC_UNSEAL and TPM2_FLUSH_CONTEXT need to be done as a one single atom. Take the TPM chip ownership before sending anything with tpm_try_get_ops() and tpm_put_ops(), and use tpm_transmit_cmd() to send TPM commands instead of tpm_send(), reverting back to the old behaviour. Fixes: 2e19e10131a0 ("KEYS: trusted: Move TPM2 trusted keys code") Reported-by: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Cc: stable@vger.kernel.org Cc: David Howells <dhowells@redhat.com> Cc: Mimi Zohar <zohar@linux.ibm.com> Cc: Sumit Garg <sumit.garg@linaro.org> Acked-by Sumit Garg <sumit.garg@linaro.org> Tested-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-02-16tpm/ppi: Constify static struct attribute_groupRikard Falkeborn2-1/+3
The only usage of ppi_attr_grp is to put its address in an array of pointers to const struct attribute_group. Make it const to allow the compiler to put it in read-only memory. Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-02-16tpm: add sysfs exports for all banks of PCR registersJames Bottomley1-0/+179
Create sysfs per hash groups with 24 PCR files in them one group, named pcr-<hash>, for each agile hash of the TPM. The files are plugged in to a PCR read function which is TPM version agnostic, so this works also for TPM 1.2 but the hash is only sha1 in that case. Note: the macros used to create the hashes emit spurious checkpatch warnings. Do not try to "fix" them as checkpatch recommends, otherwise they'll break. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Tested-by: Thiago Jung Bauermann <bauerman@linux.ibm.com> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-02-16tpm: Remove tpm_dev_wq_lockSebastian Andrzej Siewior1-1/+0
Never used since it was added. Fixes: 9e1b74a63f776 ("tpm: add support for nonblocking operation") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-integrity@vger.kernel.org Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Philip Tricca <philip.b.tricca@intel.com> Cc: Tadeusz Struk <tadeusz.struk@intel.com> Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-02-16char: tpm: add i2c driver for cr50Duncan Laurie3-0/+802
Add TPM 2.0 compatible I2C interface for chips with cr50 firmware. The firmware running on the currently supported H1 MCU requires a special driver to handle its specific protocol, and this makes it unsuitable to use tpm_tis_core_* and instead it must implement the underlying TPM protocol similar to the other I2C TPM drivers. - All 4 bytes of status register must be read/written at once. - FIFO and burst count is limited to 63 and must be drained by AP. - Provides an interrupt to indicate when read response data is ready and when the TPM is finished processing write data. This driver is based on the existing infineon I2C TPM driver, which most closely matches the cr50 i2c protocol behavior. Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com> Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com> Tested-by: Adrian Ratiu <adrian.ratiu@collabora.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-02-16tpm: Fix fall-through warnings for ClangGustavo A. R. Silva1-0/+1
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning by explicitly adding a break statement instead of letting the code fall through to the next case. Link: https://github.com/KSPP/linux/issues/115 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-02-16tpm_tis: Clean up locality releaseJames Bottomley1-46/+1
The current release locality code seems to be based on the misunderstanding that the TPM interrupts when a locality is released: it doesn't, only when the locality is acquired. Furthermore, there seems to be no point in waiting for the locality to be released. All it does is penalize the last TPM user. However, if there's no next TPM user, this is a pointless wait and if there is a next TPM user, they'll pay the penalty waiting for the new locality (or possibly not if it's the same as the old locality). Fix the code by making release_locality as simple write to release with no waiting for completion. Cc: stable@ger.kernel.org Fixes: 33bafe90824b ("tpm_tis: verify locality released before returning from release_locality") Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-02-16tpm_tis: Fix check_locality for correct locality acquisitionJames Bottomley1-1/+2
