| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When the device is idle it is possible to move it into the lowest MHI
PM state (M3). In that mode, all MHI operations are suspended and the
PCI device can be safely put into PCI D3 state.
The device is then resumed from D3/M3 either because of host initiated
MHI operation (e.g. buffer TX) or because the device (modem) has
triggered wake-up via PME feature (e.g. on incoming data).
Same procedures can be used for system wide or runtime suspend/resume.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1614971808-22156-6-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The PCI core can take care of proper PCI suspend/resume operations, but
this is discarded when the driver saves PCI state by its own. This
currently prevents the PCI core to enable PME (for modem initiated
D3 exit) which is requested for proper runtime pm support.
This change deletes explicit PCI state-saving and state-set from
suspend callback, letting the PCI doing the appropriate work.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1614971808-22156-5-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The wake_db register presence is highly speculative and can fuze MHI
devices. Indeed, currently the wake_db register address is defined at
entry 127 of the 'Channel doorbell array', thus writing to this address
is equivalent to ringing the doorbell for channel 127, causing trouble
with some devics (e.g. SDX24 based modems) that get an unexpected
channel 127 doorbell interrupt.
This change fixes that issue by setting wake get/put as no-op for
pci_generic devices. The wake device sideband mechanism seems really
specific to each device, and is AFAIK not defined by the MHI spec.
It also removes zeroing initialization of wake_db register during MMIO
initialization, the register being set via wake_get/put accessors few
cycles later during M0 transition.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1614971808-22156-4-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add generic info for SDX24 based modems. Also add the FIREHOSE channels
used by the flash-programmer firmware loaded in EDL mode.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1614971808-22156-3-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add support for EM1XXGR-L modems, this modem series is based on SDX24
qcom chip. The modem is mainly based on MBIM protocol for both the
data and control path. The drivers for these channels (mhi-net-mbim and
mhi_uci) are not yet part of the kernel but will be integrated by
different series.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1614971808-22156-2-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Not all hardwares need to use the same number of event ring elements.
This change makes this parametrable.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1614971808-22156-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
We met some sporadic modem crashes during high throughput testing, this
has been root caused to a lack of elements in the event ring. Indeed,
the modem is simply crashing when event ring becomes empty.
It appears that the total number event ring elements is too low given
the performances of the modem (IPA hardware accelerator). This change
increases the number of elements in the hardware event ring to 2048,
which is aligned with what is defined in downstream version:
https://source.codeaurora.org/quic/la/kernel/msm-4.14/tree/arch/arm64/boot/dts/qcom/sm8150-mhi.dtsi?h=msm-4.14#n482
With this change, modem coes not crash anymore.
Note: An event ring element is 16-Byte, so the total memory usage of
a hardware event ring is now 32KB.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1612514195-8257-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Print warning when MHI detects sys error.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1612370382-21643-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
When a shared MSI vector must be used (e.g. when VTd is disabled on
x86_64), each event MSI vector must be set to the shared vector idx.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar<hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
MHI hardware channels are usually the hardware accelerated data path
e.g. IP packets path for modems. This path needs to be optimized for
low latency and high throughput. After several tests on FN980m SDX55
based modem, it seems 1ms is a good default irq_moderation value:
- It allows to reach the maximum download throughput
- It introduces limited latency (5ms is too high)
- It prevents interrupt flooding
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add support for Diag over MHI. Qualcomm Diag is the qualcomm
diagnostics interface that can be used to collect modem logs,
events, traces, etc. It can be used by tools such QPST or QXDM.
This patch adds the DIAG channels and a dedicated event ring.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
On cold boot, device can take slightly more than 5 seconds to start.
Increase the timeout to prevent MHI power-up issues.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
If the modem crashes for any reason, we may not be able to detect
it at MHI level (MHI registers not reachable anymore).
This patch implements a health-check mechanism to check regularly
that device is alive (MHI layer can communicate with). If device
is not alive (because a crash or unexpected reset), the recovery
procedure is triggered.
Tested successfully with Telit FN980m module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
In AER capable root complex, errors are reported to the host which
can then act accordingly and perform PCI recovering procedure.
This patch enables error reporting and implements error_detected,
slot_reset and resume callbacks.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add support for system wide suspend/resume. During suspend, MHI
device controller must be put in M3 state and PCI bus in D3 state.
Add a recovery procedure allowing to reinitialize the device in case
of error during resume steps, which can happen if device loses power
(and so its context) while system suspend.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add support for resetting the device, reset can be triggered in case
of error or manually via sysfs (/sys/bus/pci/devices/*/reset).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Hardware channels have a feature called burst mode that allows to
queue transfer ring element(s) (TRE) to a channel without ringing
the device doorbell. In that mode, the device is polling the channel
context for new elements. This reduces the frequency of host initiated
doorbells and increase throughput.
Create a new dedicated macro for hardware channels with burst enabled.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
If the IPA (IP hardware accelerator) is starved of event ring elements,
the modem is crashing (SDX55). That can be prevented by setting a
larger number of events (i.e 2 x number of channel ring elements).
Tested with FN980m module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Fix the following warning with explicit cast:
warning: implicit conversion from 'unsigned long long' to
'dma_addr_t' (aka 'unsigned int')
mhi_cntrl->iova_stop = DMA_BIT_MASK(info->dma_data_width);
Fixes: 855a70c12021 ("bus: mhi: Add MHI PCI support for WWAN modems")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
This is a generic MHI-over-PCI controller driver for MHI only devices
such as QCOM modems. For now it supports registering of Qualcomm SDX55
based PCIe modules. The MHI channels have been extracted from mhi
downstream driver.
This driver is for MHI-only devices which have all functionalities
exposed through MHI channels and accessed by the corresponding MHI
device drivers (no out-of-band communication).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: fixed up the Makefile rule]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