The TPM TIS specification says the TPM signals the acquisition of locality when the TMP_ACCESS_REQUEST_USE bit goes to one *and* the TPM_ACCESS_REQUEST_USE bit goes to zero. Currently we only check the former not the latter, so check both. Adding the check on TPM_ACCESS_REQUEST_USE should fix the case where the locality is re-requested before the TPM has released it. In this case the locality may get released briefly before it is reacquired, which causes all sorts of problems. However, with the added check, TPM_ACCESS_REQUEST_USE should remain 1 until the second request for the locality is granted. Cc: stable@ger.kernel.org Fixes: 27084efee0c3 ("[PATCH] tpm: driver for next generation TPM chips") Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2020-11-06tpm: efi: Don't create binary_bios_measurements file for an empty logTyler Hicks1-0/+5
Mimic the pre-existing ACPI and Device Tree event log behavior by not creating the binary_bios_measurements file when the EFI TPM event log is empty. This fixes the following NULL pointer dereference that can occur when reading /sys/kernel/security/tpm0/binary_bios_measurements after the kernel received an empty event log from the firmware: BUG: kernel NULL pointer dereference, address: 000000000000002c #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 2 PID: 3932 Comm: fwupdtpmevlog Not tainted 5.9.0-00003-g629990edad62 #17 Hardware name: LENOVO 20LCS03L00/20LCS03L00, BIOS N27ET38W (1.24 ) 11/28/2019 RIP: 0010:tpm2_bios_measurements_start+0x3a/0x550 Code: 54 53 48 83 ec 68 48 8b 57 70 48 8b 1e 65 48 8b 04 25 28 00 00 00 48 89 45 d0 31 c0 48 8b 82 c0 06 00 00 48 8b 8a c8 06 00 00 <44> 8b 60 1c 48 89 4d a0 4c 89 e2 49 83 c4 20 48 83 fb 00 75 2a 49 RSP: 0018:ffffa9c901203db0 EFLAGS: 00010246 RAX: 0000000000000010 RBX: 0000000000000000 RCX: 0000000000000010 RDX: ffff8ba1eb99c000 RSI: ffff8ba1e4ce8280 RDI: ffff8ba1e4ce8258 RBP: ffffa9c901203e40 R08: ffffa9c901203dd8 R09: ffff8ba1ec443300 R10: ffffa9c901203e50 R11: 0000000000000000 R12: ffff8ba1e4ce8280 R13: ffffa9c901203ef0 R14: ffffa9c901203ef0 R15: ffff8ba1e4ce8258 FS: 00007f6595460880(0000) GS:ffff8ba1ef880000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000002c CR3: 00000007d8d18003 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ? __kmalloc_node+0x113/0x320 ? kvmalloc_node+0x31/0x80 seq_read+0x94/0x420 vfs_read+0xa7/0x190 ksys_read+0xa7/0xe0 __x64_sys_read+0x1a/0x20 do_syscall_64+0x37/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xa9 In this situation, the bios_event_log pointer in the tpm_bios_log struct was not NULL but was equal to the ZERO_SIZE_PTR (0x10) value. This was due to the following kmemdup() in tpm_read_log_efi(): int tpm_read_log_efi(struct tpm_chip *chip) { ... /* malloc EventLog space */ log->bios_event_log = kmemdup(log_tbl->log, log_size, GFP_KERNEL); if (!log->bios_event_log) { ret = -ENOMEM; goto out; } ... } When log_size is zero, due to an empty event log from firmware, ZERO_SIZE_PTR is returned from kmemdup(). Upon a read of the binary_bios_measurements file, the tpm2_bios_measurements_start() function does not perform a ZERO_OR_NULL_PTR() check on the bios_event_log pointer before dereferencing it. Rather than add a ZERO_OR_NULL_PTR() check in functions that make use of the bios_event_log pointer, simply avoid creating the binary_bios_measurements_file as is done in other event log retrieval backends. Explicitly ignore all of the events in the final event log when the main event log is empty. The list of events in the final event log cannot be accurately parsed without referring to the first event in the main event log (the event log header) so the final event log is useless in such a situation. Fixes: 58cc1e4faf10 ("tpm: parse TPM event logs based on EFI table") Link: https://lore.kernel.org/linux-integrity/E1FDCCCB-CA51-4AEE-AC83-9CDE995EAE52@canonical.com/ Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reported-by: Kenneth R. Crudup <kenny@panix.com> Reported-by: Mimi Zohar <zohar@linux.ibm.com> Cc: Thiébaud Weksteen <tweek@google.com> Cc: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2020-11-06tpm_tis: Disable interrupts on ThinkPad T490sJerry Snitselaar1-2/+27
There is a misconfiguration in the bios of the gpio pin used for the interrupt in the T490s. When interrupts are enabled in the tpm_tis driver code this results in an interrupt storm. This was initially reported when we attempted to enable the interrupt code in the tpm_tis driver, which previously wasn't setting a flag to enable it. Due to the reports of the interrupt storm that code was reverted and we went back to polling instead of using interrupts. Now that we know the T490s problem is a firmware issue, add code to check if the system is a T490s and disable interrupts if that is the case. This will allow us to enable interrupts for everyone else. If the user has a fixed bios they can force the enabling of interrupts with tpm_tis.interrupts=1 on the kernel command line. Cc: Peter Huewe <peterhuewe@gmx.de> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2020-10-02tpm_tis: Add a check for invalid statusJames Bottomley2-0/+12
Some TIS based TPMs can return 0xff to status reads if the locality hasn't been properly requested. Detect this condition by checking the bits that the TIS spec specifies must return zero are clear and return zero in that case. Also drop a warning so the problem can be identified in the calling path and fixed (usually a missing try_get_ops()). Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-10-02tpm: use %*ph to print small bufferAndy Shevchenko1-21/+10
Use %*ph format to print small buffer as hex string. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Petr Vorel <pvorel@suse.cz> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-10-02tpm: tis: add support for MMIO TPM on SynQuacerMasahisa Kojima3-0/+221
When fitted, the SynQuacer platform exposes its SPI TPM via a MMIO window that is backed by the SPI command sequencer in the SPI bus controller. This arrangement has the limitation that only byte size accesses are supported, and so we'll need to provide a separate module that take this into account. Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-08-03Merge tag 'arm-drivers-5.9' of ↵Linus Torvalds1-10/+60
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC driver updates from Arnd Bergmann: "A couple of subsystems have their own subsystem maintainers but choose to have the code merged through the soc tree as upstream, as the code tends to be used across multiple SoCs or has SoC specific drivers itself: - memory controllers: Krzysztof Kozlowski takes ownership of the drivers/memory subsystem and its drivers, starting out with a set of cleanup patches. A larger driver for the Tegra memory controller that was accidentally missed for v5.8 is now added. - reset controllers: Only minor updates to drivers/reset this time - firmware: The "turris mox" firmware driver gains support for signed firmware blobs The tegra firmware driver gets extended to export some debug information Various updates to i.MX firmware drivers, mostly cosmetic - ARM SCMI/SCPI: A new mechanism for platform notifications is added, among a number of minor changes. - optee: Probing of the TEE bus is rewritten to better support detection of devices that depend on the tee-supplicant user space. A new firmware based trusted platform module (fTPM) driver is added based on OP-TEE - SoC attributes: A new driver is added to provide a generic soc_device for identifying a machine through the SMCCC ARCH_SOC_ID firmware interface rather than by probing SoC family specific registers. The series also contains some cleanups to the common soc_device code. There are also a number of updates to SoC specific drivers, the main ones are: - Mediatek cmdq driver gains a few in-kernel interfaces - Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding support for additional SoC variants - The Qualcomm GENI core code gains interconnect path voting and performance level support, and integrating this into a number of device drivers. - A new driver for Samsung Exynos5800 voltage coupler for - Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC specific device drivers - Updates to the TI K3 Ring Accelerator driver" * tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits) soc: qcom: geni: Fix unused label warning soc: qcom: smd-rpm: Fix kerneldoc memory: jz4780_nemc: Only request IO memory the driver will use soc: qcom: pdr: Reorder the PD state indication ack MAINTAINERS: Add Git repository for memory controller drivers memory: brcmstb_dpfe: Fix language typo memory: samsung: exynos5422-dmc: Correct white space issues memory: samsung: exynos-srom: Correct alignment memory: pl172: Enclose macro argument usage in parenthesis memory: of: Correct kerneldoc memory: omap-gpmc: Fix language typo memory: omap-gpmc: Correct white space issues memory: omap-gpmc: Use 'unsigned int' for consistency memory: omap-gpmc: Enclose macro argument usage in parenthesis memory: omap-gpmc: Correct kerneldoc memory: mvebu-devbus: Align with open parenthesis memory: mvebu-devbus: Add missing braces to all arms of if statement memory: bt1-l2-ctl: Add blank lines after declarations soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static firmware: ti_sci: Replace HTTP links with HTTPS ones ...
2020-07-24tpm: Add support for event log pointer found in TPM2 ACPI tableStefan Berger1-21/+42
In case a TPM2 is attached, search for a TPM2 ACPI table when trying to get the event log from ACPI. If one is found, use it to get the start and length of the log area. This allows non-UEFI systems, such as SeaBIOS, to pass an event log when using a TPM2. Cc: Peter Huewe <peterhuewe@gmx.de> Cc: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-07-24tpm: Unify the mismatching TPM space buffer sizesJarkko Sakkinen4-19/+23
The size of the buffers for storing context's and sessions can vary from arch to arch as PAGE_SIZE can be anything between 4 kB and 256 kB (the maximum for PPC64). Define a fixed buffer size set to 16 kB. This should be enough for most use with three handles (that is how many we allow at the moment). Parametrize the buffer size while doing this, so that it is easier to revisit this later on if required. Cc: stable@vger.kernel.org Reported-by: Stefan Berger <stefanb@linux.ibm.com> Fixes: 745b361e989a ("tpm: infrastructure for TPM spaces") Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Tested-by: Stefan Berger <stefanb@linux.ibm.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-07-13Merge tag 'optee-bus-for-v5.9' of ↵Arnd Bergmann1-10/+60
git://git.linaro.org/people/jens.wiklander/linux-tee into arm/drivers Enable multi-stage OP-TEE bus enumeration Probes drivers on the OP-TEE bus in two steps. First for drivers which do not depend on tee-supplicant. After tee-supplicant has been started probe the devices which do depend on tee-supplicant. Also introduces driver which uses an OP-TEE based fTPM Trusted Application depends on tee-supplicant NV RAM implementation based on RPMB secure storage. * tag 'optee-bus-for-v5.9' of git://git.linaro.org/people/jens.wiklander/linux-tee: tpm_ftpm_tee: register driver on TEE bus optee: enable support for multi-stage bus enumeration optee: use uuid for sysfs driver entry Link: https://lore.kernel.org/r/20200710085230.GA1312913@jade Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-10tpm_ftpm_tee: register driver on TEE busMaxim Uvarov1-10/+60
OP-TEE based fTPM Trusted Application depends on tee-supplicant to provide NV RAM implementation based on RPMB secure storage. So this dependency can be resolved via TEE bus where we only invoke fTPM driver probe once fTPM device is registered on the bus which is only true after the tee-supplicant is up and running. Additionally, TEE bus provides auto device enumeration. Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org> Suggested-by: Sumit Garg <sumit.garg@linaro.org> Suggested-by: Arnd Bergmann <arnd@linaro.org> Reviewed-by: Sumit Garg <sumit.garg@linaro.org> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Sumit Garg <sumit.garg@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
2020-07-07Revert commit e918e570415c ("tpm_tis: Remove the HID IFX0102")Jarkko Sakkinen1-0/+8
Removing IFX0102 from tpm_tis was not a right move because both tpm_tis and tpm_infineon use the same device ID. Revert the commit and add a remark about a bug caused by commit 93e1b7d42e1e ("[PATCH] tpm: add HID module parameter"). Fixes: e918e570415c ("tpm_tis: Remove the HID IFX0102") Reported-by: Peter Huewe <peterhuewe@gmx.de> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-07-02tpm_tis: Remove the HID IFX0102Jarkko Sakkinen1-1/+0
Acer C720 running Linux v5.3 reports this in klog: tpm_tis: 1.2 TPM (device-id 0xB, rev-id 16) tpm tpm0: tpm_try_transmit: send(): error -5 tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts tpm_tis tpm_tis: Could not get TPM timeouts and durations tpm_tis 00:08: 1.2 TPM (device-id 0xB, rev-id 16) tpm tpm0: tpm_try_transmit: send(): error -5 tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts tpm_tis 00:08: Could not get TPM timeouts and durations ima: No TPM chip found, activating TPM-bypass! tpm_inf_pnp 00:08: Found TPM with ID IFX0102 % git --no-pager grep IFX0102 drivers/char/tpm drivers/char/tpm/tpm_infineon.c: {"IFX0102", 0}, drivers/char/tpm/tpm_tis.c: {"IFX0102", 0}, /* Infineon */ Obviously IFX0102 was added to the HID table for the TCG TIS driver by mistake. Fixes: 93e1b7d42e1e ("[PATCH] tpm: add HID module parameter") Link: https://bugzilla.kernel.org/show_bug.cgi?id=203877 Cc: stable@vger.kernel.org Cc: Kylene Jo Hall <kjhall@us.ibm.com> Reported-by: Ferry Toth: <ferry.toth@elsinga.info> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-07-02tpm_tis_spi: Prefer async probeDouglas Anderson1-0/+1
On a Chromebook I'm working on I noticed a big (~1 second) delay during bootup where nothing was happening. Right around this big delay there were messages about the TPM: [ 2.311352] tpm_tis_spi spi0.0: TPM ready IRQ confirmed on attempt 2 [ 3.332790] tpm_tis_spi spi0.0: Cr50 firmware version: ... I put a few printouts in and saw that tpm_tis_spi_init() (specifically tpm_chip_register() in that function) was taking the lion's share of this time, though ~115 ms of the time was in cr50_print_fw_version(). Let's make a one-line change to prefer async probe for tpm_tis_spi. There's no reason we need to block other drivers from probing while we load. NOTES: * It's possible that other hardware runs through the init sequence faster than Cr50 and this isn't such a big problem for them. However, even if they are faster they are still doing _some_ transfers over a SPI bus so this should benefit everyone even if to a lesser extent. * It's possible that there are extra delays in the code that could be optimized out. I didn't dig since once I enabled async probe they no longer impacted me. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-07-02tpm: ibmvtpm: Wait for ready buffer before probing for TPM2 attributesDavid Gibson1-7/+7
The tpm2_get_cc_attrs_tbl() call will result in TPM commands being issued, which will need the use of the internal command/response buffer. But, we're issuing this *before* we've waited to make sure that buffer is allocated. This can result in intermittent failures to probe if the hypervisor / TPM implementation doesn't respond quickly enough. I find it fails almost every time with an 8 vcpu guest under KVM with software emulated TPM. To fix it, just move the tpm2_get_cc_attrs_tlb() call after the existing code to wait for initialization, which will ensure the buffer is allocated. Fixes: 18b3670d79ae9 ("tpm: ibmvtpm: Add support for TPM2") Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-07-02tpm/st33zp24: fix spelling mistake "drescription" -> "description"Binbin Zhou3-4/+4
Trivial fix, the spelling of "drescription" is incorrect in function comment. Fix this. Signed-off-by: Binbin Zhou <zhoubinbin@uniontech.com> Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-07-02tpm_tis: extra chip->ops check on error path in tpm_tis_core_initVasily Averin1-1/+1
Found by smatch: drivers/char/tpm/tpm_tis_core.c:1088 tpm_tis_core_init() warn: variable dereferenced before check 'chip->ops' (see line 979) 'chip->ops' is assigned in the beginning of function in tpmm_chip_alloc->tpm_chip_alloc and is used before first possible goto to error path. Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-07-02tpm_tis_spi: Don't send anything during flow controlDouglas Anderson1-5/+4
During flow control we are just reading from the TPM, yet our spi_xfer has the tx_buf and rx_buf both non-NULL which means we're requesting a full duplex transfer. SPI is always somewhat of a full duplex protocol anyway and in theory the other side shouldn't really be looking at what we're sending it during flow control, but it's still a bit ugly to be sending some "random" data when we shouldn't. The default tpm_tis_spi_flow_control() tries to address this by setting 'phy->iobuf[0] = 0'. This partially avoids the problem of sending "random" data, but since our tx_buf and rx_buf both point to the same place I believe there is the potential of us sending the TPM's previous byte back to it if we hit the retry loop. Another flow control implementation, cr50_spi_flow_control(), doesn't address this at all. Let's clean this up and just make the tx_buf NULL before we call flow_control(). Not only does this ensure that we're not sending any "random" bytes but it also possibly could make the SPI controller behave in a slightly more optimal way. NOTE: no actual observed problems are fixed by this patch--it's was just made based on code inspection. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2020-07-02tpm: Fix TIS locality timeout problemsJames Bottomley1-10/+9
It has been reported that some TIS based TPMs are giving unexpected errors when using the O_NONBLOCK path of the TPM device. The problem is that some TPMs don't like it when you get and then relinquish a locality (as the tpm_try_get_ops()/tpm_put_ops() pair does) without sending a command. This currently happens all the time in the O_NONBLOCK write path. Fix this by moving the tpm_try_get_ops() further down the code to after the O_NONBLOCK determination is made. This is safe because the priv->buffer_mutex still protects the priv state being modified. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206275 Fixes: d23d12484307 ("tpm: fix invalid locking in NONBLOCKING mode") Reported-by: Mario Limonciello <Mario.Limonciello@dell.com> Tested-by: Alex Guzman <alex@guzman.io> Cc: stable@vger.kernel.org Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-10 01:26:18 +0000